Used Hydraulic Section Bending Machine for sale (90,822)

Condition: excellent (used), Year of construction: 1986, plate thickness 5 mm sheet width 40 mm Caodpfxjxzk I So Ab Tsa

Condition: good (used), Year of construction: 1996, tube diameter 6 - 28 mm wall strength 2 mm bending radius min. 2 x D Control IPU 20 bending radius max. 5,0 x D mm bending angle max. 190 ° arbor length 3000 mm operating pressure 180 bar hydraulic motor 4 kW weight of the machine ca. 900 kg dimensions of the machine ca. 3,8 x 1,1 x 1,3 m Semi-automatic electro-hydr. mandrel tube bending machine with PLC control for 20 angles and display in the control panel for bending angle specification, angle detection and angle measurement via absolute value encoder, autom. tool plate reset, Turning device with digital display, hydr. quick chuck, aut. Mandrel lubrication, adjustable length stops. Operating modes: MANUAL and semi-automatic. Control buttons: hydraulics on / off, operating mode selection, clamp to / on, clamp forward / backward, mandrel forward / backward, bending forward / backward /, locking forward / backward, mandrel lubrication, turning device forward / backward, plate reset, length stop forward, emergency stop. The machine comes from a prototype construction and was only used a little until 2000. After that, the machines of this department were sold. However, the purchaser did not use the pipe bending machine and therefore it has only stood Casdpfsvtgn Nsx Ab Toa in the warehouse and has not worked since then ((original paint). Please notice that the price of a new machine today is over € 60.000,--. Machine dealer with own stock of 1600 m².

Condition: not inspected (used), Kramer plate rolling machine / three-roll plate bending machine Type: RHM III 75/650 Max. sheet thickness: 3.5 mm Bending width: 650 mm Right & left rotation Heavy-duty The machine comes from a company closure, offered at a special price, untested. Csdox An A Ajpfx Ab Teaa

Year of construction: 1994, condition: ready for operation (used), Immediately available ex location Hydraulic folding machine ONISMA (Spain) Model: P 3 x 10 Year of manufacture: 1994 Working length: 3050 mm Material thickness up to 10 mm Drive power: 15 kW Weight: 9 t Caedex Anc Aspfx Ab Tja Bending tools renewed in 2024. Price: EUR 7,500 plus VAT ex location

Condition: good (used), Year of construction: 1998, GEOTECHNIKA XZ 1000/1 3-roll round bending machine Caedoq Ix Anepfx Ab Tea 1000mm year 1998 weight 200kg

Condition: used, machine/vehicle number: SA9FT3A50MH17xxxx, Year of construction: 2021, Please contact ATS Norway for more information Please provide reference number upon request: 20727 Specifications: EU-approved until 07.05.2026 Model year: 2021 Tires: See photos Hydraulic loading ramps Manual widening Length: 1,095 cm Width: 254 cm Axle distance: 514 / 136 cm Curb weight: 7,000 kg Caodpfowvy Rzsx Ab Tja Tool compartment included Description:EU-approved and ready for immediate operation.Equipped with hydraulic loading ramps and manual widening.Available for quick delivery. Technical approved: Yes EU-approved until: 07.05.2026 Own weight: 7000 Total Weight: 28000 Payload: 21000 Width: 254 Length: 1095 Model: m/ hydrauliske kjørebruer

Condition: ready for operation (used), Year of construction: 2015, operating hours: 15,305 h, General Data Machine weight 3300 kg Measurements height 2020 mm Dimensions Machine Length 3920 mm Injection Unit Screw diameter 40 mm Clamping Unit Clamping force 700 kN Cjdpfxjxy Aqps Ab Tsaa This Arburg 370 S 700-290 U was manufactured in 2015. It features a screw diameter of 40 mm, injection weight of 172 g, and a clamping force of 70 t. The tiebar spacing is 370 x 370 mm, with clamping platens measuring 510 x 510 mm. Ideal for precision hydraulic injection moulding, consider the opportunity to buy this Arburg 370 S 700-290 U hydraulic injection moulding machine. Contact us for more information. Application Types Injection Moulding

Condition: used, Roller sets for section bending machine, 3-roll ring bending machine HERKULES WETZLAR The rollers fit a section bending machine HERKULES WETZLAR type BO 238 N Shaft diameter: 60 mm with 18 mm keyway 2 rollers set No. 1, roller diameter = 110 mm, roller width = 180 mm 2 rollers set No. 2, roller diameter = 160 mm, roller width = 40 mm 3 rollers set No. 3, roller diameter = 150 mm, for tube diameter Ø 33 mm, roller width 87 / 115 mm - Roller set No. 3 with adapter ring from Ø 93 to Ø 60 mm without keyway The machine had 2 driven rollers Casdpoglaq Ijfx Ab Tja Total weight of all rollers: 57 kg Good condition

Condition: new, tube diameter 33,7 x 3,4 GAS mm tube diameter 35,0 x 2,5 STAHL mm tube diameter 35,0 x 1,5 EDELST mm Caodpoxab E Sjfx Ab Tsa bending radius min. R10 - R 190 mm bending angle max. 0 - 180 ° tool taper 6-kant 40 mm voltage 230 V total power requirement 0,9 kW weight of the machine ca. 23,0 kg Description: - MediBender "070" digital - with maximum bending performance for 35 x 2.5 mm steel tubes - Excellent bending quality with very tight bending radii . (from 2 x tube diameter) and bending angles between 0° and 180° - Easy to operate - High accuracy and reliability - Fast tool changes (within seconds) - Easy to transport - Huge selection of affordable standard tools (metric, gas inch, inch) BENDING SEGMENT AVAILABLE FOR AN ADDITIONAL CHARGE

Year of construction: 1980, condition: good (used), with initial rounding Technische Daten:/ technical details Biegelänge / bending lenght 2000 mm max. Blechstärke / max. sheet thickness 20 mm Anbiegeleistung / initial rounding 15/11 mm Codpfx Ajkzg E Ajb Toaa Walzendurchmesser Unterwalzen / roll diameter below rolls 280 mm Oberwalzendurchmesser / diameter of the upper roll 300 mm Antriebsleistung Hauptantrieb / drive capacity main drive 16,2 kW Antriebsleistung Anstellantrieb Oberwalze / drive capacity upper roll 4,8 kW Antriebsleistung Anstellsntrien Unterwalze / drive capacity below roll 3,7 kW Gewicht ca. / weight ca. 14200 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding.

Condition: used, Year of construction: 2004, Technical details: tube diameter: 20 mm bending radius max.: 100 mm control for program: S7-300 tube pipe draw up length: 2270 mm air pressure - required: 7 bar total power requirement: 15 kW Bending speed: 540 °/sec control voltage: 24 V / DC V connection voltage: 400V / 50Hz / 3 Ph V dimensions L x W x H: Biegeaggregat: 1,8 x 1,4 x 1,6 m dimensions L x W x H: Zuführung: 1,2 x 1,5 x 1,55 m dimension machine xH: 3,0 x 1,0 x 1,2 m Mandrel tube bending machine Bending direction RIGHT Operation via SIMANTIC Panel PC control unit Pneumatics: Pressure 7 bar; flow rate 200 l/min. Hydraulics: Pressure 150 bar; flow rate 6.8 l/min. Equipment/Accessories: -oil drip tray 3.1 x 0.96 x 0.02m -Spare parts and accessories * Cedpsu Ibzkefx Ab Toaa

Condition: used, machine/vehicle number: WMM000000V004xxxx, Year of construction: 1997, Please contact ATS Norway for more information Please provide reference number upon request: 19250 Cajdpfjv U S Rrox Ab Tsa Specifications: - 3 axle - Turn on 1 - Hydraulic bridges - Good tires - 10 tonne axles - Ready for delivery Description: Mueller Machine towing from 1997. Trailers need a bit of maintenance against rust and dirt. Hydraulic brakes and good tyres. Ready for delivery. Technical approved: no EU-approved until: 31.01.2018 Own weight: 6100 Total Weight: 30000 Payload: 23900 Width: 252 Length: 1045

Condition: ready for operation (used), Year of construction: 2005, operating hours: 79,600 h, General Data Machine weight 22500 kg Clamping Unit Clamping force 4000 kN Injection Unit Shot weight 1860 g Cedpexy Anbjfx Ab Tsaa Screw diameter 90 mm This Arburg 820S-4000-3200 was manufactured in 2005. It features a clamping force of 4000 kN, a screw diameter of 90 mm, and a shot weight of 1860 g. The machine operates with a SELOGICA control system and has a total installed power of 96.2 kW. Consider the opportunity to buy this Arburg 820S-4000-3200 hydraulic injection moulding machine. Contact us for further details regarding this machine. Application Types Injection Moulding

Condition: used, We are offering a JUTEC 6000D tube bending machine here. Please refer to the attached offer for technical data. Csdsxz Rz Eopfx Ab Teaa If you have any questions, we are happy to assist you.

Condition: new, tube diameter 42.0 mm Stahl wall strength 3.0 mm Stahl tube diameter 54.0 mm CU/Alu bar material - diameter 30.0 mm wall strength 2.0 mm revolutions per minute 2.0 U/min voltage 230 Volt total power requirement 1.1 kW weight 80.0 kg range L-W-H 410 x 1000 x 570 mm ERCOLINA MediBender "MB 42 M" Caodpfx Abexaa Sds Tsa - Capacity steel pipe 42 x 3.0mm - Capacity gas pipe 1“1/4 gas x 3.5 mm - Capacity square profile (FE 42) 35 x 35 x 3 mm - Max. bending radius 10-260 mm - Minimum radius 2 x D - 6-edge tool holder - Min. outside diameter 5 mm - 1/8“ gas Equipment: - patented fast tool change system - one bending speed - freely movable foot switch - bending tools on request for an additional charge including ERCOLINA microprocessor control: - with 30 programs each program with up to 9 bending angles programmable - in addition, the necessary correction angles can be entered . for each bending angle in the working mode BENDING SEGMENT AVAILABLE FOR AN ADDITIONAL CHARGE

Condition: new, CNC Hydraulic guillotine shear New machine Manufacturer:UMS Type : PRO. 3100 x 13 CNC Technical data: Cutting length 3100 mm sheet thickness (42 kgf/mm) 13 mm sheet thickness (70 kgf/mm) 8 mm cutting angle: 0,5 - 3 mm 15 pcs. blank holder Cybelec Cybtouch 8 monoblock: steel welded construction Automatic cutting gap adjustment Table with ball rollers High quality, hardened and ground upper and lower knives Light sensor for front side (sheet guide) Adjustable cutting stroke 1 m support arm with scale 1 m support arms ( 2 pieces ) Rear light sensor ( 10-16 mm sensor distance) Cutting line illumination Motor 30 kW throat 180 mm Cutting speed 7/13 Original Rexroth valves Rexroth hydraulic system Rexroth pump, original Eckerle Electrical parts from Siemens Operating instructions German Table height 900 mm Overall dimensions 3840x2830x2180 (WxLxH) Total weight 11.000 kg plus commissioning, training and transport Delivery time from order approx. 70 days Cjdpsnl D Tfsfx Ab Toaa

Condition: used, Year of construction: 1992, Technical details: tube diameter: 6 mm tube diameter max.: 16 mm bending angle max.: 90 ° electrics - voltage/frequency: 220 / 50 V/Hz Total power requirement: 0,75 kW Cedpfxewivn Ne Ab Tjaa Weight approx.: 0,145 t machine dimensions LxWxH: ca. 1,0 x 0,8 x 1,2 m Application: Mini tube bending machine with free bending head. Processing of precision steel tubes according to DIN 2391/C, material 35.4 NBK Ø 6 - 16mm. -With hydraulic drive -8-fold bending preselection angle up to 180 -Pipe stop length 1m -Emergency stop button -mobile with parking brake -pivoting pipe head (vertical in horizontal position) -required hydraulic oil = approx. 20 liters (e.g. Esso Nuto 32) Accessories: various bending tools *

Condition: used, machine/vehicle number: WFDFLT3305100xxxx, Year of construction: 2005, Please contact ATS Norway for more information Please provide reference number upon request: 21651 Specifications: Caedpfsxq Dc Uox Ab Toa 2005 model Tires (see pictures) Spring ring: steel spring ring Shift brakes Hydraulic driving bridge Lashing parties Ready for delivery Description: We have a 2005 Damm 3-axle machine trailer w/ hydraulic axles for sale. The machine trailer is EU-approved and functions as it should, according to the owner. Cosmetic damage may be present as it is from 2005. Ready for delivery Technical approved: Yes EU-approved until: 15.07.2026 Own weight: 6680 Model: 3 akslet maskinhenger m/ hydrauliske kjørebroer

Condition: ready for operation (used), Year of construction: 2015, operating hours: 15,642 h, General Data Measurements width 1810 mm Measurements depth 6950 mm Measurements height 2213 mm Machine weight 15750 kg Injection Unit Screw diameter 45 mm Clamping Unit Codpfjxy Anuox Ab Teaa Clamping force 350 ton Media Internal cooling Yes Additional Equipment Fanuc Robot This SUMITOMO SHI DEMAG Systec SP 350/720-840 was manufactured in 2015. It is a hydraulic injection moulding machine, ideal for precision plastic processing. Consider the opportunity to buy this SUMITOMO SHI DEMAG Systec SP 350/720-840 hydraulic injection moulding machine. Contact us for more information. Application Types Injection Moulding

Condition: new, Ostas SMR-S 2070x170 Premium - 3-Roll Plate Rolling Machine with Top Equipment Special price €19,500 instead of €22,100 excl. VAT Standard features: - Machine frame made from ST-52 steel - Large-diameter rolls made from SAE 1050 (CK-45) certified steel - Chain- and belt-driven helical gear for upper and lower rolls - Precision bending with brake motor - Rear roll motorized - Manually extendable roll - Conical bending device - Central lubrication system - Mobile control panel - CE-compliant - User manual Included additional features: - Digital readout for lower roll - Digital readout for rear roll - Lower roll motorized - Hardened rolls - Extended roll shafts for attaching profile and pipe bending rolls Cajdpfx Asiza Ryeb Tsa Optional equipment: - Profile/pipe bending rolls Technical data: - Bending length: 2,070 mm - Capacity with pre-bending: 5 mm - Capacity without pre-bending: 6 mm - Roll diameter: 170 mm - Min. bending diameter: 255 mm - Main motor power: 4 kW - Rear roll motor: 1.5 kW - Dimensions (W x H x D): 3,750 x 1,260 x 920 mm - Weight: 2,100 kg

Condition: good (used), Year of construction: 1991, 1 piece Hydr. hole punch MUBEA type HP 1000 / 760. Year of manufacture 1991 Punching force 100 tons With punching saddle for K 60-K260 and various tools, manually operated linear punching unit (raster rail 4 m) swiveling and digital display, carriage clamping and foot switch Dimensions L x W X H 1930 x 780 x 1980 mm Projection 760 mm Working height 1135 mm Hole 40 in 22 mm Casdpfetv Hzvsx Ab Tsa Stroke 0 - 70 strokes Number of strokes at full stroke 11 strokes Drive power 8.5 kW Weight 3800 kg 3600 kg Used, ready for operation

Condition: used, machine/vehicle number: YY9SE51MX9T01xxxx, Year of construction: 2009, Please contact ATS Norway for more information Please provide reference number upon request: 20343 Specifications: - 2009 model - 3 axles - Lift on 1 axle - Friction steering on 3 axles - Lashings - Ready for delivery Description: We have a 2009 Damm SE-51M 3 axles Machine trailer w/ hydraulic driving bridges for sale. The trailer is Eu-approved until 02.09.26 and can be put straight into production. It works as it should according to the owner. Ready for delivery. Technical approved: Yes EU-approved until: 02.09.2026 Own weight: 9750 Cedpfxewi Rlij Ab Tsaa Total Weight: 51000 Payload: 41250 Width: 255 Length: 1360 Model: SE-51M 3 akslet Maskinhenger m/ hydrauliske kjørebroer

Year of construction: 2007, condition: ready for operation (used), This Arburg 420A 1000-400 was manufactured in 2007. It features electromechanical main movements by servo drives, a modular plasticizing unit with adaptive temperature control, and a five-point double toggle clamping system with servo-electric adjustment. The Selogica control system enhances operational efficiency. If you are looking to get high-quality injection molding capabilities, consider the Arburg 420A 1000-400 machine we have for sale. Contact us for more information about this machine. Application Types Injection Moulding Csdpfxsxy An Io Ab Tjaa

Condition: new, Ostas ORM 1570x140 Premium - 3-roller sheet curling machine with top equipment Additional equipment included - Motorized rear roller - Digital display for rear roller Cedpfx Aouzhy Tob Tjaa - Hardened rollers Standard equipment - Cast steel main frame - quality-certified SAE 1050 steel rollers - top and bottom rollers with individual gears - conical bending device - Wire grooves at the end of the rollers - mobile control panel - Compliance with CE standards - user manual Technical data - Bending length: 1570 mm - Bending capacity: 4 mm - Roller Ø: 140 mm - Roller speed: 3.5 m/min - Motor power: 2.2 kW - Dimensions WxHxD: 2725 x 1100 x 800 mm - Weight: 1450 kg

Year of construction: 2002, condition: ready for operation (used), Injection Unit Screw diameter 40 mm Codexyazfspfx Ab Tsaa This Krauss Maffei 150-520 C2 was manufactured in 2002. It features a screw diameter of 40 mm and includes a Sepro robot and a storage conveyor belt from 2014. The machine is operational, with pump operating hours at 50,327 and automatic operating hours at 36,908. Consider the opportunity to buy this Krauss Maffei 150-520 C2 hydraulic injection moulding machine. Contact us for more information about this machine. Application Types Injection Moulding