- Year 2007
- Max.size: 1620 x 2050 mm
- Min.size: 500 x 500 mm
- Laminating station with suction belt table and sliding mark for lateral alignment
- Electronically controlled leading edge unit
- Automatic glue supply
- Bar with stripping needle for processing cardboard carrier sheets, from approx. 400g/sqm upwards
- Short set-up times, as all rollers are centrally and parallel adjustable. Due to the short set-up times, the machine is ideally suited for small and medium runs. Already after 2-3 s...
Manufacturer: Billhöfer
Model: FK 76
Bp3akts0ol
year: 1990
Condition: good , different relays and
contactors were always exchanged immediately,
Application rollers renewed and even the drive
motor with gearbox recently completely
overhauled by a specialist.
In production
Price: on request
Has only been used for smaller productions, and has hardly been used in the last few years.
All service agreements have been complied with by the supplier.
The machine must be picked up at the address in Roskilde DK
202sd7ih
1260 x 1620 mm semi-automatic arc arch floor laminating machine, type 134 R 1250 P by 2003. With clamping band.
Manufacturer: mechanical engineering STOCK GmbH, Tannenwald 8, D - 36323 Grebenau Euler village, Germany
Type: 134 R 1250 P
Year of constr.: 2003.08.18
Laminating machine, suitable for laminating displays & packaging, carrier sheets of single - and double-sided covered corrugated board and deck arches made of paper and cardboard.
Technical data:
Sheet width: min. 500 mm, maximum...
Min. Format 21.0 x 29.7 cm
Max. Format: 72 x 102 cm
Max. Speed: 50 m / min.
Sheet feeder: shed
Foil lamination line: thermal lamination
Heater: oil based
Sheet separator: perforation wheel / hot knife
Pile delivery
Switchgear: Operation via display / switch buttons
Hot knife for polyester, polyethylene and structural films
Bozjr9gdph
Perforation wheel for normal OPP thermal films
Cutting unit with controllable winding
A-14 V567A/1650P
Laminating for edge- or register-precise laminating
year 2000
Max.Size: 1640 x 1640 mm
Min.Size: 500 x 500 mm
Carrier bow:
- single face corrugated board, E/B and F flute
- Double-faced corrugated board up to 7 mm thick
Bpax9cjw2g
- Carton from approx. 0.5 mm thickness
Cover sheet: - cardboard from 100-800 g/sqm
Tolerances: approx. +/- 0.5 mm for front and side edge
capacity: up to max. 3000 sheets/h with 2 persons
Front edge feeder:
- Pile height approx. 1800 mm
- Stack weight ...
The machine is a rarely used, hand-loaded laminating machine.
The parameters are follows:
Max. format (mm): 1480x2050
Min. format (mm): 300x350
Vtq7oy
Max thickness (mm): 13
Weight (g/m2): printed media 100-600
basic media Corrugated cardboard A, B, C, E, EB, BC, etc. Flute
Folding Carton max . 450g
Dimensions (mm): 3350x2110x13640
Weight (T): 6,5
The parts of the machine:
Glue part: the application of the glue by help of the adjustable rollers i...
For sale is a D&K laminating system 3210, consisting of feeder "Accu Feed I HS", laminating unit "Laminator 3210" and the sheet separator "Accu III 3210" for single-sided cellophaning of printed sheets.
-Max. Speed: up to 33m/min
-Separation of the sheets by means of a cutter by "flying knife
-Simple roll change
-76mm core holder for rolls up to 3000m length
-Total length of the whole system: 4,5m
-Weight of the whole unit: 1075kg
-Max. paper size: 70 x 100cm
-Min. paper size: 22,5 x 32cm
-Max....
Machine for the finishing of printed sheets. Automatic sheet download. Grooved roller for straightening the printed sheet, grooved roller for straightening the film. Chrome-plated steel cylinder. Sheet size: 540mm x 740mm,
Bk3tvhshtl
minimum sheet size: 297mm x 210mm. The minimum basis weight of the substrate: 115 g/m², the maximum basis weight of the substrate: 400 g/m². Working temperature range: 70ºC- 140ºC. Touchpad.
Semi automatic laminating machine.
Max width 100 cm
Mex lenght 140 cm
Nwm9r
Water based
Min thickness of material, paper, wood, PVC or other 0.08mm
Max thickness of material, paper, board, corrugated of other 80mm
Front lay stoppage of already glue applied paper in order top sheet to be placed.
Delivery belt with pressure cylinder
Suitable for one or two sides lamination on thin & thick materials
Display mounting station
Krmk2roc
For gluing and assembling 2 or 3-part displays.
-Year 2008
- Cutting width: min. 400 mm, max. 2000 mm
- Output: 20-25 cuts per minute possible - with manual system
- without cold glue unit
Working width: 3200mm, working speed: 1.5m/min, operating hours: approx. 350h.
7d20wif0y
Min. Sheet size
Corrugated board: 400 x 400 mm
Sheets: 405 x 405 mm
Stbyv0
Max. Sheet size
Corrugated cardboard: 1415 x 1595 mm
Sheets: 1420 x 1600 mm
TÜNKERS Fully-automatic Sheet Laminating Machine VKM 1650.2
Sheet size: min. 400 x 400 mm, max. 1650 x 1800 mm
Bfo0o7c72c
Output: up to 2800 sheets /hour (depending on size and material)
Machine width: ca. 2850 mm
Cover sheet: min. 100 -120g/m² - max. 800g/m²(material- and size dependent)
Base material: min. 250g/m² - max. 6mm Thickness
- user friendly ( 1 person)
- frond edge accuracy setting: 0-2mm
- laminating accuracy: + / - 0,25 mm
- fast ground-level staple charging and discharging with f...
board laminator consisting of:
(board) gluer, 82 cm width, coldglue
tranportbelt 3m length
rollerpress 82cm width
Oqkbb7utj
offered in "as is" condition
Machines-Fabr.: Nordmeccanica
Machine type: Triplex Combi 1300
Year of construction: 1995/96
Commissioning: April 1996
1) Materials to be coated:
* BOPP 15 µm - 80 µm
* PETP 12 µm - 30 µm
* LDPE, LLDPE 60 µm - 200 µm (40 µm - 200 µm LF)
* OPA 12 µm - 18 µm
* Nylon cast 50 µm - 80 µm
* ALU 9 µm - 40 µm (15 µm - 40 µm LF)
* PP cast 60 µm - 150 µm
* satin paper 40 g - 150 g (LF only)
2) Materials to be laminated:
* PP cast 25 µm - 150 µm
* ALU 7 µm - 40 µm
* LDPE, LLDPE 20 µm - 200 µm
...
Working width: 1000mm, conveyor length: 900mm, max. operating temperature: 220°C, working height: 940-1000mm, length: 4570mm, width: 1580mm, height: 1400mm, weight: 2.5t, machine was scarcely used.
Y70jph0b
max. sheet size 580 x 740 mm
min. sheet size 210 x 210 mm
material weight sheet thickness 105 - 500gsm
speed 30 - 50 m / min.
dimensions 3660 x 1278 x 1780 mm
Bbdg7e8a3o
Stock Laminating
Max.size: 1420x1640 mm
Bi7by0uhoy
Min.Size: 500x500 mm
Max.speed: 8000 Sh/h
S7 - Electric
Deck/carrier sheet: paper and cardboard 120-400 g/m² / from approx.350 g/m² upwards
Mirus Investor
Stacking height: max. 1900 mm incl. pallet
Plate dimensions: 1000x1500mm, connected load: 27kW.
Bda7bxvgms
max. sheet size 1300 x 1100 mm
min. sheet size 350 x 350 mm
laminate precision +- 1,5 mm
speed 6.000 sheet / hour
F0dyyspgi
total power 12 kW
length 12,5 m
weight 6,8 t
STOCK Laminating
Year 1991
Max.speed: 8000 Sh/h
Max. size: 1420 x 1420 mm
Min.Size: 500 x 500 mm
Belt feeder
Paper: from approx. 120 g/qm
Cmwabxysi
Carton: up to approx. 400 g/sqm
Stacking height: max. 1.9 m
Mirus sheet feeder
Press belt
max. sheet size 1060 x 800 mm
min. sheet size 350 x 350 mm
max. speed 80 m / min.
paper thickness 105-500 g/m²
total power 101 kw
Juuwei
total weight 8500 kg
overall dimension 8860 x 2380 x 3000 mm
Stock Laminating
Max.Size: 1260x1260 mm
Min.Size: 500x500 mm
Max.speed: 5000 Sh/h
Year 1986
Bezkeml
Paper: 120 -400 g/qm
Cardboard: 0.6-7.0 mm
Maximum sheet size: 1100 x 1650 mm
Minimum sheet size: 200 mm x 280 mm
8s9egwm3
Minimum weight lower sheet: 250g / m²
Maximum thickness bottom plate: approx. 12 mm
Upper sheet weight: 80-800 g / m²
Year of construction: 1992
Min. size: 40x32 cm
Max. Size: 1120 x 1020 cm
Max. Speed: 10000 sheets/h
Bjpgz7ay3m
Machine hours:23557h
This may be of interest to you
Machineseeker becomes biggest sponsor of the 2nd Bundesliga in Germany
Photo gallery: The World's 10 biggest excavators
10 valuable tricks for buying used machines online
Photo gallery: the 10 strongest forklift trucks in the world
Sample sales contract for used machines in nine languages
Sell now on Machineseeker! Over 180,000 inquiries per month
Didn't find what you were looking for? Please contact our partners for this category :
Dealer for Laminating installations
Dealer for Laminating installations
