Used Eccentric Press 1200 Ton for sale (20,441)

Year of construction: 1977, condition: ready for operation (used), An old eccentric press Elmerding with defective foot switch is available. Press capacity 30°: 25t, stroke adjustment range: 12mm-80mm, ram adjustment: 60mm, stroke rate: 120rpm, table adjustment: 150mm, safety distance: 144mm, weight: approx. 1450kg. Only 2-hand operation is possible. Documentation available. An on-site inspection is possible. Nksdpoypr Spjfx Ahvew

Condition: used, Single-column eccentric press RICHTER type PEKRS 80 Year of construction 1970 - overhaul 2024 Compressive force 80 ton. throat depth 350 mm Table size 900 x 650 mm Hole in the clamping table Ø 200 mm ram surface 700 x 500 mm Stroke rate 70 strokes/min. Stroke adjustment 6 - 100 mm ram adjustment 85 mm Installation height max. 400 Clamping pin bore Ø 50 mm Table height above floor 810 mm Motor power 8 kW Mains connection 400 Volt, 50 Hz - ORTLINGHAUS pneumatic clutch/brake combination - HERION XSz 32 press safety valve - Pneumatic ram compensation cylinder - Overload protection with breaker plate in ram - Central grease lubrication with hand pump Space requirement L x W x H 1800 x 1250 x 2830 mm Weight 5.7 tons Very good condition Technically overhauled and converted to the latest UVV with new electrics Control conversion in 05/2024 - suitable for manual insertion work - in accordance with DGUV Information 209-030 Press inspection and Machinery Directive 2006/42/EC Low Voltage Directive 2014/35/EU EN ISO 16092-1: Safety of machine tools - Presses - Part 1: General safety requirements EN ISO 16092-2: Machine tools - Safety of presses - Part 2: Mechanical presses - Control system with plain text error messages and diagnostic screen for rapid fault localization - New electrical cabinet, mounted on the side of the machine - completely based on SIEMENS, with PLC S7-1200 PROFIsafe and 7" TFT touch display - Two-hand control panel with emergency stop and engagement lock - el. foot switch - Cam switch unit with run monitor control Nksdpfoi Db Ibjx Ahvow - Stroke release via HERION XSz 32 press safety valve with pneumatic pressure compensator - New wiring of the machine - Updated operating instructions The machine is equipped with 6 operating modes: 1 = Set-up 2 = Single stroke two-handed 3 = Single stroke foot 4 = continuous run foot 5 = automatic continuous run 6 = reverse run

Condition: used, Single-column eccentric press EBU Type 75 SKU Machine no. No. P 4598462 Year of construction 1962 Compressive force 75 ton. throat depth 300 mm Table surface 800 x 620 mm waste hole 325 x 225 mm Plunger surface 470 x 180 mm Clamping pin bore Ø 40 mm Table height above floor 845 mm Stroke adjustment 16 - 140 mm Plunger adjustment 80 mm Installation height max. approx. 420 mm Stroke rate 60 + 105 strokes/min. Motor power 4 kW Mains connection 380 Volt, 50 Hz. - Pneumatic clutch/brake combination EBU - Overload protection with breaker plate in ram - UNIDOR tool monitoring system, type APS MINI - mechanically driven gripper feed with belt straightener OSTERKAMP, type ZPN 200/350 - strip width: 200 mm, feed length: max. 350 mm - Strip thickness: max. 3 mm or approx. 200 x 1.5 mm - 2 speeds due to 2 V-belt stages on the wheel transmission - Two-handed operation - Simple work area shielding for swinging open Nkjdpfx Ahodzqltjvsw - Table height adjustment in lowest position = threaded spindles for adjustment 50 mm below floor level - Control cabinet and control panel for tool monitoring adjacent - Automatic central lubrication - 4 machine feet Space requirement L x W x H 2600 x 2300 x 2450 mm Weight approx. 5.5 tons good condition

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Machine no. No. 122481 Year of construction 1984 Pressure capacity 100 ton. throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Nodpou Rwa Iofx Ahvskw Rear upright width 735 mm Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Motor power 11 kW Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter - Clamping pin bore with clamping piece - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Weight 8.3 tons Good condition

Condition: used, Single-column Eccentric Press MÜLLER GEFREES Type 60 SV DK (Identical to ExP60) Very lightly used eccentric press in original condition Machine No. 5250686 Year of manufacture: 1986 Nearly new condition Press force: 60 tons Throat depth: 280 mm Table surface: 740 x 560 mm Ram surface: 385 x 200 mm Through-hole in table: 300 x 200 mm Table surface (intermediate plate): 740 x 560 mm Through-hole in intermediate plate: Ø 103 mm Intermediate plate thickness: 70 mm Clamping pin bore: 40 mm Table height above floor: 815 mm (with intermediate plate) Installation height, max.: 275 mm (with intermediate plate) Installation height, max.: 345 mm (without intermediate plate) Stroke adjustment: 10–90 mm Ram adjustment: 60 mm Strokes per minute: 100 Motor power: 3 kW Drive: 380 Volt, 50 Hz - Mechanical rotary wedge clutch with pneumatic actuation - Spring-loaded single-jaw brake, controlled by cam disc - Stroke release via pneumatic footswitch - Overload protection with breaking plate in the ram - Table height adjustment via 2 threaded spindles - Manual central lubrication system by BEKA Schmiertechnik - Operating manual and pneumatic diagram included Space requirement (L x W x H): 1400 x 1100 x 2200 mm Weight: 3.4 tons In very good, almost new condition Nkjdpei A A Tbsfx Ahvow

Condition: used, Single-column eccentric press WEINGARTEN type E 40 Machine. No. 643/62 Year of construction 1963 Pressure capacity 40 ton. throat depth 250 mm Table opening 150 x 80 and Ø 200 mm Table surface 560 x 460 mm ram surface 250 x 200 mm Plunger stroke adjustable 8-88 mm Plunger adjustment 63 mm Installation height 320 mm Clamping pin bore Ø 40 mm Stroke rate 100/130 strokes / min. Motor power 2.2 / 3 kW Mains connection 400 Volt, 50 Hz Table height above floor 840 mm - Clutch/brake combination with WEINGARTEN friction threaded clutch with TDC run-through protection - Electric lift release via two-hand control Nedstx E Rqepfx Ahvjkw - Overload protection by breaker plate - Manual central grease lubrication - Front crankshaft support bearing - Control cabinet adjacent - UVV for manual insertion work Space requirement L x W x H 1800 x 1500 x 2200 mm Weight 3.1 tons

Condition: used, Single column eccentric press MÜLLER GEFREES type PDET 5 S/EK Machine No. Year of construction 1988 Nodoik Srwepfx Ahvjkw pressure force 5 ton. throat 125 mm head clearance 170 mm table area 280 x 220 mm waste hole Ø 90mm ram surface 160 x 100 mm stroke adjustment 4 to 40 mm ram adjustment 30 mm Installation height largest stroke top max. 210 mm Stroke rate 200 strokes/min. Clamping spigot bore Ø 25 mm Table height above floor 900 mm motor power 0,55 kW mains connection 380 volt, 50 Hz - pneumatic clutch-brake combination - electric foot switch - switch cabinet at the machine space requirement L x W x H 900 x 600 x 1700 mm weight 530 kg very good condition

Condition: used, Single-column toggle press MAY - MAYPRES - KOMATSU Type MKN 1-63/6 Eccentric toggle press, eccentric press Year of manufacture approx. 1984 Pressing force 60 tons Thrust 160 mm Nodpfev Uraaex Ahvskw Table size 580 x 360 mm Ram surface Ø 270 mm Clamping pin bore Ø 40 mm Distance between columns 218 mm Ram stroke 60 mm Ejector stroke 15 mm Ram adjustment travel 30 mm Max. installation height 300 mm (with intermediate table plate) Stroke rate 70 strokes per minute Motor speed 1400 rpm Motor power 3 kW Power supply 380 V, 50 Hz - Pneumatic clutch and mechanical brake with pneumatic release (separate clutch-brake combination) - Table intermediate plate L x W x H 580 x 360 x 58 mm, with holes and cutouts - Mechanical ejector, ejector device in the machine table, Ø 80 mm - Electric two-hand control and foot switch - Movable safety screen, UNIDOR protective housing with pneumatic front screen - BALLUFF cam switch Space requirement L x W x H 1400 x 1200 x 1850 mm Weight 3 tons Good condition

Condition: used, Single column eccentric press PELS - RICHTER type PEKR 125 Machine. No. 20684 Year of construction 1967 pressure force 125 ton. throat 430 mm table size 1100 x 750 mm ram area 890 x 650 mm table opening Ø 400 mm stroke adjustment 6 to 115 mm ram adjustment 100 mm installation height largest stroke top max. 450 mm Clamping spigot bore Ø 50 mm Stroke rate 60 strokes/min. Table height above floor 900 mm motor power 7,5 kW Mains connection 380 Volt, 50 Hz - Overload protection by crushing plate in ram - Compressed air clutch-brake combination DESCH - ram weight balancing cylinder - manual ram adjustment - two-hand operation - cam gear - Grease central lubrication Vögele - stroke counter Space requirement L x W x H 2300 x 1450 x 3030 mm weight approx. 10 ton. Nksdpfx Ahsfim Thevjw good condition

Condition: used, Single-column eccentric press WEINGARTEN type ER 63 Machine. No. 52A / 63 Year of construction 1963 Pressure capacity 63 ton. throat 280 mm Table surface 630 x 530 mm ram stroke adjustable 8-100 mm ram adjustment 63 mm Stroke rate 65 strokes / min. Motor power 4 kW Mains connection 380 Volt, 50 Hz - Clutch/brake combination with WEINGARTEN friction threaded clutch - Electric lift release via foot switch - Wheel reduction gear Nkjdpfx Aslb I Dzehvow - Overload protection by breaker plate - Front crankshaft support bearing Space requirement L x W x H 1500 x 1100 x 2500 mm Weight 4.5 tons good condition

Condition: used, Single column eccentric press WEINGARTEN type ERV 40 Machine No. 537 / 65 Year of construction 1965 Nkodoffm Hhspfx Ahvow Compressive force 40 ton. throat 230 mm table size 570 x 470 mm ram surface 250 x 200 mm clamping spigot bore Ø 40 mm installation height max. approx. 520 mm stroke adjustment 8 - 88 mm slide adjustment travel 63 mm Stroke rate 70 strokes per minute Drive power 3 kW Mains connection 380 Volt, 50 Hz - Table height adjustment - Overload protection by crushing plate - clutch-brake combination by WEINGARTEN friction thread clutch - electric 2-hand operation and foot switch - central lubrication via hand pump space requirement L x W x H 1600 x 1150 x 2300 mm weight approx. 2,6 ton.

Condition: used, Year of construction: 1976, pressure 400 t stroke 30 - 300 mm no. of strokes 55 /min throat 500 mm passage to the back 800 mm dayligth 950 mm table surface area 1580 x 1000 mm hole in the table 400 x 400 mm table height over floor 800 mm ram surface 1000 x 720 mm ram adjustment 125 mm Nkodoylzwtopfx Ahvjw power requirement 37,0 kW Weight 25,0 t dimensions (WxDxH) 2,5 x 3,1 x 5,1 m

Condition: used, Year of construction: 1961, pressure 063 t throat 270 mm Nksdpfx Aovuuc Rehvsw stroke 8 - 100 mm no. of strokes 115 /min distance table/ram, max. stroke up, adjustment up 415 mm table surface area 620 x 500 mm hole in the table 200 mm table height over floor 800 mm ram surface 305 x 260 mm ram adjustment 63 mm power requirement 7,5 kW weight 4,0 t dimensions (WxDxH) 1,3 x 1,7 x 2,35 m SPECIAL DEAL as is where is, WITHOUT additional work free loaded to truck

Condition: used, Year of construction: 1995, Pressure 250 t throat 450 mm stroke 8 - 135 mm no. of strokes 50 /min distance table/ram, max. stroke up, adjustment up 635 mm Nodpsvuk Hxefx Ahvjkw table surface area 1250 x 850 mm hole in the table 355 mm table height over floor 950 mm passage to the back 660 mm ram surface 790 x 610 mm ram adjustment 130 mm power requirement 18,5 kW weight 14,0 t Dimensions (WxDxH) 1,5 x 2,8 x 3,65 m with motor, pneumatic clutch/brake combination (Ortlinghaus), mechanical overload protection in ram, manual stroke adjustment, manual ram adjustment, pneumatic counterbalance in ram, fix table, motoric centralized lubrication, two-hand operation

Condition: used, Year of construction: 1989, Pressure 080 t throat 300 mm stroke 8 - 140 mm Nedpovuuavjfx Ahvokw no. of strokes 60 / 90 /min distance table/ram, max. stroke up, adjustment up 420 mm table surface area 800 x 600 mm hole in the table 330 x 230 mm table adjustable 230 mm table height over floor 750 - 980 mm ram surface 600 x 240 mm ram adjustment 100 mm power capacity 4,5 / 6,9 kW Weight 5,5 t Dimensions (WxDxH) 1,4 x 2,5 x 2,6 m permitted for manual put-in according to the German Safety Regulations (UVV) with motor with 2 speeds, hydraulic clutch/brake combination, hydraulic overload protection in ram, manual stroke adjustment, manual ram adjustment, adjustable table, manual central lubrication, two-hand and foot operation press can be inspected in running condition in our warehouse

Condition: used, Year of construction: 1977, pressure 250 t stroke 40 - 190 mm no. of strokes 40 /min throat 500 mm passage to the back 1050 mm dayligth 615 mm table surface area 1380 x 880 mm hole in the table 450 mm table height over floor 800 mm ram surface 1200 x 800 mm ram adjustment 125 mm power requirement 22,0 kW Weight 24,0 t dimensions of the machine ca. 2,0 x 2,5 x 3,95 m x m x m permitted for manual loading according to the German Safety Regulations (UVV) with motor, pneumatic clutch/brake combination, hydraulic overload protection in ram, pneumatic counterbalance in ram, motoric ram adjustment, manual stroke adjustment, motoric centralized lubrication, bolster plate, two-hand operation Nedpfxevuuaio Ahvokw

Condition: used, Year of construction: 1957, pressure 100 t throat 315 mm stroke 30 - 160 mm no. of strokes 40 /min distance table/ram, max. stroke up, adjustment up 460 mm table surface area 910 x 680 mm Nodpfx Aovzxnwshvjkw Hole in the table 400 mm table height over floor 800 mm passage to the back 400 mm ram surface 630 x 400 mm ram adjustment 80 mm power requirement 7,5 kW weight 7,5 t dimensions (WxDxH) 1,7 x 2,0 x 3,0 m SPECIAL DEAL as is where is WITHOUT putting into operation / WITHOUT additional work free loaded to truck

Condition: used, Year of construction: 2000, pressure 075 t throat 295 mm stroke 16 - 140 mm Stroke rate 75 / min Distance table/ram, max. stroke up, adjustment up 450 mm Table surface area 800 x 595 mm Hole in the table 330 x 230 mm Table height above floor 745 mm Ram surface 470 x 180 mm Ram adjustment 80 mm Power capacity 5,5 kW Weight 5,0 t Dimensions (WxDxH) 1,5 x 2,5 x 2,5 m overhauled by the manufacturer in 2000 with motor, pneumatic clutch, mechanical overload protection in ram, manual stroke adjustment, manual ram adjustment, fix table, motorized central lubrication, two-hand and foot operation Nedpfx Ahovut Hhevskw as is where is, WITHOUT any additional work, free loaded to truck

Condition: used, Year of construction: 1995, pressure 063 t throat 260 mm stroke 12 - 120 mm Stroke rate 30 - 130 / min Distance table/ram, max. stroke up, adjustment up 495 mm Table surface area 800 x 560 mm Hole in the table 220 mm table height over floor 800 mm Passage to the back 270 mm Ram surface 450 x 360 mm Ram adjustment 120 mm Power capacity 5,5 kW Weight 5,0 t Njdpjvut Ewefx Ahvjkw Dimensions (WxDxH) 1,8 x 1,5 x 2,7 m only permitted for automatic mode according to the CE Regulations with infinitely variable drive, pneumatic clutch/brake combination, mechanical overload protection in ram, fix table, two-hand operation can be inspected in running condition in our warehouse

Condition: as good as new (ex-display), Year of construction: 2022, operating hours: 100 h, functionality: fully functional, machine/vehicle number: TYPE 63 R4, overall weight: 4,600 kg, pressing force: 63 t, type of input current: three-phase, power: 5.5 kW (7.48 HP), input voltage: 400 V, Equipment: documentation/manual, EECCENTRIC PRESS OMERA Model: 63 R4 Basic Technical Data Nominal force: 630 kN Motor power: 5.5 kW Strokes per minute: 45–104 Slide stroke: 9–120 mm Clearance between table and ram: 310 mm Table dimensions: 750 × 570 mm Ram dimensions: 500 × 350 mm Table thickness: 65 mm Table opening: 165 mm Machine weight (approx.): 4,600 kg Machine dimensions (for transport): 2806 × 1244 × 1492 mm Power supply: 380 V / 50 Hz / 3 Ph Machine color: RAL 7035 (light grey) / moving parts RAL 5017 (blue) Machine Equipment Centralized lubrication system PLC: SCHNEIDER with control panel Inverter for adjustable press speed Pneumatic clutch Balancing cylinders Hydraulic overload protection system Nkjdpfx Aoyn Sdpohvew VPN connection for remote access Additional Equipment Additional work plate 750 × 570 × 65 mm (1 pc) Vibration dampers (1 set) Work area lighting (1 set) Tool protection and press operation monitoring system Machine Details Serial number: CM18355 Year of manufacture: 2022 Operating hours: approx. 100 Condition: Machine used only for demonstration and tool testing Documentation Complete documentation in Croatian language (printed and digital) Electrical and hydraulic diagrams CE Declaration of Conformity Disassembly, preparation, and loading for transport: approx. 1,500 EUR

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, overall weight: 2,900 kg, input voltage: 400 V, power: 4 kW (5.44 HP), type of input current: three-phase, Eccentric press PRESSIX 40T Model 40CNV4 Serial No 40/2/88/03 MAchine weight _ 2900 kg Inverter for speed change. Variable speed 60/180 rpm High number of strokes per minute Slider with 4 bronze guides Automatic and centralized lubrication Hydraulic release Pneumatic clutch-brake group Adjustable stroke length using a toothed ring Balancing cylinders Nsdpfx Ajyn Rhyohvskw Slider adjustment mm 70 Closing height mm 240 Table surface mm 480 x 650x53 Table opening mm 120 Slider surface mm 300 x 370 Hole in the slider mm 50 Power kW 4 User manual and electrical installation in English. Machine in excellent condition. Used for small batches of automatic production. Total: 6,500,000 strokes Programs: tool adjustment, semi-automatic work, auto, automatic work, two-handed work, work with a pedal, turning the mortar in the opposite direction Dismantling and loading are charged additionally

Year of construction: 1990, condition: used, Hbret press with 120-ton pressing force, currently disconnected and drained, ready for transport Nkedpfx Aeyctnxshvjw

Condition: good (used), functionality: fully functional, tested machine : Power 75 tons Stroke rate 90 strokes throat depth 300 mm ram stroke 16 - 140 mm ram adjustment 80 mm with shield , . Njdpjynztgefx Ahvjkw new UVV-tested .

Condition: used, Year of construction: 1979, Pressure 063 t throat 400 mm stroke 16 - 90 mm no. of strokes 60 /min distance table/ram, max. stroke up, adjustment up 350 mm table surface area 1000 x 750 mm hole in the table 260 x 140 mm table height over floor 710 mm ram surface 600 x 220 mm Nkodpoylck Uefx Ahvow ram adjustment 50 mm weight 4,3 t dimensions (WxDxH) 1,1 x 2,6 x 2,4 m SPECIAL DEAL as is where is WITHOUT putting into operation / WITHOUT additional work free loaded to truck

Condition: used, Year of construction: 1986, total height: 2,900 mm, total width: 1,450 mm, total length: 1,500 mm, Empty weight: 5.500 kg Price: On request - Year: 1986 - Documentation available: Yes - CE certificate present: No - Serial number: 88 09-86 - Drive system: Conventional - Press force [ton]: 63 - Min. stroke [mm]: 10 Nksdpfeylb Edex Ahvow - Max. stroke [mm]: 100 - Table length [mm]: 710 - Table width [mm]: 480 - Ram width [mm]: 320 - Height adjustment [mm]: 80 - Transport dimensions: 1500mm x 1450mm x 2900mm (l x w x h) - Transport weight [kg]: 5500kg - Transport packages [pcs.]: 3 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum