Used Edge Sanding Machine for sale (92,622)

Condition: used, Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, Dodpot Tqy Ejfx Aduoku quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Condition: excellent (used), Year of construction: 2003, Edgebanding machine Manufacturer: Bimatic Model: Starter plus 4.5 Dkodpfjw I Aqmsx Aduju Year of manufacture: 2003 Max. edge thickness: 0.4 - 3 mm Max. workpiece thickness: 48 mm End trimming unit: Yes Flush trimming unit: Yes Radius scraper: Yes Buffing unit: Yes

Condition: good (used), Year of construction: 1989, Machine with full equipment Length approx. 9 m Edge gluing Edge sawing Dkjdpjf Ua R Hofx Adusu Pre-milling Rounding milling Corner copying Pull scraper Buffing Corner copying

Condition: excellent (used), Year of construction: 2022, 0,4 - 5 mm Workingpiece thickness from to 10 - 45 mm Dkedpfsxfwdbox Aduju Feed speed 8 m/min.

Condition: as good as new (ex-display), Year of construction: 2023, 0,4 - 5 mm Workingpiece thickness from to 10 - 60 mm Dedpfx Aoxh Spkodusku Feed speed 12 m/min.

Condition: ready for operation (used), Year of construction: 2005, functionality: fully functional, machine/vehicle number: C-261-04-2523, feed rate X-axis: 9,000 m/min, saw blade diameter: 100 mm, rotational speed (max.): 12,000 rpm, Submitting a bid obliges you to collect the item by the deadline of 14.10.2025! TECHNICAL DETAILS Edge Processing Edge type: Straight edges Edge material: Cut-to-size strips, lip cuts, coil material Feed speed: 9 m/min Edge material thickness: 0.4–3.0 mm Lip thickness: 0.4–3.0 mm Edge material height: 55 mm Coil diameter: 800 mm Rotation speed: 12,000 rpm Dkedpfxoxhgk Ae Aduou Max. tool dimensions: 100 × 62 × 30 mm Extraction port Ø: 120 mm Workpiece Data Workpiece thickness: 8–50 mm Positioning accuracy: 0.1 mm Edge Banding Edge type: Straight edges Edge material: Coil material Max. tape cut: 3 × 30 mm or 0.8 × 45 mm Operating pressure: 6 bar Edge Glue Applicator Rotation speed: up to 1,800 rpm End Trimming Unit Motor speed: 12,000 rpm Saw blade diameter: 100 mm Cutting width: 2.6 mm Bore diameter: 32 mm Workpiece thickness: 45 mm Max. edge material height: 3 mm Edge material angle: 0–15° Edge material cross-section: 135 mm² Flush Trim Unit Rotation speed: 12,000 rpm Max. workpiece thickness: 8–50 mm Max. edge thickness: 3 mm Straight tools: 2 × WPL milling cutter Ø 50 × 12 × 16 mm, z = 4 Combination tools r = 3 mm: 2 × Trimmer Ø 56 × 50 × 12 × 16 mm, z = 4 MACHINE DETAILS Electrical Data Voltage: 400 V Frequency: 50 Hz Fuse protection: 16 A Control voltage: 24 V

Condition: used, Number of sanding units 4 St. sanding width 190 mm Sanding height max. 180 mm Control ja weight 3300 kg Dimensions (L/W/H) 2600x920x1890 mm Dust suction hood 2x180, 2x120 mm Double sided grinding machine Löwer DSM 2004 Double-sided four-band single-wood sanding machine for sanding Solid wood, e.g. Window wood etc. Highly stable top model with innovative details. Suitable for high Continuous load even at higher chip removal rates. - Successively arranged grinding units for rough grinding, fine grinding and finish sanding, each from above and below 1. Belt sanding unit with heavy steel roller 2. Belt sanding unit with rubberised roller and shoe 3.Finish aggregate with fiber brush - Direct driven wheels for slip-free power transmission - Maintenance and wear-free CERMET-coated sanding shoes with very good thermal conductivity and absolute dimensional accuracy - Foreign cooling of the grinding zones for a cooler grinding and higher Sanding belt life - positively driven pneumatically controlled grinding belt oscillation - effective sanding dust extraction directly on the sanding rollers - Dust extraction on the tension rollers - integrated brushing and finishing device with large sanding dust extraction - Motorized grinding thickness adjustment via precision threaded spindles and large dimensioned linear ball bearing sets on hardened and ground precision shafts with dust and dirt protection - Adjustment of chip removal below via precision threaded spindle with dimension display via scale ring (resolution 0,1mm) - Grinding belt tension via pneumatic cylinder with constant clamping pressure - Abrasive belt change with pneumatic belt release in seconds - Adjustment of the grinding belt when changing the belt - Electropneumatic compressed air monitoring - Overflow protection via contact roller for workpieces that are too thick - Workpiece transport via calibrated non-slip and adhesive conveyor belts over heavy, cast tables with finely planed surface and sprung Pinch rollers with fine adjustment - Cardan shaft drive for jerk-free and uniform workpiece transport - Feed gear motor with stepless speed 4-20 m / min - all motors are electrically protected - ergonomically arranged controls - digital strength display (resolution 0.1mm) with modern magnetic tape system Technical specifications: - Sanding belt speed 22 m / s - Sanding belt length 1800mm - Sanding belt width 200mm - Working width 190mm - Abrasive thickness 2-180mm - four brake motors for drive 5.5 kW - Feed motor 1.5 kW - Feed rate 4-20 m / min. - automatic height adjustment 0.37 kW - two brush sets with fiber brushes D 120 x 200mm à 0.37 kW - Exhaust nozzle 2 x 180mm 2 x 120mm - Extraction air speed 20 m / s - Pneumatic connection 6 bar - Working height 870mm - Length (with Softdisc 2740mm) 2600mm - Length with control panel (with Softdisc 3035mm) 2985mm - width 880mm - height 1910mm - Weight about 3300 kg - Operating voltage 400 volts, 50 Hz, 3P - CE version Equipped with the following options: - Sanding belt blow 4-band Djdpfx Adovu Hgbeujku via nozzles directly at the radii of the tensioning rollers within the extraction system arranged, separately switchable - Disc unit for defibering - two grinding disc discs with 200 mm diameter (maximum grinding width 180 mm) - adjustable laterally and in delivery - including frequency converter for stepless speed regulation instead ...

Year of construction: 2005, condition: excellent (used), chamfers PVC edges and others pneumatic pressure Dkedpfx Adjidmvneuju power supply 380V perfect condition

Condition: good (used), Year of construction: 2007, Used edge banding machine - Model KAL 310 - Year of manufacture 2007 - Including return conveyor - In good and fully operational condition Djdpfxjxhc Sis Adujku - Photos & video available

Condition: used, functionality: fully functional, Angle adjustable from 25° - 55° Sheet thickness up to 50 mm at 400 N/mm² Drive 4 kW Dsdpjxfh Taefx Adusku

Condition: new, Year of construction: 2023, 0,4 - 5 mm Workingpiece thickness from to 10 - 60 mm Feed speed 12 m/min. Dksdpfx Aoxh Spdjduou

Condition: used, Year of construction: 2018, Edge banding machine AKV 3006 DK - F with jointing milling unit including DIA - tools Jointing thickness up to 40 mm Workpiece thickness up to 3 mm Combined milling station radius R 2.5 mm Technical description With application of hot glue to the workpiece for edge material up to 3 mm Workpiece thickness 60 mm without jointing unit, 40 mm with jointing unit Maintenance-free, coated glue pot HF - cross-cut station (16,000 rpm) for front and rear edge overhang HF - milling station (16,000 rpm) with interchangeable cutter (combination version) and fine adjustment from the operator side Free slots for additional processing units (system Hebrock), feed approx. 10 m/min Cutting depth adjustment of the cross-cut saw Signal lamp for workpiece sequence, robust chain drive, ergonomically arranged control panel Double-roller top pressure beam Aggregate viewing window from machine rear and operator side PLC control including touchscreen Technical data: - Feed speed 10 m/min - Panel thickness 8 - 40 mm - Weight: depending on equipment approx. 1550 kg - Dimensions (L x W x H) 5250 x 1445 x 1600 mm 2-point pneumatic cutter adjustment 1 unit Switching between radius - flush/bevel for the combined milling stations, switching between bevel or flush is manual by flipping the stop flap in the machine Buffing station (polishing) 1 unit Corner rounding cutter 1 unit incl. combination tool and pneumatic bevel/radius adjustment, max workpiece thickness 40 mm Minimum workpiece length 300 mm Radius R 2.0 mm Radius scraper 1 unit incl. pneumatic lift device, radius R 2.0 mm Surface scraper 1 unit with pneumatic engagement control Glue station change system incl. 2nd glue pot and glue outlet downwards 1 unit for quick color change Grooving saw unit horizontal into the edge 1 unit incl. pneumatic lift device and grooving tool Separate extraction of jointing unit 1 unit directly attached to jointing unit vertically upwards d=80mm for optimal suction performance from AKV 3005 DK-F urgently recommended Dkedpfsxfh Tmex Aduou Ball bearing for corner rounding cutter 24.1mm 1 unit Ball bearing for corner rounding cutter 24.2mm 1 unit Interchangeable motor 0.37 kW for corner rounding cutter 1 unit with quick-change device incl. radius cutter R 1 Interchangeable spindles 1 set = 2 pieces 1 unit 1 set of quick-change motors for longitudinal processing top and bottom incl. tool R 1 Compressed air requirement: 100 - 150 l/hour. Storage location: Nattheim

Condition: excellent (used), Year of construction: 2010, operating hours: 2,560 h, functionality: fully functional, total length: 5,760 mm, workpiece height (max.): 60 mm, edge thickness (max.): 12 mm, height adjustment type: electric, plate height: 60 mm, Brandt 1650 Highflex with return conveyor and PU glue box, top condition Year of manufacture: 2010 Operating hours: 2,560 h Total edge length: 211,844 m Edgebanding thickness max: 12 mm Panel thickness max: 60 mm Coiled material thickness max: 3 mm Minimum workpiece width: 70 mm Feed speed max: 18 m/min Infinitely variable feed speed Motorized height adjustment Granulate glue system Premelting tank BRANDT QUICKMELT KD glue system 2 x PU glue tanks Strip magazine Joint milling aggregate End trimming unit with 2 motors Flush/radius/chamfer stations: 1 Corner copying unit with 2 motors Scraper unit Profile scraper, flat scraper Buffing station Dodpfx Ajvnwf Ujdusku Aggregates synchronized NC axis/axes Design: right-hand machine Machine length: 5,760 mm Conformity marking: CE mark Ligmatech Boomerang return system PU glue box The machine is still in operation; inspection encouraged; available by arrangement No warranty Collection only, forklift available Net price plus VAT Price negotiable

Condition: excellent (used), Belt sander Make Karnasch Type ALMI AL 100 Dodpjuf N Scofx Adueku with 6 different contact rollers or sanding rollers Diameter : 17,5 - 20 - 22 - 28 - 38 - 48 mm belt width 100 mm length 2000 mm Grinding range for grinding diameter 20 - 76 mm

Condition: excellent (used), Year of construction: 2022, Used edge banding machine - OLIMPIC K 360 R - Year of manufacture: 2022 - Available from November 2025 Dkedpfx Asxhc Evoduju - additional photos/video available

Condition: used, Manual folding machine with segments. CIDAN / Ulisch Theoretical bending length: 1350 mm; Some segments are missing, so currently a bending length of 1210 mm is possible if the upper tools are arranged closely together. The lower tools are complete. Maximum sheet thickness: 1 mm Pick-up location: 28755 Bremen _____ Our general terms and conditions apply, and the seller is not liable for typing or data transmission errors. The appearance of the items offered corresponds to their age and the images shown. The technical condition and wear of the items correspond to their age. Dkodpfswxgtzjx Aduju Used machines are sold exclusively to commercial customers and without warranty.

Condition: good (used), Year of construction: 2000, 0,4 - 12 mm mm Djdpfx Adjxd Dvzeuoku Workingpiece thickness from to 8 - 55 mm Total length 6.740 mm mm Feed speed 14 / 11 m/min. total power requirement 19 kw Weight 2.700 kg

Condition: excellent (used), Year of construction: 2005, Edge banding machine Brandt KDF 530 C equipped with jointing, corner copying unit, two scraping blades, and Riepe spraying systems. A video of the machine in operation can be sent upon request. The machine features a high level of automation: - Edge thickness approx. 0.4 – 8mm - Workpiece height approx. 10 – 50mm - Feed speed approx. 11 m/min - Noise-reducing hood - Extendable workpiece support - Extraction connection 1x200mm, 1x100mm, including the pictured piping - PC16 control system with color screen for user-friendly operation Units/aggregates: - Pressure beam: Manual adjustment with SIKO counter - Infeed fence: Manual adjustment with SIKO counter - Spray unit for release agent (Riepe) - Jointing milling with Leitz Whispercut diamond cutters, sharpened - Gluing unit switchable between synchronous and counter rotation - Pressure zone with 3 rollers - End trimming saw with two motors, straight or angled cuts (programmable adjustment) - Combination milling unit with motorized lateral adjustment - Radius scraper R2, pneumatically adjustable - Corner rounding unit R2 with diamond cutter, 1 motorized, pneumatic switching between thin and thick edges - Glue joint scraper, pneumatically retractable with large roller - Spray unit for cleaning agent (Riepe) - Buffing unit - Hood locking mechanism - CE mark - Operating instructions in folder and on CD All reversible blades on the milling units and scrapers have been renewed or rotated, saw blades and jointing cutters have been sharpened, and buffing wheels replaced. The machine is therefore immediately ready for operation. Only the diamond cutter for the contour milling has not been replaced but is still sharp. Minor paint damage has been touched up. Approx. 3,500 operating hours. The overall condition speaks for itself. Occasionally, the computer reboots during operation (mostly at high room temperatures); this has not been an issue for us, as operation can continue in the meantime. Dimensions approx. 4800 x 1200 x 1800 mm (L x W x H) Djdpfxexd Dudj Adueku Weight approx. 1,900 kg. The machine can be demonstrated at our premises by appointment. We only offer machines that are ready for demonstration in our warehouse; see "other offers from this supplier."

Condition: excellent (used), Year of construction: 2015, total length: 3,653 mm, Single-sided edge banding machine Manufacturer: Brandt Model: Ambition 1210 F, Optimat KDF 210 Year of manufacture: 2015 Feed speed: 11 m/min Workpiece thickness: 8 – 50 mm Minimum workpiece width: 70 mm Edge material (roll): 0.4 – 3 mm Edge material (strip): 0.4 – 3 mm Workpiece overhang: 38 mm Jointing unit: 2 x 2.2 kW Application unit: A3 End trimming unit, bevel/straight: 2 x 0.18 kW Milling unit: 2 x 0.27 kW (counter-rotating) Profile scraper with quick-change heads Dodpfxoxdxldo Aduoku Glue joint scraper Buffing unit: 2 motors Control system: EASYTOUCH Additional equipment Lubricant spraying unit for edge material

Condition: new, The new cylinder brush and sanding machine from Holzprofi Maker can be quickly and easily converted from a sanding machine to a brushing machine in just a few seconds. It is ideal for smaller workshops as it combines two machines in one. Advantages and Features: - Versatile options for surface finishing - Quick and easy changeover from sanding to brushing - Many different brushes available for a wide range of effects and processing possibilities - Infinitely variable feed rate and roller speed for perfect results - Workpiece width up to approx. 1100 mm - Precise adjustment of sanding height for consistent results Technical Data: Sanding width: 560 mm (1120 mm) Sanding height: 3 to 75 mm Roller diameter: Ø132 mm Table dimensions: 592x530 mm Extension table dimensions (2x): 582x245 mm Roller speed: 0 to 1800 rpm Feed speed: 0 to 7.5 m/min Extraction port diameter: 100 mm Main motor power: 1.5 kW Dksdpfx Adjwzzivoueu Feed motor power: 120 W Voltage: 230 V Dimensions: 1010x1060x1190 mm Weight: 155 kg Optional Accessories: Texturing brush for even and structured surfaces Abrasive flap brush for finishing and surface preparation tasks Steel wire brush for a used-look finish and pronounced grain effect

Condition: excellent (used), Year of construction: 1972, Bürkle long-belt sander with vacuum table and vacuum pump Table size approx. 2500 mm x 800 mm Dedsv Trlaspfx Adujku Manual height adjustment Without top belt cover Belt length 7200 mm Weight approx. 900 kg Dimensions approx. L x W x H approx. 3800 x 1700 x 1600 mm Location: Arrives at the end of April at warehouse 54634 Bitburg Sold as is - no warranty - no guarantee - freight prepaid -

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, PROFILATRICE COMAL PRD 12 Automatic edging machine for strip end processing. Used to prepare strip edges for subsequent roll forming. The machine is equipped with a set of rollers capable of performing cold roll forming of strips and sheets, which are continuously shaped until the desired profile or tube is achieved. Djdpfx Aexdr Swedujku The machine has seen very little use, is fully operational, and is in good overall condition. Manual and original documentation are available.

Condition: used, Year of construction: 2008, Used machine Dodpfx Asxdpm Seduoku Year of manufacture: 2008 Equipment and technical data: - Round pot glue application unit - Feed unit with automatic edge band magazine - Pressure zone with multiple pressure rollers - End trimming: 2 motorized saw units for crosscutting/end cap cuts - Top/bottom milling: 2 milling units with copy wheels for radius or chamfer - Radius scraper: pneumatically controlled, for post-processing of radii - Flat scraper: for smoothing the edge surfaces - Polishing unit: 2 polishing wheels with motors for final finish - Riepe spray system - Control: PLC with operator panel - Feed speed approx. 10–12 m/min - Workpiece thickness up to 52 mm - Edge thickness 0.3 – 12 mm - Power supply 3x 400 V AC, 50 Hz - Rated power 12.7 kW - Rated current 30.5 A - Control voltage 24 V DC - Max. fuse protection 35 A (5x 6 mm² connection cable) Machine dimensions: approx. 6120x840x1385 mm Machine weight: approx. 3,000 kg Availability: short-term Location: Bavaria

Condition: used, Storage location: Sonnefeld Dkjdpfx Adoway Dcjusu

Condition: like new (used), Year of construction: 2020, Hebrock drying box for edge banding machine Dsdpfxowqx Eme Aduoku Year 2020 Top condition - as new Location: ex stock 54634 Bitburg - immediately available -