Used Coating Machines for sale (65,192)

Condition: good (used), Year of construction: 1999, Built in 1999 400 V; 50Hz Fsdpfxeba Hz Ue Ab Tegk 1.5 kW Linishing belt 100 x 1500 Belt speed 25m / sec. Weight approx. 50 kg

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: Fodpjwzl Hxsfx Ab Tsgk * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: used, Year of construction: 2016, functionality: fully functional, machine/vehicle number: 430/16, Powder Coating Line (Pass-through Polymerization Oven for Powder Paint, complete with Conveyor System and Dual Paint Booth) Basic technical data of the oven: - Max. external dimensions (L x W x H): 9.6 m x 6.6 m x 2.5 m - Weight: approx. 9,000 kg - Max. operating temperature: 220°C - Max. burner power / GZ50/: 2 x 160 kW - Fan motor power: 24 kW - Power supply: 3 x 400 V +N +PE, 50Hz Maximum workpiece dimensions: - L = 2.0 m - H = 1.0 m - W = 0.6 m Included with the machine: Fgjdpfx Aou Hib Njb Tok Complete technical documentation + parts lists. The oven is integrated with an overhead conveyor system by JOKŚ. The conveyor system includes 42 m of tracks, along with a drive system and lubrication system; control system with speed regulation in the range of 0.5–1.5 m/min. APAR AR200 speed recorder, LG iG5A series inverter, EATON MFD-AC-CP4 manual power/communication module, MFD-CP4, MFD-80. Manual powder coating booth; pass-through, two-station. Paint access windows on opposite sides, offset. Max. dimension of painted workpiece: - L = 2.0 m - H = 1.0 m - W = 0.6 m A linear overhead transport system runs through the center of the booth. The booth includes 3 tanks adapted for powder recovery/color change, filtration system based on cartridge filters. End tanks equipped with screens.

Condition: excellent (used), Dust extractor unit to run with preduster. Almost as new. Fgedpfx Aboumm Npe Tjk

Condition: like new (used), Year of construction: 2023, For sale: MHM SPiQ 20 45×55 screen printing carousel (SYNCHROPRINT iQ OVAL compact) with iDS (individual Drive System). Manufacturing date: January 2023. Manufacturer: MHM – Machines Highest Mechatronic GmbH (Austria) Model: SPiQ 20 45×55 Type: 1450IQ Year of manufacture: 01/2023 Power supply: 3×400 V, 50/60 Hz Connected load: 7.4 kVA Fedexb Avzopfx Ab Tsgk Air requirement: approx. 690 l/min, 0.8 MPa (8 bar / 116 psi) Specification (per order): • Print area: 45×55 cm • Number of printing stations: 13 • Number of flash cure units: 4 Equipment: • 20× aluminium palette with neck cut-out: 52×80 cm • 13× squeegee blade 50 cm / 65 shore • 13× flood blade (low) 50 cm • 1× MHM Pro Iron – 40 cm Overall dimensions: 3.5 m × 11 m

Year of construction: 2013, condition: excellent (used), machine/vehicle number: 181941, Air Delivery System: Re-circulating Temperature range: +/- 8°C from ambient within a programmable range of 19 – 30°C Temperature control: +/- 0.5°C Cooling Capacity: 2000W Temperature Sensor: shared output from integrated printer sensor (0 – 10V input over 0 – 50°C) Air In Filter: G4 (91% Average Arrestance) EN 779: 2002 Refrigerant Gas: R134a 0.75Kg Full load current: 12.6A Start Up Current: 20A Frequency: 50 / 60Hz Voltage: 230V +/- 10% (207V – 253V working range) Single Phase Acoustic Noise: > 75dB Dimensions: 1300mm High (+ beacon), 510mm, 540mm Condensate: Collected in 5 litre container for disposal or piped to drain Weight: 100Kg Documentation not included Fsdohg Rcxopfx Ab Tsgk the TCM is a precision temperature control module designed to enhance the Print Process by providing a highly stable and accurately controlled air temperature within DEK's range of printers. The operating range of the TCM offers wide control of the process s temperature either side of factory ambient. As applications become more varied the requirement to produce high yield results can be aided by the ability to heat as well as cool from factory ambient. Adhesive printing for example benefits from a temperature in the 25-30°C range, which is generally higher than conditioned factory ambient. Conditioned air is fed from the TCM into the print area and returned via ducting located beneath the printer. Ducting design has been formed to achieve minimal airflow rates over the process area prolonging tack performance of solder pastes and increasing stencil life. Due to its optimised design and re-circulating system the TCM is energy efficient and requires minimal input power from a single-phase mains supply. Exhaust air is vented through the top of the TCM alleviating the need for any connection to factory extraction systems. The TCM will automatically shut down following a predetermined delay if the printer is powered down or covers are left open. To monitor process temperature the TCM utilises the output from the printers integrated Temperature Sensor located on the print carriage resulting in accurate feedback and control. To prevent process contamination conditioned air is passed through a filter before entering the printer. The possibility of process contamination is further reduced due to the TCM maintaining a higher air pressure within the printer compared to the surrounding environment thus limiting the ingress of airborne particulates. The Modules operating status is indicated by provision of a 'four colour' beacon clearly visible to line operators. Any condensate produced can be gravity piped to drain or collected in an easy to empty 5-litre container. Two sensors monitor condensate level and give a warning via the beacon when container requires emptying. The TCM will automatically shut down if the container is not emptied to prevent overflow. Sales price: 1900 Euro + VAT, negotiable, FCA Oradea, Romania Irrtum, Anderungen und Zwischenverkauf vorbehalten /

Condition: new, Year of construction: 2025, operating hours: 1 h, functionality: fully functional, travel distance X-axis: 4,000 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 1,000 mm, rotational speed (max.): 8,000 rpm, controller manufacturer: STYLE CNC Machines, number of slots in tool magazine: 24, motor manufacturer: FANUC, Delivery after consultation Ref: 24F048 Year of construction: 2025 Condition: Showroom Specifications: Fgodpfxsw Ty S So Ab Tek - X-axis: 4000 mm - Y-axis: 1000 mm - Z-axis: 1000 mm - 26 kW (S6) main motor - 8000 rpm - BT-40 - Automatic tool changer (24 positions) - Remote service (IXON) + network connection - Stronger coolant pump incl. spray gun - Upgraded to the latest STYLE software available

Condition: new, Year of construction: 2024, functionality: fully functional, machine/vehicle number: PEF-2.5 PULVER EINBRENNOFEN ELEKTRISCH, temperature: 230 °C, heating capacity: 30 kW (40.79 HP), inner dimension length: 2,500 mm, inner dimension width: 1,505 mm, ✈️ Plus shipping costs – Shipping available upon request.✈️ Fast delivery: Only 6 weeks after receipt of payment! ✅✅✅Energy Class A+++✅✅✅ ✅ Plug & Play system – Delivered fully assembled, ready to use immediately! ✳️ Maintain your liquidity! We offer a variety of financing options to ensure your investment has the best chance of success. Contact us today to learn more about our hire purchase, warranty, or leasing programs. ☘️Environmentally friendly☘️⚡️Green energy⚡️☘️ ⭐ Powder furnace with electric heating - ✔️ Internal dimensions: 2500 mm L * 1505 mm W * 1800 mm H ✔️ Electric heating output: 30 kW/h ✔️ Fan: 3000 m3/h 80 mm SS ✔️ Circulation fan output: 1.5 kW/h ✔️ Total 35 kW/h +- 10% ✔️ Digital heat control, continuously adjustable temperature up to 220°C ✔️ Sandwich panels inside: 1.5 mm galvanized steel, outside: 1.5 mm powder-coated Steel ✔️ Adjustable curing temperature, curing time, and exhaust fan function ✔️ An audible signal sounds at the end of the curing time ✔️ Insulated door with special locking systems (snap lock) ✔️ Insulation: 150 mm (150 mm rock wool) 🔥 PEF-2.5 Curing Oven: Your versatile industrial oven for drying and curing processes! 🔥 Whether powder coating, wet paint, plastic processing, or other thermal processes – the powder curing oven is your reliable solution for professional curing and drying processes up to 230°C! 🌡️ _____ 🚚 Maximum loading flexibility • Compatible with ceiling rail systems • Optionally with insert shelf system for small batches _____ Fodpfx Ajwfgbrsb Tsgk ⚙️ Intelligent control – just the way you need it ✅ PID control (optional) for precise temperature control ✅ Touchscreen control panel & smartphone control 📱 (optional) ✅ Weekly & monthly reports at the touch of a button (optional) ✅ Timer function: freely programmable from 10 minutes to 24 hours ⏲️ ✅ Automatic shutdown after the end of the process _____ ♨️ Ramp heating mode (optional) Precisely control temperature progression and holding times, e.g. E.g.: • Reach target temperature within a defined time • Maintain desired time • Controlled cooling to target temperature • Automatic notifications of process events _____ 🛡️ Safety is our priority 🟢 Safety sensors to prevent overheating 🟢 Automatic shutdown in the event of a fault 🟢 Acoustic warning signals in the event of errors 🟢 Solvent and fume removal via automatic venting _____ ⚡ Customized energy and heating system 🔥 Also available with an extension up to 400°C for high-temperature processes (optional) _____ 🧠 No repeated settings necessary! The furnace saves your process parameters – batch by batch. This saves you time and avoids errors. _____ 📢 And best of all: If you have special requirements – we also build customized furnaces according to your specifications! Contact our team of experts for a personalized consultation! _____ ☀️ 2-YEAR WARRANTY ☀️ Request more information

Year of construction: 1990, condition: ready for operation (used), Working width: 900mm, length: 2600mm, width: 2600mm, height: 2000mm, weight: 1.8t, operating hours: 5866h. Including wet suction. Documentation and maintenance reports available. On-site inspection is possible. Fgsdpfx Abouzlg Ds Tsk

Condition: good (used), Tray wash machine, direct from recently closed ‘meat-free’ factory. In lovely condition. Fgsdpfx Aerfdq Usb Tsk

Condition: new, Year of construction: 2019, Storage tanks, e.g. for bitumen for asphalt mixing plant(s), etc. (vertical design) 7 x 70 m³ 1 x 68 m³ with agitator New, unused, from project cancellation, thermal oil heated and electric heating possible, complete, immediately available, for sale (individually or as a complete package). Fedpjw Nwtljfx Ab Togk

Condition: like new (used), functionality: fully functional, fuel type: diesel, color: blue, first registration: 03/2020, emission class: euro6, Year of construction: 2020, operating hours: 3,100 h, I sell a trailer for the production of cement screeds and polystyrene concrete by GB-Machines Mobileman D5 ZE. Year of production 3.2020. the condition of the machine very good. Everything in working order. Full automation of component weighing, automatic dispenser of chemicals and reinforcement. Equipped with high-pressure washer, water hoses, trestle. The capacity of the cement tank 8m3, sand / polystyrene tank 22m3. Full control of functions by remote control. Hatz 4H50TIC 4-cylinder engine Fgsdotn Nl Ujpfx Ab Tjk Estrichauflieger Mobileman D5 ZE 30 m³ Mulde, Sand - Styroporkammer 22 m³ und Zement-Kammer 8 m³, EZ 03/2020, 3-Achs Auflieger, Luftfederung, BPW-Achsen, 1.Achse liftbar, 3.Achse lenkbar, Bereifung 385/65/22,5 auf Alufelgen: 1.Achse ca. 12 mm, 2.Achse ca. 12 mm, 3.Achse ca. 14 mm, Fahrgestell der Fa. Kempf SKM/3/S/39A13, kippbar, techn. zul. GG 39.000 kg, zul. GG 36.000 kg.

Condition: like new (used), Year of construction: 2019, operating hours: 1 h, functionality: fully functional, machine/vehicle number: 2196028, Gerätetyp: Vollautomat Betriebsart: elektrisch Material: Edelstahl Produktkennzeichnungen: Hersteller-Art.-Nr: VA 4000/AT Gewichtsinfo: Gewicht: 130 kg Geräteanschluss: Fsdpfjv Acm Tex Ab Tsgk Anschlusswert: 600 Watt Netzspannung: 400 Volt Schnittstärke maximal: 10 mm Messergröße: 330 mm Länge (Breite): 1270 mm Tiefe: 853 mm Höhe: 1330 mm

Condition: new, Year of construction: 2025, total height: 4,000 mm, total length: 7,000 mm, total width: 3,000 mm, warranty duration: 24 months, temperature: 80 °C, air demand: 36,000 m³/h, input voltage: 380 V, heating capacity: 345 kW (469.07 HP), power: 40 kW (54.38 HP), fuel: liquid petroleum gas (LPG), energy consumption: 40 kWh, insulation material: Mineralwolle, insulation thickness: 50 mm, nominal power: 345 kW (469.07 HP), Equipment: lighting, Pony 7000 Sales Price List Paint booth 7 x 4 x 3 meters • Reinforced partial grating 5 mm • Height 3 meters (Sprinter height) • 2 x 7.5 kW motors (belt drive) • ATEX ceiling lighting • 24,000 m³/h • Incl. 2 drive-on ramps for above-floor version • Above-floor and in-ground version at same base price Base price: €28,900 Base price for 2.76 meter height version minus €1,000 (passenger car height) Base price for 3.5 meter height version plus €1,000 (motorhome height) Door-in-door system: €1,800 Double glazed doors: €1,800 11 kW motor incl. larger fans and enhanced control cabinet with direct drive: €7,770 15 kW motor incl. larger fans and enhanced control cabinet with direct drive: €8,610 Side lighting: €2,870 Fgedpfx Abowzmcbe Tok Ceiling lighting EX protection according to ATEX: €1,470 Full light-duty grating: €1,785 Full heavy-duty grating, reinforced 5 mm: €2,990 Direct drive with PLC control for 11 kW motors (incl. soft start): €15,120 Direct drive with PLC control for 15 kW motors (incl. soft start): €17,640 Soft start for 7.5 kW motor (belt drive only): €1,239 PLC control for 7.5 kW 24k m³/h motors with 3-stage energy saving program: €5,670 PLC control for 11 kW 30k m³/h motors with 3-stage energy saving program: €7,770 PLC control for 15 kW 30k m³/h motors with 3-stage energy saving program: €8,610 PLC control for 2 x 5.5 kW 36k m³/h (belt drive) motors with 3-stage energy saving program: €5,565 Pneumatic drive-on ramp: €4,900 Grating modification for lift: €1,785 Pass-through system with double gates (without door-in-door): €3,250 Tri Axis ramp: €7,980 Second service door (position freely selectable): €1,150 Info: 11 kW motor set at 1,200 rpm (inverter) (1,000 rpm motor) achieves 36,000 m³/h

Condition: used, Year of construction: 2007, Overview  This sleeve labeling machine was manufactured in 2007 by the Italian company CLEVER Machines. The machine is in very good condition, has been regularly serviced with original spare parts, and is currently dismantled and stored in a dry warehouse. It comes with an integrated shrink tunnel. Technical data  Capacity: 18,000 bottles per hour Label positions: Full bottle sleeve or partial bottom sleeve Additional components: Shrink tunnel CLEVER Machines STJ 3 Scope of Delivery  CLEVER Machines GS 4001 sleeving unit Shrink tunnel CLEVER Machines STJ 3 Fsdpfswhkhhox Ab Togk

Condition: excellent (used), Washing machine which can wash a tote bin and its lid at the same time. Excellent condition. Fgsdov Ihgvepfx Ab Tsk

Condition: new, Year of construction: 2025, machine/vehicle number: SÇ 211 Alüminyum Pvc Orta Kayıt Alıştırma Makinesi ( 2 Bıçak), - Conforms to CE standards. - Possibility of lapping the middle register connections of PVC and aluminum profiles. - Up to 30 degrees at different angles, possibility of lapping the middle register connections of profiles - Pneumatic profile clamping system B7ull38nwa - Ability to move the milling motor with a pneumatic cylinder. - Easy series change thanks to the separator button (60-70) OPTION - Hydro check system Fgedpjq U S Ahofx Ab Tok - Cooling System

Condition: new, Year of construction: 2024, functionality: fully functional, ⚡️ Top Service ⚡️ Fast Delivery ⚡️ Great Support! ✈️ Price includes shipping within Germany – No additional shipping costs! ✈️ Fast delivery: Only 6 weeks after receipt of payment! Fgsdpowfhu Hofx Ab Tek PROFESSIONAL POWDER COATING HAS NEVER BEEN SO EASY! Want to expand your business and enter the world of professional powder coating? PEF2.5+ is the perfect solution for beginners! This powerful system enables efficient, cost-effective, and high-quality coating of car rims and smaller workpieces – with minimal effort! ✨THE UNBEATABLE OFFER – ONLY UNTIL THE END OF MAY!✨ Instead of €38,500, now for only €31,900 PLUS VAT. Take advantage of this limited-time offer before it's too late! PONY Luxury Coating – IMPRESSIVE QUALITY! ✅ Plug & Play system – Delivered fully assembled, ready to use! ✅ 100% European manufacturing – Not made in China, but the highest quality according to European standards! ✅ Modular & expandable – Additional options for greater performance and flexibility! ✅ All spare parts included – Long-term use with no hidden additional costs! ✳️Maintain your liquidity! We offer a variety of financing options to ensure your investment has the best chance of success. Contact us today. ✳️ ✨✨Buy directly from the manufacturer and secure the price and quality advantage!✨✨ ☘️Environmentally friendly☘️⚡️Green energy⚡️☘️ Powder furnace + powder booth + powder gun Complete starter kit PEF2.5+ ⭐ Powder furnace with electric heating ✔️WIDTH (INTERNAL): 1,505mm ✔️HEIGHT: 1,800mm (from the air duct) ✔️LENGTH (INTERNAL): 2,500mm ✔️The thermoblock unit measures 785x1800x2210mm, the heating output is 30 kW/h, and a circulation fan is included. 1.5 kW/h-1 pc., one exhaust fan is 0.54 kW/h. ✔️ Double-leaf door with thermal insulation and silicone seal. ✔️ Guide rails for trolleys are manufactured in the dimensions indicated on the floor panels. ✔️ Specially designed air duct ensures even air distribution in the curing oven. ✔️ The electrical switchgear is made of Siemens and Schineider. This curing oven does not have a PLC system. PLC is available as an option. ✔️ Curing temperature, curing time, and heating unit function are adjustable. At the end of the program, an audible and light signal sounds from the buzzer. ✔️ Additionally, a product transport trolley with cast wheels is located inside the oven. ⭐ Powder Booth ✔️DIMENSIONS: 800x1930x2200mm (dimensions including fan) ✔️ Teflon filters: 4 pcs. ➢ Filter extractor fans: 4kW x 1 pc. (6,000m3/h – 200mm SS) ✔️ 36W LED lighting x 1 pc. ✔️ Bottom drawer x 1 pc. ✔️ Control panel for controlling air intake and pressure blasting ✔️ DELTA frequency converter ✔️ Heavy-duty casters under the paint booth. ✔️ An additional filter is located at the fan outlet. ⭐ E-Coat+3 Master powder coating gun with multicolor (vibration table) Request now – Make your business fit for the future! ☀️ 2-YEAR WARRANTY ☀️ ☀️We have CE certifications for all our machines and ATEX certifications for the necessary machines.☀️

Condition: new, Unused bin washer. Bought for a contract which never materialised. Fsdpjtpv T Nsfx Ab Tjgk

Condition: new, Year of construction: 2025, machine/vehicle number: SÇ 211 ALUMİNYUM PVC ÇOKLU ORTA KAYIT ALIŞTIRMA MAKİNESİ, - Notching (milling) process with adjustable linear motor movement - 5 adjustable resting systems for different profiles - Quick blade change feature that makes work easier - Notching of center register profiles between 1/6 pieces - Profiles are fixed in the machine with pneumatic vertical and horizontal clamps - Independent operation of vertical and horizontal clamps - Spare knife storage cabinet on the front of the machine - Notching (milling) of 2.5 meter long profiles by means of support arm - Maximum profile notch height ( h ) 140 mm OPTION Fgedpeq U S Disfx Ab Tsk - Spray cooling system - 220 volt operation

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 3,500 mm, total length: 7,050 mm, total width: 4,100 mm, volume flow: 36,000 m³/h, temperature: 80 °C, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), Equipment: cabin, lighting, Paint and Drying Booth It is the centerpiece of your entire painting operation: the combined paint and drying booth. Fgodpfx Abexa H Ews Tjk (Alternatively available as a separate paint booth with a dedicated dryer.) Our solutions feature full-surface ceiling filters and, optionally, full-surface floor extraction with drive-over grating or wall extraction at the position of your choice. If you wish to further increase the efficiency of the system beyond heat recovery and infinitely variable control via frequency converter, we can also offer you a sectional control system. This enables you, for example when doing spot repairs or partial booth loading (such as painting only add-on parts), to activate only the section where the parts are located. This allows you to operate with a reduced air volume, save energy, and minimize costs, all without compromising quality. Feel free to contact us – we would be happy to demonstrate these options in detail. Do you have any questions or suggestions? We are happy to assist you.

Condition: as good as new (ex-display), Brand new, unused. Double door twin dolav washer, will also wash tote bins. Still in its protective wrapping. Rare opportunity! Fgedjvvw Nijpfx Ab Tjk

Condition: new, Powder Coating Systems For years, powder coating has been continuously evolving as an alternative to wet painting, and it has recently gained increasing importance due to its lower environmental impact—specifically the absence of solvents and paint sludge. Powder recovery further boosts the efficiency of these systems to a particularly high level. For users, powder coating offers the advantage of creating an extremely durable and corrosion-resistant surface that is significantly more impact-resistant than what traditional painting can achieve. Additionally, post-processing tasks such as grinding or drilling the powder-coated parts present no problems, as the coating will not chip off. Pony Luxury Coating powder coating systems provide you with tangible advantages: they are efficient, environmentally friendly, and—as always—unsurpassed in flexibility. We achieve this through a range of system types. Manual Powder Coating Systems Manual coating systems are the ideal solution for complex and demanding workpieces. Thanks to skilled operators, these systems offer continuous adaptation to changing conditions and varying product sizes. Flexibility is paramount—with the added benefit of an attractive entry price into the world of powder coating. Large-Scale Powder Spray Booths No matter how large or challenging your workpieces, our systems are larger! In the commercial vehicle and utility sector, where components are exposed to significant stress, powder coating has established itself as the ideal solution. To accommodate ever-larger components, we offer our large-scale powder booth, which supports unlimited manual coating, and, when combined with a conveyor system, handles any workpiece size with ease. Automatic Powder Coating Systems If your operation requires high throughput and rapid processing, an automated powder system is the way forward. Coupled with a conveyor, light barriers allow precise detection and, consequently, exact powder dosage to ensure maximum efficiency. The system can also be equipped with lifting stations and robots to handle even the most complex components. Powder Curing Ovens & Flash-Off Dryers These provide the perfect finishing touch to powder coating: the curing oven. Our ovens feature the highest insulation class, ensuring consistent, high efficiency. Detailed temperature control also enables use as a flash-off dryer to dry substrates after pre-treatment. Temperatures up to 250 degrees Celsius are possible, which allows usage as a tempering oven, for instance with hot-dip galvanized materials. Of course, typical use as a powder curing oven is straightforward. Optimal air distribution and a visualized control panel prevent over-baking, and even allow multiple color shades to be cured in a single process. Fgjdpjxa Hzxjfx Ab Tok Do you have questions or suggestions? We are happy to assist you!

Condition: new, Equipment: cabin, Stationary small parts spray booth Dixi █████ Achieve perfect and uniform coating of small parts. The extraction system ensures optimal results even in the smallest spaces. Optionally equipped with a turntable or a wheel holder, as well as a compact yet powerful extraction unit, it is perfectly suited for processing small workpieces and wheels. The side panels effectively limit the distribution of overspray, allowing work to be carried out in confined spaces without contaminating surrounding areas. Integrated lighting is also available as an option. Additionally, thanks to its low weight and minimal connections, the booth can be relocated to a new site in no time, ensuring your flexibility at all times. The system comes fully pre-assembled and ready for immediate use. Your Benefits Thanks to its compact design, flexible dimensions, and versatile accessories, this booth offers a broad range of applications. The sophisticated modular system requires minimal space and is therefore suitable for use in virtually any premises. Fodpfxoxa Hx Rs Ab Tsgk Different filter media and stages enable highly efficient operation, while filter changes can be performed in just a few minutes. Application and Safety Processing of both water-based and solvent-based coating materials is enabled by the use of ATEX-certified explosion-proof motors. It can also optionally be used for spraying adhesives. The large filter surface ensures uniform extraction throughout the process.

Condition: new, Year of construction: 2024, functionality: fully functional, total length: 3,400 mm, total height: 2,210 mm, total width: 1,505 mm, type of input current: three-phase, warranty duration: 24 months, temperature: 250 °C, heating capacity: 30 kW (40.79 HP), inner dimension length: 2,500 mm, Equipment: emergency stop, ✈️ Plus shipping costs – Shipping available upon request.✈️ Fast delivery: Only 6 weeks after receipt of payment! ✅✅✅Energy Class A+++✅✅✅ ✅ Plug & Play system – Delivered fully assembled, ready to use immediately! ✳️ Maintain your liquidity! We offer a variety of financing options to ensure your investment has the best chance of success. Contact us today to learn more about our hire purchase, warranty, or leasing programs. ☘️Environmentally friendly☘️⚡️Green energy⚡️☘️ PEF-2.5 ELECTRIC POWDER FIRING OVEN WIDTH (INTERIOR): 1,505 mm HEIGHT: 1,800 mm (from the air duct) LENGTH (INTERIOR): 2,500 mm ➢ The thermoblock unit measures 785 x 1,800 x 2,210 mm. The heating capacity is 30 kW/h. A circulating fan is 1.5 kW/h (1 pc.), and an exhaust fan is 0.54 kW/h. ➢ Double-leaf door with thermal insulation and silicone seal. ➢ Guide rails are manufactured for trolleys in the dimensions indicated on the floor panels. ➢ Specially designed air duct ensures uniform air distribution in the curing oven. ➢ The electrical switchgear is made of Siemens and Schineider. This curing oven does not have a PLC system. PLC is available as an option. ➢ Curing temperature, curing time, and heating unit function are adjustable. At the end of the program, an audible and light signal is emitted by the buzzer. ➢ Additionally, a product transport cart with cast wheels is located inside the oven. 2. PKF-4 POWDER COATING BOOTH ➢ DIMENSIONS: 800x1930x2200mm (dimensions including fan) ➢ Teflon filters: 4 pcs. ➢ Filter suction fans: 4 kW x 1 pc. (6,000 m3/h – 200 mm SS) ➢ 36 W LED lighting x 1 pc. ➢ Bottom drawer x 1 pc. ➢ Fedpfx Aewdtfuob Togk Control panel for controlling air intake and pressure blasting ➢ DELTA frequency converter ➢ Heavy-duty rollers under the paint booth. ➢ An additional filter is located at the fan outlet. ♨️ Ramp heating mode (optional) Precisely control temperature progression and dwell times, e.g. E.g.: • Reach target temperature within a defined time • Maintain desired time • Controlled cooling to target temperature • Automatic notifications of process events _____ 🛡️ Safety is our priority 🟢 Safety sensors to prevent overheating 🟢 Automatic shutdown in the event of a fault 🟢 Acoustic warning signals in the event of errors 🟢 Solvent and fume removal via automatic venting _____ ⚡ Customized energy and heating system 🔥 Also available with an extension up to 400°C for high-temperature processes (optional) _____ 🧠 No repeated settings necessary! The furnace saves your process parameters – batch by batch. This saves you time and avoids errors. _____ 📢 And best of all: If you have special requirements – we also build customized furnaces according to your specifications! Contact our team of experts for a personalized consultation! _____ ☀️ 2-YEAR WARRANTY ☀️ Request more information