Lead/traction spindle lathe

SASTA STANKO SA562 M

Year of construction: 1993, condition: used, TYPE: DEA 400/2000 Year: n.d. MAXIMUM RAM CAPACITY: 400 tons SLIDE STROKE: 1,100 mm MAXIMUM SHUT HEIGHT: 1,600 mm TABLE DIMENSIONS: 2,000 x 1,600 mm Fjdpsihf R Uofx Ad Ijpi FAST STROKE: 650 mm/sec CUSHION CAPACITY: 160 tons CUSHION STROKE: 400 mm HEIGHT ABOVE GROUND: 5,800 mm DISTANCE BETWEEN UPRIGHTS: 3,400 mm LATERAL WINDOW: 1,600 mm

Condition: used, Year of construction: 1984, turning diameter over cross slide: 1,600 mm, turning diameter: 2,000 mm, turning diameter over bed slide: 2,000 mm, turning length: 35,000 mm, workpiece weight (max.): 63,000 kg, Center Lathe SKODA - SUT 200 TD MACH-ID 9446 Manufacturer: SKODA Model: SUT 200 TD Year of manufacture: 1984 Tandem construction on one bed, with left and right headstocks Faceplate double tailstock left and right Double carriage Steady rest included Roller rest included Operator panel with scales requires attention and replacement Motorized tailstock for each side (left and right) 3-bed way design Torque on chuck: 160,000 Nm Minimum turning diameter: Ø 315 mm Industries served: - Shipyards - Propeller shaft manufacturing - Hydraulic cylinder shafts - Camshafts - Defence & Aerospace - Rolls and shafts for steel mills - Crankshafts Specifications Metric / Imperial Fjdpfx Adeynky Ao Iopi Turning length: 35,000 mm Swing over bed: Ø 2,000 mm Swing over carriage: Ø 1,600 mm Spindle power: 75 kW Bed width: 1,600 mm Quill diameter: Ø 400 mm Quill stroke: 250 mm Max spindle speed: 180 rpm Feed X-axis: 5,000 mm/min Feed Z-axis: 5,000 mm/min Workpiece weight: 63,000 kg Approximate dimensions: Length: 42,000 mm Width: 3,250 mm Height: 3,250 mm Weight: 158,000 kg Please note: The information on this page has been provided to the best of our knowledge and, where possible, obtained from the manufacturer. The information is given in good faith, but accuracy cannot be guaranteed. Accordingly, they do not constitute representations or contractual terms. We recommend verifying all important details.

Condition: used, greates pass round over bed 540 mm swing diameter over face slide 370 mm centre distance 3000 mm centre height 270 mm Fpodpfexnqzxsx Ad Ioi turning dia. in gap 815 mm bed width 344 mm spindle bore 88 mm spindle diameter in front bearing 133 mm spindle taper 11" D1 Camlock turning speed range 18-1400 U/min turning speeds 16 3-jaw chuck Röhm Ø 315 longitudinal feeds: 0,06-1,0 mm face feeds 0,03-0,5 mm metric threading 0,4-14 mm inch threading 2-72 G/1" thread - module 0,3-3,5 mm thread - DP 8-60 Pitch tailstock quill diameter 75 mm quill stroke 230 mm taper of tail spindle MK 5 slide valve travel 280 mm upper head travel 150 mm Overall size ca. 4700 x 1100 x 1400 mm weight ca. 3200 kg power capacity 9,4 kW Accessories: 2-axis digital display Fagor Röhm wedge bar chuck Ø 315 mm incl. hard base jaws and hard attachment jaws Multifix steel holder size C incl. 6 interchangeable cassettes Rotating center point Switchable lathe chuck guard 2 steady rests Chip guard Coolant device Work light Guideways in good condition without scratches, not worn Machine is in good overall condition with signs of wear commensurate with age. Includes operating instructions Translated with (free version)

Condition: good (used), Year of construction: 1992, Indoor crane, crane, electric wire rope hoist, hoist, motor winch, motor winch, tackle, traction winch, block and tackle -Manufacturer: steel, crane chassis with electric cable pull -Crane chassis: Type GO 24 20 16 -Traveling speed: 20 m/min -Roller pitch: 800mm -Cable: Type AS 2010 -Traction: 1000 kg / load capacity 4000 kg -Drum speed: 16 m/min / stroke 4 m/min -Lifting height: mm -Transport dimension: 1250/1180/H400 mm Fedpel Tuvdefx Ad Ijpi -Own weight: 356 kg

Condition: used, Year of construction: 1970, machine/vehicle number: 120895, pressure:63 t throat:250 mm stroke:8 - 100 mm no. of strokes:120 Hub/min table::715 x 500 mm dayligth:330 mm ram adjustment:63 mm clamping plate:700 x 480 mm hole in the table:240 mm Hole in clamping plate:110 mm dimension of ram:450 x 280 mm weight of the machine ca.:5,5 t dimensions of the machine ca.:1,2 x 1,7 x 2,7 m Fodpfx Adofx Hv Hs Ispi hydraulic tilting single column eccentric press, tilting in 4 steps, opening to rear (325 x 500mm) and below (360x160mm) with central lubrication via hand pump, additional clamping plate 700 x 480 x 850 mm, two-hand operation, foot-trip operation possible, operating-mode selector for adjustment of continuous or single stroke, emergency cut-off, piece counter, various accessories

Condition: new, - Capacity: 700 x 2 mm - Conical rollers - Removable top roller - Foot control - Emergency stop - Documentation - 400V Fpodpfx Asihv Hpod Ioi

Condition: good (used), 1 used surface grinding machine Manufacturer: Jung Model: HF 50 Technical specifications: - Z-axis travel: 400mm - X-axis travel: 500mm - Y-axis travel: 200mm - Table length: 720mm - Maximum spindle speed: 4000rpm - Table width: 200mm - Minimum spindle speed: 1000rpm - Transport dimensions: 2300mm x 1500mm x 1700mm (L x W x H) - Transport weight: 2000kg Fpjdjxgbb Tjpfx Ad Iei Equipped with: - Digital readout - Diaform device

Condition: new, Year of construction: 2026, functionality: fully functional, Swing dia over bed 500 mm Swing dia over cross slide 270 mm Swing dia in bridge 700 mm Length of bridge 357 mm Center high 250 mm Center distance 1500 mm Fpedpjyt Iaqsfx Ad Iei Width of bed 340 mm Max weigth of wpc. 300 kgs Spindle speed 22 – 2000 rpm Spindle hole D53 mm Spindle power 5,5 kW Weight ca.1950 kgs Dimensions LxWxH = 3200 x 1100 x 1500 mm Accessories and features - 3 axis D.R.O. - Chuck protection - 3 jaws chuck D250 mm - 4 jaws chuck D300 mm - Tool holder protection - Stopper for long. slide - Steady rest - Travelling rest - Center - Reduction adapter for main spindle - Tailstock - Coolant unit - 4-fold toolholder - Machine lamp - Rapid speed on long, and cross slides - CE marking - Manuals

Condition: excellent (used), Year of construction: 1978, functionality: fully functional, machine just arrived and will be cleaned soon. turning diameter over bed: 400mm distance between centers: 1000mm spindle size: 50 mm Fpodpfxsyh Ndwj Ad Isi chuck size 200mm speed range 40 rpm to 2000 rpm machine weight: 1700kg including 3 jaw chuck and tool holder

Condition: ready for operation (used), Year of construction: 1969, Centre height: 355 mm Centre distance: 3000 mm Max. swing diameter over bed/gap/cross slide: 715/790/520 mm Spindle bore: 86 mm Spindle mount according to DIN 55027: Size 11 Quill taper of tailstock: MK 5 21 spindle speeds: 5.6 - 560 rpm 42 feeds longitudinal/cross: 0.09 - 5.6/0.045 - 2.8 mm 22 Whitworth threads: 2 - 28 TPI 28 metric thread pitches: 1 - 14 mm Fpodpfx Aexpuu Eod Isi 27 module thread pitches: 0.25 - 3.5 module 32 module threads: 4 - 56 module 32 diametral pitch threads: 8 - 112 DP Drive motor, pole-changeable: 380 V, 7/11 kW Weight approx.: 7 t Space requirement approx.: 6000 x 2300 mm