Used Adk 125 Modell for sale (22,095)

Condition: good (used), Year of construction: 2004, Working hours : 21.447 h Clamping force: 125 tons Prodpfoxqx Avex Adned Tie-bar spacing (horizontal × vertical): 470 mm × 470 mm Platen size (mould plate) approx: 745 mm × 770 mm Minimum mould height (installation height): approx 300 mm Mould opening (stroke): 600 mm Maximum daylight between plates: approx 900 mm Screw diameter: 40 mm Injection volume: ~ 204 cm³ (≈185 g PS) in one similar spec sheet Motor power / drive: 18.5 kW drive power (pump drive) Heating power: around 11 kW

Year of construction: 1990, condition: ready for operation (used), A Reis spotting press for tool and mold making is available. Pressing force: 1000kN, clamping area: 1200mm/1500mm, installation height: 1575mm, max. mold weight: 10000kg, max. tilting plate load: 4000kg, ram stroke: 1450mm, return force: 400kN, hydraulic pressure: 190bar, pneumatic pressure: 5bar. Machine dimensions X/Y/Z: approx. 3200mm/4500mm/4100mm. Documentation available. On-site inspection possible. Prjdpfx Adext Rl Ijned

Condition: ready for operation (used), total length: 9,000 mm, total width: 4,300 mm, total height: 3,050 mm, empty load weight: 190,000 kg, top side rolls hydraulicaly driven 110 HP on top roll Extra top roll included, dia 660 mm Hardened rolls treated with 50-NI-CR-No 7 Clamping force: 1000 ton Conical bending Electro mechanical control Max open between rolls: 205 mm Foundation needed: 10 500 x 5300 x 2400 mm Number of rolls: 4 Roll capacity cold: 3100 x 125 mm Roll capacity warm: 3100 x 180 mm Type: hydraulic Roll dia upside: 850 mm Dia under roll - side rolls: 850 mm - 720 mm Driven rolls: 3 driven rolls Power needed: 230 HP total Pjdpfjxqh S Tox Adnerd

Condition: used, nominal force 100 t Predpfx Adevuk N Tsnsd stroke 320 mm no. of strokes 35 /min distance between columns 360 / 250 mm Distance table/ram, max. stroke up, adjustment up 500 mm table surface area 320 x 450 mm table height over floor 660 mm ram surface 250 x 280 mm spindle diameter 125 mm power capacity 3,0 kW weight 4,5 t Dimensions (WxDxH) 2,0 x 1,6 x 3,1 m only permitted for hot forming work high speed friction screw press with motor, friction screw drive as is where is, WITHOUT putting into operation

Condition: used, Year of construction: 1998, x-travel 1.250 mm y-travel 880 mm z-travel 800 mm control TNC 426 Heidenhain turning speed range - main spindle max. 12.000 min/-1 power capacity - main spindel 15 / 10 kW max. Torque 500 Nm tool taper SK 40 table surface area 1.500 x 1.050 mm max. table load 2.500 kg number of T-slots 10 T-slot - width 18 H7 mm T-slot - distance 100 mm number of toolpositions 30 pos. max. tool diameter 80 mm Predpfx Adjxp Ry Dsnod max. tool-dia with free toolbox 160 mm max. tool length 315 mm max. tool weight 8 kg max. total weight 100 kg rapid traverse ( X / Y / Z ) 15 m/min feed speeds 10.000 mm/min total power requirement 29 kW weight of the machine ca. 16,0 t dimensions of the machine ca. 7,0 x 5,0 x 3,3 m CNC - Machining Center Vertical DECKEL MAHO - DMU 125 T - ICS

Condition: new, Cutting area round 0°: 127 mm Cutting area flat 0°: 125 x 130 mm Cutting area round 45° right: 90 mm Cutting area square 45° right: 90 x 90 mm Cutting area round 60° right: 45 mm Cutting area square 60° right: 45 x 45 mm Vice opening: 130 mm Saw blade dimensions: 1440 x 13 x 0.65 mm Cutting speed: 60 m / min Motor power: 0.55 kW Voltage: 230 V Weight approx.: 25 kg Features: - Saw arm can be tilted up to 60 - Ideal for cutting pipes, profile material and solid material made of VA, iron, etc. - Stable saw arm for low-vibration work - Low-noise due to stable design Prjdjilk Ekjpfx Adnod - Micro limit switch switches off at the end of the cut - Quick-clamping vice for quick and easy workpiece clamping - Precise, adjustable saw blade guide for optimum cutting results - Environmentally friendly, as there is no need to use lubricants and coolants - Ideal for use on construction sites due to its low weight - Underframe optionally available (not included in the scope of delivery) Equipment: - Saw blade 1440 x 13 x 0.65 mm - Material stop - Ergonomic handle Underframe available at an extra charge: 149 Euro net

Condition: used, mileage: 127,420 km, power: 218 kW (296.40 HP), first registration: 11/1989, overall weight: 24,000 kg, fuel type: diesel, color: orange, axle configuration: 3 axles, gearing type: mechanical, total width: 2,500 mm, total height: 3,580 mm, Equipment: crane, RUTHMANN work platform, type: MT 325, lifting height approx. 16.20 m, reach approx. 27.40 m, telescopic boom extension approx. 16.20 m, swivel range 450 degrees, work platform / 1.70 x 1.00 m, load capacity approx. 500 kg, overload protection, 4-way hydraulically extendable and supportable support, differential lock rear axle, central lubrication system, auxiliary drive, standard driver's suspension seat, electrically adjustable exterior mirror on passenger side, pop-up window, ramp mirror, side reflectors, 2 x rotating beacon, reinforced parabolic springs at front + rear, tank approx. 300 liters, vehicle can be covered with advertising and/or labeled Our offer is generally without a new TÜV approval. If a new TÜV approval is required, we would be happy to make you an offer from our partner workshops! The vehicle may have advertising on it and/or labeled. Our general delivery and payment terms apply. Podpovnqzijfx Adnerd We would be happy to provide you with a financing or leasing offer for this property. Please contact us!

Condition: used, Technical details: number of spindles: 11 Stück number of stations: 11 Stück taper: SK 40 air pressure - required: 6 - 7 bar total power requirement: 13 kW weight of the machine ca.: 10,2 t space requirements of the machine approx.: 4,0 x 4,0 x 3,4 m dimensions of machine: 3,4 x 3,45 x 2,9 m dimensions electric cabinet: 2,1 x 0,4 x 1,9 mm Transfermachine (drilling & cutting) Accesssories optional please enquire to this additional position! - workpiece holding turret Ø 1000mm with tool holder for 8 tool clamping stations, self centering clamping chuck jaws between the jaws, max. 20mm chuck jaw stroke ( oil pneumatic circulation) - 11 working stations with Sk40 intake (right 4x Drill-& Mill spindle and 1x mitU-axis , left 4x Drill-& Mill spindle ) - drill unit 8x spindle stroke 125mm, feed 0 - 2 m/min, 164 - 1005 rpm with 12 gears stages - thread cutting unit working stroke 125mm, rotation direction clockwise and counter clockwise, 31,5 - 194 rpm with 12 gears stages - opposite located drill units 8 pieces with SK 40 holder - coolant device with supply - control via switch panel Prsdsu Idw Iopfx Adnjd - with swarf basin L: 1200 x W: 740 x H: 220mm i.D. *

Condition: new, mileage: 15 km, power: 129 kW (175.39 HP), fuel type: diesel, gearing type: mechanical, overall weight: 3,500 kg, loading space length: 4,200 mm, loading space width: 2,200 mm, loading space height: 400 mm, loading space volume: 3 m³, emission class: euro6, color: white, number of seats: 3, Year of construction: 2024, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), navigation system, HIRE PURCHASE * LEASING* FINANCING AT TOP CONDITIONS Iveco Daily 35S18H V 16m3 MY24 Wheelbase 4100 mm, single rear axle Color: WHITE (50105) EURO 6 Engine: 3.0 liters  Maximum power 176 HP (136 kW), maximum torque 440 Nm in the range of 1600 rpm, 4 cylinders in a row, VGT variable geometry turbocharger Gearbox: 6-speed manual Braking system: discs on both axles (ventilated at the front) Electrical installation: 12V, Tires / wheels: 225/ 65 R16C / single rear wheel Prjdpfx Adjvpcu Denjd Front suspension: independent with torsion bar fixed to the vehicle frame line, integrated with a double-acting telescopic shock absorber Rear suspension: rigid Beams, leaf springs with bumpers, stabilizer. Hydraulic, telescopic double-acting shock absorbers Axle pressure: front 2100 kg, rear 2600 kg Driving safety is ensured by the following systems: ESP 9, ASR, ABS, EBD, Hill Holder, MSR, HBA, LAC, TSM, RMI&ROM Above-average equipment: Additionally, the price of the vehicle includes: ? Rear view camera with guide lines ? Steering wheels covered with skin ? Double rear parabolic springs ? Side mirrors for installation 2.35 mm ? Preparation for the tachograph COMFORT PLUS: ? NAVI MY IVECO infotainment system with 10-inch display ? Attack cruise control (ACC) with radar sensor ? Cabin ventilation and heating system with automatic air conditioning ? Padded comfortable driver's seat (3 adjustment levels, lumbar support, armrest) ? Front fog lights ? USB A+C socket on the driver and passenger side ? Full headrests covered with memory foam, Daily logo ? Standing 2-seater passenger bench with folding table, seat belts Construction: Aluminum flatbed Length: Width: Height: 4200mm 2200mm 400mm ATTENTION: EXAMPLE PHOTOS Vehicle available immediately Financing, leasing, hire purchase with top conditions possible Welcome to carmax24 Today you have the opportunity to purchase one of our selected, tested vehicles. Expert-tested and high-quality vehicles ensure high customer satisfaction and have done so since 2008. This is our daily approach, because you as a customer are our number one priority at carmax24

Condition: used, Year of construction: 1991, pressure 125 t distance between columns 2100 mm stroke 1000 mm dayligth 1300 mm Podpfovut D Tjx Adnsrd table surface area 2230 x 1300 mm die cushion capacity 63 t die cushion stroke 60 mm die cushion area 1000 x 900 mm table height over floor 1050 mm ram surface 2100 x 1000 mm feed down 50 mm/sec feed up 50 mm/sec working feed 10 mm/sec oil volume 410 l power requirement 22,0 kW weight 31,0 t required space 3,1 x 1,7 x 5,95 m hydraulic try-out press permitted for manual loading according to the German Safety Regulations (UVV) with oil-hydraulic drive, controllable dependent on pressure/time and way, hydraulic drawing cushion in table and ram, hydraulic ejector in table, ram interlocking, two-hand operation No foundation pit necessary can be offered without putting into operation, with putting into operation in given condition or alternatively with new control Siemens S 7-1500 F

Year of construction: 1997, condition: used, Price: On request Pjdpswh Shvsfx Adnjrd - Year: 1997 - Documentation available: Yes - CE marking present: Yes - CE certificate present: No - Drive system: CNC - Control system brand: Heidenhain - Number of axes [pcs]: 5 - X-axis travel [mm]: 1200 - Y-axis travel [mm]: 880 - Z-axis travel [mm]: 800 - Table length [mm]: 5000 - Tool holder: SK40 - Max. spindle speed [rpm]: 18000 - Options: Digital readout - └ Type of digital readout: Heidenhain Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: new, Undercarriage suitable for the mobile bandsaw MIOTAL® S 125 G Prsdpfx Asw Hxduodnod

Condition: good (used), Klopp high-speed planer Mod 550 with accessories Podpou Dapxsfx Adnord

Year of construction: 2018, condition: used, Technical details: lifting capacity: 0,125 t swival range : 180 ° Pjdou Utmpepfx Adnerd Arm length: 4000 mm arm length:: Säule - Kranhaken: 3850 mm height lower edge cantilever arm: 3000 mm column diameter: Ø 220 mm rotation: 270 ° Dimensions of the crane assembled: LxWxH: 4800 x 1300 x 3250 mm Dimensions of filling container: LxWxH: 1100 x 1000 x 740 mm Column height: 3200 mm Heavy-duty operation = manual with swivel stop Hoist: Hans Hebetechnik load capacity 1000kg; lifting height approx. 2400mm; hook Ø 30mm with rope safety device; travel distance hoist 2700mm; control via pendant control The crane can be moved via the filling container. *

Condition: ready for operation (used), Rexroth MDEMAXX071-12 Motor + GKR04-2MHGR-071C12 Gearbox MNR: 3 842 532 125, SN:170712454, used, normal signs of use, 100% functional, scope of delivery as per photos Prodpfx Adji D Nhzjnjd

Condition: used, Technical details: spindle taper: 40 number of spindles: 9 Stück weight of the machine ca.: 10,0 t total power requirement: 13 (17,5 PS) kW dimensions of machine: LxBxH: 4100x3400x3200 mm dimensions electric cabinet: LxBxH: 2100x350x1900 mm TRANSFER MACHINE DRILL AND THREADCUTTING MACHINE - ROTARY TRANSFER MACHINE with 9x Drill-& Mill Spindles - right 2x Drill-&Mill Spindle from that 1x with U-axis flexible and 1x thread cutting unit with 9 stages flexible - left 2x Drill-&Mill Spindle from that 1x with U-axis flexible and 1x thread cutting unit with 9 stages flexible, such as radial 2x Drill-&Mill spindle and 1x thread cutting unit 9 stages, flexible - workpiece carrier with 8 clamping stations: workpiece holding barrel Ø 1000 mm (oil-pneumatic cycle), clamping station self-centering clamping jaws - Drilling: SK 40 intake; spindle stroke 125 mm; standard feed rate 0 - 2 m/min; RPM at 12 stages with 164-1005 rpm - Drill- and facing unit; SK 40 intake; spindle stroke 90 mm; standard feed rate 0 - 2 m/min; rapid traverse feed rate 7.5 m/min; RPM at 12 stages with 166 - 1020 rpm Pedpju Idwbefx Adnjrd - 3 piece thread-cutting units: SK 40 Intake; Working stroke 125 mm; RPM at 12 stages with 31.5 - 194 rpm; clockwise and counterclockwise - 6 piece opposing drill units: SK 40 intake Equipment: - coolant system with feed - operation through control panel - chip box - counting mechanism - elevated platform with stairs i.D. *

Condition: ready for operation (used), Rexroth MDEMAXX071-12 Motor + GKR04-2MHGR-071C12 Gearbox MNR: 3 842 532 125, SN:170712374, used, normal signs of use, 100% functional, scope of delivery as per photos Prodpfx Adsi D Nh Tonsd

Condition: used, Year of construction: 1964, Technical details: pressure: 125 t stroke: 28 mm number of strokes: 56-225 Hub / Min distance between columns: 1000 mm ram adjustment: 60 mm distance table/ram: 376 mm Table dimensions: B.950xT:720 mm passage opening in table: 400x130 mm height over floor: 1120 mm Prjdpfxju Nfibe Adned ram surface area: 920x540 mm mortise hole in ram: Dm 65 x 120 mm column travel -side: 250 mm total power requirement: 30 kW weight of the machine ca.: 15,5 t dimensions of machine: 3,1x1,34x3,6 m dimensions electric cabinet LxWxH: 0,64x0,22x1,2 m This press is a high-performance press for mass production /series production. - Contains left side a material feed via automatic feed (mechanic) and right side a waste cutter. Feed = 0-200mm, roll width =250mm Partial documentation as a copy available. Machine is not functional and is on sale as is! *

Condition: new, Röhm RPP-125-1 / GA parallel gripper LA82x45 Id.170022 SN:B7952 ,unused in opened original box, 100% working, scope of supply according to photos Prjdpfx Adji Ec Duonjd

Condition: used, Technical details: number of spindles: 9 Stück total power requirement: 83,0 kW weight of the machine ca.: 17,0 t TRANSFERAUTOMAT with 9x drill-and mill spindles - right 3x drill-& mill spindle, 9 stages, driven, fixed and left 3x drill-& mill spindle 9 stages, driven, fixed such as radial 3x drill-& mill spindle with 9 stages, driven, fixed i.D. Prodpsu Idvkjfx Adnod *

Condition: new, Röhm RPP-125-1 / GA parallel gripper LA82x45 Id.170022 SN:Z6653 ,unused in opened original box, 100% working, scope of supply according to photos Prsdpfxji Ec D As Adnod

Year of construction: 1979, condition: used, Technical details: Flow rate: 400 m³/h Prsdpfsu Nwwqox Adnjd negative pressure : 1250 pa motor: Typ B5-71 mit 2850 U/min connection electric: 380 V total power requirement: 0,37 kW weight of the machine approx.: 35 / 28 kg dimension machine xH: Ø 0,5 x 1,3 m Trockenabscheider mit Ventilator, beide Geräte stehen als Ersatzteilspender zum Verkauf! Nr. 1 = 400 m³/h BJ 1979 (Zustand: Motor i.O., Saugprozess außer Funktion) Nr. 3 = 400 m³/h BJ 1979 (Zustand: unvollständig!) Dry separator with fan Nr. 1 + Nr. 2 (Nr. 1 = 400 m³/h + Nr. 3) Suction nozzle Ø 40 x 50mm Operating temperature 50°. Filter space = approx. Ø 400 x 500m i.D. *

Condition: new, Schunk SRH+40-WP /30061820 Pneumatic swivel unit + 2 x PZN 125-1 / 30043071 Universal gripper, unused, 100% functional, scope of delivery as per photos Prjdpfsi Ec Ngox Adnsd

Condition: used, Year of construction: 1975, Technical details: bore capacity in steel (diameter): 32 mm throat: 230 mm bore stroke: 160 mm spindle taper MT: 3 feed - manual: Handhebel mm revolution per minute: 100...2000 U/min headstock adjustment: 180° Grad headstock traverse: in Höhe/height/altura 350 mm clamping surface area: 1020x615 mm Psdpfxovc Ayto Adnerd height over floor: 860 mm column diameter: 102 mm total power requirement: ca. 1,2 kW weight of the machine ca.: 0,5 t space requirements approx. LxWxH: L:1,2xB:0,77xH:2,26 m equipped: - toothed drill chuck up to 16mm Machine on sale as is, without test run. i.D. *

Condition: used, Technical details: number of spindles: 9 Stück weight of the machine ca.: 10,2 t Transfer machine with 9 Drill-& Mill spindles - right 2x drill -& mill spindle and 1x thread cutting spindle with 9 stages Pjdpfx Aju Idwnodnsrd - left 2x drill -& mill spindle and 1x thread cutting spindle with 9 stages such as radial 2x drill-& mill spinlde flexible and 1x thread cutting spindle 9 stages, flexible i.D. *