Profile bending machine

AYEL-TECH PK 40 230V

Condition: new, plate thickness 0,8 mm throat 180 mm weight of the machine ca. 22 Kg dimensions of the machine ca. 500 x 450 x 160 mm Flanging machine is equipped with: - Emergency switch Fgodpoht R Hmsfx Akvef - Footswitch - 7 pcs. Roll sets

Condition: new, plate thickness 1,2 mm roll diameter 62 mm throat 100 mm total power requirement 0,75 kW weight of the machine ca. 130 kg dimensions of the machine ca. 1,1 x 0,5 x 1,3 m Fgsdpfx Akjfv H Edovef Flanging machine is equipped with: - Emergency switch - Footswitch - 7 pcs. Roll sets

Condition: new, Year of construction: 2025, Bending machine ZB 70/2 M - with foot pedal - with standard roller set - two driven shafts - mecanical adjusting of the center roller - working position horizontal and vertical - shafts are supported by conical bearings - slide bars on the slide -support are exchangeable - shaft diameter: 40 mm - roller diameter: - shaft rpm: 8,5 U/min - voltage: 400V 50Hz 3Ph - drivingmotor: 1,1 kW - adjusting way: 120 mm - weight: 400 kg Fgodpfx Ast Hwfnskvsf - dimensions: 900x600x1100 mm

Condition: new, table length 1220 mm table width 760 mm table height 910 mm Fedpfexqrhlox Akvogf weight 226 kg

Condition: ready for operation (used), Selling a well-maintained Mikron VC 1000 milling machine due to the purchase of a new machine. Fgjdpfsh Tnpxsx Akvef

Condition: new, Ostas 4-roll round bending machine 4R OHS 2070 x 220 Hydraulic side roller infeed Hydraulic folding bearing Hardened rolls Conical bending device Separate control panel Roller length : 2000 mm Top roller diameter : 220 mm Side roller diameter : 180 mm Total motor power : 4+3 KW Fodpfx Ajtvn D Tskvogf Weight : 4900 kg Dimensions (mm) : 4050 x 1550 x 1470 (L x W x H) Performance data bending: 11 mm with smallest inner diameter (5 x top roll) 9 mm with smallest inner diameter (1.5 x top roller) Bending performance data: 9 mm with smallest inside diameter ( 5 x top roller ) 7 mm for the smallest inside diameter (1.5 x top roller) All bending capacities are calculated on the basis of 250 N/mm2 yield strength Material ( ST 37 - ST 42 structural steel ) Special accessories installed: Infinitely variable rolling speed: NC control:

Condition: new, cutting diameter 235 mm dimensions of saw-band 2645 x 27 x 0,9 mm cutting width 280 x 190 mm cutting speed 45/90 m/min 120 mm 120 mm 190 mm Impact energy 170 mm connected load frequency 400 Volt total power requirement 1,1 kW weight of the machine ca. 290 Kg Fgsdpfx Akjp Scqysvef dimensions 1,2 x 0,8 x 1,2 m Double miter band saw -Miter cuts up to 60° left and 45° right -Vice with quick clamping device -Band tension control -Electr. Automatic cooling

Condition: as good as new (ex-display), Year of construction: 2007, I - beam section - flat steel 50 x 10 mm I-beam section - upend 80 x 15 mm L-beam 50 mm round material 30,0 mm bar material dia. max. 1 1/2" mm bar material - diameter 30,0 mm weight 0,185 t range L-W-H 670 x 530 x 1350 mm square material 40 x 40 x 3 mm pipes 60 x 2,0 mm total power requirement 0,75 kW Demonstration device Equipment: Fgedpfxst U R H Ue Akvjf • Base frame of the machine • Foot switch • Standard-rolls (divided) • Possible to bend horizontally and vertically

Condition: new, pressure 60 t stroke 400 mm daylight longitudinal/sideways 820 x 300 mm Fjdpfxsgg Nn Ss Akvsgf dayligth 900 mm liter capacity 6,5 l feed down 6,1 mm/sec feed up 10 mm/sec Motor output 2,2 kW weight of the machine ca. 0,675 t dimensions of the machine ca. 1,46 x 0,85 x 2,1 m Presses can be operated both by hand and by motor. Cylinders can be moved sideways. Safety valve with cylinder end position. CE marking

Condition: new, Stempel von Wila typ für Trumpf/Safan Darley und alle Abkantpressen verwenden das Wila-Klemmensystem Fgodpfjr Akrasx Akvof