Sheet Metal Shear

EHT TSS 4-31

Condition: used, Year of construction: 1985, sheet width 3100 mm plate thickness 4.0 mm thickness at "Niro-steel" 2.5 mm cutting angle adjustment 1.0 ° back stop - adjustable 10 - 1000 mm adjustment speed 180 mm/s down holder 21 Stück strokes per minute 18 - 31 oil volume 160 L Control ELGO P8511 column arm 200 mm distance between columns 3050 mm 0 max. 300 bar Dedjxab Tvspfx Ac Hsck voltage 400 V main drive 9.0 kW weight of the machine ca. 4800 kg. dimensions of the machine ca. 3660 x 2070 x 2140 mm from a maintenance workshop Equipment: - electro-hydraulic sheet metal shear "swing cut" - machine frame = all-steel welded construction - ELGO NC control model P8511, control panel at the front left * for positioning the electro-motoric rear stop * target/actual position value input possible * adjustment by three-phase motor via toothed belt - support table with ball rollers * there are recessed grips between the table plates - front finger guard - hydraulically acting sheet metal hold-down device - 1x freely movable foot switch - emergency stop button at the front - movable scrap switch - original operating instructions + circuit diagram Special accessories included: - EHT pneumatic sheet metal holding device for thin sheet metal cuts - 1x EHT extra long side stop 3.000 mm with mm scale & support foot - 1x EHT extra long support arm with 3.000 mm with scale & Support foot - EHT additional support arms with mm scale

Condition: new, Year of construction: 2026, 2-roll driven profile bending machine Hydraulically adjustable top roller Dsdpfxohgiuho Ac Hock Shaft diameter: 40 mm Roller diameter: 152-162 mm Revolutions: 8.5 per min. Top roll adjustment: 120 mm Capacity table: in the attachment Machine available in various versions: Manual adjustment, 3-roll driven etc.

Condition: excellent (used), Year of construction: 1991, functionality: fully functional, travel distance X-axis: 500 mm, travel distance Y-axis: 350 mm, travel distance Z-axis: 120 mm, travel distance W-axis: 450 mm, For sale: Hauser coordinate grinding machine, model S35-400 The machine is in excellent condition and underwent a partial overhaul in 2024 for €15,000. The machine is equipped with 6 high-quality grinding motors, a face motor, and turbines. TECHNICAL DATA Distance between column and spindle: 365 mm Clearance between table and spindle: 485 mm Main spindle diameter: 100 mm X-axis: 500 mm Y-axis: 350 mm Z-axis: 120 mm W-axis: 450 mm U-axis: 5.5 mm Maximum taper grinding: 16° Table size: 600 x 380 mm T-slots: 6 units, 10 mm width, 50 mm spacing Table load capacity: 300 kg Speeds and Tool Holders Speed 22S: 4,500 - 22,500 rpm 45S/45ST: E19 Speed 45S/45ST: 9,000 - 45,000 rpm 80S: F6 Speed 80S: 40,000 - 80,000 rpm T10/T16: Ø 3 mm Speed T10/T16: 100,000 / 160,000 rpm Slot grinding attachment: 2,900 - 34,500 rpm Planetary movement: 5 - 250 rpm C-axis: 0 - 5 rpm X/Y feed: 0 - 1,200 mm/min W-axis feed: 900 mm/min Z-axis feed: 0.5 - 12,000 mm/min MACHINE DETAILS Digital measuring accuracy: 0.001 mm Base deviation: 0.003 mm Power: 7.5 kW Dsdjwtqthjpfx Ac Hjck Compressed air requirement: 20 m³ System pressure: 5 bar Footprint: 3.5 x 4.4 m Machine height: 3.5 m Connection value: 8.3 kVA Weight: 3.1 t EQUIPMENT - Slot grinding attachment - Rotary table, 300 mm diameter - Swivel table, 200 mm diameter - Coolant system - Extraction unit - Very high-quality accessories included Transportation and loading can be arranged across Europe at extra cost upon request. Prices plus VAT. Viewing by appointment is possible. Contact us—our team is happy to assist you. Trade-in or exchange possible! MACHINE PROCUREMENT / SALES PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MORE. Are you looking for a high-quality yet affordable metalworking machine for your production? Or do you want to sell yours? For more information or contact options, visit our website.

Condition: used, Year of construction: 1994, cutting diameter 520 mm saw band length 7239 mm cutting width 1,3 mm Dcodpowm Rm Ijfx Ac Hek Control POSIMOD cutting range - square - 520 x 520 mm feed length 500 mm feed length: multiple 4500 mm min. cut-off length 6 mm length of rest piece min/max 10 / 100 mm cutting speed 20 - 130 m/min dimensions of saw-band 7239 x 50 x 1,3 mm sawing motor 5,5 kW total power requirement 10,0 kW weight of the machine ca. 3,8 t dimensions of machine L x W x H 3,42 x 2,30 x 2,40 m - 2 column guided - Accessories: roller track 2500 mm length, chip conveyor, coolant

Condition: used, Metal band saw Hans Schreiner MBS270, good condition, 1.5 kW, 2450 mm band length, 227 kg Dcsdpowzzgnefx Ac Hek Subject to price changes, errors, printing and typographical mistakes excepted.

Condition: used, Year of construction: 1993, Technical details: sheet width: 3050 mm plate thickness: 6,0 mm distance between columns: 3460 mm no. of strokes: min./max.: 9 / 17 Hub/min back gauge: 750 mm (motorisch) mm cutting angle: 0,5° - 3,0° ° cutting gap adjustment: manuell mm down holder: 18 Stück (hydraulisch) Stück Table dimensions: 380 x 3100 mm total connected load: 7,5 kW weight of the machine ca.: 4,56 t dimensions of machine: L: 3,64 x B: 2,55 x H: 1,58 m Equipment: With side stop L: 1000 × W: 100 × H: 60 mm and stop bar 990 mm, with 8 supports Operation via control panel and foot switch Cutting zone lighting Stroke counter Machine feet Dcodpfxju Rni Hj Ac Hok *

Condition: good (used), Year of construction: 2001, - Manufacturer: IDE - Type: 45/4 - Year of manufacture: 2001 - Monovis Ø45mm 25LD Dcodpouhpiyofx Ac Hok - Right-hand analog control - Screw profile: PVC - 4 heating zones on cylinder - 4 tool heating zones - Motor power: 8.5kW - Up to 60kg/h Good overall condition, very clean machine

Year of construction: 1972, condition: ready for operation (used), Spindle-to-table distance min./max.: 81mm/481mm, counter support spindle center distance: 195mm, spindle head swivel: 360°, milling spindle diameter: 70mm, spindle adjustment: 100mm, headstock adjustment: 300mm, table dimensions X/Y: 480mm/820mm, travel X/Y/Z: 500mm/200mm/400mm, max. workpiece length: 400mm, spindle speed: 1600rpm, feed X/Y: 500mm/min, feed Z: 250mm/min, spindle head swivel: +/-30°, machine dimensions X/Y/Z: approx. 1600mm/2550mm/1700mm, weight: approx. 2300kg. The machine was electrically tested at the end of 2025 and a defect of the emergency stop switch was discovered. Documentation available. On-site inspection is possible. Dedpfx Aex S Rcmoc Heck

Condition: used, sheet width 4080 mm plate thickness 2.0 mm ST Dsdpfx Acsxabc Ro Hjck thickness at "Niro-steel" 0.8 mm Sheet thickness for ALU 2.5 mm cutting angle 1.3 Grad no. of strokes 34 Hub/min distance between columns 4310 mm back stop - adjustable 15.0 - 750 mm table height 820 mm Control ELGO engine output 9.0 kW weight of the machine ca. 3600 kg. range L-W-H 5250 x 2200 x 1400 mm Good condition (!!) Current new price approx. €70,000 Special price upon request The MHSU motor-driven guillotine shear is based on a torsion-free, rigid welded construction and a dynamic, quiet, and powerful gear motor. High static and dynamic rigidity is ensured by robustly dimensioned main components such as the cutter bar, support table, side supports,and the main drive unit. The motor- driven guillotine shear was developed forsheet metal and plastics processing. With these shears, you can effortlessly produce clean cuts in series. Features: - NC robust, motorized swing cut guillotine shears - with ELGO NC control unit * Digital position display of the backgauge * Adjustable from the front right * With target/actual value input * Continuous adjustment across the entire travel range * Limit switch protection - NC motorized material/backgauge - Shatter-proof, torsion-free welded steel construction - Compact and clearly arranged machine design - Support table with recessed grips - 1x hold-down bar - 1x side stop with T-slot and scale - 3x front support arms - 1x freely movable foot switch - Operating instructions Optional accessories included: - Pneumatic sheet metal holding device for thin sheet metal blanks

Condition: used, Year of construction: 1978, sheet width 3100 mm plate thickness 2 mm rear stop 1000 mm cutting angle 1°06 ° no. of strokes 45 Hub/min total power requirement 3,0 kW dimensions of the machine ca. 3600 x 2200 x 1600 mm weight 4500 kg Equipment: - Electric motorized backgauge - With digital ELGO position display Dsdsuagxpepfx Ac Hjck - Manual cutting gap adjustment - 1x side stop with mm scale - 2x support arms - 1x freely movable double foot switch - Front finger guard Special accessories included: - Pneumatic sheet metal holding device for thin sheet metal cuts