Used Pipe-bending machines for sale (153)

Condition: ready for operation (used), Pipe Bender, Tube Bending Machine, Profile Bending Machine, SHS/RHS Bender, Used Machine Manufacturer: Schwarze-Wirtz Model: Perfect H135 Dimensions: 6115 x 2870 x 1300 mm Bending Capacity: Round tube: Ø 130 mm, bending radius: 500 mm Square tube: 30 mm, radius: 380 mm 45 mm, radius: 500 mm 50 mm, radius: 500 mm 70 mm, radius: 500 mm 90 mm, radius: 500 mm Bending Angle: up to 180° Dcobu Rbewhmv Ujgneg Electrical Specifications: 380 V

Condition: new, This practical helper for any workshop simplifies assembly and welding of tubes at a 90° angle. It also allows machining of different tube diameters with one device. An eccentric shaft ensures that only minimal effort is needed. Dobswhkf Heu Rbgnecg

Condition: ready for operation (used), Drukbuigmachine voor het buigen van buizen met en zonder doorn Buigen onder druk maakt het mogelijk om zeer kleine buigradiussen te produceren (minimale radius 1 x D). Hierdoor kunnen bijvoorbeeld ketelinstallaties met een hoger vermogen in kleinere afmetingen worden geproduceerd. Drukbuigen maakt ook het gebruik van zeer lange buizen mogelijk, omdat er geen doorn nodig is. De buislengtes kunnen achter de machine aan elkaar worden gelast en tot afgewerkte systemen worden gebogen, waardoor er geen paswerk nodig is. Bovendien garandeert drukbuigen de naleving van de voorgeschreven wanddiktetoleranties in de buisbochten volgens VGB. Vergeleken met conventioneel buigen met een doorn is de afname van de wanddikte aan de buitenzijde van de buis bij drukbuigen zonder doorn zeer gering. Bij gebruik van een buigdoorn maakt drukbuigen het mogelijk om bochten te maken uit dunwandige holle legeringsbuizen met zeer kleine buigradiussen (1 x D), omdat door drukbuigen de buitenwand van de bocht wordt ontlast Er zijn veel hulpmiddelen inbegrepen Drukbuigen of drukbuigen doornvrij koudbuigen Max dia tube x thickness: Ø 89 x 5 mm Max bendingradius: 180° Back stop max tubelength: 6000 mm Bending die: yes Debu Rov Sfivebgnjcg

Condition: used, Manual pipe bender, pipe bending device, mandrel bending machine Hand-held pipe bender, hand-held wire bending machine, bending machine Manufacturer: MEWAG Bending capacity: max. Ø 16 mm 1 bending tool Ø 15 mm with 25 mm bending radius 1 bending tool Ø 10 mm with 16 mm bending radius Dsbu Rswhf Hfobgnjcg 1 bending tool Ø 8 mm with 9 mm bending radius 1 bending tool Ø 6 mm with 8 mm bending radius 1 bending tool Ø 5 mm with 8 mm bending radius - Rotating plate with degree markings - Scope of delivery as shown - Wooden box for storage Dimensions L x W x H: 570 x 480 x 145 mm Weight: 43 kg Good condition

Condition: refurbished (used), Year of construction: 2017, 2017 (Refurbished 2021) Unison Breeze 100 Single / Multistacking CNC Tube Bender Debu Rbgjwhv H Aonscg Bending Capacity Ø100 x 2.00mm. Bend Torque 30,000Nm. Servo Controlled Follower 180˚ at 30 CLR. Collet Capacity Ø100mm. Axis Maximum Speed / Feed 500mm/sec. Bend 70˚/sec. Rotation 360˚/sec. Maximum Stacks At Maximum OD = 3. Maximum Bend Radius =40mm. Maximum Bend Angle 200˚. Load Height 1,200mm. Maximum Tube Length 3,100mm. Maximum Tube Length Hitch = 5,700mm. Multi-radius Is Standard. Repeatability And Accuracy = Feed 0.05 / 0.10mm, Bend 0.05 / 0.10mm, Rotation 0.05 / 0.10˚. 480V 3PH. Full Load Current 94A. Approximate Machine Dimensions (W)8,000 x (D)2,000 x (H)2,300mm. S/No. 2792 (2017) 2792B (2021). NOTE: A loading charge of £250 + VAT will be added to the buyers invoice.

Condition: used, Year of construction: 2006, bending angle: 150 °, total length: 3,000 mm, pipe diameter: 35 mm, wall thickness: 3 mm, input voltage: 380 V, 2006 wafios BER35 Dcsbuovftpdj Rbgnog

Year of construction: 1998, Condition: reconditioned (used), Machine is in very good condition. Capacity, Ø mm / 90 x 5 radius, min./max. / 50/400 Bending Rate/Repeatability / 40º/s. ±0.1° Mandrel length 4 000 Weight, kg 10 000 Machine dimensions 6.7 x 1.7 x 1.8 Dcobuoh I Dtwe Rbgneg Engine kW / 40 Length feed 900 mm/sec Tolerance degree 0.05-0.1°/mm Tools: 48.3-50-57-88.9mm

Condition: good (used), Year of construction: 2001, bending radius: 200 mm, pipe diameter: 76 mm, space requirement width: 850 mm, space requirement length: 5,700 mm, space requirement height: 1,150 mm, Pipe insertion length max 4500 mm - electronic 1-axis control - 2-axis measuring system - electronic display of the twist - electronic display of the longitudinal position - twist angle unit with stops - early mandrel retraction - automatic mandrel lubrication with micro-oil dosing Dcsbjwhdrysu Rbgneg Accessories: - incl. bending tool 21.3 / 26.9 / 33.7 / 42.4 / 48.3 / 60.3 / 76.1 mm x 2 D - incl. various mandrels

Condition: ready for operation (used), Year of construction: 2017, Performance range: 20mm-60mm, max. bending angle: 180°+10°, max. bending radius: 150mm, effective length: 3048mm, bending height: 1050mm, max. section modulus: 12.1cm³, bending tolerance: +/-0.1°, operating pressure: 200bar, connected load: 4kW, machine dimensions X/Y/Z: approx. 2000mm/900mm/1200mm, weight: approx. 500kg. Documentation available. On-site inspection is possible. Dsbewg E Dhsu Rbgnocg

Condition: good (used), Year of construction: 1984, well-preserved machine with tools Dcobjwf Updju Rbgneg

Condition: good (used), Year of construction: 1981, machine/vehicle number: 930-311-2, Offer 23247 Technical specifications: - Bending capacity - Pipe at 45 kg / mm² Ø 6 - 48 mm Dcjbu Rswfqm Eebgnog - Max. bending angle 180° - Max. bending radius 145 mm - Drive 400 V / 1.7 kW - Space required approx. W 900 x H 1100 x D 1400 mm - Weight approx. 600 kg - With - Circular pipe saw - Internal and external pipe deburring device - Mandrel bending device approx. 2000 mm - Various bending tools as shown

Year of construction: 1993, Condition: reconditioned (used), year - 1993 / 2020 complete reconditioned with new PLC Management tube diameter max. 100 mm wall thicknes - 10 mm pull up length of tube - 6000 /12000 mm Mandrel pipe bending up to 4 mm pipe wall thickness and pipe bending without mandrel from 5.0 - 10 mm pipe wall thickness Dcobu Rbgoiau Uujneg accuracy of bending angle ± 0,2 ° total power requirement - 50 kW weight of the machine ca. 6 t

Condition: ready for operation (used), Year of construction: 1996, Functionality: fully functional, bending angle: 182 °, bending radius: 400 mm, total length: 7,000 mm, total height: 1,800 mm, total width: 2,200 mm, thorn length: 4,000 mm, overall weight: 16,000 kg, pipe diameter: 127 mm, type of input current: three-phase, wall thickness: 5 mm, feed length Z-axis: 4,000 mm, motor voltage: 400 V, Equipment: documentation/manual, Capacity, Ø mm / 127 x 5 Radius, min./max. / 50/400 Bending speed/repeatability / 40º/s. ±0,1° Mandrel length 4 000 Weight, kg 16 000 Motor kW / 40 Djbsu Rf E Eou Rbgnscg Length feed 900 mm/sec Degree of tolerance 0.05-0.1°/mm Tools: 63 mm

Condition: good (used), Year of construction: 1994, bending angle: 190 °, bending radius: 700 mm, overall weight: 3,300 kg, wall thickness: 11 mm, - CNC control: CNC MMI Multicontrol 2000 - Control system: NCU - PLC: Siemens Simatic S7 - Electrical connection: 400V / 50 Hz / 85 A The machine is fully automatic and equipped with a tool changer. The following tools are available: Pipe Ø 48.3 mm; radius 105 mm Pipe Ø 60.3 mm; radius 120 mm Pipe Ø 63.5 mm; radius 150 mm Pipe Ø 76.1 mm; radius 190 mm Pipe Ø 88.9 mm; radius 222 mm Pipe Ø 114.3 mm; radius 285 mm Pipe Ø 139.7 mm; radius 350 mm Pipe Ø 141.3 mm; Radius 700 mm Pipe diameter 168.3 mm; radius 420 mm There were a few mandrels with a marking directly engraved on them. These had the following specifications: 88.9 x 8 mm; 88.9 x 4.5 mm; 114.3 x 8.8 mm; 139.7 x 8.8 mm; 168.3 x 12.5 mm; 168.3 x 8.8 mm The following outer diameters of the mandrels were measured: 23.2 mm; 32.3 mm; 37.1 mm; 41.5 mm; 59.3 mm; 70.3 mm; 77.7 mm; 80.9 mm; 88.7 mm; 93.2 mm; 94.7 mm; 103.0 mm; 112.8 mm; 118.8 mm; 128.9 mm; 138.5 mm; 147.2 mm; 153.6 mm The accessory package is valued at approximately €150,000 Dsbuewhdrmo Rbgnocg

Condition: used, Year of construction: 2006, Hydraulic driven Roller diameter Ø 165 mm Shaft Ø 40 mm Capacity tube (thin-walled) Ø 70x1.5mm min Ø 700 mm Djbustqcrho Rbgnjcg Capacity tube (thick-walled) Ø 2" x 3.2 Ø 450 mm Capacity angle bar 50x50x6 mm min. Ø 400 mm Capacity strip 50x10 mm min. Ø 250 mm Capacity strip (difficult side) 100x15 mm min. Ø 250 mm Capacity quiver 50x50x3 mm min. Ø 500 mm Capacity shaft Ø 35 mm min. Ø 250 mm Power 1.85 kW Bending speed 10 rpm

Condition: new, Year of construction: 2023, tube bender R2 ZOPF - without bending tooling - with foot pedal and emergency stop - without tooling - control unit - 100 programs of 9 bends each - precise electronic control of C-shaft - manual and automatic bending mode - bending angle and springback angle are programmable by means of a microprocessor Dcsbuedkxkxj Rbgneg - rapid engagement and disengagement of the tooling - scale for counterbending holder - movable - dimensions 930x410x1000 mm - weight 280 kg - motor 1,5 Kw - 400 V 50 Hz 3 ph. - bending radius R55 - R340 mm - bending capacity of tube Ø 5 mm to 60 mm - max. Bending angle of 210 °

Condition: good (used), Year of construction: 1977, machine/vehicle number: 22247, Offered 23250 Technical data: Dobu Rbsv Hzr Nognecg - Bending performance - Pipe at 45 kg / mm² Ø 6 - 48 mm - Max. bending angle 180 ° - Max. bending radius 145 mm - Drive 400 V / 1.7 kW - Space requirement approx. W 900 x H 1100 x D 1400 mm - Weight approx. 600 kg - with - Pipe circular saw - Inside and outside pipe deburring device - Pipe necking device - Without tools

Condition: new, neu ca. 4 Wochen ab Auftragse Italien 10900 € 223.45 € 60 mm 595 mm 363 mm 900 mm 130 kg 10.5 cm³ 60 x 3 mm 2"Gas x 3,91 mm 60 x 4 mm 60 x 2 mm 60 x 4 mm 60 x 4 mm 64 x 4 mm 64 x 4 mm 60 x 4 mm 50 x 4 mm 35 mm 60x30x4 stehend, 60x40x5 mm 300 mm 10 mm 10 mm 1,25 / 2,50 U/min 1.5 kW digital read out for bending angle manual clamping Dcebu Rbeuhdaasgneg material spring back compensation digital read out and zero setting for clamping point 2 speeds overload protection mobile by rolls and handle tools not included

Condition: used, Year of construction: 1986, tube diameter 4-20 mm wall strength 2 mm bending radius min. 10 mm bending radius max. 75 mm bending speed 35 mm/min Dcebu Rbswbi Hcegnog pull up length of tube 2000 mm total power requirement 7,5 kW weight of the machine ca. 1,1 t dimensions ca. 3100x1000x1400 mm

Condition: excellent (used), Year of construction: 2002, N. 1 ELECTRIC – HYDRAULIC PIPE BENDER MOD. SWING – 6 AXIS VGP 3D YEAR 2002 CE EQUIPPED WITH: - SWING EARLY CORE EXTRACTION - SWING RVS310 VARIABLE RADIUS - SWING FRAME EXTENSION - SWING/SWING3 RIGHT-LEFT COUNTER SLIDE - VGP3D SW 3-DIM. PART FACT PROGR. STANDARD CONFIGURATION: - Characteristics, weights, measurements, capacities and performances of the machines are not binding and can be modified without notice. - 6-axis pipe bending machine with right and left bending direction in automatic cycle. - Management of a maximum of 4 + 4 radii. - Different or different diameters or combinations, in programmable automatic cycle with reference stop of the pipe in the clamp and relative pre-closure. - Brushless motors on the X, Y, Z, Q, and R axes. - Air-oil heat exchanger. - Automatic core lubrication. - Core extraction axis with rapid adjustment. - Predisposition for integration into a flexible production system. - Configurable with manual or automatic loading and unloading. - Safety fence with photocell at the access gate - Automatic right and left bending direction. - 4 right tools + 4 left tools without equipment set-up. - 5 controlled axes and electric bending axis. - 4+4 different bending radii in the same cycle for tubes with diameters from 6 to 18 mm. - 2+2 different bending radii in the same cycle for tubes with diameters from 20 to 30 mm. - Creation of particularly complex geometric shapes. - Mixed bending: fixed and variable radius - Interactive three-dimensional graphic programming on touch screen - Analysis of the feasibility of the piece on the video, with automatic verification of any collisions of the machine and the Dcsbu Rbewa T Nrognjg tube. - Automatic simulation of all alternative processing cycles to verify both the feasibility of the piece and the evidence of the optimal cycle in terms of time and costs TECHNICAL DATA TUBE BENDING MACHINE WITH RIGHT AND LEFT BENDING DIRECTION AND INTERACTIVE THREE-DIMENSIONAL GRAPHIC PROGRAMMING. Bending capacity for: round tube R=450 N/mm2: max. 30x2 mm round tube in Ot - Al- Cu: max. 35 mm metal wire: max. 18 mm Internal bending radius (reducible or increaseable on request): min. 22 max. 120 mm Useful length from die center to gripper edge: 1620 mm Useful length from die center to core extractor: 2700 mm X, Y, Z, R axes accuracy: ±0.05 mm/° X-axis positioning speed: 2000 mm/sec (with brushless motor) Y-axis bending speed: 300°/sec (with brushless motor) Z-axis rotation speed: 900°/sec (with brushless motor) Q-axis positioning speed: 800° mm/sec (with brushless motor) R-axis positioning speed: 300°/sec (with brushless motor) Hydraulic pressure: max. 160 bar Noise level: 65 dB (A) Installed power: 12 kW Controlled axes: No. 5 Total weight: 2500 kg Not including matrices

Year of construction: 1990, Condition: good (used), Offer 20191 Year of manufacture approx. 1990, revision 2002 Technical data: Dcjbuohrdmbs Rbgnsg - Bending capacity at 45 kg / mm² up to approx. Ø 25 x 3 mm - Bending angle left + right selectable - Hydr. double sided bending function - Hydr. infeed ° - Drive 400 V / 11 kW - Space requirement approx. W 1750 x H 2200 x D 2300 mm - Weight approx. 1600 kg - with - bending angle adjustment - Hydr. tension - bending tools

Year of construction: 1990, Condition: good (used), machine/vehicle number: 2ß90 522, Technical data: - Bending capacity - steel tube Ø 20 - 60 x 4 mm - stainless steel tube Ø 20 - 50 x 3 mm - max. moment of resistance 6,2 cm - max. bending angle 180 ° - max. radius 125 mm - Bending speed 8 sec - Drive 400 V / 3 kW - Space requirement approx. L 2400 x H 1600 x D 1000 mm - Weight approx. 1400 kg - with - Bending angle control via potentiometer with digital display - 6 times bending angle preselection Dobu Rbgsfndg Eenjcg - Inner + outer pipe deburrer - Bending tools Rx2,5D Ø 38 ; Ø 50 , Ø 65 ;

Condition: good (used), Year of construction: 1993, machine/vehicle number: 588, Offer 25005 Technical data: - Bending performance - steel pipe Ø 20 - 60 x 4 mm - - stainless steel pipe Ø 20 - 50 x 3 mm - max. moment of resistance 6.2 cm - max. bending angle 180 ° - max. radius 125 mm - Bending speed 8 sec Dcobujv E Ig Re Rbgneg - Drive 400 V / 3 kW - Space requirement approx. L 3900 x H 1300 x D 1000 mm - Weight approx. 1400 kg - with - Bending angle control via potentiometer with digital display - Pipe deburring device for inside + outside - Mandrel bending device with bending length up to 3000 mm - Bending tools Rx2.5D Ø 40; 42.4; Ø 48.3; Ø 60.3

Condition: used, Year of construction: 1992, machine/vehicle number: 150258, Offer 24348 Technical data: - Infinitely variable pressure capacity 15 t - Infinitely variable stroke 150 mm - Mandrel bending device up to 6000 mm - Mandrel bending angle 180 ° Djbu Rbjut Uiqjgnjcg - Drive 400 V / 4 kW - Space requirement approx. W 1500 x H 1200 x D 1100 / 7500 mm - Weight approx. 1500 kg - Bending capacity - Bending capacity horizontal bending flat bars 120 x 10 mm - Tube bending ( pressing process ) up to approx. 11/2 " - Mandrel bending up to 42 mm - Bending tools - Tube bending tools Horizontal bending - Mandrel bending tools steel approx. 21.3 R 50 ; 26.9 R 57 ; 30 R 67 ; - 33.7 R 72.5 ; 42.4 R 92.5 ; mm - Mandrel bending tools plastic approx. 10 R 60 ; 12 R 65 + 85 ; 17.2 R 100 - 28 R 65 ; 33.7 R 120 ; 36 R 100

Condition: good (used), Year of construction: 2006, machine/vehicle number: 4806067, Offer 25059 Technical data: - Pipe bending capacity at 45 kg / mm² up to Ø 48 X 3.5 mm - Solid material up to 30 mm Dcsbu Rev Dux Dsbgnjg - Bending angle 0 - 180 ° - Largest average bending radius Rm 225 mm - Smallest inner bending radius Ri 10 mm - Drive 220 V / 1.7 Kw - Space requirement approx. W 400 x H 950 x D 600 mm - Weight approx. 100 kg - with - Bending angle preselection - Digital bending angle display + bending angle fine adjustment - Bending tools, Ø ½“ R 67 mm, Ø 1“ R 67 mm,