Single Column Press - Hydraulic

MÜLLER CD 63.12.14

Year of construction: 1993, condition: used, TYPE: DEA 400/2000 Year: n.d. MAXIMUM RAM CAPACITY: 400 tons SLIDE STROKE: 1,100 mm MAXIMUM SHUT HEIGHT: 1,600 mm TABLE DIMENSIONS: 2,000 x 1,600 mm FAST STROKE: 650 mm/sec CUSHION CAPACITY: 160 tons CUSHION STROKE: 400 mm HEIGHT ABOVE GROUND: 5,800 mm Guodpfxjihf R Uo Aa Esd DISTANCE BETWEEN UPRIGHTS: 3,400 mm LATERAL WINDOW: 1,600 mm

Condition: used, Year of construction: 1970, machine/vehicle number: 120895, pressure:63 t throat:250 mm stroke:8 - 100 mm no. of strokes:120 Hub/min Guodpfxjfx Hv He Aa Eed table::715 x 500 mm dayligth:330 mm ram adjustment:63 mm clamping plate:700 x 480 mm hole in the table:240 mm Hole in clamping plate:110 mm dimension of ram:450 x 280 mm weight of the machine ca.:5,5 t dimensions of the machine ca.:1,2 x 1,7 x 2,7 m hydraulic tilting single column eccentric press, tilting in 4 steps, opening to rear (325 x 500mm) and below (360x160mm) with central lubrication via hand pump, additional clamping plate 700 x 480 x 850 mm, two-hand operation, foot-trip operation possible, operating-mode selector for adjustment of continuous or single stroke, emergency cut-off, piece counter, various accessories

Condition: excellent (used), Year of construction: 2014, operating hours: 8,900 h, machine/vehicle number: LP50VH2, 1) Technical specifications Press with conveyor Technical data baler: Manufacturer Presona Typ LP 50 VH2 Year of construction 2014 Press power main press 50 tons Specific press force 63 N/cm2 Feed channel 1,500 x 1,100 mm Filling volume 2,7 m3 Theoretic throughput capacity 730 m3/hour Throughput capacity under operating conditions 340 m3/hour Bale size 1,100 x 720 mm, lenght variable Drive power 45 kW Tying system 5-fold, vertical, fully automatic Throughput capacity at a • bulk weight of 30 kg/cbm 8 up to 10 tons/hour • bulk weight of 50 kg/cbm 11 up to 13 tons/hour • bulk weight of 100 kg/cbm 15 up to 22 tons/hour Gjdpfx Aoyrhi Nsa Esud Bale density (paper, newspaper) 400 up to 550 kg/m3 Filling volume hydraulic oil tank 600 l Weight baler 16 tons netto Scope of delivery: Press, electrical cabinet, control panel, chain conveyor The documentation (operating manual, CE declaration, electrical/hydraulic diagram) is complete. Visiting is possible by appointment. We are not responsible for technical information or any errors. Upon request, we can send video materials of the working press

Condition: good (used), Year of construction: 2010, Press brake with max. pressing force of 400 tonnes max. working length 5100 mm max. stroke 365 mm Gujdpfx Ajyh T Sroa Eed 34 kW Total weight 38 tonnes

Condition: new, Year of construction: 2024, pressing force: 175 t, working width: 3,050 mm, A high-performance DURMA press brake type AD-S 30175 is for sale. With its extensive standard equipment and selected options, it is ideally equipped for the demanding tasks involved in metal processing. Standard equipment: Capacity and size: 3050mm x 175 tons Installation height: 530mm Projection: 450mm Stroke: 265mm Axis control: Precise control with 4 axes. Safety systems: Manuel F. AKAS FPSC safety system, CE F.AKAS BVLT light barriers and safety cages provide maximum protection. Backgauge: Servo motor backgauge & linear guide & ball screw system for maximum precision. Tool clamping system: European standard for fast and safe tool changes. Front arms: Movable, supports the handling of different workpiece sizes. Selected options: Godpfxsrx Rkue Aa Eeud Control unit upgrade: SKY 22 - 3D, for even more detailed bending operations and 3D visualization. Crowning: Motorized adjustment, for even more precise bending results. Backgauge: Extended with motorized X, R-axis backgauge (X=650mm), increases flexibility and precision. Quick clamping: Manual quick clamping for more efficient tool changes. This DURMA press brake is ready to support your production with its advanced technology and reliable performance. It is the ideal choice for companies that value precision, efficiency and safety. For more information or if you are interested, please contact us. Don't miss the chance to expand your production capacity with this high-quality machine.

Condition: used, Technical details: pressure: 100 t daylight dimension : table/slide up: 800 mm throat: 360 mm ram stroke: 500 mm ram speed - forward: 200 m/s ram speed - reverse: 200 m/s Table dimensions: 750 x 560 x 90 mm passage inside table: Ø 26 mm clamping surface ram: BxT: 530 x 400 mm mortise hole in ram: Ø 50 mm cylinder diameter: Ø 250 mm height over floor: 720 mm total power requirement: 17,0 kW weight of the machine ca.: 5,5 t dimension machine xH: 1,8 x 1,2 x 3,2 m Guodpfxovc Ax Nj Aa Eed

Year of construction: 1980, condition: good (used), A used, very well-maintained cycle-controlled lathe from Weisser Heilbronn with a SIEMENS control system. Distance between centers 2000 mm Center height 295 mm Swinging diameter over bed 600 mm Swinging diameter over cross slide 260 mm Swinging diameter in the crotch 800 mm Total length of the crotch 375 mm Bed width 450 mm Travel of X-axis 350 mm Travel of Z-axis 1850 mm Spindle nose DIN 55022, size 8 Spindle speed, number 18, 14 – 1400 rpm Spindle bore 71.5 mm Diameter of front bearing 110 mm Feed range 0.01 – 40.95 mm/rev Rapid traverse 8 m/min DC drive 15 kW 400V 50Hz Max. permissible torque on the spindle 2500 Nm Tailstock quill 80 mm Quill stroke 250 mm Internal taper in quill MK 5 Length x width x height Machine weight 5500 kg Accessories: Tailstock Pneumatic three-jaw chuck with replaceable jaws, 315 mm Quick-change tool holder "MULTIFIX" in front of the center, size "C" Four-position turret behind the center Gsdpfx Aaegyy I Ao Ejud Tool holder Coolant system Follow rest, pneumatically actuated Technical data and dimensions: Subject to change without notice. Video conference via WhatsApp possible after scheduling an appointment.

Year of construction: 1993, condition: ready for operation (used), machine/vehicle number: Seriennummer: 9302394, CNC-Control HATASTAR 2000 The press capacity is 500 t or 5000 kN In addition to the machine tools are available Switch Cabinet left X1- + R-/ X2- + R-Axe on round guide Y1- + Y2-Axe hydraulic Upper tool clamping pneumatic sheet metal trace-device Second tow-hands Operation Gsdpfxsd Egc As Aa Esud universal matrice 100x100x5'100 mm knife 280 x 5'100 mm Matrices-central plate, b = 111 mm

Condition: ready for operation (used), Year of construction: 2000, pressure 170 t chamfer lenght 3170 mm distance between columns 2700 mm column arm 420 mm dayligth 470 mm stroke 200 mm ajustment speed 100 mm/sec Gsdpfoxabgpsx Aa Ejud working feed 10.0 mm/sec return speed 100 mm/sec table width 180 mm table height 960 mm oil volume 235 L 0 300 bar controlled axis 6 Anzahl Number of working hours 29.400 h total power requirement 16.5 KW weight of the machine ca. 11910 kg range L-W-H 4025 x 2020 x 2900 mm well-maintained condition (!!) with only approx. 29.400 operating hours - in checked condition - machine video - ?v=APP0HZjMms4 Equipment: - electro-hydraulic CNC press brake - AMADA CNC control "OPERATEUR 2" - 6 axes (X, Y1 + Y2, R, Z1 + Z2) * swiveling operation - front left * tool & program library - CNC-controlled back stop adjustment (X-axis) * adjustment range .. 700 mm - CNC-controlled vertical adjustment of the stop fingers (R-axis) * adjustment range .. 250 mm - CNC-controlled adjustment of the stop fingers left-right (Z1 + Z2) - hand control unit for manual movement of the axes - AMADA manual upper tool clamping system - AMADA Rehfuß upper tools - divided - AMADA Lower tool holder - incl. 1x V die (not complete) - AMADA DIGI PRO - gigital angle measuring system - 1x freely movable double foot switch - side protective device (swinging doors) - rear protective device (swinging door) - EMERGENCY OFF button at the front - Operating instructions (ENG)

Year of construction: 1992, condition: good (used), machine/vehicle number: 03.323.36002, Item No. 22621 Technical Data: - Max. working length 3500 mm - Distance between columns 3050 mm - Max. pressing force 2000 kN - Distance table / ram max. 480 mm - Column overhang 260 mm - Ram stroke approx. 300 mm - Stroke speeds - Downward speed, no load max. 100 mm/sec - Upward speed 80 mm/sec - Downward pressing speed max. 10 mm/sec - Total drive power 25 kW - Space requirement approx. W 4500 x H 3150 x D 2100 mm - Weight approx. 16000 kg - including: - CNC control CYBELEC, renewed in 2008 - Controlled crowning device - Controlled rear backstop with height adjustment 5 - 1000 mm - Hydraulic tool clamping - Upper tool + universal die set - Material supports - Two-hand control panel Gjdpfx Aaeip Niks Ejud