Injection molding machine

Stork IMM SX S 4400EP-5650-065

Year of construction: 1974, condition: refurbished (used), functionality: fully functional, machine/vehicle number: 1293, CNC Radial Forging Machine GFM mod. SX-16 Manufacture: GFM (Austria) YOM: 1974 / 2022 Model: SXL-16 Machine number: 1293 PLC: Siemens S7 - Technology V4.2 with CNC Bosch Rexroth XM Numbers of Hammers: 4 Forging force: 800 Ton (200 t per Hammer) Strokes per minute: 580 Hammer length: 320 mm Maximum hammer setting scope Isdpfx Ajq U Sa Sjgwetp - calculated by diameter: 100 mm Maximum diameter of forging regarding: - structural steel: circular cross section – Ø 160 mm square cross section – 130 mm - high alloy steel: circular cross section – Ø 120 mm square cross section – 100 mm Extreme quadrangle: 12 x 120 mm Maximum length of forging: 6000 mm Min and Max diameter of mounting in manipulator: 30 - 160 mm Feed of manipulator A: 6800 mm Feed of manipulator B: 7200 mm Passage through manipulator: Ø 130 mm Manipulators speed in fast move: 400 mm/s Feed speed of manipulators (stepless adjustment): 10 ÷ 115 mm/s Cooling water pressure: 3 ÷ 5 bar Temperature of inlet water: max. 30˚C Cooling water consumption: 34m3/h Pipe diameter for cooling water: 2” Compressed air pressure: min. 5 bar Pipe diameter for compressed air: Ø20 mm Consumption of compressed air: 1,5 Nm3/h Power supply (nominal power): 350 kW Motor voltage: 500 V Control voltage 220 V Power of main engine: 200 kW Power of pump motors: 185 kW Power of manipulators motors: 2 x 22 kW Dimensions of the machine Axis height of forging above the hall level: 750 mm Maximum height of machine above the hall level: 2.050 mm Maximum length of machine on the hall level: 33.740 mm Foundation length: 34.200 mm Maximum width of machine on hall level without loading equipment: 4350mm Foundation width: 15.600mm Machine net weight: 124.490 kg

Condition: used, Year of construction: 2004, Technical details: screw size: 105 mm injection shot weight in Polysterol: 4727 g/PS closing pressure: 2300 kN plate size: 2830 x 2400 mm opening stroke: 3700 mm daylight: 1100-1800 mm injection volume: 5195 ccm injection pressure max.: 2296 bar dimensions: 14,2 x 4,15 x 2,84 mm Itedpfjtrbcbsx Agwjp total wight: 143 t tie bars distance: 2000 x 1600 mm Robot system core pulls hot runner controller -     The machine is in a very good condition       -     Additionally complete cutters available. -     A conveyor belt and Robot Systems(Model 2012) *

Condition: excellent (used), Year of construction: 2003, operating hours: 67,092 h, BATTENFELD HM 10000-9200 Manufacturer: BATTENFELD Type: HM 10000-9200 Control system: UNILOG B4 Year of construction: 2003 Operating hours: 67092 h Technical data closing side Itodpsrdyq Rsfx Agwep Clamping force: 10000 kN Tie bar dimensions h x v: 1120 x 1400 mm Panel size h x v: 1960 x 1690 mm Installation height min.: 550 mm Installation height max.: 1020 mm Panel distance max.: 2120 mm Opening stroke: 1100 mm Ejector stroke: 300 mm Ejector force: 118 kN Centering movable plate D: 250 mm Centering of fixed plate D: 315 mm Technical data injection side Screw diameter: 120 mm Stroke volume: 5655 ccm Injection pressure: 1632 bar Screw length: 22 l/d Screw stroke: 500 mm Screw speed: 130 min Screw torque: 11370 N Plasticizing flow: 144 g/s PS Injection flow into the atmosphere: 1144 g/s PS Number of heating zones: 8 Nozzle path: 700 mm Dimensions & weight Machine dimensions LxWxH: 11.6m x 2.9m x 2.5m Total weight: 76500KG Equipment On-screen text German Compact flash drive Hydraulic core pull 4x Leveling elements EUROMAP 12 interface Interface for temperature control unit Enlarged oil cooler mold heating 16x

Condition: excellent (used), Year of construction: 2006, Krauss Maffei KM 800 – 12000 MX injection molding machine Year of production - 2006 Closing system: - Mold closing force: kN 8000 - Mold opening force: kN 560 - Dimensions of the mounting plate (h x v): mm 1600 x 1530 - Clearance between columns (h x v): mm 1120 x 1000 Isdpfetmq Akox Agwstp - Mold opening path: mm 1600 - Mold installation height (min - max): mm 500-1100 - Plate opening stroke: mm 2100 - Ejector stroke: mm 300 - Ejector force: kN 200/100 Injection system: - Screw diameter: mm 135 - Injection pressure: bar 1389 - Injection volume: cm3 8588 - Injection weight for PS: g 6098 - Number of screw revolutions, standard/option: rpm 121/153 - Injection efficiency (standard) Electric-hydraulic equipment - Nominal power of the pump motor: kW 110 - Installed power of heaters: kW 57 - Number of cylinder heating zones: - 7 - Number of dry cycles according to Euromap: 1/h 965 - Oil tank capacity: l 1500 Dimensions and weight - Net weight with control cabinet: t 45 - Machine dimensions (length x width x height): m 10.81 x 2.92 x 2.51

Year of construction: 2002, condition: good (used), Make: Matsuura Type: LX-O Control: YASNAC Year: 2002 Specifications Itsdpfxolz Rvls Agwep Metric US Standard X - Travel 330 mm Y - Travel 300 mm Z - Travel 250 mm Table Length 540 mm Table Width 320 mm Table load 100 Feed rate X-Axis 90000 mm/min. Feed rate Y-Axis 90000 mm/min. Feed rate Z-Axis 90000 mm/min. Spindle Taper 30 ISO/Bt/Mk Power on spindle 7.5 kW Speeds / ranges 40000 Rpm ATC / revolver 30 Chip conveyor Yes Dimensions (Estimate) Length 2800 mm Width 2600 mm Height 28000 mm Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: ready for operation (used), Year of construction: 1980, Power: 300 to Size of bolster: 1.200 x 850 mm Itodpjd A Hbcjfx Agwep Overhang: 400 mm Width of ram: 1.100 mm Opening in bolster: 400 x 250 mm Daylight: 500 mm Frequency: 32 1/min Stroke: 30 - 140 mm Ram adjustment: 105 mm Weight: app. 19.500kg Other - allowed for 2-Hand safe working - euqipped by safety valve Herion Xsz 20 - Motorized grease lubrication - Pneumatic ram balancing cylinders - Motorized ram adjustment - T-slots in ram - Stand alone control panel - bearing of con rod overhault

Condition: refurbished (used), Year of construction: 1974, functionality: fully functional, machine/vehicle number: 1276, CNC Hot Radial Forging GFM SX-13 New in 1974 / 2022 New control system PLC SIEMENS S7 Machine number: 1276 No. of Hammers: 4 Forging force each hummer: 160 Ton Hammer stroke / min: 700/min Hammer lenght: 240 mm Diameter setting range: 80 mm Maximum forging diameter: Structural steel, round-cross section: Ø 130 mm square cross section: Ø 115 mm Smallest dimensions forged: Ø 25 mm Manipulator A max. displacement: 6820 mm Manipulator B max. displacement: 7150 mm Maximum workpiece length: 6000 mm Rapid speed manipulator: 400mm/sec Itedpfx Aeq U R T Negwep Total connected power: 300 kW 380 V, 50 Hz Machine dimensions: Forging height over floor: 615 mm Total height pf the machinr over floor: 1665 mm Total machine lenght: 32670 mm Total foundation lenght: 33400 mm Tot. machine width (without auxliary equipments): approx 3885 mm Total foundation width: 16000 mm Total weight of the machine: 84.000 Kg

Condition: good (used), Year of construction: 2003, travel distance X-axis: 13,000 mm, travel distance Y-axis: 4,500 mm, travel distance Z-axis: 1,000 mm, spindle speed (max.): 30,000 rpm, distance between stands: 6,500 mm, spindle nose: HSK A63, X-axis: 13.000 mm Y-axis: 4.500 mm Z-axis: 1.000 mm Distance between columns: 6.500 mm C-axis: 190º A-axis: 110º Positioning speed XYZ: 15.000 mm/min. Positioning speed AC: 10 tpm CNC Controller: Siemens 840D Spindle nose: HSK A63 Spindle speed: 30.000 rpm Itedpfett I Sfox Agwep Spindle power: 20 kW Toolchanger: 20 Pockets Torrestool tables: 16x X-axis: 11.500 mm Y-axis: 3.500 mm Z-axis: 750 mm Country of origin: Spain Machine size LxWxH: 19.000 x 11.000 x 6770 mm Machine weight: 70.000 kg The Torresmill Gantry is a 5-axis CNC milling and drilling machine, specially designed to work on aeronautical materials (Composite, Aluminum, Titanium, Steel, ...). The Torresmill gantry is perfectly combined with the Torrestool universal clamping device, guaranteeing flexibility and process time.

Condition: good (used), Year of construction: 1999, Engel ES 7 K Clamping force 1000 tons Year built: 1999 Screw diameter: 105 mm Injection volume: 4160 cm3 Number of heating zones incl. nozzle: 7 Pump drive power: 130 kW Clamping force: 1100 tons Opening stroke: 1100 Min-max mould height Tie bar spacing: 1400x1150 Machine weight: 64 tons + 18 tons Plus Engel Robot Type: ERC 83/2 - CL Year built: 1999 Itjdpfx Aolyr Awegwep Separate control cabinet

Condition: good (used), Year of construction: 2016, Engel duo 23050/3200 (2017) Tie bar distance: 2240x 1800mm Min - Max mould: 1100-2000mm Screw dia : 160 mm Iodpfx Asv Eviaegwjtp Shot volume: 14480 cm3 CC300 controll