Laser cutting machine

AMADA PROMECAM LC 3015 F1 NT

Condition: ready for operation (used), Year of construction: 1996, pressure 80.0 t chamfer lenght 2550 mm distance between columns 2130 mm column arm 420 mm ajustment speed 100 mm/sec working feed 10.0 mm/sec return speed 80.0 mm/sec stroke 200 mm dayligth 470 mm table width 60.0 mm table height 910 mm Number of working hours ca. 37.102 h total power requirement 9.0 KW weight of the machine ca. 5750 kg range L-W-H 3100 x 2180 x 2540 mm good / well-maintained condition (!!) - Inspected condition - Machine video - ?v=fwdjSiQYq_A Equipment: - CNC electro-hydraulic press brake - OPERATEUR CNC control for 8 axes X1 + X2, Y1 + Y2, R1 + R2, Z1 + Z2 Nedpfx Afoxabnyeaowf - CNC-controlled backgauge adjustment (X-axes) - CNC-controlled vertical adjustment of the stop fingers (R-axes) - CNC-controlled left-right adjustment of the stop fingers (Z-axes) - Freely movable two-hand control & foot switch - Tool crowning - AMADA type - Various tools - CE marking - Side guards (hinged doors) - Rear guards (hinged door) - 2x emergency stop buttons at the front - Operating instructions

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Nwodpfewp Rqfjx Afasf Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: used, Year of construction: 2004, Cast epoxy resin - dry - 3 phase distribution transformer, manufacturer TESAR Italy, year of manufacture 2004, power 2500kVA, voltage ratio 20 (2x±2.5%)/0.4kV, AN-AF (forced ventilation, permanent overload 30%), Dyn11, uk=6%, IP00, standard losses, functional, complete documentation and rutine test report. Nodpfswpb Etex Afaewf

Condition: excellent (used), Year of construction: 2016, Inca Onset X2, 3/4 automized Color configuration: 8 channel printer with four colours (CMYK) 1/12th of the new price !!!!! Printhead status allowing to print at maximum speed with outstanding quality, up to 140 beds per hour/700m² per hour, needs replacement of 60 heads (circa 45.000€) The machine is in excellent shape, serviced by manufacturer since day number one. Annual maintenance done in May 2025. Nedpfx Ajun Swbjfajwf Available: January 2026 As the business expands, Onset X2 provides the capacity to extend the range of jobs companies can handle. The addition of a second set of CMYK delivers even higher productivity - up to 707m²/hr* (equivalent to 138 full-bed sheets/hr) - while an optional six channels can be populated with light cyan (Lc), light magenta (Lm), white (W) and orange (O) to add versatility and superb quality. A choice of uni-directional, bi-directional and super high-quality print modes can be selected depending on the specific job requirements. * Based on an approximate 6 second material handling time. Decomissioning, transport, installation, training and warranty are included (in Europe) For further technical details please refer to enclosed data sheet.

Condition: used, TECHNICAL DETAILS - Number of axes : 4 MILLING SPINDLE - Tool holder type : BT40 BIG PLUS - Spindle power : 26 [kW] - Spindle speeds : 15000 [rpm] LINEAR AXES - Travels on X/Y/Z axes : 560/640/640 [mm] - Rapid traverses rates (X/Y/Z) : 60 [m/min] B ROTARY AXIS - Travel : 360 [°] - Indexing precision : 0.001 [°] TOOL CHANGER - Auto. Tool Changer type : Bras chargeur - Tool magazine capacity : 60 PALLET CHANGER - Pallet changing device type : Rotopalette - Pallet size : 400X400 [mm] - Pallets number : 2 - Maximum weight upon pallet : 400 [kg] - Maximum workpiece diameter : 630 [mm] - Maximum workpiece height : 900 [mm] POWER SUPPLY - Supply voltage : 400 [V] WEIGHT & DIMENSIONS - Machine floor space : 4100X2300 [mm] - Machine height : 2720 [mm] - Machine weight : 11000 [kg] MACHINE HOURS - Number of working hours : 3700 [h] EQUIPMENT - CNC : Fanuc 31 iB Interface : Ethernet / RS232 / USB / PCMCIA - Electronic handwheel - Linear scales - Rigid tapping - 3 colors status lamp - Coolant tank * with high-pressure pump : 25 [bars] * Coolant through spindle Nwedpfx Afjuhbv Soasf * With cabin washing - Chips conveyor : Arrière - Spindle cooling unit - Tool probe - Workpiece probe : Renishaw OMP60

Condition: excellent (used), Year of construction: 2011, Prima Industrie Platino 1530 laser cutting machine only 4300 hours cutting hours Nedpfxsivg Hge Afaowf This Prima Industrie Platino 1530 laser cutting machine 4,0kW CO2 was manufactured in Italy in the year 2011 and installed at the end of 12/2011. PRIMACH 20 L control unit.

Condition: used, Used Trumpf 5axis laser for sale / 3d laser for sale Used Trumpf 5axis laser for sale / 3d laser for sale Nodpefuah Nofx Afajwf Trumpf TLC Cut 5 Year 2006 Fully serviced twice a year by Trumpf Uk Last service January 2019 New vacuum pump fitted – 28/05/19 Hours: Beam on: 14,922 hours Laser on: 59,480 hours 3.2kw Fully serviced. Jigs / cutting beds included. Delivery and installation can be arranged.

Condition: used, Year of construction: 1970, pressure:63 t throat:250 mm Nsdjcxxx Hepfx Afaswf stroke:8-100 mm table depth:710 mm table width:500 mm ram head dimension:450x280 mm ram adjustment:63 mm no. of strokes:140 Hub/min total power requirement:7 kW weight of the machine ca.:3,5 t

Condition: excellent (used), CPM 2000 granulator, 90kW engine Nedpfxswcdpne Afajwf die diameter 410mm We have several pieces

Condition: reconditioned (used), functionality: fully functional, approx. 4.5 m long infeed and centering table Drive via chain from the feed motor Centers the logs in the middle of the rotor Debarking machine VK 26 4 main cutters 4 pre-cutters Nwjdpfx Afju Hmacoaef 30 KW main motor 11 KW feed unit non-driven extraction table Machine workshop checked Machine cleaned and repainted