Wire eroding machine Agie Classic 3

AGIE CHARMILLES Classic 3

Condition: used, Year of construction: 2011, Technical details X travel: 660 mm Y travel: 355 mm Z travel: 455 mm Control: WinMax Main spindle: Max. speed: 10,000 rpm Main spindle drive power: 11 kW Tool holder: SK 40 Work table: Table clamping surface: 760 x 355 mm Tool changer: Number of tool positions: 20 pcs. Tool holder: SK 40 Total power requirement: 14 kW Machine weight: approx. 3.5 t Space requirements: approx. 3.5 x 3.0 x 2.6 m Fedpfx Aexpwy Dea Espd Chip conveyor (screw type)

Condition: good (used), Year of construction: 2008, turning length: 2,000 mm, feed rate X-axis: 3,000 m/min, feed rate Z-axis: 3,000 m/min, HeidenHain ND780 3 Axis dro Variomatic RPM speedrange  Steady rest Multi fix Tool system DBC Turning Length: 2000mm Swing over bed Ø: 830mm Swing over cross slide Ø:420mm Swing in the gap Ø: 1000mm Fpjdpsxf Ey Rofx Aa Eed Gap length: 295mm Spindle bore: 110mm Bed width: 560mm Tailstock spindle Ø: 105Ø Stroke pinole: 225mm Spindle taper: 6Mk Power: 15kW Speeds / ranges: 2000Rpm Feed rate X-Axis: 3000mm/min. Feed rate Z-Axis: 3000mm/min. Workpiece load: 2400 Length: 3700mm Width: 1900mm Height: 1900mm Weight: 5500kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 2004, Technical details: x-travel: 750 mm y-travel: 600 mm z-travel: 520 mm table surface area: D 700 x 500 mm turning speeds: 42.000 1/min tool taper: HSK E50 control: HEIDENHAIN iTNC 530 tool change unit: 60 pos. rapid traverse: 50 m/min table load capacity - central/maximum: 350 kg total power requirement: 50 kVA weight of the machine ca.: 9 t dimensions of the machine ca.: 3,2 x 2,65 x 2,8 m 5-axis simultaneously HSC-machining center, NC-round-swivelling table B-axis 180°, C-axis 360°, chip conveyor, el. handwheel, laser, prepared for 3D touchprobe HEIDENHAIN TS 641 (without touchprobe), mode 4, oilmist suction, spindle chiller, no internal coolant supply, Fjdpfx Ajwzx Nmoa Ejpd approx. 141.300 hours "machine on", approx. 64.500 hours "spindle on" in total machine in good condition (test report available) *

Condition: used, Year of construction: 1965, honing diameter 80 mm stroke 280 mm throat 300 mm total power requirement 6 kW weight of the machine ca. 2,6 t Honing Ø 10 - 100 mm Max. honing depth, approx. 250 mm Max. spindle stroke 260 mm Distance between spindle and column 300 mm Mounting height 1,000 mm Table size 350 x 500 mm Height of table above floor 500 mm Spindle speeds in 2 steps, infinitely variable, approx. 85 - 300 rpm 170 - 600 rpm Stroke speed, infinitely variable, hydraulic 0 - 23 m/min Spindle drive 2 kW Total electrical load 6 kW - 380 V - 50 Hz Weight 2,600 kg Accessories / Special Features * Built-on 2-station tilting table which accommodates 2 workpieces. Mechanical workpiece clamping, using a manual lever. * Hydraulic infeed of the tool. Fedpst Hwupsfx Aa Espd * Switch-off via timer. * Air measuring device (probably). * Honing oil unit. * Various splash shields, etc. Condition : Good. Machine can be inspected under power. Delivery : Ex stock, as inspected. Payment : Net, after conclusion of contract. Thank you for your interest. We have a selection of honing machines available. Please let us know what you need.

Condition: excellent (used), Year of construction: 2004, Clamping force: 35 tons Opening stroke: 200 mm Mould height: 150-300 mm Clamping platen daylight: 350-500 mm Tie bar daylight: 221 mm Mould clamping plattens (b x h) : 342 x 250 mm Ejector stroke: 60 mm Screw diameter: 25 mm Screw stroke: 100 mm Fpjdpfx Aouykh Dea Eed Injection volume: 70 cm3 Shot weight: 59 g Injection pressure: 1040 bar Working hours: 34.748

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, travel distance X-axis: 600 mm, travel distance Y-axis: 855 mm, travel distance Z-axis: 750 mm, rapid traverse X-axis: 70 m/min, rapid traverse Y-axis: 45 m/min, rapid traverse Z-axis: 90 m/min, workpiece weight (max.): 400 kg, total length: 5,680 mm, total width: 3,170 mm, rotary table diameter: 570 mm, overall weight: 15,300 kg, spindle speed (max.): 21,000 rpm, spindle motor power: 39,000 W, spindle nose: HSK-A63, number of slots in tool magazine: 60, tool length: 365 mm, tool diameter: 170 mm, tool weight: 8,000 g, input voltage: 400 V, type of input current: three-phase, Equipment: chip conveyor, documentation/manual, CNC Machining center GROB G350 TECHNICAL CHARACTERISTICS: Year of manufacturing: 2018 CNC control: SIEMENS 840D sl Number of simultaneous axes: 5 Stroke X axis: 600 [mm] Stroke Y axis: 855 [mm] Stroke Z axis: 750 [mm] Rapid traverse rate X axis: 70000 [mm/min] Rapid traverse rate Y axis: 45000 [mm/min] Rapid traverse rate Z axis: 90000 [mm/min] Max. load on table: 400 [Kg] Fjdpfeyff Ivex Aa Ejpd Stroke A axis : swiveling area of rotary table: -185 / +45 [°] B axis swivelling stroke: 360 [°] Table surface Ø: 570 [mm] Spindle type: HSK-A63 Max. spindle speed: 21000 [rpm] Spindle power: 39 [kW] Tool changer magazin number of stations: 60 Max. tool length: 365 [mm] Max. weight of single tool: 8 [Kg] Max. tool diameter: 170 [mm] Rated current: 61 [A] Total power required: 42 [kVA] Supply voltage: 400 [V] Machine dimensions: 5680 x 3170 [mm] Weight: 15300 [Kg] EQUIPMENT INCLUDED: x1 Renishaw OMP60 part probe x1 Electromechanical tool breakage detection device x1 High pressure coolant pump IKZ: 10–80 [bar] x1 Coolant chiller with air-cooled refrigeration unit: 13 [kW] x1 GROB spindle diagnostics (GSD) software option x1 Tool cleaning device x1 Decentralized work area mist collecting system x1 Automatic door setup x1 Chip conveyor x1 Interface for pallet changer x1 Oil skimmer for waste oil collection Machine visible under power in our premises by appointment. Price on request, loading on truck included. Possibility of shipping Worldwide. The information on this page has been obtained by the best of our ability. Therefore, its accuracy can not be guaranteed. Machine similar to Mikron, Hermle, DMG Mori, Mazak, Hedelius, Axa, Chiron, Matec, Reiden, Lagun, Haas, Alzmetall, but also CNC milling, drilling and tapping machines, as well as CNC grinding machines.

Condition: good (used), Year of construction: 2000, operating hours: 83,000 h, clamping force: 350 kN, screw diameter: 25 mm, For sale is an injection molding machine of the Marker Arburg and the type 320S 350-60 Year of construction: 2000 Operating hours automatic: 83000 Screw diameter: 25 mm Clamping force: 350 kN Barrel length: 60 Fpodpfshhuq Asx Aa Eed On request, transport can be organized throughout Europe for an additional charge. Price incl. VAT Machines purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Do you need a high-quality but inexpensive metalworking machine for your production? Or do you want to sell yours? For further information or contact options, please visit our website

Condition: used, Year of construction: 2010, Milling machines Travel distance X: 760 mm Travel distance Y :510 mm Travel distance Z: 610 mm HSC-machines Number of axis: 3 milling machine / machining center Control: Hurco WinMax spindle chuck: SK - A40 spindle revolutions: 12000 rpm table size X: 1020 mm Fpedpfx Aov D U Apea Eod table size Y: 508 mm max. workpiece weight: 1350 kg tool changer: 24 - time input Power : 13,5 kW Torque: 214 Nm Rapid traverse: 35 m/min spindle cooling chip conveyor

Condition: like new (used), functionality: fully functional, How do you do? We are offering used and compatible clamping devices from Erowa. These are suitable for die sinking and milling. Here are some of the available parts: ER-008617 Plug gauge ER-010723 Control mandrel ITS 50 ER-010561 Replacement probe pin ø 2mm ER-010560 Replacement probe pin ø 5mm ER-093992 Square 25 holder C F-Tool holder with square 25 ER-010592 Square 25 Alignment ruler ER-010495 Square 15 alignment ruler ER-129072 Uniplate Collet holder ø 72 ER16-ER50 Fpsdpfovby U Sox Aa Esd Table probe with magnetic base 3D probe ø1-5 Steel pallet ø148mm All parts have been cleaned and checked by us. A functional test was also carried out. Spare parts are available. Do you have any questions? Then please do not hesitate to contact us.

Condition: good (used), Year of construction: 2012, arm reach: 2,696 mm, controller model: KR C4, KUKA Robots Fjdpfx Aotpwxlsa Espd Model: KR 90 R2700 pro Technical data Maximum reach: 2696 mm Rated payload: 90 kg Rated supplementary load, rotating column / link arm / arm: 0 kg / 0 kg / 50 kg Rated total load: 140 kg Pose repeatability (ISO 9283): -/+ 0,06mm Number of axes: 6 Mounting position: Floor Footprint: 830 mm x 830 mm Weight: approx. 1058 kg Axis data Motion range A1: -/+ 185 ° A2: -140 / -5 ° A3: -120 / 155 ° A4: -/+ 350 ° A5: -/+ 125 ° A6: -/+ 350 ° Speed with rated payload A1: 136 ° / s A2: 130 °/ s A3: 120 ° / s A4: 292 ° / s A5: 258 ° / s A6: 284 ° / s Operating conditions Ambient temperature during operation: 10 °C bis 55 °C (283 K bis 328 K) Controller: KR C4