Radial drilling machine

Mas U 1000

Condition: used, Year of construction: 2022, HERMLE C650U Spindle hours: about 2,900 h Operating hours: approx. 19,500 h Immediately Available! Control: HDH iTNC640 Travel: X-1050 mm Y-900 mm Z-600 mm clamping surface: 900 mm x 750 mm A-axis: + 115° to - 115° max. table load: 1500 kg Dedpfx Aljz Ntcto Aswc Tool stations: 92 (42 + ZM50) spindle: 20 - 18.000 rpm, 25/42 kW Internal coolant supply (IKZ): 40 bar Automatic cabin roof: Yes probe: M&H Tool breakage control: BLUM suction: Yes Swivel round table: Screw drive in the C-axis, Tandem A-axis drive Spindle mount: HSK-63A

Condition: good (used), Year of construction: 1998, control type: NC control, number of rollers: 4, roller (bottom) diameter: 540 mm, roller (top) diameter: 560 mm, side roll diameter: 420 mm, roller diameter: 440 mm, roller length: 3,100 mm, sheet thickness (max.): 60 mm, overall weight: 45,000 kg, total length: 8,700 mm, total width: 2,900 mm, total height: 3,075 mm, power: 81 kW (110.13 HP), Equipment: cone bending device, documentation/manual, 4 roll plate bender HAEUSLER - VRM-hy MACH-ID 9638 Make: HAEUSLER Type: VRM-hy Year: 1998 Smallest bending diameter 640 mm Pressing force against upper roll 5800 kN Conical bending attachment Central lubrication Dwsdpszbqquofx Al Aec Equipped for change rolls 570 / 500 / 430 mm Rolling width: 3100mm Rolling thickness 3x toproll Ø:50mm Rolling thickness 5x toproll Ø:60mm Rolling thickness prebending: 40mm Top Roll Ø: 560+440mm Bottom Roll Ø: 540mm Side roll Ø: 420mm Number of rolls: 4 Rolling speed: 0-6 Adjustiment lower roll: 0 - 200mm/min. Adjustment side rolls: 0 - 500mm/min. Number of driven rolls: 2 Power: 81kW Length: 8700mm Width: 2900mm Height: 3075mm Weight: 45000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: reconditioned (used), Year of construction: 2001, functionality: fully functional, turning diameter over cross slide: 270 mm, spindle bore: 77 mm, turning diameter: 505 mm, turning diameter over bed slide: 505 mm, center height: 250 mm, center width: 1,500 mm, turning length: 1,500 mm, quill stroke: 180 mm, quill diameter: 80 mm, quill travel distance: 180 mm, total length: 3,095 mm, total width: 1,100 mm, total height: 1,525 mm, spindle speed (max.): 2,000 rpm, spindle speed (min.): 13 rpm, swing diameter over cross slide: 270 mm, metric thread diameter (min.): 1 mm, metric thread diameter (max.): 40 mm, metric thread steps: 29, bed width: 340 mm, Turning diameter in gap: 700 mm, rotational speed (max.): 2,000 rpm, rotational speed (min.): 13 rpm, swing diameter over bed slide: 505 mm, overall weight: 2,400 kg, rapid traverse X-axis: 1 m/min, rapid traverse Z-axis: 3 m/min, quill mount: MK 5, three-jaw chuck diameter: 250 mm, Trens SN500 Classic — Reconditioned Center Lathe, 2001 We offer this fully reconditioned Trens SN500 Classic center lathe, year of construction 2001, completely overhauled by original factory technicians to near-new condition. Machine details Manufacturer: Trens Model: SN500 Classic Year of construction: 2001 Machine type: manual universal center lathe Control type: manual Max. swing over bed: 505 mm Max. swing over cross slide: 270 mm Max. swing in bed gap: 700 mm Distance between centers: 1500 mm Height of centers: 250 mm Spindle nose: BAJONET DIN (ISO702-III) B8 Spindle bore: 77 mm Spindle speed range: 12.5–2000 min⁻¹ (18 gears) Main motor output: 7.5 kW Dwedpfxezndb Ej Al Ajc Max. torque: 1450 Nm Standard toolpost: 4-way toolpost, max. tool size 32×25 mm Tailstock sleeve: MORSE 5, diameter 80 mm, travel 180 mm Metric threads: 29 pitches, 0.5–40 mm Whitworth threads: 38 pitches, 1–80 TPI Machine dimensions (H×WxL): 1525mm ×1100 mm x 3095mm Weight: approx. 2400 kg (without accessories) Included accessories: 3-jaw chuck TOS Svitavy IUS 250/3-2-M1, ø 250 mm, B8 mount 4-jaw chuck Bison 4335-315-8, ø 315 mm, B8 mount Steady rest, ø 10–115 mm, with 3 friction contacts (rolling contacts available as paid option) Follow rest, ø 10–115 mm, with 2 friction contacts (rolling contacts available as paid option) Large steady rest I., ø 110–250 mm, with 3 friction contacts (rolling contacts available as paid option) Reconditioning scope All guideways ground and hand-scraped Spindle ground and reconditioned Tailstock quill ground All new bearings, including spindle bearings New gears New paint finish New plates (speed, feed, and thread charts) Machine is in excellent mechanical condition and ready for immediate use. Available for inspection. Geometric protocol available. Electronic machine manual on USB. For questions or further details, feel free to contact us by message or phone.

Condition: excellent (used), functionality: fully functional, Year of construction: 2000, machine/vehicle number: 3roll 3500x140 mm prepinch, control type: manual, degree of automation: manual, actuation type: hydraulic, controller manufacturer: MG, controller model: MG, number of rollers: 3, roller (bottom) diameter: 880 mm, roller (top) diameter: 950 mm, side roll diameter: 880 mm, roller length: 3,550 mm, working width: 3,500 mm, working height: 3,950 mm, sheet thickness (max.): 140 mm, sheet thickness steel (max.): 175 mm, overall weight: 200,000 kg, total length: 8,800 mm, total width: 5,100 mm, total height: 5,775 mm, power: 200 kW (271.92 HP), input voltage: 380 V, input frequency: 50 Hz, number of digital displays: 2, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, Hydraulic Plate Bending machine planetary pinch pyramid with prebend. model MG35140V 3 roll capacity 3500x140 mm The machine was overhauled in 2024, Capacity : Plate width mm. 3500 Plate thickness mm. 140 Capacity chart in enclosed Tech data: -3 rolls driven hydraulic motorized with axial gear unit on each roll independent -Synchronized hydraulic rotation of the 3 rolls with variable speed. -Planetary design with pre-pinch fully hydraulic -Conical plate bending with hardened contrast pad -Digital position readouts of the bending rolls -Rolls installed on bearings double crown heavy duty -Overload safety hydraulic operation protection of the 3 rolls -High pressure hydraulic power pack with multi-pumps oil feed -Centralized control panel electric on wheels with joysticks and digital readouts -Emergency stop with safety system around the machine working area Rolls surface length mm. 3550 Top roll mm. 950 Side rolls mm. 880 Electric power on hydraulic unit Hp 100 + Hp 100 Voltage 380 Vac / 50 Hz Configuration & accessories installed with the machine -Hardened surface of the 3 rolls -Conical plate bending attachment , rolls tilt with contrast roller type. -Centralized operator panel with directional joysticks electric. Dodeyzim Aspfx Al Aswc -Digital position readout of the bending rolls. -Emergency and safety installations, certified CE -User manuals and instruction books in English -Dimension see layout drw in enclosed

Condition: good (used), Year of construction: 1999, functionality: fully functional, turning length: 3,000 mm, turning diameter: 1,000 mm, spindle bore: 197 mm, Upon request, videos of the machine in operation can also be provided. Maximum turning length: 6000 mm Turning diameter: over cross slide: 1000 mm over bed: 1250 mm Dwedpsyr N N Rsfx Al Ajc Spindle bore: 197 mm Spindle speeds: 0 – 665 rpm Faceplate diameter: 1200 mm Workpiece weight: 15000 kg between centers Motor power: 55 kW / 74 hp 3 gear stages: 1.5-55 / 50-180 / 180-665 rpm Accessories: Sauter 4-position tool turret (rotation defective) Tailstock (hydraulics partially defective, pressure loss) Chip conveyor 2 chip guard doors (incl. safety device) 4-way bed machine (flat bed) LED lighting

Condition: good (used), Rotary vane booster pump Manufacturer: Leybold Type: RUVAC RA 9001 Condition: Overhauled and available as tested and serviced Dwsdpfx Aljd Hh Nve Ajc Includes: New paint job, motor relubrication, electrical inspection Warranty: up to 12 months Delivery time: in stock

Condition: used, Year of construction: 2009, faceplate diameter 3000 mm swing diameter 3500 mm turning height 3200 mm Control Fanuc type Series 320i Model A slide adjustment 1750 mm ram head dimension 300x300 mm x-axis 2700 mm Table load 30000 kg main drive motor 100 kW Tool changer 16 weight of the machine ca. 89 t dimensions of the machine ca. 8,5x6x8 m No. 1104 The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team Dedpfoyqu Rwox Al Aswc

Condition: good (used), Year of construction: 2016, spindle speed (max.): 3,500 rpm, overall weight: 6,000 kg, Equipment: documentation/manual, rotational speed infinitely variable, Main parameters: Controller: FANUC 0iD/31iA Chuck.: SAMCHULLY 10" Spindle bore: 86mm With jacket tube.:78mm Turret head: 12 main positions 12 secondary positions, BMT65 connection, Programmable hydraulic tailstock: MT5 Main spindle power: 22kW S1max=3500 1/min Living tool power: 5.5kw S2max=5000 1/min X movement range: 260mm Z axis movement range: 830mm Y axis movement range: + - 52mm (104mm) C axis Dedpfjwtg Injx Al Ajwc Maximum turning length: L=760 Largest turning diameter: D=376mm Fast travel speed: 30m/min Automatic tool measurement with probe arm Weight: 6000 kg

Condition: good (used), functionality: fully functional, lifting height: 10 mm, load capacity: 25,000 kg, For sale: Components for hoist P1600 / P2000 Main hoist motor 36/20 K6P P1600/P2000 Fine Gear FG36 Hoist gearbox P1600 / P2000 P2000 housing H20 P1600/ P2000 rope drum H20 P2000 bottom block 4/1, 25t, 20mm rope P2000 rope guide Traverse / sheave - rope pulley All parts in TOP condition Load capacity 25,000 kg / 25 t. Hoist motor 36/20 K6P Fine gear FG 36 Dwjdpfxsv Uvfts Al Ajc 20 hoists available for sale 2-stage trolley travel Fully functional Well below OEM list price

Year of construction: 2002, condition: not inspected (used), Robot no control panel + connection cables Dedsgu U Itepfx Al Aowc Used, untested robot. No technical documentation available. Not tested.