Hydraulic guillotine shears

LVD HST 40/6

Condition: good (used), Year of construction: 1995, For sale is a good used guillotine shear from LVD. This machine was produced in Germany in 1995. guillotine shear LVD HST - C 40/6 Manufacturer: LVD Type: HST - C 40/6 Cutting capacity in steel 6,35 mm Hnjdpfx Aozty E Dep Hst Maximum length 4050 mm Cutting angle 0.5 to 2 ° Cadence 10 to 45 strokes / min 7.5 kW motor Weight 9500 kg

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered Hodpfxjrgzv Ns Ap Hsnt * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: good (used), Year of construction: 1995, roller (top) diameter: 330 mm, sheet thickness (max.): 23 mm, Manufacturer: IMCAR Type: SIHR Year of manufacture: 1995 Extended end for profile bending rolls (Pipe & T-Angle) Central lubrication Digital readout position side rolls Fully hydraulic machine Hydraulic drop end Hardened rolls Hnedewpku Djpfx Ap Hot Specifications Metric US Standard Roll width: 3100 mm Sheet thickness at 3 x top roll Ø: 18 mm Sheet thickness at 5 x top roll Ø: 23 mm Sheet thickness for initial bending: 20 mm Top roll Ø: 330 mm Side roll Ø: 310 mm Number of rolls: 3 Bending speed: 0 - 5 Side roll adjustment: 200 mm/min. Number of driven rolls: 2 Power: 15 kW Dimensions (estimated) Length: 5250 mm Width: 1700 mm Height: 1700 mm Weight: 11900 kg Please note: The information on this page has been provided to the best of our knowledge, and wherever possible, from the manufacturer. The information is given in good faith, but accuracy cannot be guaranteed. Accordingly, it does not constitute representation or contractual terms. We recommend you check all critical details.

Condition: used, Year of construction: 1993, Technical details: Hsdpfou Rni Hox Ap Hsnt sheet width: 3050 mm plate thickness: 6,0 mm distance between columns: 3460 mm no. of strokes: min./max.: 9 / 17 Hub/min back gauge: 750 mm (motorisch) mm cutting angle: 0,5° - 3,0° ° cutting gap adjustment: manuell mm down holder: 18 Stück (hydraulisch) Stück Table dimensions: 380 x 3100 mm total connected load: 7,5 kW weight of the machine ca.: 4,56 t dimensions of machine: L: 3,64 x B: 2,55 x H: 1,58 m Equipment: With side stop L: 1000 × W: 100 × H: 60 mm and stop bar 990 mm, with 8 supports Operation via control panel and foot switch Cutting zone lighting Stroke counter Machine feet *

Condition: like new (used), functionality: fully functional, Year of construction: 2024, control type: CNC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: EVO, controller model: EVO 4 AXIS 15", number of rollers: 4, roller (top) diameter: 300 mm, roller diameter: 300 mm, roller length: 3,100 mm, working width: 3,000 mm, working height: 1,250 mm, sheet thickness (max.): 30 mm, sheet thickness steel (max.): 30 mm, sheet thickness stainless steel (max.): 25 mm, overall weight: 17,000 kg, total length: 5,500 mm, total width: 2,000 mm, total height: 2,100 mm, power: 18.5 kW (25.15 HP), input voltage: 400 V, number of digital displays: 4, warranty duration: 12 months, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, swiveling upper roller, 4roll hydraulic plate bending machine rated capacity 3000x35 mm MODEL MG M3035 , used year 2024 machine as new with warranty included Planetary dual pre-pinch Performance Capacity: Plate width 3000 mm plate thickness rolling 30 mm pre-bend 25 mm minimum rolling diameter ID 350 mm max open width plate feed 3100 mm special top roll reduced size 300 mm to achieve rolling ID 350 mm Power electric motor 18.5kw on hydraulic unit Vac 400/50 -480/60 Installed configuration Hardened rolls high surface strength Conical plate rolling, cone bending Electric console remoted on wheels with joysticks and readout CNC programmable 4 axis controller touch screen 15” Setup virtual infinite rolling programs with teach-in mode and cad/cam operator interface --- Hydraulic motorized driven the central rolls Pre-pinch load adjustable for pre-bend Drop-end top roll front open unloading closed shells Re-rolling system for welded shells calibration. Safety and emergency stop Manuals and schematics machine dimension 5500x2000x2100 mm -weight 17ton --- Additional accessories available with the machine Hnjdpfx Apjy Tbf Ij Hjt See layout drawing in enclosed nr.1 central support hydraulic 2.2 ton capacity to support large shell dia up to 4,5 meters id nr.1 side support hydraulic left side 2.2 ton double arm nr. 1 side support hydraulic right side 2.2ton double arm

Condition: used, Year of construction: 1987, faceplate diameter 3600 mm swing diameter 4500 mm turning height 1850 mm turning speed range 0,6- 50 U/min weight of the machine ca. 72 t verticale turning machine double coloumn - digital scale - double coloumn - 2x ram - movable cross slide Hnjdpfxoyz Db Uo Ap Hjt - extra toolholder (four station) on the side of facing plate

Condition: used, Year of construction: 2001, functionality: fully functional, Press force 85 t, Bending length 2050 mm, Distance between uprights 1750 mm, Control DELEM, Stroke 215 mm, Throat depth 410 mm, Total power 13 kW, Weight 8,750 kg, Machine dimensions 3190 x 2100 x 2375 mm Hnjdpow Imq Refx Ap Hst

Condition: good (used), Year of construction: 2008, Used 6-meter CNC press brake by Amada Type: HFE 400 6 L Capacity: 6100 x 400 tons Stroke: 350 mm Y1, Y2, X1, X2, R1, R2, Z1, and Z2 CNC controlled 9204 operating hours Weight: 36 tons Transport in 2 parts (main frame + separate lower table) Self-adjusting crowning system in the lower table 450 mm mounted on the floor foundation Hodoy T Hltopfx Ap Hont Dismantling and loading included

Condition: excellent (used), functionality: fully functional, Year of construction: 2016, machine/vehicle number: AR200 tube and profile roll, control type: NC control, degree of automation: semi-automatic, actuation type: hydraulic, controller manufacturer: Delsy, controller model: MG Touch Pro 15", pipe diameter (max.): 273 mm, tube wall thickness (max.): 20 mm, bending angle (max.): 200 °, number of axes: 9, working height: 2,200 mm, overall weight: 27,000 kg, total length: 2,850 mm, total width: 2,950 mm, total height: 2,930 mm, power: 29.42 kW (40.00 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, operating pressure: 240 bar, number of digital displays: 6, Equipment: documentation/manual, emergency stop, Profile bending machine model AR200 brand MG srl year 2016 Hjdpfxoyx A Uue Ap Hjnt Capacity chart of the machine in enclosed. Model AR200 Pipe bending roll NR. 2 set of rollers for pipe bending SIZE 159MM - SIZE 139,7 MM Configuration -pyramid dual pinch side rolls independent hydraulic -3 rolls driven hydraulic with gear unit each shaft -side arms left/right side hydraulic move in 3 direction keeping aligned the profile being formed. -Control panel console NC programmable with automatic rolling, touch screen 15” , display the 9 axis of the machine with readout for manual use and fully programmable automatic forming -Electric power supply 3phase 400/50 Vac -40HP -Service manuals and operation books original. Additional set of rollers and tooling available for bending section HEB - IPE -UNP - ANGLE – T -SECTION- TUBULAR- IRON BAR ON EDGE - see capacity chart in enclosed ..

Condition: new, Year of construction: 2025, Oscillating shear machine Cutting length 3100 mm Material thickness, steel: 10 mm Blades for stainless steel Hnodpfx Apslac Drj Hjt Touchscreen control: Cybelec Back gauge: 1000 mm Cutting clearance adjustable via control panel Delivery time: 3 months