Used Energy Production for sale (16,484)

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Machine no. No. 122481 Year of construction 1984 Pressure capacity 100 ton. throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Rear upright width 735 mm Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Njdpfxju Rwa Ie Ahvoku Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Motor power 11 kW Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter - Clamping pin bore with clamping piece - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Weight 8.3 tons Good condition

Year of construction: 2017, condition: excellent (used), HIGHLY AUTOMATED, MODULAR SYSTEM FOR DIGITAL BOOK PRODUCTION ("BOOK ON DEMAND") AND SHORT RUNS – TECNAU LIBRA 800 Intended Use: Suitable for the conversion and processing of short runs and single copies ("books of one") with variable sizes, page counts, and covers. Performance: from print run 1; up to 800 copies per hour Book Format: min. 100 x 125 mm / max. A4 Thickness: min. 2 mm / max. 60 mm Nkjdsylyhdjpfx Ahvou Equipment / Further Details: Line Configuration: 1.Roll-to-Stack Feed: Unwinder, merger, Dupla cutter, and book assembly station for the production of book blocks with 2-up printing. 2.Sheet Feeder: A variable number of loose sheets can be added as inserts to the book block. The sheets must have the same size and print run as the book block being processed. 3.Infeed to Binder: Manual feeding station for pre-fabricated book blocks, conveyor with scanning station, book turnover module, and robotic loader at the binder. 4.Variable Binder: For the production of softcover books. The binder is equipped with PUR for the spine and hot-melt glue for the side gluing. 5.Softcover Cover Feeder: Configured with a sheet cover feeder; pre-printed covers are fed, trimmed at the front, side-trimmed, and creased to the exact thickness of the corresponding book block. 6.Cooling towers can be reordered as needed by the customer. 7.Variable Three-Knife Trimmer: Suitable for trimming books with variable dimensions in three axes and different cover types. 8.System Control Software Finishing Line The entire process is controlled via 2D Data Matrix codes. Through the code, the system receives authorization for the following automatic settings and workflow control: • Information on book dimensions and inserts (quantity and sequence) • Binder setup (spine position, thickness, and length) • Cover preparation: Softcover → creasing, cutting, edge trimming • Correct book-to-cover matching • Three-knife trimmer (blade positioning is automatically adjusted to the book dimensions)

Condition: used, Brand: Subal Model: T20 Year of manufacture: 2010 Compliance: CE standard Integrated equipment: - Automatic dough divider-rounder - Intermediate proofing station - Horizontal moulding machine - Optional small bun cutting up to 50 g Performance & Production: - High productivity for bakeries and industrial workshops - Automated operation for optimum time savings - Consistency and precision in moulding Ideal for: Industrial bakeries Large pastry shops Nodpfx Ahsym Uk Asvoku Bread production facilities

Condition: used, Production line consisting of: (1) Twin-screw extruder Technical details: Screw diameter 75 mm, capacity: max. 200 kg/h, KraussMaffei-Berstorff control system, weight 3.5 t /// Drive: SIEMENS 2860 / 30.5 rpm, 5,070 Nm, weight 1.2 t (1) Calibration table Technical details: four (4) SPECK pump units, length approx. 6 m, weight 2.7 t (1) Haul-off unit + punching unit + guillotine unit Technical details: Contact length approx. 2.5 m, unit length approx. 8 m (1) Tilting table Technical details: Tilting of profiles, table length approx. 6,000 mm Nodpfx Aex I Inxehvsku

Condition: used, Production line consisting of: (1) Twin-screw extruder Technical details: Screw diameter 75 mm, capacity: max. 200 kg/h, KraussMaffei-Berstorff control unit, weight 3.5 t /// Drive: SIEMENS 2860 / 30.5 rpm, 5,070 Nm, weight 1.2 t (1) Calibration table Technical details: Table length approx. 6 m (1) Haul-off unit + punching unit + guillotine unit Nkodpjx I Ig Uefx Ahveu Technical details: Contact length approx. 2.5 m, unit length approx. 8 m (1) Tilting table Technical details: Length approx. 6,000 mm (1) Twin-screw extruder Technical details: Screw diameter 90 mm, max. capacity 300 kg/h, BMCsmart control panel, weight approx. 3 t /// Drive motor HENSCHEL T1MAX90 C-35L, serial number 43-220/5, weight approx. 1.5 t (1) Calibration table Technical details: Table length approx. 6 m (1) Haul-off unit + punching unit + guillotine unit Technical details: Contact length approx. 2.5 m, unit length approx. 8 m (1) Tilting table Technical details: Tilting of profiles, table length approx. 6,000 mm

Condition: used, Production line consisting of: (1) Twin-screw extruder Technical details: Screw diameter 75 mm, capacity: max. 200 kg/h, KraussMaffei-Berstorff control unit, weight 3.5 t /// Drive: SIEMENS 2860 / 30.5 rpm, 5,070 Nm, weight 1.2 t (1) Calibration table Technical details: Four (4) SPECK pump units, length approx. 6 m, weight 2.7 t (1) Haul-off/saw combination Technical details: Weight approx. 1.8 t, with two (2) IDE chip extraction systems ME AS 58 (1) Tilting table Nkjdpsx I I Ilefx Ahvsu Technical details: Length approx. 6 m, weight approx. 300 kg

Condition: new, Year of construction: 2025, functionality: fully functional, The weighing system is also designed for mixing up to 4 products. Each of the 4 units can be programmed individually. The system can be tested at our test center, 20 km from Frankfurt am Main. Features - Easy operation and cleaning - Convenient control via color touchscreen - Memory for various weighing recipes - Precise weighing results thanks to three-stage weighing: coarse/intermediate/fine dosing, each programmable individually - Tool-free format changeover Technical data - Weighing range: 20g to 4000g - Accuracy: up to 0.5g, depending on product - 6-liter weighing hopper Nkodpfx Ajya Ahvjhvsu - Max. speed: 60 weighing cycles/minute - Weight: 240kg - Material: stainless steel 304 - Connection: 220V / 50Hz / 6A

Condition: like new (used), Year of construction: 2020, operating hours: 5,500 h, functionality: fully functional, machine/vehicle number: XZHGB50-12050, Equipment: documentation/manual, PLEASE ONLY SERIOUS ENQUIRIES REGARDING VIEWINGS OF THE PRODUCTION LINE! WE DO NOT INTEND TO DISMANTLE THE LINE IN JANUARY; THE ADVERT COULD NOT BE PROGRESSED OTHERWISE. I am offering for sale a completely unique production line in Hungary. 1. The line manufactures trays suitable for storing 10 eggs, in either continuous or batch operation. From raw material preparation to final delivery, we are offering a complete system for sale. 2. The egg tray production line is located in Bátonyterenye, where a fully serviced industrial site provides all the infrastructure necessary for production. Nkedpfxoya Eh Es Ahvsu 3. The total output of the line is sold on the domestic market. The complete egg tray production line consists of several units: - Material preparation system, which processes waste paper into mouldable raw material. - HGHY egg tray forming unit, which finalises the trays by drying and hot-air pressing after moulding. - Palletising system, which makes the finished trays ready for transportation. - Auxiliary systems for air, vacuum, power, gas, and water supply.

Condition: ready for operation (used), Year of construction: 2003, Complete Tetra Pak line TBA 21-1000 Slim, includes: 1. TBA/21 1000 Slim filler, V050, YOM 2003, 52.000 running hours 2. CAP30 cap applicator for Helicap23 Pro26 3. Easy Ride Terplus cartons accumulator 4. TCBP70 wrap around packer Nsdpfsycwvaex Ahveku 5. Conveyor system 6. Conveyors system The line is in very good condition, still in production till April. Can be sold without CAP30 applicator.

Condition: used, functionality: fully functional, Year of construction: 2022, operating hours: 380 h, load capacity: 300 kg, empty load weight: 2,960 kg, construction width: 1,460 mm, working height: 1,000 mm, Scissor lift Nodpfx Aoxqu H Rjhvsku Technical condition: very good Battery condition: very good

Condition: like new (used), Year of construction: 2019, operating hours: 10,000 h, functionality: fully functional, water tank capacity: 10,000 l, Complete mineral water and soft drink production plant for sale, available with brands, staff, or standalone. The production line features a mixed configuration, allowing both glass and PET bottle products to be manufactured on the same line. Nkodpfoxm Rmxox Ahveu The machine list is available in the documents along with information about the company. The machines have seen little use since 2019 and remain in good condition.

Year of construction: 2008, condition: good (used), Low Density Polyethylene (LDPE) Film Production Line Njdpfx Aoym Avyehveku High Capacity Blown Film (LDPE) Production Line, Comprising Of The Following Main Components, Extruder A - Bieloni: Screw Equipped With MSM Gravimetric Dosing Unit, Extruder B - Bieloni: Equipped With MSM Gravimetric Dosing Unit, Extruder C - Bieloni: Screw Equipped With MSM Gravimetric Dosing Unit. Blower Unit DOLCI, Ø400mm (Includes Spare Blower Ø600mm). Downstream & Auxiliary Equipment: Printing Unit, 4 Colours (3 Currently Installed), Corona Treatment Unit, Cooling Unit EURO CHILLER, 110kW (Year 2008). Technical Data (Approx.): Film Thickness: 75–200μm, Maximum Film Width: 6,000mm (Flat) Or 1,840mm (Folded). Maximum Printing Width: 1,600mm. Overall Dimensions: L18,500 × W11,500 × H13,000mm. Metal Supporting Frame: 4,700 × 4,700 × 11,000mm.

Condition: excellent (used), Year of construction: 2001, - Filter area: 2.5 m² - Year of manufacture: 2001 - Vacuum pump in DIN 1.4404 stainless steel - Including mixing tank with agitator - Equipped for residual filtration - Throughput (sludge): 450-500 l/h Dimensions: Nkodpfjym Avajx Ahvju - Depth: 1400 mm - Length: 2100 mm - Height: 1900 mm - Machine with very low operating hours - Machine in excellent condition

Condition: used, Year of construction: 2016, functionality: fully functional, Braukon 50hl brewhouse containing a Mash Ton, Lauter Ton and Wort Kettle in the main skid. Skid also contains Whirlpool and Chilled Liquor Tank also. Worth Kettle contains a vapour condenser (heat exchanger) that recovers heat from venting steam to prep the water for the next brew etc. (Returns 15HL hot liquor at 86°C per brew at 4% evaporation) Condenser is only 18-24 months old. Brewhouse is almost completely automated with the exception of hops and salts dosing (that need to be added through the hatches in the brewing vessels), and the cleaning of the Whirlpool (manipulation of hand valves, turning water supply / pump on/off on the control screen). Brewhouse was commissioned in 2015 Braukon have traveled to service it every year since we've had it, so would expect it to be in much better condition than other similarly aged brewhouses operated by small businesses. Brewhouse was completely CIP'd after every use. CIP System available also. Brewhouse is easily capable of doing 18 brews a week on 18/5, but was never worked even close to that potential. -Mash Kettle "Alloysius" Mash Hydrator Steam jackets and mash mixer (agi.) for temperature stepped mashing -Lauter Tun Maximum charge around 1100Kg malt Discharge via positive displacement "Seepex" pump -Wort Kettle 55hl maximum capacity Vapour Condenser – recovers heat from boiling as hot water returned to Hot Water Tank -Whirlpool Nkedpfoymyckjx Ahveu Brew length is 50hl i.e. you get about 5000L of wort (beer before it's been fermented) out of each brew. Will complete a brew every 4 hours Estimated 3000 to 3400 brews in it's total lifetime.

Condition: used, Production line consisting of: (1) Conical twin-screw extruder Technical details: Screw diameter 43 mm, capacity: max. 150 kg/h, KraussMaffei-Berstorff control system, weight 2.3 t /// Drive: SIEMENS 2860 / 30.5 rpm, 5,070 Nm, weight 1.2 t (1) Calibration table Nkedpfx Ajx I I Ncohvju Technical details: Equipped with three (3) SPECK pump systems, table length approx. 4 m (1) Haul-off unit Technical details: Speed approx. 0.1 - 11 m/min, pulling force approx. 25,000 N, contact length approx. 1,500 mm, profile clearance approx. WxH 300 x 180 mm, with film application unit (1) Sawing unit Technical details: Upstroke, saw blade diameter 250–400 mm, profile clearance WxH 340 x 20 mm / diameter 115 mm, cycle max. 40 cuts/min (1) Tilting table Technical details: Tilting of profiles, table length approx. 6,000 mm

Condition: used, Production line consisting of: (1) Twin-screw extruder Technical details: Screw diameter 65 mm, weight 2.8 t /// Drive: Thyssen Henschel TPM 3-65-DOS-25, serial number 6333547/13, weight 710 kg (1) Calibration table Technical details: Table length approx. 6 m (1) Haul-off unit Technical details: Nkedpfex I Itbjx Ahvju Contact length approx. 1,500 mm (1) Film application unit (1) Saw unit Technical details: Upward stroke, saw blade diameter 250–400 mm, profile gap WxH 340 x 20 mm / diameter 115 mm, sequence max. 40 cuts/min (1) Tilting table Technical details: Length approx. 6,000 mm

Condition: used, Line consisting of: (1) Twin-screw extruder Technical details: Screw diameter 75 mm, capacity: max. 200 kg/h, KraussMaffei-Berstorff control system, weight 3.5 t /// Drive: SIEMENS 2860 / 30.5 rpm, 5,070 Nm, weight 1.2 t (1) Calibration table Technical details: With three (3) SPECK pump systems, table length approx. 4 m (1) Haul-off unit Technical details: Speed 0.1–11 m/min, pulling force 25,000 N, contact length 1,500 mm, profile clearance WxH 300 x 180 mm (1) Punching device + guillotine unit Technical details: Punching force 1,800 N, design: C-frame, punching frequency 130 strokes/min, punching tool LxWxH 185x180x132 Nkedpfsx I Emfsx Ahveu (1) Tilting table Technical details: For pushing a single-strand roller shutter into an adjacent profile, table length approx. 6,000 mm

Condition: not inspected (used), Year of construction: 2018, functionality: unexamined, conveyor belt width: 50 mm, total length: 20,000 mm, total width: 5,000 mm, total height: 2,400 mm, controller model: SIEMENS SIMATIK, No minimum price – guaranteed sale to the highest bidder! Nsdpfxeyk Uv To Ahvsku Placing a bid obligates timely collection between 08/04/2026 and 16/04/2026! TECHNICAL DETAILS The line consists of the following components: Pressing units Riveting units Screwdriving units Various axles & motors Pneumatic accessories Conveyor belt (belt width: 50 mm) Vibratory feeders Grippers MACHINE DETAILS Control: SIEMENS SIMATIK Dimensions & Weight Dimensions (L x W x H): 20,000 x 5,000 x 2,400 mm Weight: 5,000 kg Note: The line can be transported on standard trucks.

Condition: like new (used), Year of construction: 2022, functionality: fully functional, overall weight: 4,000 kg, power: 17 kW (23.11 HP), total width: 1,510 mm, total length: 6,500 mm, total height: 1,820 mm, Automatic paper roll paper lid machine with inline packing machine for 8oz and 12oz cups Speed - 70~100 pc/minute Raw material - One-side or two side (polyethylene)film coated/laminated paper (Like the PE coated paper; PLA paper; card boad paper with film) Nkedpfjxur Hijx Ahvou Paper Lid Size - for 8oz and 12oz Working Power - 12kw Total Power - 17KW, Power Source - 3-phase, 380V, 50/60Hz, User Need To Buy Air Compressor

Condition: like new (used), Year of construction: 2019, operating hours: 200 h, functionality: fully functional, machine/vehicle number: N/A, Equipment: head guard, A robust capper for applying roll-on-pilfer-proof (ROPP) caps to bottles Capacity: 400-600 bottles per hour, depending on operator Benchtop operation 4 roller stainless steel capping head Heads can be changed on the machine to allow the application of different sizes of cap with the same machine Nksdpfx Ahox E S Nujvju Stainless steel frame and case Dual push-button safe operation

Year of construction: 2025, condition: excellent (used), 2025 Versafire EP 135 High End Professional Print Production Line Nsdjyml Sdjpfx Ahvjku Including: Versafire EP 135 A4/min Or 4,500 A3 Sheets/Hour (Simplex) Engine Unit, Media Identification Unit, Fuser Unit, Automatic Colour Diagnosis & Image Quality Monitor Unit, EFI Fiery Colour Controller E-86, EFI Impose (Streamlines & Automates The Imposition Process) & Fiery ES-3000 Spectrophotometer. Versafire Engine S/No. 5022F130003 (2025). LCIT RT5120 A3 Vacuum Feeder (A3 Large Capacity Tray With Vacuum Feeder, 2 Trays, Capacity Up To 4,400 Sheets (80 g/m2)). BY5020 Multi Bypass Unit (Additional Feeder (No Vacuum Support) For Up To 500 Sheets, Maximum 216 g/m2 Uncoated; e.g. For Banner, Special Stock, Envelopes, Overhead Transparencies, Labels, Letterhead & Postcards). LCIT Vacuum Feed Banner Sheet Tray (Vacuum Supported Banner Pile Feeder Option, Max. Capacity 730 Sheets (Top Tray Front Loading Will Be Disabled), Media Format 489-700mm Up To 300 g/m2). LCIT RT5120 Multi Bypass Attachment Kit For Vacuum Feeder (Must Be Installed When Attaching Multi Bypass Unit To Vacuum Feeder). Multi Bypass Banner Sheet Tray (Mechanical Support For Long Sheets (Banner). Roll-Away Cart Type 5010/5040 (Additional Roll-Away Cart For The High Capacity Stacker). SK5040 High Capacity Stacker (Receives & Holds Up To 5,000 Sheets, One Roll-Away Cart 5010 Comes Standard For Easy Removing Of Large Stacks Of Printed Material). Output Tray For Banner Sheet Type (Mechanical Support For Long Sheets (Banner). SR511 0 Standard Finisher (Up To 3,000 Sheets Capacity (80 gsm), Stapling Up To 100 Sheet With Automatic Shortening Of Staples). NOTE: A loading fee will be added to buyer's invoice of £200 + VAT. Description With TCRU/ORU (Sets A & B) Spare Parts To Increase Uptime; Includes Charging Unit, Drum Cleaning Unit, Image Transfer Belt Cleaning & Lubrication Unit, Infeed-, Transfer & Paper-Separation-Rollers, (4) Photoconductor Drum, Fuser Belt Smoothing Roller Unit, Dust Filter, Fuser Cleaning Unit, Fusing Unit And Fusing Refresh Roller Unit, Versafire EP Toner (Black), Versafire EP Toner (Yellow), Versafire EP Toner (Magenta), Versafire EP Toner (Cyan), (3) Waste Toner Bottles, Empty Toner Bottle Collection Box, Matt Fuser Assembly Unit, Dell Optical USB Mouse, Dell Qwerty USB Keyboard, Cables, Versafire EP Branding Kit & Operating Instruction Manuals. Please note: Printer is now in storage and not under power. NOTE: A loading fee will be added to buyer's invoice of £200 + VAT.

Year of construction: 1990, condition: ready for operation (used), A complete nonwoven fabric production line including peripheral equipment and a complete pre-blending line is available. 1) Pre-blending line with carding opener Houget Duesberg Bosson, year of construction: 1972, working width: 1500mm, drum: 1, worker-stripper pairs: 3, doffer: 1, feed rollers: 2, total line dimensions X/Y/Z: approx. 11000mm/1800mm/3100mm, operating hours: approx. 16414h, including feed table and bale opener. 2) Filling chute Spinnbau Bremen, year of construction: 1989, machine dimensions X/Y/Z: approx. 4000mm/2600mm/6250mm. 3) Weighing conveyor with vibrating chute Protec. 4) Card Hergeth, year of construction: 1990, working width: 2500mm, feed rollers: 2, feed roller diameter: 94mm, licker-in roller diameter: 413mm/550mm, worker-stripper roller diameter: 219mm/123mm, transfer roller diameter: 550mm, main cylinder diameter: 1500mm, doffer diameter: 850mm, compaction roller diameter: 260mm, pressure roller diameter: 2500mm. 5) Crosslapper Autefa Topliner CL 4000/4002 - WebMax, year of construction: 2006, min. fineness range: 0.7dtex, fiber types: chemical/natural/regenerated/blends, max. web weight: 100g/m², max. web weight with crosslapper: 5000g/m², max. laying width: 3500mm, working width: 2500mm, max. laying speed: 130m/min, lapper lift: 100mm, machine dimensions X/Y/Z: approx. 3850mm/8800mm/2200mm. 6) Drafting unit, working width: 2500mm, machine dimensions X/Y/Z: approx. 1600mm/3650mm/1650mm. 7) Double needle loom Dilo CBF 31/HVSL 31, year of construction: 2007, max. working width: 3100mm, stroke frequency: 1375/min, needle beam stroke: 60mm, horizontal beam stroke range: 0mm-6mm, number of needles per 1m working width: approx. 15430, machine dimensions X/Y/Z: approx. 3350mm/5150mm/4500mm, weight: approx. 38000kg. 8) Web accumulator Suchy WOB 3200, storage volume: 40m³, web weight range: 50g-2000g/m², max. working speed: 40m/min, max. production speed: 20m/min, working width range: 1000mm/3000mm, roller top width: 3200mm, machine dimensions X/Y/Z: approx. 4300mm/5050mm/5300mm. 9) Slitting unit Suchy, year of construction: 2006, weight: approx. 250kg. 10) Climbing roll winder, winding roller diameter: 350mm, min. winding diameter: 3inch, max. winding diameter: 1500mm. 11) Edge trimmer Hepp-Schwamborn. 12) X-ray measuring device Protagon Q6. This is a complete and automated nonwoven fabric production line starting from fiber bales. Documentation available. An on-site inspection is possible. Expected to be available from the end of March 2026. Nkedeymfc Ajpfx Ahvsu

Condition: used, Tenoning spindle 1 St. Number of milling agregates 4 St. Spindle diameter 50 mm # 2809 Weinig Unicontrol 6 ----- Technical Data Summary (Please inquire about any additional accessories included) Item 1: Cut-off saw ----- > Number of tools: 1 pc. > Spindle speed: 2,800 rpm > Spindle diameter: 40 mm > Maximum tool diameter: 400 mm > Motor power: 3.0 kW > Laser guide light for identifying the saw cut CNC-controlled length stop ----- > Length: 3,600 mm > Electronic length stop including positioned cut-off saw Item 2: Tenoning spindle ----- > Number of tools: 3 (stroke 2 x 100 mm) or 4 (Stroke 3 x 80 mm) > Tool clamping length: 320 mm > Pneumatic vertical spindle stroke: 240 mm for wood thicknesses 68 - 92 mm > Spindle speed: 3000 rpm > Maximum tool swing diameter: 320 mm > Spindle diameter: 50 mm > Maximum tool diameter: 360 mm > Motor power: 11 kW Item 3: 1. Profiling spindle (co-rotation and conventional) ----- > Position: vertical right > Number of tools: 1 pc. Nkedpsxtvgkofx Ahvsu > Tool clamping length: 120 mm > Spindle speed: 6000 rpm > Spindle diameter: 50 mm > Maximum tool swing diameter: 232 mm > Motor power: 7.5 kW Item 4: 2. Profiling spindle ----- > Position: Vertical right > Number of tools: 3 (stroke 2 x 100 mm) or 4 (stroke 3 x 80 mm) > Tool clamping length: 320 mm > Pneumatic vertical spindle stroke: 240 mm for wood thicknesses 68 - 92 mm > Spindle speed: 6000 rpm > Spindle diameter: 50 mm > Maximum tool swing diameter: 232 mm > Motor power: 11 kW 2 axially indexed feed rollers opposite the profiling spindle, for the production of narrow, short parts (e.g., glass-dividing muntins) Munch guide consisting of: Munch support strip from above in the area of ??the vertical right-han d profile milling unit and profiling spindle. Item 5: Horizontal top profile milling unit ----- > Clamping length: 40 mm > Spindle diameter: 40 mm > Motor power: 3.0 kW > Spindle speed: 5,850 rpm > Maximum tool swing diameter: 130 mm > Axial travel: 52 mm, indexed in 2 positions > Radial travel: 125 mm, indexed in 2 positions Item 6: 3rd profiling spindle (fitting spindle) ----- > Position: Vertical right > Tool clamping length: 160 mm > Axial travel: 90 mm, indexed in 3 positions > Radial travel: 100 mm, indexed in 2 positions > Spindle speed: 5,850 rpm > Spindle diameter: 40 mm > Maximum tool swing diameter: 210 mm > Motor power: 3.0 kW Further features ----- > Electric feed height adjustment including mechanical digital display and manual feed bar clamping > Rebating device for tear-out-free rebating > Double part package > Return conveyor for 1-person operation: swivel conveyor > Screen control > Angled window device > Electronic angle display for angled windows > Industrial PC with Windows PC control/NEXUS Extraction nozzle diameter: ----- Crosscut saw 80 mm Tenoning spindle 140 mm Profile spindle 1 140 mm Profile spindle 2 140 mm Grooving device from above 80 mm Hardware spindle 120 mm ----- Price of The above-men...

Condition: excellent (used), Year of construction: 2021, Year of manufacturing: 2021 Number of prints: approx. 6,8 millions Nedpernr Rzefx Ahvsku Condition: excellent Speed: 120 A4 / min. Max. format: 488 x 330 mm, long format up to 1200 mm (width 330 mm) Equipment: 4-colors (CMYK), 1x high capacity stacker, 2x high capacity input module with 4 drawers General description: Machine is in perfect condition and still producing. Printer was and still is under Xerox service contract. Only original Xerox service, spare parts a consumption materials were used. Test printing and inspection is possible.

Condition: repair required (used), Year of construction: 2000, functionality: limited functionality, machine/vehicle number: 200031, pressure: 6 bar, total width: 1,200 mm, total length: 3,500 mm, total height: 2,200 mm, overall weight: 1,500 kg, operating pressure: 6 bar, pressure (max.): 8 bar, empty load weight: 1,350 kg, input voltage: 400 V, number of previous owners: 1, pressure dew point: 3 °C, reception height: 1,000 mm, type of input current: three-phase, construction width: 1,200 mm, Equipment: CE marking, documentation/manual, type plate available, The GALDI RG250 is an automatic filling machine designed for the food industry, specifically for filling pre-formed cartons with milk, cream, juices, and other liquid or semi-liquid products. The machine transports cartons from the magazine to the erecting unit, where they are opened, shaped, and heat-sealed at the bottom. After precise volumetric filling, the carton is closed and transferred for further packaging steps. The RG250 is a well-established industrial model known for its robust stainless-steel construction and hygienic design. This unit is partially functional and suitable for refurbishment, retrofit projects, or as a source of spare parts. Key advantages: - Designed for filling carton containers in dairy and beverage production Nkodpfsx Eiwaox Ahvju - Hygienic, stainless-steel construction - Automated carton handling through erector and filling station - Precise filling volume control - Suitable for milk, cream, juices, and similar liquid products Ideal for: Dairy plants, beverage producers, and food-processing companies looking for a cost-efficient solution to upgrade or rebuild their filling and packaging line.