Profile bending machine IMCAR - CPH 80

IMCAR CPH 80

Condition: good (used), Year of construction: 1998, control type: NC control, number of rollers: 4, roller (bottom) diameter: 540 mm, roller (top) diameter: 560 mm, side roll diameter: 420 mm, roller diameter: 440 mm, roller length: 3,100 mm, sheet thickness (max.): 60 mm, overall weight: 45,000 kg, total length: 8,700 mm, total width: 2,900 mm, total height: 3,075 mm, power: 81 kW (110.13 HP), Equipment: cone bending device, documentation/manual, 4 roll plate bender HAEUSLER - VRM-hy MACH-ID 9638 Make: HAEUSLER Type: VRM-hy Year: 1998 Smallest bending diameter 640 mm Pressing force against upper roll 5800 kN Conical bending attachment Central lubrication Equipped for change rolls 570 / 500 / 430 mm Rolling width: 3100mm Rolling thickness 3x toproll Ø:50mm Rolling thickness 5x toproll Ø:60mm Rolling thickness prebending: 40mm Top Roll Ø: 560+440mm Bottom Roll Ø: 540mm Side roll Ø: 420mm Number of rolls: 4 Rolling speed: 0-6 Adjustiment lower roll: 0 - 200mm/min. Adjustment side rolls: 0 - 500mm/min. Number of driven rolls: 2 Power: 81kW Fedpfxszbqquj Akyogh Length: 8700mm Width: 2900mm Height: 3075mm Weight: 45000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: as good as new (ex-display), Year of construction: 2007, I - beam section - flat steel 50 x 10 mm I-beam section - upend 80 x 15 mm L-beam 50 mm round material 30,0 mm bar material dia. max. 1 1/2" mm bar material - diameter 30,0 mm weight 185 kg range L-W-H 670 x 530 x 1350 mm square material 40 x 40 x 3 mm pipes 60 x 2,0 mm Thickness of tenon 30 mm total power requirement 0,75 kW Demonstration device Equipment: • Base frame of the machine • Foot switch • Standard-rolls (divided) • Possible to bend horizontally and vertically Fgsdpfx Aket U R H Ueyeh • machine has only one drive (right-left-run)

Condition: new, Year of construction: 2025, Sheet metal folder ZGR-3140/1.0 We have a new, high-quality folding machine of 3140 mm/ 1.0mm. This machine guarantees very high quality and agility of the work doing by the roofers. Our main task is the production of folding machines, with which we are concerned many years. The bending machine is equipped in degree scale, Romans screws, rear frame and gas struts. Directly from manufacturer! - max. working length 3140 mm - steel plate to 1.0 mm - our machines bend both a copper sheet and aluminum sheet - the total weight of machine is 600 kg - the clearance between the lower beam (fixed) and the upper beam (pressed) of 80 mm - bending angle of 145 degrees - thickness of the bending beam of 20mm - new, full machine - delivery to the client - certificate CE - TAPPING ANGLE IS FREE !! Price excl. shipping We provide invoices with 0% of tax. Fgedpfx Aochwa Dokysh Delivery every week :)

Condition: excellent (used), functionality: fully functional, Year of construction: 2000, machine/vehicle number: 3roll 3500x140 mm prepinch, control type: manual, degree of automation: manual, actuation type: hydraulic, controller manufacturer: MG, controller model: MG, number of rollers: 3, roller (bottom) diameter: 880 mm, roller (top) diameter: 950 mm, side roll diameter: 880 mm, roller length: 3,550 mm, working width: 3,500 mm, working height: 3,950 mm, sheet thickness (max.): 140 mm, sheet thickness steel (max.): 175 mm, overall weight: 200,000 kg, total length: 8,800 mm, total width: 5,100 mm, total height: 5,775 mm, power: 200 kW (271.92 HP), input voltage: 380 V, input frequency: 50 Hz, number of digital displays: 2, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, Hydraulic Plate Bending machine planetary pinch pyramid with prebend. model MG35140V 3 roll capacity 3500x140 mm The machine was overhauled in 2024, Capacity : Plate width mm. 3500 Plate thickness mm. 140 Capacity chart in enclosed Tech data: Fgjdpoyzim Aofx Akyeh -3 rolls driven hydraulic motorized with axial gear unit on each roll independent -Synchronized hydraulic rotation of the 3 rolls with variable speed. -Planetary design with pre-pinch fully hydraulic -Conical plate bending with hardened contrast pad -Digital position readouts of the bending rolls -Rolls installed on bearings double crown heavy duty -Overload safety hydraulic operation protection of the 3 rolls -High pressure hydraulic power pack with multi-pumps oil feed -Centralized control panel electric on wheels with joysticks and digital readouts -Emergency stop with safety system around the machine working area Rolls surface length mm. 3550 Top roll mm. 950 Side rolls mm. 880 Electric power on hydraulic unit Hp 100 + Hp 100 Voltage 380 Vac / 50 Hz Configuration & accessories installed with the machine -Hardened surface of the 3 rolls -Conical plate bending attachment , rolls tilt with contrast roller type. -Centralized operator panel with directional joysticks electric. -Digital position readout of the bending rolls. -Emergency and safety installations, certified CE -User manuals and instruction books in English -Dimension see layout drw in enclosed

Condition: good (used), Year of construction: 1999, functionality: fully functional, turning length: 3,000 mm, turning diameter: 1,000 mm, spindle bore: 197 mm, Upon request, videos of the machine in operation can also be provided. Maximum turning length: 6000 mm Turning diameter: over cross slide: 1000 mm over bed: 1250 mm Fgjdpfx Aeyr N N Rekyeh Spindle bore: 197 mm Spindle speeds: 0 – 665 rpm Faceplate diameter: 1200 mm Workpiece weight: 15000 kg between centers Motor power: 55 kW / 74 hp 3 gear stages: 1.5-55 / 50-180 / 180-665 rpm Accessories: Sauter 4-position tool turret (rotation defective) Tailstock (hydraulics partially defective, pressure loss) Chip conveyor 2 chip guard doors (incl. safety device) 4-way bed machine (flat bed) LED lighting

Condition: used, 3-axle truck trailer, low-loader trailer MÜLLER MITTELTAL Type AZP Curtain-sided low loader, low-loader trailer, low loader for machine transport First registration: 2001 Total mileage: approx. 350,000 km Gross vehicle weight: 24,000 kg Unladen weight: 5,500 kg Payload: 18,500 kg Platform height: 840 mm Loading height under tarpaulin frame: 3,200 mm Fgedpfx Aket N Anteyjh Platform length: 7,450 mm Overall length: 9,150 mm Overall width: 2,550 mm Overall height: approx. 4,050 mm Axle load front: 8,000 kg Axle load middle: 8,000 kg Axle load rear: 8,000 kg Tyres: Michelin 215 / 75 R17.5 (135/133J XTE 2+ TL) - Rear wing doors at drop side height - Tarpaulin frame with EDSCHA roof system - Tarpaulin frame designed for easy removal (can also be used with the frame removed and the tarp pushed forward) - Spare wheel mounted on the front wall - Independent lifting and lowering of front and rear axles - Middle axle with lift function - Drawbar – extendable in multiple stages - Heavy-duty lashing rings on the outer frame and in the vehicle centre - ALU drive-on ramps, length 268 cm, width 410 mm, height 130 mm (surcharge EUR 2,000 net) The trailer was purchased new by us and is therefore first-hand. The trailer has been deregistered since 2025.

Condition: used, Year of construction: 2009, faceplate diameter 3000 mm swing diameter 3500 mm turning height 3200 mm Control Fanuc type Series 320i Model A slide adjustment 1750 mm ram head dimension 300x300 mm x-axis 2700 mm Table load 30000 kg main drive motor 100 kW Tool changer 16 weight of the machine ca. 89 t dimensions of the machine ca. 8,5x6x8 m No. 1104 The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team Fgodpfx Akeyqu Rwjyoh

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: three-phase, warranty duration: 12 months, Equipment: cabin, Paint/spray booth dimensions without fan and control Panel! Extraction surface - dimensions (mm): 4430(w)x1900(h) Overall dimension(mm): 4530(w)x2350(h)x1910(d) Technical data: - Fan power 4.4kW (ATEX) - Fan suction capacity: 24000 m³/h (max 1200Pa) Fjdoia Taxjpfx Akyegh - Lighting: 2 pcs 2x58W (ATEX) - Connection voltage: 400V - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX - Complete technical documentation - CE Documentation - Warranty Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us

Condition: as good as new (ex-display), Year of construction: 2023, Container rotating device, 10-ton lifting capacity Speed: continuously adjustable Hand and foot remote control Diameter: 320mm to 2800mm Roller diameter: 300mm Fgedpsd Nmx Tofx Akyjh Speed: 6 - 60 m/h Power: 2 x 0.55 kW

Condition: excellent (used), Year of construction: 1984, functionality: fully functional, turning diameter over cross slide: 630 mm, spindle bore: 320 mm, turning diameter: 1,200 mm, turning diameter over bed slide: 930 mm, turning length: 3,000 mm, Lathe in very good technical condition, has seen very little use and was not used for machining pipes. The Poręba TPL 90/3m lathe (also listed in market nomenclature as a variant of the TPK 90 series) is a textbook example of an Oil Country Lathe / Hollow Spindle Lathe. This model fulfills all the specific criteria for machines intended for the Oil & Gas sector: • Massive spindle bore (Big Bore): This version features a spindle bore with a diameter of 320 mm (approx. 12.5 inches), allowing for easy insertion of thick-walled drill and casing pipes. • Dual chucking system: The headstock is designed for mounting two independent lathe chucks (front and rear, typically 28 inches in diameter), ensuring the pipe is clamped and stabilized at both ends of the spindle. • Optimal working dimensions: The 3m designation defines a turning length between centers of 3000 mm, which, combined with a swing over bed of 930 mm (hence the "90" in the name), allows for machining heavy-duty pipeline components. Fgodpsy Sf Azefx Akysh • Exceptional rigidity: FUM POREBA factory machines are renowned for their monolithic, very wide and heavy cast iron beds, which effectively dampen the immense vibrations generated during taper thread cutting. In international used machinery catalogues, this specific Poręba model is directly classified under the Oil Field Lathes category. TECHNICAL SPECIFICATIONS: Geometric parameters and machining ranges • Swing over bed: 930 mm / 36.6 in • Swing over cross slide: 630 mm / 24.8 in • Swing in gap: 1200 mm / 47.2 in • Maximum turning length between centers: 3000 mm / 120 in • Bed width: 585 mm / 23.0 in Headstock • Spindle bore diameter (Hollow Spindle): 320 mm / 12.6 in (in US nomenclature classified as a 12.5" version) • Spindle speed range: 5 – 250 rpm, or modified versions up to 710 rpm • Number of spindle speed steps: 18 Feed and thread cutting system • Longitudinal feed range: 0.1 – 12.8 mm/rev / 0.004 – 0.504 in/rev • Cross feed range: 0.05 – 6.4 mm/rev / 0.002 – 0.252 in/rev • Types of threads cut: Metric, Inch (Whitworth), Module, Diametral Pitch (DP) Tailstock • Tailstock quill diameter: 130 mm / 5.1 in • Tailstock quill travel: 300 mm / 11.8 in • Internal taper of quill: Morse No. 6 (MT6) Drive and dimensions • Main motor power: 22 kW / 29.5 HP • Overall length: approx. 5500 mm / 216.5 in • Overall width: approx. 1750 mm / 68.9 in • Overall height: approx. 1500 mm / 59.0 in • Total weight: approx. 8000 kg / 17,630 lbs