Pipe-Bending Machine

SCHWARZE-ROBITECH CN20P

Condition: used, Year of construction: 1961, max. workpiece diameter 100 mm min. workpiece diameter 10 mm workpiece length 1000 mm total power requirement 16 kW weight of the machine ca. 3 t Hodpfxswwl I Ie Apdow dimensions of the machine ca. 0 m The guides have been outdated 10 years ago

Condition: good (used), Year of construction: 1984, Grinding wheelhead: - motor power : 2,2 kW - spindle speeds : 1 000 - 8 000 rpm - spindle inclination (A-axis): -10° up to +27° - setting accuracy 1 min - height adjustment (Y axis) : 130 mm - stroke range (X axis) : 220 mm - oscillation stroke, steplessly adjustable during oscillation : 0-30 mm - oscillation frequency : 30/60 1/min Workhead: - radius setting (Z axis) : 0.01-50 mm - setting accuracy: 0,01 mm - retraction of slide from the grinding to the measuring position : max. 49 mm - cross table, clamping surface : 155 x 205 mm - travel X - Y : each 60 mm - maximum swivelling angle (B axis): 260° - supply voltage : 380 V Hedovmpabepfx Apdew - weight : 1200 kg Accessories/options: - grinding pressure variable - projector fixed in measuring position - 1 cabinet with accessories - different grinding wheels, flanges - coolant tank - documentation Under power in our warehouse.

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Hodjuz If Nepfx Apdew Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: refurbished (used), functionality: fully functional, Löser centerless tube grinding machine - belt grinding machine - polishing machine - Cylindrical grinding machine Centerless tube grinding / polishing machine for workpieces with a minimum length of 1100mm. The machine was built in 1988 and was completely overhauled in 2012. The machine was converted for polishing and then only polished around 10,000 parts. The machine was no longer used after that. During the general overhaul, the motors, bearings and the entire control cabinet with the frequency converters were completely replaced. The machine can be used for both wet grinding and polishing. Wastewater treatment including pumps is not yet available. We can retrofit these for you according to customer requirements. The transport systems (roller conveyors) between the grinding stations must also be retrofitted to suit your workpieces. The machine can process pipe diameters from 10mm to 160mm. The grinding motors / polishing motors have an output of 7,5kW per station. Hedpfxetmqi Ds Apdow The system can be viewed by appointment in our warehouse in D-63128 Dietzenbach.

Condition: used, Year of construction: 1990, machine/vehicle number: 2316-3, Lg.no. 10622 Technical data: - Drilling capacity into solid steel ST 60 28 mm - Drilling capacity GG 25 40 mm - Thread cutting ST 60 M 30 - Thread cutting GG 25 M 40 - Drill spindle holder MK 3 - Spindle diameter 50 mm - Quill stroke 150 mm Hjdpfx Aeu Et Nbopdew - 18 drilling spindle speeds 45 - 2240 rpm - 4 drilling feeds 0.1 - 0.45 mm - min. / max. distance spindle - table 300 / 700 mm - Drilling radius min / max 305 / 1005 mm - Table height 820 mm - Table size 1200 x 600 mm - Drive 400 V / 6 kW - Space requirement approx. W 1300 x H 2800 x D 2300 mm - Weight approx. 1500 kg - with: - Thread cutting device - hydr. columns + boom clamping - Coolant device - Vertical T-slots on the left side of the machine

Year of construction: 2026, condition: new, Picture 1: Offered Set of two load moving skates with 6tonnes capacity each. You can move 12tonnes in total. The skate system is equipped with high quaity polyurethane wheels. other pictures: Hodpfogi Dl Nex Apdew Load moving skates in different sizes from 60-220mm height and capacities between 5 and 220 tonnes. Available as 3-Point, 4-Point, Containerskates, 360° Rotational skates with Polyurethane wheels (for all floors) or Nylon wheels (for flat and smooth floors). Please send us an inquiry with information about the weight and project you have to move. We will then send you a detailed offer. Short delievery times, typicalles in stock. Pictures show a selection.

Year of construction: 1992, condition: good (used), machine/vehicle number: 10-166, OFFER 13467 Technical data: Hodpfxohrm Ius Apdew - Maximum material thickness with a tensile strength of 40 kg/mm²: approx. 3 mm - Shaft diameter: 45 mm - Manual hydraulic adjustment of the upper roller - Electric foot switch - Drive: 400 V / 1.1 kW - Space requirement: approx. W 550 x H 1200 x D 1200 mm - Weight: approx. 180 kg

Condition: used, Year of construction: 2002, turning diameter max. 420 mm turning length 1250 mm control INDEX, C 200-4 D swing diameter 630 mm travel x1 320 mm travel z1 1250 mm travel x2 170 mm travel z2 1250 mm travel x3 320 mm travel z3 1250 mm main spindle speed max. 3000 U/min main spindle drive 53 kW spindle passage 102 mm spindle head DIN 55026 Gr. 11 max. torque on the spindle 675 Nm sub spindle - spindle speed range max. 3000 U/min sub spindle drive 53 kW sub spindle - spindle passage 102 Hjdpot U R Hzsfx Apdsw sub spindle - spindle head DIN 55026 Gr. 11 sub spindle - spindle torque 675 Nm travel sub spindle 1250 mm feed power X1 14000/Z1 14000 N rapid traverse X1 20/Z1 40 m/min feed power X2 8600/Z2 14000 N rapid traverse X2 20/Z2 40 m/min feed power X3 14000/Z3 14000 N rapid traverse X3 20/Z3 40 m/min numbers of turret head positions Rev. 1 = 12 numbers of turret head positions Rev. 2 = 10 numbers of turret head positions Rev. 3 = 12 number of driven tool stations 12 / 10 / 12 speed of driven tools max. 6000 U/min max. torque 36 / 21 / 36 Nm tool taper DIN 69880 tool taper ø 40 x 63 mm total power requirement 120 kW weight of the machine ca. 19 t dimensions of machine L x W x H 5,77 x 2,47 x 2,62 m Accessories: segment bushing chuck HAINBUCH on main spindle, collet chuck HAINBUCH, SPANNTOP SP on sub spindle, various tool holders (also for driven tools), chip conveyor, coolant - all 3 turrets are prepared for coolant through spindle, but the highpressure coolant pump and tank are not with the machine -

Condition: ready for operation (used), Year of construction: 2018, spindle speed (max.): 5,000 rpm, travel distance X-axis: 225 mm, travel distance Z-axis: 605 mm, overall weight: 4,950 kg, controller manufacturer: MAZATROL, controller model: Smooth C, number of axes: 2, Horizontal turning machine manufactured in 2018. This Mazak QUICK TURN 200MA L features a maximum workpiece diameter of Ø 360 mm and a maximum workpiece length of 535 mm. It is equipped with a spindle speed of 5,000 rpm and a turret with 12 VDI positions. If you are looking to get high-quality turning capabilities, consider the Mazak QUICK TURN 200MA L machine we have for sale. Contact us for further details. • Max Workpiece Diameter: Ø 360 mm • Max Workpiece Length: 535 mm Hsdpfsyuyh Ajx Apdsw • Max Bar Capacity: Ø 65 mm • Spindle Nose: A2-6 • Spindle Bore: Ø 76 mm • Turret Tool Station: 12 VDI positions Additional equipment • Chip extractor Technical Specification Counter Spindle Yes Driven Tools Yes

Year of construction: 2004, condition: good (used), A used, well-maintained double miter cold circular sawing machine from KASTO, model: “KASTOdisc A10” - Fully automatic operation - Single cut - Hydraulic clamping cylinders - Central lubrication for saw guides - Coolant system - Documentation Saw blade diameter 350 mm Cutting range: Round 90°/45° 100/100 mm Square 90°/45° 100x100/100x100 mm Rectangle 90°/45° 170x100/130x100 Hjdpfskfvhkex Apdow Shortest remaining piece length in single cut at 90°: 30 mm Shortest remaining piece length in automatic operation at 90°: 260 mm Working height 950 mm Dimensions (W x D x H) 1530x1348x1890 mm Weight 980 kg Further technical data can be found in the PDF document. Technical data and dimensions: Subject to change.