Used Finger Press for sale (12,957)

Condition: excellent (used), Self-loading press for gluing Orma LS/ECO/CA 30/13 Working length 3000mm Working width 1300mm Automatic material loading Glue application system Shelves heated with oil to 130C Top pressure force 57t Side pressure force 9t Year of production 2001 CE certificate Gbedpfx Aov Nhx Uskyju

Condition: used, Year of construction: 2010, No. 3214 Feed-through veneer press Sergiani LAS Plus Used, year of construction 2010, already dismantled and stored Automatic press with continuous operation for the production of barrier doors, finished doors (veneer doors, HPL, CPL) and pre-treated parquet (2 - 3 layers). The press can be used to load the workpieces one after the other, while the pressure in the other compartments is kept constant. Up to 2 employees are required to operate the line. The multi-daylight press enables a very high production output. The pressing time is approx. 3 minutes (180 seconds) and is spread over 10 levels, which means that the press opens every 18 seconds and a new panel is processed. The press has already been dismantled and stored. The system was in operation until it was dismantled. The previous owner produced 3-layer parquet with the system. The bottom layer was inserted manually. The middle layer consists of one piece. This was glued at the top and bottom and automatically inserted into the system. The top layer was also inserted automatically. Glue spreader / glue applicator not included (optionally available) Stages: 10 Pressing force: approx. 5.5 kg/cm² Total force: 200 tons Panel size: approx. 2500 x 1300 mm LW Heating: Hot water Area of application: Production of doors, laminating, veneer and wood-based material processing High productivity with a capacity of up to 1200 doors per shift (factory specification) Vacuum loading system with 2-lane infeed roller conveyor, without gluing Scissor lift table with loading belt (belt approx. 2900 x 1000 mm LW) Vacuum stacking station with outfeed roller conveyor Space requirement for press with loading table approx. 6500 x 2365 mm LW Space requirement for entire production line approx. 25000 x 5710 mm LW Sale on behalf of customer, ex location near 5020 Salzburg (Austria), without transportation and assembly Loading and transportation by us optionally possible Gbedpfev Sthgjx Akyju Subject to errors in the description and price To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Pictures and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices excl. VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: new, Promess servo press KA-EMF80 80 kN, new, with DMS amplifier Manufacturer: Promess Type: KA-EMF80 Type: Servo press kN: 80 Condition: New Calibrated: Yes DMS amplifier: BA 624.u2 Gedpfx Akergn Nnoyobu More servo presses, new and used, can be found in our shop! International shipping costs available upon request!

Condition: like new (used), Year of construction: 2018, functionality: fully functional, operating hours: 540 h, pressing force: 1,000 t, stroke length: 800 mm, reverse speed: 150 mm/s, table width: 2,300 mm, table length: 3,000 mm, total length: 4,500 mm, total width: 3,500 mm, total height: 6,000 mm, overall weight: 101,000 kg, working height: 1,300 mm, working range: 1,300 mm, Hydraulic press 1000t - in very good condition, used for stamping first series parts from progressive tools Gbodpeyilh Iefx Akyou -we bought this maschine as new for 340 000 EUR in year 2019

Condition: new, pressure 8,0 kN stroke 40 mm throat 90 mm Working height from to 50 - 200 mm table surface area 120 x 160 mm weight of the machine ca. 22 Kg dimensions 160 x 230 x410 mm Knee lever hand press with fine height adjustment SPECIAL PRICE!!! • Working height adjustable by simply loosening the clamping screws on the stand • Working height fine adjustment for HK 800 = adjustment of the press head to the desired working height. The fine adjustment takes place Gbedpfofv Avksx Akysu forced in both directions via a threaded spindle • Hand lever arranged in a user-friendly manner, return via spring

Condition: new, pressure 8,5 kN stroke 40 mm throat 95 mm Working height from to 95 - 240 mm table surface area 160 x 110 mm Gbjdpfx Aksfv Awaoyou spindle diameter 25 mm weight of the machine ca. 27 Kg dimensions 160 x 230 mm

Condition: new, pressure 500 t column daylight 600 mm stroke 600 mm table surface area 3500 x1500 mm 600 mm feed down 8 mm/sec feed up 16 mm/sec travel on the bed 2200 x 900 mm total power requirement 30 kW weight of the machine ca. 28 t 2. STANDARD EQUIPMENT FRAME - Welded steel frame - Frame and plates are precision-milled using a CNC milling machine - Chrome-plated cylinder - Worktop with threaded holes HYDRAULICS - Bosch Rexroth hydraulic pump - Hydrapack or Badestons hydraulic directional control valve - Hydraulic block in accordance with EN standards - 1000-liter hydraulic oil tank - Pressure adjustment via pressure transmitter/regulator ELECTRICS - Control cabinet in accordance with EN standards - All cables are labeled and clearly arranged - All electrical components are from Siemens CONTROL PANEL - Stroke control in any position - X, Y, and Z-axis movement via remote control - Stroke adjustment via sensor SAFETY - The machine complies with the EC safety standards 2006/42/EC Machinery Directive, EN ISO 16092-01 and 16092-03 - Two-hand operation - Emergency stop button - Safety rope with switch around the press 4. TRANSPORT AND INSTALLATION – The price includes transport costs, installation, and training at the customer's factory. Gbjdpfx Akjfv Awhoysu – Hydraulic oil is not included in the price. – All handling costs (e.g., crane, forklift, etc.) are borne by the buyer. 5. WARRANTY – The machine has a 2-year manufacturer's warranty. – This warranty covers the delivery of all spare parts required for repair and service of the machine. Damaged parts will be returned to the manufacturer after replacement with a new part. – This warranty does not cover parts damaged due to improper use.

Condition: new, New Transfer press line from min. 300t up to max. 3500t. We offer new mechanical and hydraulic presses for various applications, individually tailored to your needs. Give us your requirements and we will make an attractive offer with installation and service. ISGEC has delivered to more than 26 countries in recent years, including Thailand, Indonesia, Vietnam, USA, Germany, Spain, France, Brazil, Hungary, Mexico, Bangladesh and over 200 presses to 40 Japanese customers. We are proud to be official sales partner since 2020 and look forward to hearing from you. Gsdpfxsf Rt Ubo Akysbu

Condition: new, Motor: 750W - 230V - 1 Phase Drilling capacity: 20 mm Spindle stroke: 85 mm Spindle taper: MK2 Number of speeds: 16 Spindle speed: 220-2840 rpm Work table: 305 x 305 mm Base: 460 x 280 mm Column diameter: 72 mm Overall height: 990 mm Weight: 60 kg Packaging: 820 x 500 x 290 mm INCLUDED * Digital depth stop * CE protective shield * Laser guide * LED lighting * CE emergency stop Gbjdpjk Iuqyefx Akyeu * Drill chuck with MK2 taper * Ejector pin

Condition: used, pressure 2 t throat 150 mm stroke 150 mm table surface area 310 x 250 mm power requirement 2,0 kW weight of the machine ca. 0,6 t dimensions of the machine ca. 1,2 x 0,8 x 1,7 m Gbedpfetzv Hmsx Akyou Single column press - with table base - various press accessories

Condition: like new (used), Year of construction: 2004, HYDRAULIC PRESS FOR GLUING WOODEN ELEMENTS TO THE THICKNESS OF HSKG Category: VI - Hydraulic presses for gluing wooden parts. Gsdotrl R Aopfx Akyobu The HSKG device is used for gluing wooden cut-thickness parts under high pressure of hydraulic cylinders. The range of achievable crushing forces per cylinder is 5-11kN (horizontal) and 25-55kN (vertical). The gluing of elements is carried out in a stack with the dimensions of the loading field. Stack forming is carried out by hydraulic compression between the sliding vertical beams and the vertical slats of the transverse cylinders. Both stack forming elements are equipped with wooden or metal inserts corresponding to the profile of the slat stack. Gluing wooden elements from the thickness improves the quality of the frames, reduces the cost of machining, reduces the amount of wood waste. Technical and operational data ( of standard execution HSKG - 6m ) Number of loading fields pcs 4 Dimensions of a single loading field - loading height - length of slats in one field mm mm 1140 1530 Maximum width of slats mm 150 Maximum length of glued elements mm 3120 Installed power kW 3 Electricity supply V AC 3/N/PE, 400V 50Hz Control voltage V DC 24 Number of actuators on one field: mm mm O 50x100 - 3 pcs. O 80x100 - 3 pcs. External dimensions (L x W x H) mm 8120x1000x2300 Weight of the device kg 4800 At the request of the customer, we also make other configurations of pressure actuators control depending on the expected length of glued elements, as well as other lengths of individual working fields in different quantities in the whole press set, and working width of up to 220 mm maximum with increased pressure force.

Condition: as good as new (ex-display), Year of construction: 2026, Technical specifications: Laminated panel press from our showroom; Working area: width from 150 - 2,550 mm, height from 150 - 1,400 mm, depth from 150 - 700 mm; Variable pressure adjustment 300/700/1100/1400/1800/2200 dN (kg) of the side pressing beam; Variable pressure adjustment 500/800/1200/1500/1900/2200 dN (kg) of the top pressing beam. Simple operation via 6 separate push buttons, freely adjustable pre-selection of pressing time with automatic opening function, loading height 300 mm. Gsdpfsb Eln Djx Akyobu The machine is in our showroom and can be delivered immediately. Location: available from our warehouse in 54634 Bitburg.

Condition: new, Year of construction: 2026, Actually one showroom machine available. Very robust machine with high pressing force - is also suitable for producing a salable briquette quality * depending on the material. The large press cylinder and the 80 mm briquette make this possible. Our best-selling briquetting press series + Tried and tested, simple technology, for extremely low susceptibility to errors + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Surcharge for cooling unit + € 4.995 net, (can also be retrofitted later) * cools the pressing tongs (important from 3.5 hours) and the hydraulic oil * Cooling device recommended for regular use of more than 3.5 hours at a time. Briquette diameter: 80 mm Front bush: 125 mm Briquette stroke max .: 100 mm Briquette lift opt ​​.: 80 mm Output (depending on material): up to 200 kg / h * * depending on the bulk weight * based on a bulk weight of 200 kg per cubic meter Motor power: 9.2 kW 400 volts / 50 Hz / 3 phases Gbsdpfx Akexfwdsysu Length: 2095 mm Width: 1300 mm Height: 1700 mm Weight: 1250 kg Oil volume: 220 liters Silo diameter: 1200 mm Silo content: approx. 1 qbm Pump: 75 liters Hydraulic pre-compressor Cooling pressing tongs option: yes, with special accessory coolable pressing tongs Hydraulic oil cooling option: yes Cooling of the pressing tongs and the hydraulic oil with cooling device (special accessory) Level monitoring option: yes Strand briquette option; yes (depending on material) Option of enlarged filling slide: yes, with special accessory enlarged filling slide CE compliant . Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18% - Chip length maximum 20 mm - Installation temperature: temperature-controlled room at at least + 5 ° C - The loading must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear

Condition: new, Year of construction: 2025, HIDRAULIC BOOK PRESS Gbedpfx Aksbyhnksyju PK-55x38 H -is a double press of very new conceiving for books and agendas -it is quick and simple to use -maximum size of material; 550x380 mm -the new model has a timer

Year of construction: 2026, condition: as good as new (ex-display), Vacuum Membrane Press The VP series is the optimal solution for woodworking. The VP 3000 is equipped with heating technology, which shortens the drying time of the adhesive, thereby increasing performance. Possible applications: Veneering / Form gluing / Coating... Coating of various profiles (veneer, paper, plastic...) Wood bending: Production of bent and laminated components The heating system is equipped with temperature control. Rubber membrane 2.5 mm Table top is made of plastic, 12 mm Oil-free Becker vacuum pump, 25 m3/h The control system for the vacuum / tank capacity is 15 l Working area: 3000x1500mm Heating system temperature: Max. 60 degrees C Heating system: 4.5 kW Pump power: 0.75 kW Gjdpfedwh E Aox Akyobu Vacuum pump capacity: 25 m3/h Rubber membrane External dimensions: 3100 x 1650 x 1600 mm Weight: 450 kg The machine is equipped with a chassis. Location: Available ex-stock in 54634 Bitburg - free loading -

Condition: as good as new (ex-display), Year of construction: 2024, New hydraulic heating plate press Manufacturer: ITALPRESSE, Type XL/6 30-13 with gold-anodized plates Touch display control - Electric heating plates, 3,000 x 1,300 mm - Total pressure: 90 tons - Number of heating plates: 2 pcs. - Number of tiers: 1 pc. Gsdpfxodx R Tfs Akyjbu - Cylinder stroke: 350 mm - Tier opening: 350 mm - All-side loading - Number of pressure cylinders: 6 pcs. - Diameter of pressure cylinders: 85 mm - Power requirement of hydraulic unit: 3 kW - Electric heating plates made of solid, hard aluminum with built-in heating wires - Heating power: 22 kW - High-pressure insulation plates - Working temperature: 90° C - Max. temperature: 120° C - Operating voltage: 400 V/50 Hz - Safety regulations according to CE standard Standard equipment: - Movement of the press table with rack and pinion and parallel guides at 2 corners of the press table, made of self-lubricating material - Electronic control unit with touch screen for controlling and monitoring the machine - Digital timer for setting the pressing time and automatic opening - Digital input and monitoring of the pressing pressure - Digital timer for setting the pressing time - Digital diagnostics and display of error messages - Safety circuit with two-hand operation - Safety pull cord - Safety bracket for the lower press table Integrated accessories: - Touch screen TS/400 - EFC Electronic flatness control - Gold-anodized heating plates (bus bars) Location: In stock at 54634 Bitburg - Immediately available -

Condition: like new (used), Handling equipment for a finger jointing line. Roller conveyors, wide- and narrow belt conveyors, a trim saw conveyor, Gsdpfx Aod Duz Eekysbu trim saws, etc. See pictures. With documentation. Good condition, made by Martek in Finland.

Condition: good (used), Year of construction: 2007, frame press GOMA PHA 3500 Door Press hydraulic Location Gorzów Wlkp. Conditions of delivery OWN RECEIVING Cost of delivery to be negotiated Startup type to be negotiated Description Gbjdpjdntc Nsfx Akyou Comments Working space 3500 x 2300 mm 1000kG (daN) pressure, engine at hydraulic unit 2,2 kW lenght 3500 mm hight 2300 mm weight 2000 kg agrageate hydraulic

Condition: excellent (used), Year of construction: 2018, HCV sling beams 2.2 tons - length 2m; Beam 6 tons - length 5m; Beam - 6 tons 6m; 6 tons 7m. About 50 pieces available in the offer. Price depends on lifting capacity, quoted price is for 1 piece. Gsdpjxl Rutsfx Akyobu

Condition: new, Year of construction: 2026, FLAT PANEL CASE CLAMP GANNOMAT "CONCEPT 70 EASY 170" Fully equipped in standard configuration with: Gbodpfxjw Sgnke Akysu - Sturdy, torsion-resistant steel frame made with welded and bolted construction - Lateral pressing beam with continuous pressure surface, equipped with a 25 mm thick coated support plate - Counter-pressure surfaces (side pressure wall, base) are continuous, 25 mm thick coated support plates - Electromotoric adjustment of the pressing beam via precision trapezoidal threaded spindles (with increased pitch and concentric accuracy) and high-performance carriage nuts with grease reservoir - Pressing is performed by electromotor via worm gear motor (0.75 kW) - The pressing force of the pressing beam is infinitely variable and electronically set via potentiometer, regulated by frequency converter, allowing completely wear-free pressure force control - Pressing force for vertical pressing beam: min. 300 daN (kg) up to stepless max. 2200 daN (kg) - Pressing and adjustment speed of the pressing beams with fine positioning, via 3-stage selector switch: 5 / 10 / 25 mm per second - Jog mode for precise positioning of the pressing beam, e.g. for low pressing forces such as drawers, etc. - Extremely simple operation via two separate pushbuttons; two motion sequences (open/close) can be selected via controller - Freely adjustable pressing time preselection 0–30 min (switchable to seconds or hours), with individually programmable opening dimensions for both pressing beams - Re-pressing function to increase or decrease the pressing force during the pressing process - Working height/loading height: 200 mm - Working dimensions: Length min: 150 mm, max: 1300 mm Height min: 150 mm, max: 1700 mm Depth: 700 mm Electrical connection: 400 Volt, 50 Hz, 16 A Available: at short notice

Condition: excellent (used), Briquetting machine POR Oscar 9kW Average briquette output: 130-180 kg Gbedpfx Akjxdahysyeu Briquette diameter: 70 mm Motor power: 9 kW Feeding hopper diameter: 1170 mm Technical documentation CE mark Machine weight approx. 800 kg

Condition: new, functionality: fully functional, Year of construction: 2026, power: 3 kW (4.08 HP), input voltage: 400 V, input current: 6 A, input frequency: 50 Hz, reverse speed: 14 mm/s, total length: 1,150 mm, total width: 850 mm, total height: 1,800 mm, Special Offer – 5% Discount Available! Hydraulic C-Frame Press – 250 kN (25.5 Tons) The Hydraulic C-Frame Press is a professional industrial machine designed for precise pressing, straightening, bending, assembling and forming operations. Its open C-frame construction provides excellent access to the working area, allowing convenient machining of larger workpieces and easy material handling from multiple sides. The rigid welded steel frame ensures maximum stability, durability and long service life. The precision hydraulic system provides smooth control of both pressing force and ram speed, delivering reliable performance and high machining accuracy. This versatile press is suitable for industrial production, maintenance departments, tool rooms, metalworking workshops and automotive applications. Main Features • Pressing force of 250 kN (approx. 25.5 tons) • Open C-frame design • Heavy-duty welded steel construction • Precise hydraulic control • Smooth ram movement • Excellent access to the working area • Suitable for industrial and workshop applications • CE certified Technical Specifications • Pressing force: 250 kN (approx. 25.5 tons) • Maximum hydraulic pressure: 25 MPa • Maximum opening: 500 mm • Ram stroke: 200 mm • Table dimensions: 500 × 400 mm • Throat depth: 200 mm • Downward speed: 10 mm/s • Return speed: 14 mm/s • Motor power: 3 kW • Packed dimensions (L × W × H): 1150 × 850 × 1800 mm Applications • Pressing • Bending • Straightening • Assembly operations • Metal forming • Metalworking workshops Gbjdeyr Ek Ropfx Akyju • Automotive industry • Tool rooms • Industrial manufacturing Transport and Delivery The machine is supplied brand new and includes a 12-month warranty, warranty service and professional after-sales support. We provide professional transport throughout Europe using specialized machinery logistics. Every machine is securely loaded, protected during transport and delivered directly to the customer's premises. We also assist with export documentation and international shipping arrangements. Worldwide shipping is available upon request. About Metal Technics Polska Metal Technics Polska is a manufacturer and distributor of professional metalworking machinery. We supply high-quality machines throughout Europe and provide expert technical advice, spare parts and comprehensive after-sales support. Contact us today for pricing, delivery times, machine availability, additional photos, videos or a personalized quotation.

Condition: ready for operation (used), Year of construction: 2023, 3-meter automatic wood length gluing press Godpfx Aoylqc Eskyebu

Condition: ready for operation (used), Working width 3450 mm Working height 2000 mm Number of cylinders 5 St. loading dimensions L x W x H 3600 x 1200 x 2720 mm Hess "Multipress" Perforated Plate Press For all sloped, segmental, and round-arch windows and doors. Also for interior work or frame construction. For gluing staircase block joints and much more. Largest working area approx. 3450 x 2000 mm External dimensions approx. 3600 x 1200 x 2720 mm The vertical perforated plate press is constructed of heavy-duty, torsion-free Godpswqr R Aefx Akyebu steel. Thanks to its simple, robust, and economical design, it has a long service life. The perforated plate is made of 10 mm sheet steel with a 50 mm hole pattern. The pressure cylinders and abutments are self-locking. 5 plug-in hand hydraulic cylinders on a perforated plate with a built-in pump, 2000 kp pressure relief valve, 140 mm pressure plate width, 80 mm pressure plate depth, 60 mm cylinder stroke 4 fixed individual abutments (Technical specifications according to the manufacturer - no guarantee!)

Condition: excellent (used), total length: 3,500 mm, total width: 1,300 mm, overall weight: 7,000 kg, operating pressure: 300 bar, transport length: 4,350 mm, transport width: 1,600 mm, transport height: 2,350 mm, Simimpiantin Shelf Press for Veneering 3500×1300 Shelf length: 3500 mm Shelf width: 1300 mm Two loads Press with 8 cylinders Shelves heated with water from central heating Godpfxoxxpgbs Akyjbu Max. working pressure: 300 bar Piston diameter: 80 mm Machine weight: 7000 kg Machine dimensions: 435×160×235 cm (H)