Inverter power source for orbital welding machine, welding unit + water cooling, orbital welding equ

MESSER GRIESHEIM - POLYSOUDE PS 204 + RC 200

Condition: used, Power source for orbital welding machine MESSER GRIESHEIM - POLYSOUDE PS204 Knodpfxst Awm De Apmsa Water cooling unit for orbital welding machine MESSER GRIESHEIM - POLYSOUDE RC200 Welding power source, inverter welding machine POLYSOUDE PS 204 + RC 200 Year of manufacture: 1997 Power source serial no.: 9885186 Cooling unit serial no.: 97861? Output: 200 amps = 20% duty cycle 90 amps = 100% duty cycle Power supply: 230 volts, 50 Hz, Schuko plug - Remote control cable type BP 1436 with 7.5 m connection cable - Adjustable output from 1 to 200 amps - DC only - HF ignition - Cooling water unit for torch cooling - 44,895 operating hours (read) - Operating and maintenance manual included Space requirements welding machine (L x W x H): 550 x 360 x 500 mm Space requirements cooling unit (L x W x H): 550 x 360 x 550 mm Weight welding machine: 45 kg Weight cooling unit: 25 kg Good condition Sold without accessories The price refers to a set consisting of 1x power source and 1x water cooler.

Condition: new, functionality: fully functional, Year of construction: 2026, roller (bottom) diameter: 310 mm, roller (top) diameter: 320 mm, roller diameter: 310 mm, roller length: 1,550 mm, working width: 1,500 mm, sheet thickness steel (max.): 38 mm, overall weight: 12,500 kg, total length: 4,500 mm, total width: 2,300 mm, total height: 1,740 mm, power: 18.39 kW (25.00 HP), working length: 1,500 mm, Equipment: documentation/manual, emergency stop, FACCIN HAV 15342 variable three-roll bending machine Electronically controlled, hydraulic three-roll bending machine Technical data: Number of rollers: Three Geometry of the side rollers: variable Working width: 1550 mm Top roller diameter: 320 mm Side roller diameter: 310 mm Pressure force against the top roller: 160 tons Working pressure at nominal force: 250 bar Guaranteed installed power: 18 kW (25 hp) Guaranteed maximum rotation speed: 3.5-7 m/min Guaranteed machine weight: 12,500 kg Length: 4,500 mm Width: 2,300 mm Height: 1,700 mm Guaranteed performance: for material with yield strength 260 N/mm² Rolling capacity (full working width) 38 mm Bending capacity (full working width) 20 mm from pipe diameter 1,600 mm Rolling capacity (full working width) 30 mm Bending capacity (full working width) 17 mm from pipe diameter 415 mm Standard equipment: Variable geometry with linear guides for roller movement Extra long folding bearing for increased frame stability Electronic parallelism system EPS Hardened rollers for high wear protection All rollers ground after heat treatment Kedjt Akt Repfx Apmena Siemens S7-HMI PLC control system PGS-CLASSIC control system with Siemens touch panel Hitech hydraulic and electrical package Simultaneous rotation and roller movement Safety ripcord with emergency stop and CE certification Central lubrication Water cooling for the hydraulics Cone bending device Prepared for retrofitting of supports and roller conveyors FACCIN Advantage Package AP

Condition: reconditioned (used), For Sale: EOS P100 – Ready for Immediate Use KNOW WHAT YOU BUY! Fully revised and with warranty! This EOS P100 has been fully inspected and revised, making it ready for immediate use in your production environment. Kjdpfx Asrm Tdwjpmsna Included in the package: • 2 build frames • Set of hoppers Specifications: • Technology: SLS (Selective Laser Sintering) • Material class: Polymers • Compatible materials: PA2200, PA3200, PA2201, Inframotion PA12, TPU, and more. • Build volume: 200 x 250 x 330 mm • Laser type: Synrad 48-3, 30W CO2 laser • Minimum wall thickness: 0.4 mm Consumables Highlight We offer a wide range of plug-and-play materials, fully tested and optimized for use with EOS machines. Our Inframotion PA12 delivers top performance and provides significant cost savings compared to OEM powders, without compromising on quality. Choose our exclusive materials to drastically reduce your operational costs. Included Services: • Transport & Installation: Safe delivery in original EOS packaging and professional installation included. • Warranty & Maintenance Plans: Flexible options tailored to your specific needs. About Inframotion 3D (IM3D) At Inframotion 3D B.V., we specialize in high-quality refurbished EOS SLS machines with comprehensive support. As the only provider offering a complete solution for used EOS equipment, we distinguish ourselves through extensive expertise and unique services. What we offer: • Expert maintenance: Installation, servicing, repairs, and upgrades performed by experienced ex-EOS technicians. • Exclusive materials: Cost-effective, high-quality consumables such as our plug-and-play PA12, specifically designed for EOS machines. • Complete support: From transport to maintenance plans, we handle it all. Trust IM3D for reliable machines, superior materials, and the expertise to optimize your SLS production. Feel free to contact us for more information or inquiries!

Year of construction: 2009, condition: good (used), machine/vehicle number: 120P1109, OFFER 21407 Motorized tank/boiler turning device with rail-mounted chassis Technical data: - Total load capacity, driven + follower unit: 40,000 kg - Load capacity per tank/boiler turning device: 20,000 kg - Workpiece diameter: approx. 500 - 3,500 mm - Axle distance of the support rollers adjustable via trapezoidal screw spindle - Roller diameter: 500 mm - Roller width: 150 mm - Driven unit with drive on both sides - Continuously adjustable rotational speed - Handheld remote control for forward and reverse rotation - Drive: 400 V - Both units are mounted on rail-mounted chassis - Space requirement, driven unit: approx. W 3,800 x H 1,150 x D 1,350 mm - Space requirement, follower unit: approx. W 3,600 x H 1,150 x D 1,350 mm Ksdpfxshcnhmo Apmona - Weight, driven unit: approx. 2,500 kg - Weight, follower unit: approx. 1,800 kg

Condition: good (used), Flat-jaw thread rolling machine, thread rolling machine, segment thread rolling machine, cold forming machine, knurling machine, thread rolling machine -Manufacturer: EWM, flat jaw thread rolling machine knurling machine -Type: unfortunately without type designation -Drive: 4.6/5.8 kW 1435/2890 rpm -Belt drive: 3-way adjustable -Knurling plate: RAA 1.0 -Central lubrication: -Dimensions: 1680/920/H1440 mm -Weight: 1308 kg Kjdpfei Eg Nkox Apmjna

Condition: new, Year of construction: 2025, Bending machine ZB 70/2 M - with foot pedal - with standard roller set - two driven shafts - mecanical adjusting of the center roller - working position horizontal and vertical Kodst Hwfnjpfx Apmsna - shafts are supported by conical bearings - slide bars on the slide -support are exchangeable - shaft diameter: 40 mm - roller diameter: - shaft rpm: 8,5 U/min - voltage: 400V 50Hz 3Ph - drivingmotor: 1,1 kW - adjusting way: 120 mm - weight: 400 kg - dimensions: 900x600x1100 mm

Condition: as good as new (ex-display), Year of construction: 2025, operating hours: 50 h, functionality: fully functional, A welding robot system is for sale with the following contents: Elite Robot CS620 (1750mm range) with programming flange and software Fronius TPSi 500 Positioner rotateZERO 500 with 1800mm x 800mm intermediate frame Knjdpsv Dvllsfx Apmoa Machine frame System is ready for welding immediately

Condition: used, Year of construction: 2019, functionality: fully functional, table length: 8,000 mm, table width: 2,540 mm, overall weight: 8,000 kg, sheet thickness steel (max.): 100 mm, cutting length (max.): 8,000 mm, cutting width (max.): 2,540 mm, drill diameter: 40 mm, FICEP TIPO G25LG - CNC PLATE PROCESSING LINE (DRILLING, MILLING, THERMAL CUTTING) | YEAR 2019 The Ficep Tipo G25LG is a CNC plate processing line for combined drilling, milling, tapping and thermal cutting of steel plates in structural steel fabrication. Built in 2019 - a young machine in its class on the used market. All processes run in a single pass on a rigid double-bridge gantry frame. CONDITION & REFURBISHMENT Refurbished and inspected by a certified technician, ready for operation. - The exact scope of reconditioning varies from machine to machine and is disclosed individually upon serious interest. - Viewing possible by arrangement (machine reconditioned - no demonstration under power). FUNCTION & APPLICATION The vertical mono drilling unit with automatic tool changer (ISO 40) performs drilling, milling, tapping, centre-punching and countersinking. The Hypertherm XPR300 plasma torch and the integrated oxy-fuel cutting unit handle thermal cutting - from thin sheet to heavy plate. The line is operated via the Ficep Pegaso CNC control. Infeed and outfeed roller conveyors with material transfer (8 m each) ensure continuous material flow. Typical applications: structural steel fabrication, steel trading and plant engineering. TECHNICAL DATA - Manufacturer: Ficep | Model: Tipo G25LG | Year: 2019 | Serial number: 36098 - Machine type: CNC plate processing line (drilling / milling / thermal cutting) - Condition: used, refurbished by certified technician - Frame design: double-bridge gantry frame, welded | Machine weight: 8,000 kg - Plate width: max. approx. 2,540 mm, min. 200 mm - Plate thickness: max. 45 mm (plasma cutting), max. 100 mm (drilling) - Drilling heads: 1 (vertical mono drilling unit) | Tool holder: ISO 40 - Max. drilling diameter: 40 mm | Max. drilling/milling depth: 100 mm - Max. spindle speed: 7,000 rpm | Spindle power: 15 kW - Plasma cutting torch (straight): 1 | Plasma source: Hypertherm XPR300 | 300 A - Oxy-fuel cutting unit: included - CNC control: Ficep Pegaso CNC - Processes: drilling, milling (incl. straight/curved slots, Y/J weld-edge preparation), tapping, centre-punching, countersinking, marking, scribing, straight plasma cutting, oxy-fuel cutting On request (to be confirmed bindingly during inspection): processing length, tool magazine stations, min. plate thickness for drilling, min. drilling diameter, pass line height, longitudinal and cross positioning speeds, connected load and machine dimensions. SCOPE OF DELIVERY - 1 x Ficep Tipo G25LG CNC drilling, milling and thermal cutting line (year 2019) - 1 x Ficep Pegaso CNC control - 1 x Vertical mono drilling unit with automatic tool changer (ISO 40) - 1 x Plasma cutting torch (straight) | 1 x Hypertherm XPR300 plasma source (300 A) - 1 x Oxy-fuel cutting unit Knedpeu Dw I Eefx Apmja - 1 x Infeed roller conveyor with material transfer (8 m) | 1 x Outfeed roller conveyor (8 m) - 1 x Extraction system for plasma cutting LOGISTICS & LOCATION Location: Ulft (Netherlands), directly at the German border. Dismantling, transport, installation and commissioning by ASM by arrangement - individually calculated upon request. ABOUT ASM Arendsen Steel Machinery (ASM): specialist for refurbished Ficep structural-steel machinery. Further machines on request. CONTACT / INQUIRY Viewing by arrangement | Price on request. Sale exclusively to commercial customers (B2B).

Condition: good (used), Year of construction: 2008, Universal machining center Machine type: DMG DMU 60 monoblock Control: Heidenhain iTNC 530 Year: 2008 Available after: sofort / now Knjdpfx Apjziy Iqomea SPECIFICATIONS Travel X-Axis: 730 mm Y-Axis: 560 mm Z-Axis: 560 mm B-Axes: ° C-Axis: 0,001° Amount of controlled axes: 5 Spindle speeds: 12.000 rpm Tool: SK 40 Toolchanger Tool capacity: 60 NC rotary table: Ø 600 Table size: 1.000 x 600 mm Max. Table Load: 500 kg Equipment Chip conveyor Internal cooling: bar paper band filter Caliper: Heidenhain TS 649 Roto Clear Tool measurement Chip rinsing pistol Oil mist separator Working mode: 4

Condition: excellent (used), Year of construction: 2000, used Weishaupt burner ----- RGL70 2-A/ ZM Knjdpfx Aoxf Dzyjpmsa year of manufacture: 2000 output: 1,000 - 10,500 kW