Eccentric press

MA.TE JL21-160

Condition: used, Year of construction: 1970, pressure:63 t throat:250 mm Lhjdpfx Ajcxxx Hjg Rop stroke:8-100 mm table depth:710 mm table width:500 mm ram head dimension:450x280 mm ram adjustment:63 mm no. of strokes:140 Hub/min total power requirement:7 kW weight of the machine ca.:3,5 t

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Table length : 1900 Table width : 1000 Steady arm throath HOR : 670 Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Dimensions (Estimate) Length Ljdskvnumopfx Ag Rehp 3000 mm Width 2200 mm Height 2500 mm Weight 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 Lhedpshlnzksfx Ag Rsp pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Condition: excellent (used), Year of construction: 2011, CNC twin-spindle turning center Control: CNC path control including 19" TFT Siemens Sinumerik 840 D sl solution line with ERGOline control Lodpewcd S Nefx Ag Rjhp and with ShopTurn 3 G TECHNICAL DATA Max. turning diameter 340 mm Spindle distance 1470 mm Turning length 1135 mm Swing over bed 700 mm Swing to tool carrier 2540 mm Travel paths: X1 – Tool carrier I 270 mm Y1 – Tool carrier I 120 mm Z1 – Tool carrier I 1200 mm X2 – Tool carrier II 195 mm Y2 – Tool carrier II 80 mm Z2 – Tool carrier II 1200 mm X3 – Counter spindle slide 180 mm Z3 – Counter spindle slide 1200 mm Main spindle Integrated spindle motor ISM 102 Drive power (100/40% duty cycle) 40/48 kW Torque (100/40% duty cycle) 570/680 Nm Speed range 0-4000 rpm Bar diameter 102 mm Draw tube inner diameter 104 mm C-axis and spindle brake (angular resolution) 0.001° Counter spindle Integrated spindle motor ISM 76 Drive power (100/40% duty cycle) 25/32 kW Torque (100/40% duty cycle) 280/380 Nm Speed range 0-5000 rpm Bar diameter 65/75 mm C-axis (angular resolution) 0.001° Slide 1 Tool carrier (direct drive) Number of tools 12 Tool holder diameter VDI (DIN 69880) 40 mm Maximum power (100/40% duty cycle) 10.9/14.2 kW Maximum torque (100/40% duty cycle) 26/34 Nm Speed range 40 – 10,000 rpm Slide 2 Tool carrier (direct drive) Number of tools 12 Tool holder diameter VDI (DIN 69880) 40 mm Maximum power (100/40% duty cycle) 10.9/14.2 kW Maximum torque (100/40% duty cycle) 26/34 Nm Speed range 40 – 10,000 rpm Slide 3 Rapid traverse speed X/Z axis 30/45 m/min Tool resolution Z axis 0.001° Feed force (40% duty cycle) X/Z axis 16/13 kN EQUIPMENT/ACCESSORIES  IRCO ILS-RBK 100/16 short-bar loader  Various main spindle reducers  NC-controlled workpiece retrieval device from both the main and counter spindles The device consists of an NC-controlled *Horizontal axis *Swivel unit *Vertical axis *2-jaw gripper for interchangeable gripper jaws  Conveyor belt for removing workpieces from the machine  8/20 bar coolant system with immersion cooler  Chip conveyor  Oil mist extraction  Control cabinet cooling unit (up to 40°)  Counter spindle slide  Easy-Tool monitor  1 collet chuck for quick-change clamping head size 100 for the main spindle  1 collet chuck for quick-change clamping head size 100, Nova Achsfix for the counter spindle  Approx. 40 various quick-change clamping heads size 100 (complete inventory)  Pneumatic tool changer, ø 100 mm  Approx. 50 various tool holders, fixed and driven (complete inventory)  Mounting elements  Documentation

Condition: as good as new (ex-display), Year of construction: 2021, machine/vehicle number: 06 61 218, Comm. no.: Lg 32821 Single side decoiler BBT ABH 2000/400 exhibition machine, unused machine no.: 06 62 218 year of manufacture: 2021 Technical data load capacity approx. max. 2.000 kg strip width max. 400 mm Coil inner diameter approx. 450 to 520 mm Lodpfxsg U Utvo Ag Rjhp Coil outer diameter max. 1,500 mm Unwinding speed approx. 2 to 15 min.-1 With adjustable drive and loop control via ultrasonic sensor (analog). Drive by frequency-controlled three-phase geared motor. Spreading of the support segments manually by means of hand crank via joints Number of supporting segments 3 Coil side guide via strong limiting arms, clampable. Reel stand in strong box construction as welded design. construction. Additional equipment: Shutdown "belt loop too small" by antenna switch, attached to the column of the bottom housing of the loop control. Infinitely adjustable in height. Tape side guide at the bottom housing of the loop control, by means of lateral guide rods. The passage width is continuously adjustable.

Condition: new, pressing force: 100 t, stroke length: 400 mm, - Cylinder stroke 400 mm - Working width 1010 mm Lsdpogp Dc Rjfx Ag Rohp - Cylinder is movable - Can be operated electrically or manually - Pressure indicator - Emergency stop - 400V

Condition: used, Double column eccentric punching press BLEMA Gotha type PEZ 160-50 MHSY-ES Eccentric press with roller feed ALBA Machine no. No. 88151005 Year of construction 1988 / 92 Pressure force 160 ton. Frame width 970 mm Stand width sideways 560 mm Table size 900 x 900 mm ram surface 900 x 700 mm Tool installation height 560 mm, max. 700 mm Stroke adjustment 8-160 mm Ram adjustment travel 125 mm Stroke rate 25 to 70 strokes/min. Belt width in roller feed max. 400 mm Motor power approx. 15 kW Lodpodzqlvjfx Ag Rshp Mains connection 380 Volt, 50 Hz - Infinitely variable stroke rate via frequency control - Automatic stroke adjustment - ram weight compensation cylinder with compressed air - Hydraulic overload protection in the ram - Pneumatic clutch/brake combination - Central oil lubrication - Precisely guided press ram with oil-lubricated guides - UNIDOR press control - Swiveling control panel - Press and feed control cabinets, together on one platform, adjacent Platform dimensions 3400 x 2250 mm, height without feet 2950 mm Width of the press without feed 2100 mm Depth of the press with drive motor 2300 mm Overall height of the press 4150 mm Weight of punching press approx. 18 tons. For transportation, the drive motor is removed and the machine is placed on its face. In addition: NC roll feed straightening machine ALBA type GGVHY400 Apparatus no. 1405 and 1406, order no. 910708 (year of manufacture 1992) - ALBA PSS 300 feed control - Feed length infinitely programmable from 0.1 to 6500 mm per stroke - Belt thickness at 400 mm width max. 3 mm - Belt thickness for 300 mm width max. 4 mm - Belt cross-section max. 1200 mm2 - Roller drive hydraulically controlled by the feed - Height-adjustable feed unit on the press to adjust the material infeed height - Hydraulic unit opposite - Drag straightener with hydraulic opening and closing Weight of the complete system approx. 24 tons Space required for transport a mega trailer with an internal height of 3 meters and a loading length of 13.6 meters good condition

Condition: used, Year of construction: 1977, pressure 250 t stroke 40 - 190 mm no. of strokes 40 /min throat 500 mm passage to the back 1050 mm dayligth 615 mm table surface area 1380 x 880 mm hole in the table 450 mm Lhsdovuuaiopfx Ag Rsp table height over floor 800 mm ram surface 1200 x 800 mm ram adjustment 125 mm power requirement 22,0 kW Weight 24,0 t dimensions of the machine ca. 2,0 x 2,5 x 3,95 m x m x m permitted for manual loading according to the German Safety Regulations (UVV) with motor, pneumatic clutch/brake combination, hydraulic overload protection in ram, pneumatic counterbalance in ram, motoric ram adjustment, manual stroke adjustment, motoric centralized lubrication, bolster plate, two-hand operation

Condition: good (used), Manufacturer: WEINGARTEN Type: ER 125 Table size: 800x620 mm A small crack is visible on the load-bearing part of the press; it has been used this way for years. !! Ljdpfx Ajn D Ebaeg Rshp

Condition: excellent (used), Year of construction: 2004, with soundproof booth Table surface 1000x550 mm, ram surface 1000x450 mm Lodpei An Ttjfx Ag Rehp