Eccentric Press - Single Column

EBU 25 SK

Condition: ready for operation (used), Year of construction: 1970, machine/vehicle number: 5058870, Pressure force: 25 tons Projection: 200 mm Table size: 450 x 600 mm Table adjustment: 240 mm Ram adjustment: 70 mm Stroke adjustment: 4 - 80 mm Number of strokes: 150 / min Drive Motor: 380V 1.1KW Required space: 1600 x 850 x 2000 mm Weight: approx. 1450 kg Nledpsm Uxzusfx Afaea

Condition: excellent (used), Year of construction: 1993, spindle bore: 118 mm, turning diameter over bed slide: 635 mm, turning diameter over top slide: 390 mm, turning length: 2,000 mm, total length: 4,170 mm, total width: 1,960 mm, total height: 1,800 mm, spindle speed (max.): 1,250 rpm, swing diameter over cross slide: 390 mm, bed width: 480 mm, overall weight: 5,200 kg, Centre lathe Nljdpfjyuwwhsx Afaea Colchester 600 - MAGNUM 1250 MACH-ID 9464 Make: Colchester 600 Type: MAGNUM 1250 Year: 1993 FAGOR 2 Axis Dro Feed all directions Conical turning attachment DBC Turning Length: 2000mm Swing over bed Ø: 635mm Swing over cross slide Ø:390mm Swing in the gap Ø: 900mm Gap length: 300mm Spindle bore: 118mm Spindle power: 22kW Bed width: 480mm Tailstock spindle Ø: 95Ø Stroke pinole: 190mm Spindle taper: 6Mk Speeds / ranges: 1250Rpm Length: 4170mm Width: 1960mm Height: 1800mm Weight: 5200kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Table length : 1900 Table width : 1000 Steady arm throath HOR : 670 Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Dimensions (Estimate) Length 3000 mm Width 2200 mm Height 2500 mm Weight Nledpfx Aekvnumofaea 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), functionality: fully functional, Year of construction: 1990, machine/vehicle number: 4ROLL, roller (bottom) diameter: 470 mm, roller (top) diameter: 470 mm, side roll diameter: 420 mm, roller diameter: 470 mm, roller length: 3,050 mm, working width: 3,050 mm, working height: 1,800 mm, sheet thickness (max.): 50 mm, sheet thickness steel (max.): 45 mm, sheet thickness aluminum (max.): 45 mm, sheet thickness copper (max.): 45 mm, overall weight: 43,000 kg, total length: 7,700 mm, total width: 2,410 mm, total height: 2,470 mm, power: 37 kW (50.31 HP), input voltage: 380 V, type of input current: three-phase, working length: 3,050 mm, Equipment: documentation/manual, emergency stop, PLATE BENDING MACHINE FACCIN - 4 ROLL HYDRAULIC 3000 X 40 MM MODEL 4HCI3-35/30 YEAR 1990 PLATE BENDING ROLL LINEAR GUIDEWAYS DOUBLE PINCH PRE-BENDING Machine in good working condition Bending capacity -Plate width : 3000 mm -Rolling plate thickness 40 mm - Prebend thickness 35 mm Rolls dimensions: -Useful length 3050 mm -central rolls upper/lower 470 mm -side rolls left/right 420 mm • Hardening of the 4 rolls high strength surface Njdpfowb Scmex Afajla • 3 rolls driven powered with gear unit with hydraulic motor • Conical bending attachment side rolls tiltable to form cones, contrast pad roller type. • Opening front hydraulic drop-end to unload the closed shell. • Variable speed working roll bending rotation hydraulic speed fast/slow. • Console electric on wheels with centralized commands joysticks and 3 digital readout. • Digital readouts of the rolls position bending and pre-bending repeatability. • Hydraulic tank capacity oil 350 liters – power electric 37 Kw voltage 380 /50 • Dimension 7700 x2410 x H 2470 mm - weight 43000kgs

Condition: good (used), Year of construction: 2000, table width: 1,000 mm, table length: 1,800 mm, ram plate width: 600 mm, total length: 25,000 mm, total width: 27,000 mm, total height: 47,000 mm, overall weight: 43,000 kg, die cushion stroke: 200 mm, Siemens Simatic OP 27 control system Light barrier Sick Nsdjtiwgispfx Afajla Separate control cabinet Ritta Side passages Ground level installation

Condition: used, functionality: fully functional, Year of construction: 2000, working width: 3,050 mm, cutting angle (min.): 0.5 °, cutting angle (max.): 3 °, sheet thickness (max.): 6 mm, back gauge: 750 mm, input voltage: 380 V, overall weight: 4,500 kg, Hydraulic vertical cutting shear Brand: HACO Model: TS 306 Sold by: Casanova Three-phase 380V Year: 2000 Type: Vertical cutting (blade inclination) Njdpoxgdlnofx Afasla Cutting length: 3050 mm Capacity: 6 mm Cutting angle adjustment: 0.5-3 degrees Number of hold-downs: 13 Strokes per minute: 8-14 Squaring arm: 1000 mm Back gauge: 750 mm Motorized back gauge with handwheel for fine adjustment Motor: 7.5 kW Weight: 4500 kg

Condition: good (used), Brand Ercolina Model CE40H3 Year of manufacture 2006 Hydraulic drive Roller diameter Ø 165 mm Shaft Ø 40 mm Tube capacity (thin-walled) Ø 70x1.5 mm min. Ø 700 mm Tube capacity (thick-walled) Ø 2" x 3.2 mm min. Ø 450 mm Angle section capacity 50x50x6 mm min. Ø 400 mm Nlsdpfx Aow Hx Tvofaea Flat bar capacity 50x10 mm min. Ø 250 mm Flat bar capacity (hard edge) 100x15 mm min. Ø 250 mm Box section capacity 50x50x3 mm min. Ø 500 mm Shaft capacity Ø 35 mm min. Ø 250 mm Power 1.85 kW Bending speed 10 rpm.

Condition: used, Technical details: spindle diameter: 130 mm drill depth: 1380 mm x-travel: 2500 mm y-travel: 1600 mm z-travel: 380 mm w-axis: 900 Bohrspindelvorschub mm U-axis: 320 Planschiebervorschub mm control: auf Wunsch tool taper: ISO SK50 revolution per minute: Planschieber:4,5-180 U/min rpm - drive spindle: 4,5-900 U/min feed:: x/y: 5-2000 total power requirement: ca. 40 kW weight of the machine ca.: ca.< 35 + AZusatzeinrichtungen t Nlsdpovr S Uljfx Afasa The machine can be offered in 4 different sales options. Please choose! 1. the machine is in mint mechanical condition. As is/is. 2. the machine as is/is incl. plate field 4000x2000x300mm = stock no. 1101081 3. the machine is newly wired, with new electrical cabinet, digital display, with 4-axis, AC drives from Siemens, axis motors from Siemens (50A/31Nm) with 12 months warranty on all new parts. 4. further additional equipment can be offered as an option. Such as coolant system, chip conveyor, enclosure etc. We should discuss this on the table with your technical staff. i.D. *

Condition: excellent (used), Year of construction: 2012, The Vertical Machining Center enables drilling, milling and cutting operations and cornering within the scope of technical capabilities indicated in the manual in details: plastic, PVC, ABS, methacrylic, polycarbonate, thermoplastic, composite, aluminum. The vertical work table allows for easy feeding and unloading of processed details and reducing the maximum size of the device to the minimum necessary. Tool change with the use of a 10-element magazine located on the side of the device, it enables various works to be carried out without the need to remove the workpiece from the table. Maximum dimensions of the processed detail: X= 4200mm Y= 1600mm Z= 20mm Rapid traverse speed (m/min): X=30 Y=30 Z=15 Set of milling heads T1 and T2: Spindle power (kW) - 3.3 Rotation speed (rpm) - max 18000 Electric spindle with clamp - ER32 Nedpfx Ajmzbr Sefasla T3 Drill Head Assembly: Spindle motor power (W) - 370 Rotation speed (rpm) - max 2800

Condition: new, saw blade diameter 350 mm capacity 90 degrees: round 115 mm capacity 90 degrees: square 95 mm 180 x 95 mm Working height 925 mm saw blade turning speeds 15 - 90 U/min total power requirement 3,0 kW weight of the machine ca. 0,68 t dimensions of the machine ca. 0,8 x 1,0 x 1,85 m Electro-pneumatic, vertical, linear-guided automatic saw for use of HSS saw blades to make series cuts from 60° left to 45° right steel. Nljdpfx Afofg Rlcjaja The machine also works in semi-automatic cycle. CNC machine with multiprocessor and two with MEP control, latest generation controlled axes that make it possible to achieve 1000 with the same material thickness different cutting programs, each with a different cutting length and number of pieces program.