Single Column Press - Hydraulic

ZEULENRODA PYE 160 S1M

Condition: excellent (used), Year of construction: 1984, power: 17 kW (23.11 HP), type of input current: three-phase, pressing force: 160 t, stroke length: 500 mm, operating speed: 200 mm/s, reverse speed: 125 mm/s, table width: 900 mm, table length: 630 mm, throat depth: 800 mm, ram plate width: 700 mm, ram plate length: 450 mm, oil tank capacity: 500 l, total length: 22,000 mm, total width: 12,500 mm, total height: 34,500 mm, overall weight: 7,000 kg, operating pressure: 160 bar, installation height: 800 mm, pressure: 250 bar, Hydraulic press PYE 160 S/1M. Year of manufacture: 1984. Manufacturer: VEB Wema Zeulenroda (Germany). The machine has undergone a general overhaul. Specifications: Maximum pressing force: 160 tons. Operating pressure: 16 MPa. Upper table: 700 x 450 mm. Lower table: 900 x 630 mm. Daylight opening: 800 mm. Cylinder stroke: 500 mm. Downward speed: 200 mm/sec. Upward speed: 125 mm/sec. Power requirement: 17 kW. Oil tank capacity: 500 l. Weight: 7000 kg. Height: 3450 mm, Length: 2200 mm, Width: 1250 mm. Machine in very good condition. Inspection and test under power possible. Nsdoqy E I Rspfx Afajcr

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Table length : 1900 Table width : 1000 Steady arm throath HOR : 670 Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Dimensions (Estimate) Ncsdpfx Afjkvnumjaor Length 3000 mm Width 2200 mm Height 2500 mm Weight 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 1985, x-travel 500 mm y-travel 500 mm z-travel 350 mm table surface area 800 x 450 mm spindle taper: ISO 40 quill stroke mm feed - longitudinal/cross mm/min feeds vertical mm/min turning speed range max. 3150 U/min voltage 380 V / 50 Hz power capacity 4 kW weight of the machine ca. 1,7 t dimensions of the machine ca. 2,5 x 2,3 x 2,0 m • HEIDENHAIN TNC 155 - control, • with electrical hand wheel, Ncsdpfxetv Ia Tj Afaor • several tool tapers, • new set of bevel gears,

Condition: new, Year of construction: 2023, pipe drilling machine, inclined drilling machine, automatic drilling machine TDM100, manual, with one drilling head IMMEDIATELY AVAILABLE FROM STOCK + TO BE INSPECTED UNDER POWER - minimum quantity lubrication - manual material clamping - manual feed - max. tube length 3.000mm (option 6.000mm) - positioning accuracy +/- 0,2mm - 10 stops (can be extended as required) - manual insertion and removal of material - drill head swivels +/- 50 - manual 360 degree tube swiveling device - power drilling unit 1 x 2,2 kW - motor speed 295 - 2950 rpm - display speed on touch panel - illumination drilling unit Nsdpelgvkijfx Afaecr - integrated tool cabinet - round tube up to 114mm - square up to 100 x 100mm - flat material up to 100 x 15mm - T-profile up to 100 x 100 x 12mm - L-profile up to 100 x 100 x 8mm - Double post up to 100 x 15mm - Flow drilling up to M12 - Drilling up to Ø 50mm

Condition: as good as new (ex-display), Year of construction: 2021, machine/vehicle number: 06 61 218, Comm. no.: Lg 32821 Single side decoiler BBT ABH 2000/400 exhibition machine, unused machine no.: 06 62 218 year of manufacture: 2021 Technical data load capacity approx. max. 2.000 kg strip width max. 400 mm Coil inner diameter approx. 450 to 520 mm Ncjdpfx Ajg U Utvofajr Coil outer diameter max. 1,500 mm Unwinding speed approx. 2 to 15 min.-1 With adjustable drive and loop control via ultrasonic sensor (analog). Drive by frequency-controlled three-phase geared motor. Spreading of the support segments manually by means of hand crank via joints Number of supporting segments 3 Coil side guide via strong limiting arms, clampable. Reel stand in strong box construction as welded design. construction. Additional equipment: Shutdown "belt loop too small" by antenna switch, attached to the column of the bottom housing of the loop control. Infinitely adjustable in height. Tape side guide at the bottom housing of the loop control, by means of lateral guide rods. The passage width is continuously adjustable.

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right Ncjdshlnzkjpfx Afasr space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Condition: excellent (used), Year of construction: 1975, -KOM 1002-

 Offered here is a press of the company HYDRAP of the type HKPS8000. Technical data: Type: HKPS8000
 Year of manufacture: 1975
 effective stroke: 200mm throat: 250mm (at center) table size: 320x320mm Installation height: approx. 345mm Voltage: 380V 
Perm. load: 80000N
 Drive type: HYDR Nedpfxog Ufvbj Afaocr Drive power: 1,5kW Oil quantity: 60l Oil viscosity: 3°E

Condition: used, Year of construction: 2003, pressure 250 t stroke 20 - 190 mm no. of strokes 25 - 140 /min Ncodjvuun Tspfx Afasr throat 460 mm passage to the back 590 mm dayligth 690 mm table surface area 1500 x 880 mm hole in the table 950 x 250 mm table height over floor 900 mm ram surface 870 x 725 mm ram adjustment 120 mm power requirement 30,0 kW Weight 32,0 t dimensions of the machine ca. 2,34 x 2,38 x 3,99 m x m x m permitted for manual loading and automatic mode according to the CE-norm with infinitely variable drive, light guard (make Sick), hydraulic clutch/brake combination, hydraulic overload protection in ram, automatic stroke adjustment, motoric ram adjustment, pneumatic counterbalance in ram, fix table, drawing cushion in table (20 t), motoric centralized lubrication, operator's console with two-hand operation Width between the tie rods in front 940 mm Side passage 900 mm

Condition: used, Year of construction: 1983, Technical details: Pressure: 160 t throat: 360 mm max. ram stroke: 500 mm distance table/ram: 800 mm Ncsdpou Nfvusfx Afaer clamping plate on table: 1250x630x100 mm passage opening in table: 4x Ø 62mm mm ram speed - forward: 200 mm/s ram speed - reverse: 125 mm/S ram surface area: 450 x 850 mm mortise hole in ram: Ø 49 mm height over floor: 810 mm total power requirement: 17 kW weight of the machine ca.: 7200 kg dimension machine xH: 2,1 x 1,4 x 3,4 m manual counter *

Condition: new, Year of construction: 2025, load capacity: 5,000 kg, Complete set including hand and double-foot remote control Nodjl Dq U Uepfx Afascr Digital speed display Hydraulic height adjustment Dimensions: Tilt height min: 800mm Tilt height max: 1900mm Horizontal height min: 1050mm Horizontal height max: 2000mm Clamping disc diameter 1500mm Length 2900mm, width 1400mm Weight 3200 kg Speed from 0.01 to approx. 0.9 rpm. CE certified