Single Column Press - Hydraulic

Calende Einständerpresse

Condition: refurbished (used), Year of construction: 2018, machine/vehicle number: DF0150, pressing force: 63 t, pressure:63 t passage width:700 mm stroke:500 mm Approx. weight (w/o operational materials):5,1 t Measurements L x W x H:ca. 1500 x1600 x 2995 mm Return Capacity:6 t Engine Output:11 kW Max Working height:700 mm Approaching Speed max. :140 mm/sec Pressure Speed:15 mm/sec. Travel:500 mm Ram plate:600 x 540 mm Ppjdpfx Ajfhcc Ushyor Table size:750 x 600 mm Table height above ground level:850 mm Oil Tank Capacity:150 l Control voltage:24 V Frequency:50 Hz Siemens Control System:S7 1200 Monitor:Siemens 12 Zoll Special feature: When operating at 260bar the machine reaches a pressure level of 70 tons.

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Pedpfx Askvnumohyopr Table length : 1900 Table width : 1000 Steady arm throath HOR : 670 Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Dimensions (Estimate) Length 3000 mm Width 2200 mm Height 2500 mm Weight 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: refurbished (used), Year of construction: 2019, machine/vehicle number: DF0195 - Rev.00, pressing force: 40 t, pressure:40 t passage width:850 mm stroke:500 mm Ppjdpfxjfhcc He Ahysr Weight of machine approx.:ca. 3,8 t dimensions:ca.1300 x 1800 x 3200 mm return capacity:4 t pestle plate:600 x 450 mm table plate:750 x 720 mm table height over floor:850 mm Oil cooling (electric):1,5 kW (max) max. working heidht:700 mm motor capacity:12,7 kW Approaching Speed max. :140 mm/sec pressure speed:15 mm/sec Return Speed:140 mm/sec Oil Tank Capacity:160 l Monitor:WEG - 10 Zoll Siemens Control System:S7 1200

Condition: new, machine/vehicle number: DF0189, pressing force: 500 t, pressure:500 t passage width:1200 mm stroke:400 mm weight of the machine ca.:40 t dimensions:2800 x 1750 x 4350 mm return capacity:50 t :50 kW Max Working height:800 mm :0 - 10 mm Psdpfxofxykas Ahyopr :0 - 10 mm/sec. :400 mm pestle plate:1000 x 1000 mm table plate:1200 x 1200 table height over floor:1200 mm :700 l

Condition: as good as new (ex-display), Year of construction: 2021, machine/vehicle number: 06 61 218, Comm. no.: Lg 32821 Single side decoiler BBT ABH 2000/400 exhibition machine, unused machine no.: 06 62 218 year of manufacture: 2021 Technical data load capacity approx. max. 2.000 kg strip width max. 400 mm Coil inner diameter approx. 450 to 520 mm Coil outer diameter max. 1,500 mm Unwinding speed approx. 2 to 15 min.-1 With adjustable drive and loop control via ultrasonic sensor (analog). Drive by frequency-controlled three-phase geared motor. Psdpfx Asg U Utvshyepr Spreading of the support segments manually by means of hand crank via joints Number of supporting segments 3 Coil side guide via strong limiting arms, clampable. Reel stand in strong box construction as welded design. construction. Additional equipment: Shutdown "belt loop too small" by antenna switch, attached to the column of the bottom housing of the loop control. Infinitely adjustable in height. Tape side guide at the bottom housing of the loop control, by means of lateral guide rods. The passage width is continuously adjustable.

Condition: new, Year of construction: 2019, pressing force: 110 t, pressure:110 t stroke:400 mm weight of the machine ca.:4,5 t dimensions:ca. 1650 x 1150 x 2800 mm return capacity:11 t total power requirement:11 kW Max Working height:500 mm :10 mm :10 mm/sec. speed rapid traverse:10 mm/sec :400 mm pestle plate:600 x 500 mm table plate:800 x 700 mm Table cut-out:150 x 150 mm table height over floor:900 mm :250 l Monitor SIEMENS:7 Zoll Side trim:2.800,- ? Ppjdefxygtopfx Ahysr :4.800,- ? Light barriers front and back:2.400,- ?

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right Ppedpfx Ahshlnzksyjr space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Condition: excellent (used), Kuka Type: KUKA KR 16 R2010 / Control Unit KR C4 / KUKA smartPAD KUKA KR 16 R2010 – Industrial Robot Technical Specifications: Payload: 16 kg Reach: 2010 mm Repeatability: ±0.05 mm Axes: 6 Mounting Types: Floor, ceiling, wall, or angled mounting possible Controller: KUKA KR C4 (standard) Typical Applications: Handling & Assembly Arc Welding Machine Operation Packaging & Palletizing Pjdowb Ef Uopfx Ahyjpr Pick-and-Place Tasks Special Features: Flexible for use in many industrial sectors High precision and reliability Compact design with long reach Condition: Used Scope of Delivery: (See image) (Subject to change and errors in the technical specifications, information is subject to change!) We would be happy to answer any further questions you may have over the phone.

Condition: used, pressure 160 t passage width / mm stroke / mm Working height 800 mm total power requirement 15 kW weight of the machine ca. 11,8 t - Table size: 1000x1000mm - Distance table/ram, large stroke above, gain. above: 800mm extra information Ppjdpfxeiulkqo Ahyjr Removable table

Year of construction: 1993, condition: ready for operation (used), machine/vehicle number: Seriennummer: 9302394, CNC-Control HATASTAR 2000 The press capacity is 500 t or 5000 kN In addition to the machine tools are available Switch Cabinet left Pedpfxod Egc Ao Ahyjpr X1- + R-/ X2- + R-Axe on round guide Y1- + Y2-Axe hydraulic Upper tool clamping pneumatic sheet metal trace-device Second tow-hands Operation universal matrice 100x100x5'100 mm knife 280 x 5'100 mm Matrices-central plate, b = 111 mm