Slitting machine

SAS Ferro-Rez

Year of construction: 2025, condition: new, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Itedpeflk Awefx Ah Njb Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: ready for operation (used), technical Details: Speed - 130m/min. , Year - 2006, run out table - 6 m Wire diameter range 4-12 mm Itodpfx Ajtndgpjh Njb

Condition: new, Year of construction: 2025, -TFON Leveltech® Leveling Machine Series -Model: L-9060. -Material Thickness: 1.0 mm – 30.0 mm. -Maximum Material Width: 600 mm -Minimum Material Length: 145 mm. -Flattening Gap Adjustment: Servo Hydraulic / PLC Controlled Overload Protection: Standard Machine Weight: 26.000 kg. Machine Dimensions (L × W × H): 4,400 × 7,185 × 2,260 mm Model: L-9011 Material Thickness: 1.0 mm – 30.0 mm. Maximum Material Width: 1,100 mm. Minimum Material Length: 145 mm Isdpfjhwb U Tox Ah Netb Flattening Gap Adjustment: Servo Hydraulic / PLC Controlled Overload Protection: Standard Machine Weight: 31.000 kg Machine Dimensions (L × W × H): 4,600 × 7,185 × 2,260 mm Model: L-9013 Material Thickness: 1.0 mm –30.0 mm Maximum Material Width: 1,300 mm Minimum Material Length: 145 mm Flattening Gap Adjustment: Servo Hydraulic / PLC Controlled Overload Protection: Standard Machine Weight: 35,000 kg Machine Dimensions (L × W × H): 5,000 × 7,185 × 2,260 mm Model: L-9016 Material Thickness: 1.0 mm –30.0 mm Maximum Material Width: 1,500 mm Minimum Material Length: 145 mm Flattening Gap Adjustment: Servo Hydraulic / PLC Controlled. Overload Protection: Standard Machine Weight: 40.000 kg Machine Dimensions (L × W × H): 5,200 × 7,185 × 2,260 mm Model: L-9020 Material Thickness: 1.0 mm –30.0 mm Maximum Material Width: 2,000 mm Minimum Material Length: 145 mm Flattening Gap Adjustment: Servo Hydraulic / PLC Controlled. Overload Protection: Standard Machine Dimensions (L × W × H): 5,700 × 7,185 × 2,260 mm.

Condition: used, Hydraulic Guillotine Shear STEINER Type HTS 30/20 R Machine No. 315 Year of manufacture: 1982 Cutting length: 3050 mm Cutting thickness: 20 mm Backgauge: 800 mm, motorized control Motor power: approx. 30 kW Power supply: 400 Volt, 50 Hz - Backgauge with ELGO position control - Backgauge adjustment via ball screw spindles - SICK safety light curtain at the front for access protection - 3 material support arms with ball rollers - Electric foot switch - Spare blade - Oil cooler with air heat exchanger - Extremely heavy-duty machine in very robust construction Base machine dimensions L x W x H: 4650 x 2610 x 3200 mm Base machine weight: 27,000 kg Transport space required (base machine) L x W x H: 4650 x 2610 x 3200 mm Itodpfed Hxx Ajx Ah Nob Transport space required (additional) L x W x H: 3500 x 2450 x 1400 mm Total weight: 27,000 kg Good condition Machine can be inspected at our warehouse in 37235 Hessisch Lichtenau. Test cuts possible.

Condition: new, Year of construction: 2025, Single band console decoiler 500 mm - Loading capacity 1.500 kg - Inner φ 480-530 mm Itodpfxsfvbxqo Ah Nsb - with 4 clamping arms, ball bearings and with disc brakes - max coil width: 500 mm

Condition: used, Year of construction: 2021, operating hours: 831 h, Equipment: ABS, Doosan DX 55-9C * Dead weight 5.5 t. Isdpjullmdofx Ah Netb * Transport length 5.85 m. * Transport width 1.88 m. * Transport height 2.56 m. * Bucket capacity min. 0.18 m³ * Track width 400 mm. * Driver protection Kb. * Reach 6.15 m. * 2 x proportional control * Powertilt with Lehnhoff system * Air conditioning * ZLG 5500 KG * Engine 41 KW 56 HP * Blade support

Condition: new, 3000 mm Working width 360 mm Wheel width 360 mm roll diameter 60 mm 900 kg Iodpfxjfv Atte Ah Nstb height adjustment 650 - 1100 mm weight of the machine ca. 0,050 t dimensions 3,1 x 0,45 x 0,6 m

Condition: new, Year of construction: 2024, A vineyard post roll forming machine is used for vineyards and orchards to produce the stakes and posts. Normally, grape posts are 1.5-2mm thickness. The production line consists of Decoiler, Servo Feeder Straightener, Press, Stamping Tool, Roll Form Machine and Shear. Isdpet Tcz Usfx Ah Notb

Year of construction: 2023, operating hours: 0 h, condition: new, MG20B is suitable for bending your steel into the desired shape. Product information: - Voltage: 380 V (optional with 220 V available) - Motor Power: 1,5 kW - Dimensions Machine: 60cm x 45cm x 32cm - Dimensions Machine frame: 57cm x 44cm x 60cm - Ideal for your construction company or also for your construction sites - Easy to carry - In addition to the individual bending process, a bending sequence can also be programmed - Stirrup head for different reinforcing steel Ø are included in the accessories (incl. accessories, see pictures) - Possible in automatic or manual mode - Bending capacities depending on steel strength according to table (see pictures) - Optional available with digital control panel - Net weight: 95 kg Itodpfx Ahsm Sgx De Nob Shipping: Europe-wide (self-collection also possible) If you have any questions, please do not hesitate to contact us!

Condition: used, Year of construction: 2001, sheet width 3200 mm plate thickness 3.0 mm ST thickness at "Niro-steel" 2.0 mm Opening width / upper beam 300 mm speed OW 40.0 mm/sec Bending beam adjustment 80.0 mm work height max. 900 mm speed BW 90.0 Grad/sec control MULTIBEND 5000 back stop - adjustable 10 - 1550 mm accuracy +/- 0.1 mm air pressure 5.0 bar Iodoxabz Tjpfx Ah Nstb Number of working hours ca. 1.000 h total power requirement 2x 4.0 kW voltage 400 V weight 4400 kg range L-W-H 4295 x 2225 x 1775 mm New price approx. 85.000 euros Machine with only approx. 1.000 operating hours (!!) good condition (!!) Special price on request - in checked condition - machine video - ?v=VP6emx4HTYM ! Maximum flexibility when bending cassettes, boxes and profiles ! High flexibility in bending part design ! High productivity and throughput ! Easy to use Equipment: - motorized universal swivel bending machine "RAS 73.30" * high-precision mechanics with modern control technology * for individual and series production * robust high-speed machine with high axis speeds * torsion-free welded construction - RAS CNC control model "MULTIBEND 5000" * material and tool library * swiveling - front right * 1x emergency stop button - CNC electro-motorized upper beam adjustment * fast closing and opening speed * programmable opening and closing height * bending radii without special tools (multiple bends) * rigid upper beam for straight bending parts * 1x set of RAS split upper tools .. height 80 mm * RAS "click-in" tool system - CNC electro-motorized bending beam adjustment * fast swivel movement: short production time * crowning system compensates for deformation by the bending forces * 1x set of RAS split bending tools - CNC electro-motoric back stop * fast positioning, repeatable work * table plates hold the weight of the sheet * stainless steel table plates with ball rollers - 2x freely movable double foot switch - 1x RAS tool trolley for bending tools (movable) - operating instructions (PDF) + original circuit diagram