Paint shop

Ventherm Lackierkabine

Condition: new, Year of construction: 2025, Martin panel saw T 66 Cutting height: 155 mm Saw blade diameter: 450 mm Swivelling: one-sided Drive power: 5.5 KW Edging table length: 3.0 m Cutting width: 1350 mm Parallel stop via handwheel Standard cross table for length stop for angle cuts Length stop analogue with continuous system Table extension at the rear T66 T6615/2-a Drive power 5.5 KW T6630/3-a Edge table length 3.0 m T 6635/3-a Cutting width 1350 mm T 6641-a Parallel stop moved via handwheel T6660/1-a Standard cross table for angle cuts T 6670-a Length stop analogue T 6680/1-a Table extension at the rear Location: from stock 54634 Bitburg Gbodpfxev Erkaj Anmjr - available immediately - Some of the pictures show options that are not included in the offer.

Condition: used, Year of construction: 2001, Baffle width: 4000 mm. Baffle height: 1000 mm. External dimensions: 4600 x 1500 mm. 2 x 1.5 kW motors. Total nominal flow rate: 7000 m³/h. Right and left exhaust nozzles with 300 mm diameter. Gbjdpfx Aovvizkjnmjr Storage location: Garbsen

Condition: new, Year of construction: 2026, functionality: fully functional, total length: 5,000 mm, total width: 3,500 mm, total height: 2,950 mm, inner dimension height: 2,650 mm, inner dimension length: 4,900 mm, inner dimension width: 3,400 mm, Equipment: cabin, Automotive Spray Booth The automotive spray booth is a fundamental device in paint repair technology. It enables painting operations to be carried out in safe and comfortable conditions while minimizing the negative impact on the surrounding environment and the workspace. Specifications: - External dimensions: 5000 (+ air handling unit 1350 × 2900 mm) × 3500 × 2950 mm - Entrance door: 3000 × 2600 mm (three-wing design) - Service door: 700 × 2000 mm - Structure: made of steel sheets - Heat exchanger: standard steel - Panels: steel panels with mineral wool insulation in the walls Cabin Wall Structure: - Thickness: 50 mm - Insulation: EPS polystyrene - Color: white Cabin Base: - Cabin mounted directly on floor/concrete surface Double Ceiling: - External ceiling paneling - Full-surface plenum chamber for air supply Air Exchange System: - Supply system: - Jet turbine 4 kW – 2 units - Airflow capacity: 26,000 m³/h - Airflow system: - Jet turbine 5.5 kW – 1 unit - Airflow capacity: 18,000 m³/h Gjdpexnpczofx Anmsbr Lighting: - 8 side-mounted lamps - Ceiling lighting: 24 LED tubes Air Heating System: - Single-stage oil burner Riello model 40 G20 - Burner control: manual - Heating time: 8–15 minutes Filtration System: - Double-layer filtration structure - High-capacity air purification system with filtration efficiency up to 99%

Condition: excellent (used), Year of construction: 2008, Working width: 1100 mm Workpiece thickness: 3 – 160 mm Abrasive belt dimensions: 1,120 x 1,900 mm Variable feed speed: 2.6 - 13 m/min Feed motor output: 1.10 kW, 400 V, 50 Hz Extraction port diameter: 2 x 160 mm Compressed air supply: 6 bar Dimensions (L x W x H): 1705 x 1545 x 1905 mm 1st unit: Steel contact roller, diameter 160 mm Motor output: 15 kW, 400 V, 50 Hz 2nd unit: Combination unit with rubber-coated contact roller (Sh 65), rigid sanding shoe Motor output: 11 kW, 400 V, 50 Hz Abrasive belt cleaning via compressed air 3rd unit: Cleaning brush Multi-function display Multi-function lever (conveyor belt, workpiece thickness adjustment) Gbjdoychqzopfx Anmsr Electronic belt oscillation Pneumatic conveyor carpet oscillation Motorized workpiece thickness adjustment with LED display in 0.1 mm increments Units with emergency braking system Emergency stop button at infeed & outfeed Motor protection switch Roller table extension at infeed with 2 loose rollers Automatic star/delta start Complete documentation Note for used machines: • Specifications and prior sale subject to change. • Stated prices are ex works – loaded free of charge! • The machine has been cleaned and functionally tested. • All machines are sold as seen, without any warranty or guarantee. Buyers are welcome to inspect the machine on site. • Special agreements are only possible in written form. (We only respond to inquiries providing your address and telephone number!)

Condition: used, Year of construction: 2004, machine/vehicle number: 02919475, - Manufacturer Cefa - type. KLEENSPRAY - Year of construction 2004 - Operating side left - Working width 1.200 mm - Working height 900 mm + - 20 mm - Gun drive single version - Dry extraction - Extraction nozzle diameter 490 x 350 mm - Exhaust air capacity 6,500 m³/h - Paper belt transport system - Infinitely variable feed speed 1.5 - 7 m/min - PLC control with touch screen - Number of spray guns installed 0 pcs. - Height-adjustable spray guns - Number of paint pumps 0 pcs. - Suitable for solvent-based paints - Suitable for water-based paints - Length 4,450 mm - Width 3,360 mm + 1000 mm - Height 2,600 mm - Total connection ~ 7.1 kW / 28.6 A - Volt, Hz 400 / 50 - Location, in stock - Voltage fluctuations max. +/- 5 _____ Optionally, we can also provide you with a quotation for the assembly and start-up of the system, as well as training for your employees. Gjdpfxsv N D Ewj Anmebr We also offer regular maintenance and servicing of the machine on request. For further information, get in touch with us!

Condition: used, Year of construction: 2007, functionality: fully functional, total height: 5,980 mm, total width: 3,380 mm, total length: 3,074 mm, load capacity per storage section: 460 kg, input voltage: 400 V, Automated warehouse optimization storage system KARDEX Shuttle XP500 System Type: SHUTTLE-XP-500-3050x864 Control: C2000, with B/W OP2000 display Serial No.: Year of construction: 2007 Total Load: 2 x 33,500 kg Load per tray: 460 kg (evenly distributed) Tray dimension: 3050 x 864 mm Number of trays: 32 pieces (more on request) Dimensions Shuttle W x D x H: 3380 x 3074 x 5980 mm (height Kardex is adjustable to available height) Dimensions Shuttle D with full tray extraction table: 4198 mm Gbedpfxswnanks Anmor Power: 3/N/PE400 V, 17 A, 50/60 HZ, 8.6 kVA This offer is valid subject to the system being unsold. Technical details per Shuttle: - Maximum total capacity of the KARDEX Shuttle XP: 2 x 33,500 kg - Maximum tray capacity: 32 trays Medium X Type 2, 460 kg each, evenly distributed; more trays can be ordered. - Tray dimensions: 3050 x 864 mm - Machine dimensions: Width x Depth x Height: 3380 x 3074 (4198) x 5980 mm - Footprint of the system approx.: 14.19 m2 - Capacity with 32 trays: approx. 84 m2, each tray is approx. 2.64 m2 - Electronic volume measuring system in 25 mm grid - An access opening with sliding doors to protect people and stored goods - Control C2000 with graphic display OP-C2000 B/W - LED anti-glare lighting above access point - Use of toothed belt for minimum noise - Use of toothed belt for fastest order picking - Distances can be realized in steps of 25 mm by arranging the support profile, a prerequisite for high compression storage - Automatic full tray extraction table Price: On request, via email only Price: excl. VAT, including transport and installation Delivery time: in stock Machinehandel De Leeuw BV specializes in used machines and accessories for the metalworking industry and used paternoster systems from, among others, Kardex, Hanel / Haenel, Electrolux, Bertello, Megamat, Lista, Denocard, and automatic storage systems such as the Kardex Shuttle XP and XPlus systems. Machinehandel De Leeuw BV Oordeelsestraat 7 – b 5111 PA Baarle-Nassau The Netherlands

Condition: ready for operation (used), Year of construction: 2023, Load capacity: 1450/1125kg, load center: 600mm, lift height: 3200/4900mm, battery weight: 300-350kg, free lift: 900mm, mast height lowered: 2100mm, mast height extended: 4900mm, reach: 590mm, ground clearance under mast: 80mm, ground clearance at axle center: 50mm, track width: 1292mm, frame cross-section: 1058mm, front overhang: 655mm, wheelbase: 1120mm, rear overhang: 175mm, side shift: 80mm left / 80mm right, lost load thickness: 880mm, fork tilt back: 3°, fork tilt forward: 3°, min. turning radius: 1350mm, support arm height: 282mm, support arm length: 530mm, maximum speed: 6km/h, gradeability: 5%, battery capacity: 24V/270Ah, fork dimensions: 35x100x1070mm, front wheels (polyurethane): OD 200mm / width 50mm, rear wheel (solid rubber): outer diameter 250mm / width 75mm, AC drive motor: 24V / 2.5kW, AC pump motor: 24V / 5kW, rated power: 2.5kW, width: 1512mm, length: 1950mm, net weight without / with battery: 2800/3150kg, operating hours: 86h. An on-site inspection is possible. Gbsdpfx Answ S Tyajmjr

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: three-phase, warranty duration: 12 months, Equipment: cabin, Paint/spray booth dimensions without fan and control Panel! Extraction surface - dimensions (mm): 4430(w)x1900(h) Overall dimension(mm): 4530(w)x2350(h)x1910(d) Technical data: - Fan power 4.4kW (ATEX) - Fan suction capacity: 24000 m³/h (max 1200Pa) - Lighting: 2 pcs 2x58W (ATEX) - Connection voltage: 400V - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX Godpjia Taxsfx Anmobr - Complete technical documentation - CE Documentation - Warranty Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us

Condition: new, Year of construction: 2026, 540×250 Surface Grinder (MYS1022) is a compact machine designed for precision grinding of small and medium-sized metal components. Its robust construction and advanced technologies ensure high machining accuracy and reliable operation in demanding industrial environments. Main advantages of the 540×250 (MYS1022) surface grinder The 540×250 (MYS1022) magnetic surface grinder is an ideal solution for industrial facilities requiring precise machining in a compact format. Designed for professional users, it combines advanced technologies such as hydraulic feed in two axes and precision guideways with a solid construction, ensuring reliability and high machining efficiency. Its compact dimensions and high accuracy make it an excellent choice for smaller workshops and production facilities where space is limited. Key benefits include: High grinding precision – maximum grinding area of 540 × 240 mm and transverse feed accuracy of 0.02 mm ensure excellent surface finishing quality. Compact construction – dimensions of 1800 × 1400 × 1800 mm and a weight of 900 kg allow easy installation in smaller production facilities. Smooth hydraulic feed system – two-axis feed system enables precise movements with transverse speed up to 600 mm/min, ensuring efficient machining. Stability and durability – robust construction with double guideways minimizes vibrations, guaranteeing stable operation during intensive use. Easy maintenance – centralized guideway lubrication reduces manual maintenance requirements and increases machine availability. Ready for operation – the machine is fully equipped for immediate production, minimizing setup and downtime. Machine design and technology Robust construction and precision components The MYS1022 surface grinder features a heavy-duty construction weighing approximately 1000 kg, providing excellent stability during machining operations. Hardened and ground linear guideways eliminate vibrations, ensuring smooth table movement and high-quality surface finishes. The spindle, driven by a 1.5 kW motor, operates with a grinding wheel measuring 200 × 20 × 32 mm, enabling efficient processing of various metal materials. Technical specifications Parameter Value Table dimensions 500 × 250 mm Longitudinal / transverse travel 560 × 260 mm Gbedpfx Ajkkcm Ujnmsr Maximum grinding area 540 × 240 mm Maximum distance from table to spindle centerline 490 mm Table guideways Double guideway Transverse movement per vernier scale division 0.02 mm Transverse movement per handwheel revolution 2.5 mm Vertical movement per vernier scale division 0.01 mm Manual vertical movement per handwheel revolution 1.25 mm Grinding wheel dimensions 200 × 20 × 32 mm Grinding wheel speed 2850 rpm Main motor power 1.5 kW Hydraulic oil tank capacity 80 L Hydraulic pump motor power 1.5 kW Coolant pump motor power 40 W Machine dimensions 1800 × 1400 × 1800 mm Weight 1000 kg Standard equipment Magnetic table Grinding wheel Grinding wheel holder Cooling system Chip separator with magnetic filter Halogen lighting system Technical documentation (DTR) CE declaration

Condition: as good as new (ex-display), Year of construction: 2026, Compact wide-belt sanding machine with combination sanding unit Promotional features: - Switching the sanding pad on and off from the control panel - Switching the roller on and off from the control panel - Electronic control system Fox 500 KTR - Table extension with 2 rollers, with infeed and outfeed - Automatic table positioning with push button Article number: 5222100A2 Also suitable for smaller workshops for occasional use Combination sanding unit with sanding pad for fine sanding Standard equipment includes a diagonally grooved steel roller, Ø 120 mm, for calibrating Fine adjustment of the working height Clear control panel on the front Gbsdpfogf Sw Nox Anmer Robust, tubular-reinforced monoblock steel machine body, robot-welded, with work units mounted high up for maximum rigidity Motorized height adjustment of the work table with digital display Electronically controlled sanding belt oscillation Carpet feed via geared motor with two speeds Natural rubber feed carpet with a negative profile Flexible steel pressure bar in front of the first unit Rubber pressure rollers, in front of or behind each work unit Pneumatic belt tensioning per unit with decimal correction option for grit size/belt thickness Universally applicable for solid wood and veneer thanks to the combination unit Entry-level model for smaller companies Working width 950 mm Equipment details: Combination unit for calibrating and sanding Diagonally grooved steel roller, Ø 120 mm, with fine height adjustment Hard sanding pad with graphite pad Universal design for calibrating and sanding solid wood, chipboard and veneer Technical data Length (product) approx. 1388 mm Height (product) approx. 1668 mm Width/Depth (product) approx. 1545 mm Connection for dust extraction Dust extraction nozzle diameter 140 mm Electrical data Connection voltage 400V Current type AC Phase(s) 3Ph Mains frequency 50Hz Power feed motor 0.33 / 0.55 kW Power height adjustment motor 0.25 kW Power drive motor 7.5 kW Sanding unit Sanding belt length 1525 mm Sanding width max. 950 mm Sanding belt width 970 mm Feed unit Feed speed 4.5 / 9 m/min Workpiece Workpiece height min. 4 mm Workpiece height max. 170 mm