Bed type milling machine

FIL FA 160

Condition: good (used), Spindle diameter: 80 mm Spindle nose: SK50 Spindle speeds: 11 - 1000 RPM X-axis movement: 1700 mm Y-axis movement: 1800 mm Z-axis movement: 1800 mm Spindle out (W-axis): 710 mm Table size: 1100 x 900 mm Nlodpsphl Ecofx Afaea Elbo Digital readout: On Y-axis and Z-axis Featured with: - Turning table - Toolholders Spindle engine: 7,5 KW Machine LxWxH: 5100 x 2650 x 3300 mm Machine weight: 10 Ton

Condition: used, Year of construction: 1999, x-travel 12000 mm y-travel 3600 mm z-travel 1500 mm spindle turning speed range 3000 U/min Control: Heidenhain iTNC430 Milling head 2 axes, indexed 2.5° Vertical (Y-axis): 3600 mm Transverse (Z-axis): 1500 mm Longitudinal (X-axis): 12,000 mm Guide rail length: 14,700 mm Guide rail width: 1400 mm Lowest milling position of the spindle nose measured from the floor (head horizontal): 855 mm Low column design 870 x 900 x 2,625 mm: 3,000 kg High stand design 870x900x3,025 mm: 3,500 kg Motor power: 37 kW Mounting: ISO 50/ DIN 69871-A Speeds: 11.7:231:3000 rpm Feed range: 2:2500 mm/min Rapid traverse X-axis: 12000 mm/min Z-Y axis: 15000 mm/min Feed motor power X-axis: 55 Nm Z-axis: 37 Nm Y-axis: 37 Nm Accuracy Positioning accuracy: 0.025 mm Repeatability: 0.015 mm Weight: approx. 42,000 kg Air supply to the machine: 300 L/min at 4.5 bar Nlodpsxwdygefx Afasa NOTE: The clamping plates and chip conveyors are not included in the scope of delivery. However, we can offer you both used and new clamping plates and chip conveyors on request.

Condition: excellent (used), Year of construction: 1988, functionality: limited functionality, machine/vehicle number: 25.05.004, total length: 9,500 mm, total width: 2,250 mm, total height: 2,300 mm, input voltage: 380 V, power: 50 kW (67.98 HP), overall weight: 21,000 kg, empty load weight: 18,000 kg, compressed air connection: 7 bar, Equipment: documentation/manual, Paper size: 730 x 1060 mm, printing area: 710 x 1040 mm Paper thickness: 0.05 mm – 0.5 mm Preset maximum speed (due to simulation of the throw-off time for high-speed presses) is 4,000 sheets per hour, but the machine can operate much faster for commercial jobs. Four-fold central impression cylinder that prints all 4 colors in one gripper closure. 1988 FAG Speedproof with operator console for ink duct and cylinder adjustments, enabling extremely accurate register printing. Attached is the original factory brochure. The machine has been fully dry ice cleaned, and the cylinders are in excellent condition. Offered strictly on an 'as is, where is' basis. Maximum width is 225 cm, maximum height is 230 cm; shipping in a High Cube container is possible. Nlsdpfx Afeuf Sy Aeasa Price is absolutely fixed, based on the removal of easily separated parts which we could sell separately, such as the Mabeg feeder with vacuum belt delivery, and the four-fold Baldwin stainless steel unit—with each color having its own bath, a mixer, and adjustable temperature control, so all four baths can be set to different temperatures and alcohol concentrations. The machine was dry ice cleaned, and it was intended for prominent use in printing electronic paper. However, due to too many initial losses, the project was discontinued. The machine has been with us for 3 years and, due to its size, I want to sell it as quickly as possible. Hence this very low price. It is an excellent machine. If the machine needs to be set up for testing and sampling, this is possible at an additional cost of €10,000, of which €5,000 must be paid in advance as a deposit under agreed conditions. All relevant information can be found in the original FAG folder for the machine, available via this advertisement as a PDF. Technical Data - Printing size max.: 710 × 1040 mm (27.95 × 40.94 in.) - Paper size max.: 730 × 1060 mm (28.74 × 41.73 in.) - Paper size min.: 500 × 700 mm (19.68 × 27.56 in.) - Stock thickness: 0.05 – 0.5 mm (0.002 – 0.020 in.) - Plate size max.: 800 × 1080 mm (31.50 × 42.50 in.) - Plate thickness: 0.25 – 0.5 mm (0.010 – 0.020 in.) - Speed max.: 4,000 sheets/h - Floor space requirement (incl. access to feeder, delivery, and central control desk): 950 × 525 cm (374 × 206.69 in.) - Press height: 230 cm (90.55 in.) - Weight (including paper stacked in feeder and delivery): approx. 18,000 kg (approx. 39,690 lbs) - Total power requirements: approx. 50 kW - Compressed air supply: 6 – 7 bar

Condition: used, Year of construction: 1984, x-travel 2500 mm y-travel 750 mm z-travel 1000 mm table surface area 2550 x 800 mm spindle taper SK 50 control HEIDENHAIN, TNC 150 B Nsdpfxotqqnws Afasla weight of the machine ca. 16 t

Condition: used, Manufacturer: CINCINNATI Njdpfewrpykex Afasla

Condition: used, Year of construction: 1985, x-travel 485 mm y-travel 385 mm z-travel 380 mm table surface area 800 x 460 mm Nsdpfetqqllex Afaola spindle taper SK 40 control CONTOUR 1 spindle turning speed range 50 - 2500 U/min feeds 10 - 1000 mm/min rapid traverse 2 m/min table load capacity 600 kg quill stroke 80 mm total power requirement 7,5 kW weight of the machine ca. 2,0 t dimensions 2,4 x 1,7 x 1,98 m Acc.: vertical head with hydr. tool clamping and quill retraction, solid table, coolant - movement of X/Y/Z also possible via handwheels -

Condition: new, Pit furnace, make VEI type: SCO_EB clear height: 1200mm clear diameter: 1400 mm outer diameter: 2200 mm Nlodpfx Afsg R Snhjaea outer height (lidless): 1650mm outer height (with lid): 2600mm electrically heated: 64,5 kW fan: 5,5 kW connection: 400 V, 50 Hz temperature: max. 750°C

Condition: used, functionality: fully functional, machine/vehicle number: D20E/7694, Offer Number: D20E/7694 Machinetype: multiple wire drawing machine - dry Make: SKET / MILL Type: 8 BLOCK Constr. year: inlet wire diameter: 6,5 mm finished wire diamter: 1,6 mm Nsdpfx Aowi S Ixjfajla number of drafts: 8 diameter of capstan: 550 mm and 650 mm speed -meters/sek: 8-12 Location: Europe

Condition: ready for operation (used), Year of construction: 2020, operating hours: 11,574 h, travel distance X-axis: 1,525 mm, travel distance Y-axis: 762 mm, travel distance Z-axis: 625 mm, total height: 3,235 mm, overall weight: 13,500 kg, product length (max.): 5,000 mm, This 3-axis DOOSAN MYNX 7500 II was manufactured in 2020, featuring a Heidenhain TNC 620 control with a TS 460 probe. It has a table size of 1600 mm by 750 mm and a maximum spindle speed of 12,000 rpm. With dimensions of 5000 × 4050 × 3235 mm and a weight of 13,500 kg, consider the opportunity to buy this DOOSAN MYNX 7500 II vertical machining centre. Contact us for more information. • Table Length: 1600 mm • Table Width: 750 mm • Spindle Taper: ISO 40 dual contact • Maximum Spindle Speed: 12000 rpm Njdex U Dtwjpfx Afajla Dimensions Machine Depth 4050 mm

Condition: excellent (used), Year of construction: 2016, Machining center Make KNUTH Nsdpotiauhofx Afaela Type EcoMill 350 CNC