Used Bearing for sale (2,879)

Condition: ready for operation (used), Year of construction: 2024, workpiece height (max.): 60 mm, feed rate X-axis: 10 m/min, spindle speed (max.): 16,000 rpm, control type: PLC-controlled, The machine has already been disassembled and stored by a specialist. TECHNICAL DETAILS Rotational speed of the miter saw station: approx. 16,000 rpm Rotational speed of the milling station: approx. 16,000 rpm Maximum milling depth: 3 mm Design for edge thickness: 1 mm Hot melt adhesive specification for edge material max.: 3 mm Feed rate: approx. 10 m/min Maximum workpiece thickness: 60 mm EQUIPMENT Maintenance-free, coated glue basin with provision for interchangeable basins Glue dispensing device Hedpfozb Idfjx Aahsp Pneumatic milling adjustment Combination design with interchangeable plate cutter Corner rounding milling cutter Radius drawing blade Surface drawing blade with pneumatic extraction device Cleaning station Robust chain drive Ball-bearing mounted double roller pressure pad Aggregate viewing window from the machine's rear and operator side Signal lamp for workpiece sequence Extendable workpiece support ACCESSORIES Hebrock 8 mm version Hebrock quick-change system for corner milling cutter Hebrock jointing up to 60 mm workpiece thickness Hebrock protective spray for edges Hebrock nesting (milling cutter + radius drawing blade) Hebrock Airtronic Note: Accessories are provided without guarantee. The principle applies: "Item purchased as seen." The prospective buyer must verify the completeness of the item on-site.

Condition: ready for operation (used), Year of construction: 2002, functionality: fully functional, machine/vehicle number: 7402-09-03006-03, spindle bore: 90 mm, rotational speed (max.): 2,000 rpm, center width: 3,000 mm, center height: 325 mm, controller model: SIEMENS SINUMERIK 810D, TECHNICAL DETAILS Swinging diameter over bed: 630 mm Swinging diameter over carriage: 380 mm Center height: 325 mm Distance between centers: 3,000 mm Carriage overhang on bed: 700 mm Bed width: 520 mm Longitudinal travel X-axis: 355 mm Longitudinal travel Z-axis: 3,000 mm Tailstock spindle diameter: 100 mm Tailstock spindle travel: 180 mm Hjdozc Hmnspfx Aahsp Maximum workpiece weight between centers: 3,000 kg Maximum workpiece weight in cantilever mode: 500 kg Spindle bore: 90 mm Spindle mounting: DIN 55027/8 Spindle taper: 120 mm Front spindle bearing: 130 mm Main drive power 100% ED / 40% ED: 12 / 18.5 kW Maximum torque: 2,400 Nm Speed: 2–2000 rpm Speed ranges: 3 Range 1: 2–220 rpm Range 2: 50–660 rpm Range 3: 100–2000 rpm Speed control: 50–120 % MACHINE DETAILS Control system: SIEMENS SINUMERIK 810D Load display on screen: 0–140 % Main drive: 10 kW Power supply: 3 × 400 V / 50 Hz Dimensions & Weight Dimensions (L (with chip conveyor) x W x H): 5,600 x 1,950 x 1,850 mm Machine weight: approx. 5,500 kg

Condition: ready for operation (used), Year of construction: 2018, functionality: fully functional, turning diameter: 460 mm, spindle speed (max.): 3,500 rpm, spindle bore: 86 mm, bar passage: 78 mm, controller model: Fanuc 32iTB iHMI, center width: 689 mm, CMZ turning and milling center including GL20II gantry loader! TECHNICAL DETAILS Turning diameter over bed: 760 mm Turning diameter over cross slide: 600 mm Hodpjzdrzxofx Aahjp Maximum turning diameter: 460 mm Distance between centers: 689 mm Travel distance tailstock: 640 mm Travel distance X-axis: 310 mm Travel distance Z-axis: 640 mm Travel distance Y-axis: +70/-50 mm Travel distance B-axis: 640 mm Rapid traverse rates: 30/30/15/30 m/min Spindle speed max.: 3,500 rpm ASA 8" A2 Spindle bearing outer diameter: 200 mm Spindle bearing inner diameter: 130 mm Spindle bore: 86 mm Bar passage: 78 mm Number of tool stations: 12, all driven, 12,000 rpm Tool holder: 25x25 (50) MACHINE DETAILS Operating hours: 43,712 h Total operating hours: approx. 35,000 h Control system: Fanuc 32iTB iHMI Dimensions & Weight Machine dimensions (L x W x H): 2,542 x 1,760 x 1,880 mm Machine weight: 6,500 kg EQUIPMENT Gantry loader

Condition: ready for operation (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: 16065, travel distance X-axis: 1,200 mm, travel distance Y-axis: 900 mm, travel distance Z-axis: 500 mm, controller model: HEIDENHAIN iTNC 530, spindle speed (max.): 16,000 rpm, The seller can handle the disassembly and loading for €1,250! TECHNICAL DETAILS Travel range X-axis: 1,200 mm Travel range Y-axis: 900 mm Travel range Z-axis: 500 mm Hodpezdttpsfx Aahsp Spindle speed: 16,000 rpm Tool holder: SK 40 Milling spindle diameter at the front bearing: 70 mm Table clamping surface: 1,400 x 900 mm MACHINE DETAILS Control system: HEIDENHAIN iTNC 530 EQUIPMENT Tool changer

Condition: like new (used), Year of construction: 2021, functionality: fully functional, machine/vehicle number: PW2000-003, workpiece weight (max.): 2,000 kg, overall weight: 1,310 kg, table length: 1,400 mm, table width: 900 mm, The machine is in like-new condition! TECHNICAL DETAILS Maximum load capacity: 2,000 kg Tables and support surfaces Number of tables: 2 Support surface per table: 1,400 x 900 mm Swiveling movement Swiveling angle of the tables: 100° Angle of the load-bearing steel profiles: 90° Hodpfx Aaezd A Rdehsp Table travel distances: approx. 300 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): approx. 2,600 x 1,800 x 1,300 mm Machine weight: 1,310 kg Machine operating principle: The turning device consists of two opposing tables, each with a support surface of 1400 x 900 mm. On the side of the table that is facing downwards during swiveling, the load-bearing steel profiles are angled upwards by 90° in order to securely hold the plate to be turned even in a vertical position during the 90° swiveling process. Both tables are arranged opposite each other and are swivelled by 100° using hydraulic cylinders. The tables are mounted on a load-bearing substructure, on which one table is fixed and the other is movable relative to it. The movement is carried out by hydraulic cylinders, which can move the table, which is mounted on rollers, by approximately 300 mm. The substructure also supports the hydraulic and electrical components. A hydraulic unit serves as the drive source, supplying the cylinders with oil according to the control commands. The corresponding valves are electrically and/or hydraulically controlled and initiate and maintain the movements of the tables required for their interaction until the turning process is completed. Particular attention is paid to the safety of the movements and the precise adjustment of the table movement in the interaction between pressure and tension when designing the hydraulic system. The geometry of the axes of rotation of the tables results in a change in the load effect on the tilting cylinders. The hydraulics are designed in such a way that the required performance is ensured and an overload of the components is not possible during normal operation. Corresponding filters, combined with a generously sized tank volume, ensure a high availability of the hydraulic system. The necessary electrical control is completely housed in a steel sheet metal enclosure, which contains all the required components. The core of the control is a PLC, in which the operating parameters are processed according to the program specification. In addition, the emergency stop function and all the relays and output units required to control the functions are installed. The turning device is operated via a control panel in which a touch panel is used to input the function parameters, such as swivel table 1 up, swivel table 1 down, move table 1 forward, move table 1 backward, swivel table 2 up, swivel table 2 down, as well as start or stop the automatic mode. In order to avoid a collision of the tables in manual operation, the PLC programming is designed in such a way that this is prevented by the data on the table position and the respective table inclination. After the emergency stop situation has been resolved, the PLC control automatically completes the turning process. The turning device is equipped with heavy-duty rollers and can therefore be moved.

Condition: new, Year of construction: 2026, overall weight: 2,800 kg, rotor diameter: 350 mm, number of blades: 42, total length: 1,460 mm, total height: 1,800 mm, total width: 1,950 mm, rotor length: 620 mm, rotor width: 350 mm, power: 35 kW (47.59 HP), warranty duration: 12 months, blade width: 50 mm, blade diameter: 50 mm, MIZAR SSH Series - Single Shaft Shredder / Einwellenzerkleinerer for Cables, Plastics & E-Waste Controlled Size Reduction with Intelligent Feeding System The MIZAR SSH Series is engineered for efficient and controlled shredding of a wide range of materials including cables, textiles, plastics, tires, electronic scrap, and various metal types. Designed for reliability, flexibility, and consistent output size, SSH shredders are ideal for recycling facilities requiring uniform material preparation before granulation or further processing. Hsdoyyun Ajpfx Aahjp SMART SHREDDING TECHNOLOGY & ADVANTAGES • Single Rotor – Maximum Control: Customized high-alloy wear-resistant steel blades mounted on a robust single shaft ensure aggressive intake and efficient size reduction across mixed material streams. • Programmable Hydraulic Pusher: An intelligent hydraulic feeding system continuously pushes material toward the rotor, optimizing throughput and preventing idle rotation. • Automatic Anti-Jam System: In case of overload or blockage, the rotor automatically reverses direction. This protects the machine and ensures uninterrupted operation. • Screen-Controlled Output Size: A heavy-duty screen located beneath the rotor determines the final particle size. Material remains inside the chamber until it reaches the required dimensions, ensuring a homogeneous output. • Industrial-Grade Components: Siemens/WEG motors, SKF/FAG bearings, and Schneider or ABB electrical systems ensure durability and long service intervals. Fully CE-certified for international compliance. APPLICATION AREAS • Cable Recycling: Copper and aluminum cables, wiring harnesses. • Plastic Materials: HDPE, PET, film, lumps, injection waste. • Electronic Scrap (WEEE): PCBs, electronic components, mixed e-waste. • Textile & Tires: Industrial textile scrap, fabric waste, car and light truck tires (pre-cut). • Metals: Aluminum scrap, radiators, light metal fractions. MODEL RANGE & TECHNICAL HIGHLIGHTS (Please ask for the exact configuration and screen size based on your material) • SSH S1: Compact solution for medium-scale operations. • SSH M1: Balanced performance for diverse recycling needs. • SSH L1: High-capacity industrial model for continuous operation. • SSH XL1: Heavy-duty configuration for the most demanding throughput requirements. Why Mizar SSH? • Precise output size control via interchangeable screens • Stable and intelligent hydraulic feeding system • Reduced downtime with automatic reverse function • Low maintenance design with accessible rotor chamber • Seamless integration into complete recycling lines Need a tailored shredding solution? Contact us for a customized quotation, technical drawings, or send your material for a performance test. Mizar Recycling Machinery

Condition: ready for operation (used), Year of construction: 2009, spindle speed (max.): 2,500 rpm, total height: 1,785 mm, overall weight: 3,850 kg, number of axes: 2, This Weiler E50 was manufactured in 2009. A robust horizontal turning machine featuring a swing diameter over bed of 570 mm and a spindle bore of 83 mm. It offers a bed width of 350 mm and a turning tool cross-section of 32 x 25 mm. Ideal for precise and efficient turning operations. Contact us for more information about this machine. Machine Benefits Qualitative Machine Benefits • Spindle diameter in the front bearing: 120 mm • Spindle bore: 83 mm • Inner taper of the main spindle: metric 90 • Feed range longitudinal and planar: 0-20 mm/rev • Feed force longitudinal: 10000 n • Feed force planar: 7000 n • Input speed longitudinal/planar: 10/7 m/min or 5/3. 5 m/min • Metric threads: 0. 1-400 mm • Inch threads: 1/4" - 56 g/1" • Module threads: Technical Machine Benefits • Drive power (60% / 100% ed): 20/17 kw Hsdpfx Aox D Ibbsahjp • Max. Torque at the turning spindle: 1600 nm • Gear stage i: 1-625 min-¹ • Gear stage ii: 4-2500 min-¹ • Bed width: 350 mm • Quill diameter: 80 mm • Quill stroke: 200 mm • Inner taper of the quill: mk 5 • Turning tool cross-section (height/width): 32 x 25 mm • Spindle head according to din 55027: size 8 Extra Information Machine still under power/ DP threads: 1 - 224/ Fixed steady rest clamping range: 12-150 mm / 120-270 mm/ Moving steady rest clamping range: 12- mm/ The machine has been working effectively in 1-shift operation since it was purchased/ The chuck incl. hard & several sets of soft jaws and the tailstock can be supplied as accessories (optional)/ Any associated tools could be discussed in the event of an order (otional)/ The footprint of the machine is 2.8m x 5.2m, the 2.8m already includes 600mm as a workstation/ All manuals are available. Dimensions Machine Depth 3250 mm

Year of construction: 2021, condition: ready for operation (used), functionality: fully functional, EV Car Motor Assembly and Testing Line (2021) Designed to produce EV motors in the power range of 180–300 kW Including manual, semi-automated, and automated operations Cycle time: 86s Stations and Equipment Component loading - KUKA KR15 R2700-2/FLR robot (2021) - Material infeed - Inner housing heating with induction coil up to 240 °C - Stator pressing into housing - 1T TOX press - Keyence CA-DQP25X - Cooling tunnel - Cooldown to 24 °C - Cycle time: 600 s X-ring and D-ring inner housing assembly - X-ring and D-ring seal insertion into housing - Dedicated round assembly tool available Outer housing pre-assembly - Flange screw into housing with Bosch Rexroth ESA013G-G0 screwdriver - Automatic inner and outer housing joining Outer housing assembly - 3T TOX EQK 030 press - 2x Cognex scanners - 2x Keyence Camera V3 - 3x VS camera systems Rotor magnetization and measurement - Magnet magnetization - MagSys magnetizer MC3K82 (2020) - Magnetizing fixture MFFer8/160/250 A-shield pre-assembly and rotor insertion - Rotor bearing and resolver pressing - 3T TOX press A-shield assembly into outer housing - 1T TOX EQK press - A-shield screwing into outer housing with pneumatic screwdriver (5 Nm) Mounted component fastening - Fastening with 4GE59 Rexroth screwdriver Hjdpozhub Asfx Aahop - Manipulator system Handyflex 400 Inter-connector connection - Manual mounting of inter-connector and insulating tube Counter ring insertion, cooling cover, and vent assembly - 3T TOX EQK 030 press Rotor cooling cover mounting - Screwing with 4 Nm End-of-line (EOL) electrical testing loop - 5x Deutronic testers, including: - ETL ATS 400 high-voltage testers - HIOKI RM3545 resistance testers - Reilhofer EOL analyzers Inter-connector disconnection station - Disconnection of the inter-connector - Insertion of 2 screws and screwing with Rexroth screwdriver (13 Nm) - Manipulator system Handyflex 300 - Washer control - Motor rotation Leak testing - 2x Leak test stations with Innomatec LTC-902 testers - Vacuum and overpressure leak tests - Tested quantity: approx. 50,000 pcs per test station Rotation, laser marking, stamping, engraving, and inspection - ADT stamping machine - Arex Laser 450 - Keyence CA-H camera system - Datalogic CBX 100 reader - Tested quantity: approx. 130,000 pcs Transportation protection - Yellow transportation cover/cap and plug assembly - Manual insertion of caps and hole securing Packaging and final inspection - Dalmec manipulator (2022)

Condition: excellent (used), Year of construction: 2010, chuck diameter 210 mm max. swing diameter over bed 500 mm Hedpfx Aaezhpamjhep swing diameter over slide rest 290 mm turning diameter 200 mm centre distance 700 mm turning length 500 mm travel -y axis 80 (+/-40) mm travel -x axis 190 mm travel -z axis 525 mm spindle bearing diameter 100 mm bar capacity 65 mm spindle bore 73 mm spindle turning speed range 6000 U/min turret (x-stations) 12 work piece power 4,18 kW speeds of tool 5000 U/min VDI 30 control Siermens 840D total power requirement 20 kW weight of the machine ca. 4,3 t dimensions of the machine ca. TBH 2,2 x 4,5 x 1,82 m Very well-maintained machine from a training workshop that has closed down. Power-on hours: 14,944 h. Spindle hours: 2,233 h. Includes current measurement report (available upon request) Includes Y-axis Includes C-axis Includes approx. 10 tool holders (including 2 driven units: EWS axial/radial) Includes SMW 3-jaw chuck Includes tailstock center Includes tool probe arm Includes chip conveyor Includes parts unloading arm with conveyor belt Includes coolant system Includes documentation

Condition: new, - Large jointer tables made of cast iron - The jointer table adjustment is controlled via a precise parallelogram system, ensuring that the distance from the table tips to the cutterhead remains constant in every position - The large, stable fence made of anodized aluminum is easily movable and tiltable from 0° to 45° - The fence angle is readable from the working position - Supplied as standard with auxiliary fence - Large, four-knife cutterhead with precision bearings - Smooth operation thanks to precision engineering and heavy cast construction - Powerful industrial motor - Maximum user safety combined with the simplest operation - Chip removal display via scale - Manual table adjustment - Motor protection switch Hjdpfx Aou T Hrcjahop Equipment Details -Includes foldable auxiliary fence for narrow workpieces -Manual quick adjustment for chip removal with scale and rotating knob Safety Guard -The safety guard is foldable and designed to provide operator protection without hindering work TERSA Models with Tersa Cutterhead System -No setting or screwing required -Cutter knives can be changed in seconds -Self-locking -Especially quiet operation -Perfect planing results This product comes with the 3-year Stürmer warranty upon online registration. Warranty only applicable to end customers in Germany and Austria. Manufacturer SCM Group S.p.A. Via del Lavoro 1/3 - PO Box 168, 36016 Thiene-Vicenza, Italy Dimensions and Weight: - Product length approx.: 2750 mm - Product width/depth approx.: 1500 mm - Net weight approx.: 680 kg Jointer: - Total table length: 2720 mm - Infeed table length: 1498 mm - Max. depth of cut on jointer: 8 mm - Fence length: 1200 mm - Fence height: 190 mm - Fence tilt range: 90 – 45° Connection for extraction: - Extraction port diameter: 120 mm Setup Information: - Footprint length: 2750 mm - Footprint width/depth: 1604 mm - Footprint explanation: Dimensions reflect maximum travel or usable lengths. Electrical Data: - Main motor power: 7 kW - Connection voltage: 400 V - Mains frequency: 50 Hz Cutterhead: - Cutterhead type: TERSA - Cutterhead diameter: 120 mm - Number of knives: 4 - Cutterhead speed: 5000 rpm - Max. planing width: 520 mm

Condition: new, GRAULE ZS 85 N cross-cut and mitre saw - tiltable - Includes: - GRAULE ZS 85 N cross-cut and mitre saw - inclinable - Material feed shoulder made of laminated wood - without machine stand and saw blade - Including: - GRAULE machine stand for type ZS 85 N to ZS 170 Hodpfx Aou R Sycoahsp Includes: - GRAULE type RO feed roller conveyor complete with support feet and connection bracket Plastic rollers with ball bearings Ø 40 mm, Roller width 300 mm, roller spacing approx. 300 mm, Support feet for roller conveyor height 885 +/- 10 mm Includes: - GRAULE type RLK roller conveyor/length stop with scale and material stop that can be folded back. Ball bearing mounted plastic rollers Ø 40 mm, Roller width 300 mm, roller spacing approx. 300 mm, Support feet for roller conveyor height 885 +/- 10 mm - new exhibition machine -

Condition: new, GRAULE ZS 170 N cross-cut and mitre saw - tiltable - Includes: - GRAULE ZS 170 N cross-cut and mitre saw - tiltable - - without machine stand and saw blade - Including: - GRAULE machine stand for type ZS 135 N and ZS 170 N Includes: - GRAULE type RO feed roller conveyor complete with support feet and connection bracket Plastic rollers with ball bearings Ø 40 mm, Roller width 300 mm, roller spacing approx. 300 mm, Support feet for roller conveyor height 885 +/- 10 mm Includes: - GRAULE type RLK roller conveyor/length stop with scale and material stop that can be folded back. Ball bearing mounted plastic rollers Ø 40 mm, Roller width 300 mm, roller spacing approx. 300 mm, Support feet for roller conveyor height 885 +/- 10 mm Hsdsu R Sypjpfx Aahep - new exhibition machine -

Condition: new, Vacuum lifter BARBARIC B3 swiveling, incl. crane - Exhibition unit - Including: - Vacuum lifter BARBARIC uniWood UWL 3, 150 kg Vertical and horizontal transportation of flat commercial commercially available boards (coated boards, natural wood panels) up to a panel size of 3,000 x 2,100 mm - a tilting range of 90° with pneumatic tilting mechanism - Complete with hoist and corresponding safety devices safety devices (vacuum manometer and manual manual slide valve with mechanical safety device) - uniWood traverse with 2 suction pads Ø 270 mm on an adjustable traverse (traverse length: 1,500 mm) Includes: - Optional reinforced BARBARIC uniWood version for easily permeable boards Load capacity: 250 kg with 2 oval suction pads 500 x 250 mm on an adjustable cross beam (cross beam length: 1,250 mm) and reinforced vacuum pump for permeable Hsdpfju R Szajx Aahep sheets. The reinforced design enables lifting materials weighing up to 250 kg. Includes: - BARBARIC uniWood comfort operation option All controls for the lifting gear and for the vacuum the vacuum lifter are integrated in one control unit - our special handling handle is accommodated. This makes it possible to operate the system and guiding the load in one-handed operation. The lifting process can be steplessly controlled by a frequency converter. The comfort version comes complete with hoist and corresponding safety devices (vacuum pressure gauge and 2-button safety control for releasing the load). Includes: - BARBARIC column-mounted slewing jib crane Lifting capacity on the lifting device: 250 kg The lifting capacity is the specified working load on the lifting device. Barbaric slewing jib cranes are designed for handling tasks in all areas of application and are extremely lightweight. SSK consisting of column, bracket and smooth-running jib. jib. Slewing and trolley travel by hand. The prerequisite for attachment is a suitably concrete floor (C20/R5, min. 20 cm). The static inspection of the floor must be carried out on site and documented accordingly. For fastening on cracked concrete or less load-bearing substrate, we offer enlarged base plates enlarged base plates on request. Fastening: Supplied with adhesive anchor for concrete floor When ordering without lifting gear, please specify the cable or hose type! Delivery includes: incl. sliding trolley, power supply and compressed air connection. - new exhibition machine -

Condition: new, Holzkraft L invincibile si 3 BLADE OFF sliding table saw BLADE OFF safety system - exhibition machine- ----- Technical specifications ----- Supply voltage: 400 V, Mains frequency: 50 Hz, Scoring motor power: 1.3 kW, Drive motor power: 9.0 kW, Format sliding table length: 3200 mm, Format sliding table width: 360 mm, Table length: 1040 mm, Table width: 630 mm, Cutting width with parallel stop: 1500 mm, Max. cutting width to the left of the sawblade: 3200 mm, Trimming length: 3200 mm, Sawblade inclination: 90 - 45°, Max. cutting height 90° with 400 mm sawblade: 120 mm, Max. cutting height 45° With 400 mm saw blade: 89 mm, Saw blade speed: 3000 - 5000 rpm, Scoring saw blade diameter: 120 mm, Scoring saw blade speed: 8500 rpm, Length approx.: 7250 mm, Width/Depth approx.: 4460 mm, Height approx.: 1770 mm, Net weight approx.: 1307 kg, Extraction nozzle diameter: 100 and 120 mm The BLADE OFF system detects potential hazardous situations early and prevents them by retracting the saw blade into the machine table in a fraction of a second. With the help of sensors, the system is able to distinguish between the workpiece and the operator. An LED light in the saw blade guard indicates with a green light whether the safety system is active. Controlled via the 15" eye-S control console. Connection to the SCM Thundercut (optimizer/sequence control app) is possible. Three longitudinal stops with integrated digital displays. Electrically adjustable parallel stop. Start/stop buttons for the main and scoring saw blades integrated in the sliding carriage. Special guides and an innovative curved grinding system enable the edger carriage to have a fourfold higher load capacity. Ball-bearing telescopic arm ensures greater stability and smoother workpiece guidance. Hsdov Nhg Sepfx Aahep Equipment Two-axis scoring unit with automatic positioning Anodized aluminum sliding table On/off switch on the sliding table for the main and scoring sawblade motors Trimming frame with angle-adjustable aluminum telescopic stop Material roll on the trimming frame Motorized saw parallel stop via control panel Three longitudinal stops with integrated digital displays Eccentric clamp Control of sawblade height, tilt, and parallel stop Pivoting control panel on top Table extension Table extension Sawblade pendulum protection - new exhibition machine -

Condition: like new (used), functionality: fully functional, Year of construction: 2026, container length: 10 ft, For sale: Like-new 10-foot containers 🇩🇪🚨 These containers have barely been used and are in excellent technical and visual condition, almost as good as new. Condition & Features: ✅ Wind- and waterproof ✅ Robust steel construction ✅ Smooth-running double doors with original locking system ✅ High security with heavy-duty door rods ✅ Floor is dry, clean, and highly load-bearing Technical specifications: External dimensions: 2,991 x 2,438 x 2,591 mm (L x W x H) Internal dimensions: approx. 2,831 x 2,352 x 2,390 mm (L x W x H) Volume: approx. 15.9 m³ Tare weight: approx. 1,200 - 1,330 kg We also offer 8-foot containers! Feel free to contact us! Possible uses: Storage container for tools, machinery, or materials Construction sites, businesses, or private use Gardens, courtyards, clubs, or workshops Also ideal as a base for conversions (workshops, storage, tiny house projects) Hjdpfewu Unlox Aahop 🚚 Delivery available by arrangement! If you're interested, just get in touch – I reply quickly and reliably. 👍

Condition: reconditioned (used), Year of construction: 2010, • Traveling distances X=3100 mm, Y=1950 mm, Z=1390 mm • Heidenhain iTNC 530 with handwheel HR 410 • Machine table for multi side working 3000 mm x 1600 mm • 2-axis NC-universal milling head, for simultaneous and positioning working • Spindel 10.000 U/min HSK 100, 130 Nm Spindle torque • Tool change system HSK 100 / 40 places for 750 mm long tools • Chip conveyor (screw type) in X-axis, for transport into • Chip conveyor scraper belt type (traverse conveyor), Fabr. Knoll • Coolant container 900 l, Fabr. Knoll • Outside air at spindle • IKZ 60 bar for deep hole drilling function • Covering with safety glass pane, open at the top for loading by crane • 2 part sliding doors at the operator side • 2 part sliding doors at the front side, for easy loading • Radio-controlled measuring probe RMP 60 • incl. washing gun • incl. podiums at the front side and operator side • complete factory overhauled and painted new • short time delivery after arrangement • used machine Hjdpozhlgcsfx Aahop • Y-axis ball screw in September 2021 incl. bearings renewed • X-axis new linear guiding system, July 2023 changed, renewed • Spindle overhauled at Mai 2023 (clamping system new, clamping cartridge new, rotation unit new, general tests) (at 23105 spindle hours)) • can be visited under power at 72793 Pfullingen • optional fixators • optional installation at customers plant • optional transport • 23122 spindle hours in total • 53991 machine hours in total • Year of construction 2010 Subject to prior sale

Condition: excellent (used), Year of construction: 2007, BA 600-2 CNC, Horizontal Milling and Drilling Center SW Schwäbische Werkzeugmaschinen GmbH Travel: X axis: 600 mm Y axis (changeover position): 600 (975) mm Z axis: 500 mm Control: Siemens 840D control, side-mounted Feed/Rapid traverse speeds: X, Y, Z: 1 – 45,000 mm/min Max. feed force X, Y, Z: 15,000 N Average acceleration: X, Y, Z: 2.5 m/s² Measuring system: Direct measuring system X, Y, Z Spindles: Spindle speed (infinitely variable): 20–10,000 rpm Torque: 2 x 363 Nm (S6/40% duty cycle) Power: 2 x 38 kW (S6/40% duty cycle) HSK-A 100, horizontal tandem arrangement Spindle distance: 600 mm Hjdjzhlfropfx Aahop Spindle bearing diameter: 100 mm Motor spindles, liquid-cooled, AC technology Working area: Swing carrier with spur gearing, max. workpiece weight 2,000 kg Swivel time 0/180 degrees approx. 6.0 sec 2 NC rotary tables, hydraulically clamped, max. workpiece weight 700 kg, table speed 25 rpm Partition between machining and loading area Tool magazine: 2 x 50 tools HSK-A 100 chain-type magazine Tool change time (chip-to-chip): 4.48 sec Max. tool diameter: 100 mm 250 mm with adjacent slot free Max. tool length: 420 mm Max. tool weight: 20 kg Equipment: Central lubrication Oil minimum quantity lubrication (spindle lubrication) Chip conveyor (hinged belt conveyor) Coolant purification with compact band filter Hydraulic unit Maintenance unit Water recooler Full enclosure, crane loading possible Dimensions: approx. 5.15 x 8.50 x 4.20 m Weight: approx. 20,000 kg Year of manufacture: 2007 Other features: Very good condition Setup parallel to main time Available from December 2023/January 2024

Condition: good (used), Year of construction: 2004, functionality: fully functional, machine/vehicle number: KMM526 1506, travel distance X-axis: 1,000 mm, travel distance Y-axis: 400 mm, travel distance Z-axis: 360 mm, rapid traverse X-axis: 45 m/min, rapid traverse Y-axis: 45 m/min, rapid traverse Z-axis: 45 m/min, feed length X-axis: 10,000 mm, feed length Y-axis: 10,000 mm, feed length Z-axis: 10,000 mm, controller manufacturer: FANUC, controller model: SERIES 18i-MB, total height: 3,300 mm, total length: 2,700 mm, total width: 2,700 mm, table width: 470 mm, table length: 1,500 mm, spindle speed (min.): 36 rpm, spindle speed (max.): 12,000 rpm, mount diameter: 40 mm, tool length: 250 mm, tool diameter: 125 mm, input voltage: 400 V, Equipment: chip conveyor, STAMA MC 526 CNC Vertical Machining Center - Operating voltage: 400 V - Frequency: 50 Hz - Rated current: 45 A - Table with three T-slots - Incl. 4th axis - Incl. 42-position tool changer - Overhang: 350 mm - Working spindle bearing diameter: 65 mm - Incl. chip conveyor and coolant system - Note: without the clamping devices shown in the photos Hsdpfx Asx E Tt Ijahep Notice: The item must be collected bindingly between 04 and 12 March 2026 on a date to be agreed. FCA D-75181 Pforzheim – loaded onto truck

Condition: used, Year of construction: 2022, Plus freight 4,000.00 € and installation and commissioning 5,000.00 € Grinding system B Sand 5 with partial lathe Working principle The panel is placed on the infeed table. It goes into the partial lathe and centered. It is ground in the grinding system, through and back. The panel is turned in the partial lathe. It is ground on the other side in the grinding system. Then there are two options: either the panel goes onto the outfeed table and unloaded or it comes back onto the infeed table and is unloaded there (the second option extends the working time). Grinding system equipment 1 upper grinding lamella roller suitable for surfaces. Power 3 kW; D 420 mm; L 1300 mm. Cross brush suitable for grinding the cross fibers. D 420 mm; L 300 mm. Power 1.1 kW. Cross brush suitable for grinding the cross fibers. D 420 mm; L 300 mm. Power 1.1 kW. 3 upper sanding discs for perfectly trimming the longitudinal and transverse wood fibers. Power 1.5 kW each; D 400 mm. Disc brush for beveling edges. The unit functions as a deep brush. After detecting the panel edges, it will follow the door edges. Power 0.75 kW; D 250 mm. Machine features: -The unique sanding system of this machine guarantees perfect wood sanding and/or intermediate sanding of the panels. -All tools are controlled by frequency converters. -All brushes are equipped with quick-release sanding strips without replacing the hub. -The discs are equipped with air bladders to optimize cleaning and service life. -Sanding discs are equipped with a Velcro fastening system. -The feed and rotation speed are PLC-controlled to prevent edge breakage. -High-quality sanding on 4 sides thanks to the system's constant removal rate. -Automatic and rapid unit changeover. - Constant throughput height, PLC and industrial software enable interlinking in a surface line. - Continuously variable speed of the discs, brushes and feed thanks to the fully equipped frequency converter. - Right/left rotation of the discs and brushes with different abrasive grits. - Individually driven feed of the discs, rollers and belts. - Additional adjustment of the brushes and discs to balance the use of the abrasive and to allow for changing the grinding pressure on the surfaces. - Strong support bed made of tubular steel guarantees the best rigidity, stability and flatness. - Planed upper support bed to ensure the best parallelism of the working surface for the grinding discs. - All unit carriages are designed with linear recirculating ball bearing guides, thus high load capacity and high precision. - Motorized feed belt controlled by a frequency converter, 0.55 kW. Machine doors equipped with safety devices. - Machine doors equipped with windows to observe the workpieces during operation. - Under the units, there are 80 mm rubber-coated pressure rollers to hold the workpieces in place during processing. · Low follow-up costs thanks to individual blade replacement. · Low running noise thanks to the enclosed system housing. · All units have suction housings with their respective suction supports. Cover plate with suction nozzle. · Completely encapsulated machine housing for a clean environment. Hedovvkipspfx Aahep

Condition: used, Year of construction: 2008, · Working area X-Y-Z: 3,660 x 1,550 x 130 mm · Travel length X-Y: 4,200 x 2,000 mm Description of the units and accessories (base) The structure of the base body is a monolithic construction made of thick-walled steel. It is stiffened by welded triangular plates across the entire machine bed, making it extremely stable. The triangular shape used for load-bearing parts, with a large base, is the secret to ensuring lasting precision and stability. The machine layout allows the user an optimal workflow despite minimal space requirements. The base body constructed in this way therefore offers the machining unit a balanced and secure base with particularly good load distribution. The mobile unit carrier in gantry design is made of a solid monoblock. It is positioned in the X direction on prismatically ground guides via recirculating ball slides. The work unit is mounted on this mobile unit carrier on prismatic, ground guides and a recirculating ball slide. Axis movement: The drive system in the Y and Z axes is provided by ground ball screws of the highest precision class. The X-axis is driven by a backlash-free, preloaded precision rack and pinion drive. This ensures balanced load distribution during the positioning process. Such characteristics are important for ensuring balanced movement even in more complex tasks. The movement of the various axes is controlled by brushless three-phase servo motors/brushless AC motors. These offer excellent positioning speeds thanks to very short ramp times. Furthermore, the measuring system is fully integrated into these motors. These properties make this type of drive completely maintenance-free. · Rapid traverse in X: 40 m/min · Rapid traverse in Y: 60 m/min · Rapid traverse in Z: 22.5 m/min Vacuum system (basic) · Vacuum pump: 100 cbm/h · Power: 2.5 kW · Max. negative pressure (connection) 0.9 bar Control / control cabinet · Office PC or industrial PC (see options) · Basic NC control: ESA-GV KVARA 6.0 · Cable remote control with the most important functions ELECTRIC/ELECTRONIC CNC CONTROL Universal is equipped with a powerful NC control. The integrated office PC gives the NC control an unparalleled level of familiarity: the software runs on Windows XP and allows quick and easy programming, which is easy to learn even for inexperienced users. The system is open and allows the connection of CD-ROM drives, audio cards, barcode readers, modems, printers, scanning systems, etc. Furthermore, the installation of all network systems, as well as all commercially available CAD programs, is possible. To reduce space, the control cabinet is located under the machine table, and the operator works at a separate terminal on casters that can be freely positioned. XILOG PROGRAMMING SYSTEM Software features: - Import of DXF files - Import of ASCII files - User interface in the operator's native language (available for languages I - GB - F - D - E) - Linear and circular interpolation in three axes, linear in space, spiral in the selected plane - Assisted programming - Calculator for direct transfer of calculated data - Graphic and syntax aids for drilling and milling operations - Parametric programming to perform the same panel machining on different P Hsdpfevvi Nzex Aahep

Condition: used, Year of construction: 2008, · Working area X-Y-Z: 3,660 x 1,550 x 130 mm · Travel length X-Y: 4,200 x 2,000 mm Description of the units and accessories (base) The structure of the base body is a monolithic construction made of thick-walled steel. It is stiffened by welded triangular plates across the entire machine bed, making it extremely stable. The triangular shape used for load-bearing parts, with a large base, is the secret to ensuring lasting precision and stability. The machine layout allows the user an optimal workflow despite minimal space requirements. The base body constructed in this way therefore offers the machining unit a balanced and secure base with particularly good load distribution. The mobile unit carrier in gantry design is made of a solid monoblock. It is positioned in the X direction on prismatically ground guides via recirculating ball slides. The work unit is mounted on this mobile unit carrier on prismatic, ground guides and a recirculating ball slide. Axis movement: The drive system in the Y and Z axes is provided by ground, high-precision recirculating ball screws. The X-axis is driven by a backlash-free, preloaded precision rack and pinion drive. This ensures balanced load distribution during the positioning process. This characteristic is important for ensuring balanced movement even in more complex tasks. The various axes are driven by brushless three-phase servo motors/brushless AC motors. These offer excellent positioning speeds thanks to very short ramp times. Furthermore, the measuring system is fully integrated into these motors. These properties make this type of drive completely maintenance-free. · Rapid traverse in X: 40 m/min · Rapid traverse in Y: 60 m/min · Rapid traverse in Z: 22.5 m/min Vacuum system (basic) · Vacuum pump: 100 cbm/h · Power: 2.5 kW · Max. negative pressure (connection) 0.9 bar Control / control cabinet · Office PC or industrial PC (see options) · Basic NC control: ESA-GV KVARA 6.0 · Cable remote control with the most important functions ELECTRIC/ELECTRONIC CNC CONTROL Universal is equipped with a powerful NC control. The integrated office PC gives the NC control an unparalleled level of familiarity: the software runs on Windows XP and allows quick and easy programming, which is easy to learn even for inexperienced users. The system is open and allows the connection of CD-ROM drives, audio cards, barcode readers, modems, printers, scanning systems, etc. Furthermore, the installation of all network systems, as well as all commercially available CAD programs, is possible. To reduce space, the control cabinet is located under the machine table, and the operator works at a separate terminal on casters, which can be freely positioned. XILOG PROGRAMMING SYSTEM Software features: - Import of DXF files - Import of ASCII files - User interface in the operator's native language (available for languages I - GB - F - D - E) - Linear and circular interpolation in three axes, linear in space, spiral in the selected plane - Assisted programming - Calculator for direct transfer of calculated data - Graphic and syntax aids for drilling and milling operations - Parametric programming to perform the same panel machining on different Hedpfx Aovvi Rfsahsp

Condition: used, Year of construction: 2010, travel distance X-axis: 3,020 mm, travel distance Y-axis: 1,520 mm, • Monoblock structure in welded steel with a mobile gantry in steel. • Processing speed up to 18 m/min. • Worktable: fixed table made of high-thickness aluminum profiles. • Hardened linear guides and preloaded ball-bearing carriages. • Transmission via precision ball screws on all 3 axes. • CN7000 numerical control with touch screen and brushless servo drives. Hjdsxxii Aspfx Aahjp • Available in 5 sizes for maximum flexibility. • Z 350 option for 3D applications. • Quality and performance suitable for good productivity. • Well-known ease of use. • Compliant with European safety regulations. • Numerous options: brushless servomotors, micro-lubrication, automatic tool changer, vacuum table (with turbine or vacuum pump), high-frequency spindles, contact engraving spindles, fourth axis.

Condition: used, Year of construction: 2011, Technical details: standard turning dia.: 200 turning length: max. 810 mm control: MSX-701 MAPPS IV greates pass round over bed: 800 mm Max. distance between centres: 1130 mm max. turning diameter: 320 mm max. workpiecediameter: 300 mm bar material dia.: 65 mm Traverse X-Axis 1: 210 Traverse X-Axis 2: 210 mm Traverse X-Axis 3: 210 mm Traverse Y-Axis 1: 110 (+65/-45) mm Traverse Y-Axis 2: 110 (+45,/-65) mm Traverse Z-Axis 1: 300 mm Traverse Z-Axis 3: 300 mm Traverse Z-Axis 2: 810 mm Traverse B-Axis: 870 mm turning speed range - spindle: 5.000 1/min Number of spindle speed ranges: 2 . spindle nose: JIS A2-6 spindle bore: 73 mm spindle bearing diameter: 120 mm C-Axis: 0,001 ° turning speed range - spindle: 5.000 1/min spindle nose: JIS A2-6 spindle bore: 73 mm Hjdpoy S Tm Usfx Aahop bar material dia. max: 65/52 mm spindle bearing diameter: 120 mm C-Axis: 0,001 ° Number of Turrets: 3 . Number of tool stations: 16 x 3=48 pos Schank height for square tool: 20 mm Diameter of boring bar: 32 mm turret changing time (4-stations): 0,18 sec Number of driven tools: 16 x 3=48 pos max. spindle speed driven tools: 6.000 U/min. Rotary tool machining ability: M16 / Ø16 . rapid traverse X-axis: 30 m/min rapid traverse Y-axis: 20 m/min rapid traverse Z-axis: 50 m/min drive capacity - spindle motor: 25 / 22 kW power capacity - driven tools: 7,5 / 5,5 kW total power requirement: 92,7 kVA weight of the machine ca.: 9,4 t dimensions of the machine ca.: 4,0 x 2,8 x 2,4 m Accerories Chip conveyor Coolantsystem C-axis in main and sub spindle Y-axis 2 x part counter total counter tool setting Overhead partsgripper with conveyor belt. Spindle 1 Chuck SMW KNCS-N 210 / 52 mm Spindle 2 Collet Chuck Hainbuch Spanntop nova Kombi Axfix 65 Robot interface CNC Turning- and Milling Center MORI SEIKI NZ 2000 T3Y2 The NZ2000 T3Y has 2 spindles and 3 turrets, and 2 turrets have the Y-axis function and built-in milling motors. This not only allows synchronized machining using 3 turrets, but also achieves heavy-duty cutting and high-speed machining using rotary tools thanks to the built-in motor turrets. *

Condition: used, Year of construction: 2011, turning diameter over bed 640 mm turning length 2.000 mm control 840D incl. Weiler SL1 Siemens centre height 320 mm swing diameter over face slide 405 mm radial face slide travel 380 mm travel upper slide 130 mm bed width 380 mm turning tool - shaft cross cut 32 x 25 mm turning speed range - main spindle 0 - 2.500 min/-1 transmission ratio 2 transmission ratio 1 0 - 800 min/-1 transmission ratio 2 0 - 2.500 min/-1 Hjdjzhcfvjpfx Aahjp power capacity - main spindel 20,5 / 17 kW max. Torque 1.400 Nm spindle head Gr. 8 DIN 55027 spindle diameter in front bearing 120 mm spindle bore 83 mm taper bore 90 metrisch power feed longitudinal 10.000 N power feed coss 9.000 N feed range 0 - 20 mm/-1 rapid traverse 10/7 | 5/3,5 m/min metric 0,1 - 400 mm inch 1/4 - 56 G/1" module mm . II dia. of quill 100 mm quill stroke 200 mm capture MK 5 total power requirement 30 kVA weight of the machine ca. 5,7 t dimensions of the machine ca. 5,0 x 3,5 x 2,0 m Lathe cycle controled WEILER - E 60 / 2000

Condition: new, Year of construction: 2024, The subject of sale is a single-shaft shredder equipped with a hydraulic pusher. Brand/Manufacturer: 3E Machinery Model: WT40150 Main motor power: 90 kW Hydraulic system motor power: 5.5 kW Working rotor length: 1500 mm Rotor diameter: 400 mm Number of movable knives on the rotor: 94 pcs Dimensions of the movable knife: 40x40x25 mm, fastened with an M12 screw Single row of fixed knives, two-piece, the possibility of mounting a second row of fixed knives (upper) depending on the processed waste Top-loading section widened to facilitate feeding waste into the shredder Hydraulic system equipped with an oil cooling system External bearing Inspection flap opened with the screen assisted by two actuators The machine is available at our warehouse in Częstochowa. Hedpfx Aeq Sp Evoahsp Our offer includes not only individual shredding devices; upon request, we can provide a quote for a complete crushing line (conveyor feeding to the crusher, crusher, conveyor receiving with possible metal separation, grinding mill, big-bag station with a transport fan and a two-fraction cyclone). Also available in our offer: Knife mills Two-shaft crushers Four-shaft crushers Washing lines Systems for cable waste Used machines