Cross cut saw UTK - 600

Reinhold Beck Maschinenbau GmbH UTK 600

Condition: new, Year of construction: 2024, Chopper knife 40 x 40 concave Knife for Weima, large size ... Csdpfx Amobxu Dheaorf Suitable for almost all common shredders/granulators Available from stock in Bitburg Subject to prior sale

Condition: used, Year of construction: 2024, DOWEL HOLE DRILLING MACHINE GANNOMAT "DB 21400V, 3Ph, 50Hz / 1.5 kW, complete in standard design with: - Fully automatic electronic control with pulse operation via foot valve for clamping-drilling-releasing, electric intermittent operation. - Automatic retraction of the drilling unit after reaching the set drilling depth. - Automatic extension of the drilling hole depth when drilling on the end face. This eliminates the need to adjust the drilling hole depth from flat-face to end-face drilling (+10 mm, e.g. for a dowel length of 35 mm, drilling depth on the flat face 14 mm and drilling depth on the end face 24 mm). - 1 drilling bar with 21 spindles, pitch 32 mm, motor 1.5 kW (drilling feed 0-70 mm), incl. 21 quick-change chucks (Ganner system) for easy changing of the drill bits. - Easy pivoting of the drilling unit from 0° to 90°, supported by gas cylinders. - 1 clamping support movable in the Y-axis with 3 pneumatic clamping cylinders, for workpiece height up to max. 80 mm. Ideal stop system consisting of: - 1 stop rail 1800 mm for drilling shelves (aluminum profile 40x40 mm) with 3 stop blocks, with quick-change system, easily interchangeable from right to left stop side for drilling shelves in carcass structures in mirrored fashion, also suitable for row drilling in the 32 system. - Side stops and position settings, as well as the position of the drilling height above the support table, are adjusted by means of mechanical digital counters. - Side stops can be easily pivoted away, for the shortest possible conversion from carcass to frame and row drilling. - Clamping arms for the clamping support designed for row drilling positions up to max. 300 mm. - Ideal three-stage tool system. - 1 set of drill bits for dowels: - 5 carbide dowel drill bits, Ø 8x77 mm, right-hand - 4 carbide dowel drill bits, Ø 8x77 mm, left-hand Basic machine DOWEL HOLE DRILLING MACHINE GANNOMAT "DB 21400V, 3Ph, 50Hz / 1.5 kW, complete in standard design with: - Fully automatic electronic control with pulse operation via foot valve for clamping-drilling-releasing, electric intermittent operation. - Automatic retraction of the drilling unit after reaching the set drilling depth. - Automatic extension of the drilling hole depth when drilling on the end face. This eliminates the need to adjust the drilling hole depth from flat-face to end-face drilling (+10 mm, e.g. for a dowel length of 35 mm, drilling depth on the flat face 14 mm and drilling depth on the end face 24 mm). - 1 drilling bar with 21 spindles, pitch 32 mm, motor 1.5 kW (drilling feed 0-70 mm), incl. 21 quick-change chucks (Ganner system) for easy changing of the drill bits. - Easy pivoting of the drilling unit from 0° to 90°, supported by gas cylinders. - 1 clamping support movable in the Y-axis with 3 pneumatic clamping cylinders, for workpiece height up to max. 80 mm. - Ideal stop system consisting of: - 1 stop rail 1800 mm for drilling shelves (aluminum profile 40x40 mm) with 3 stop blocks, with quick-change system, easily interchangeable from right to left stop side for drilling shelves in carcass structures in mirrored fashion, also suitable for row drilling in the 32 system. - Side stops and position settings, as well as the position of the drilling height above the support table, are adjusted by means of mechanical digital counters. - Side stops can be easily pivoted away, for the shortest possible conversion from carcass to frame and row drilling. - Clamping arms for the clamping support des Csdpfx Aexnlflsmaorf

Condition: new, Year of construction: 2024, carrying capacity per cantilever arm: 500 kg, shelf height: 3,200 mm, total length: 2,100 mm, total height: 3,200 mm, axle spacing: 1,000 mm, load capacity per stand: 2,500 kg, Cantilever rack in hot-dip galvanized design: Scope of delivery: 3 rack stands, height 3.2 m with base section, 1.8 m usable depth (2 m total depth) 12 cantilevers with 1.8 m usable depth (for chipboard with approx. 2.1 m depth) Longitudinal and diagonal struts for 4 m rack length (distance 1.3 m) Fastening material (screws, nuts and washers) Net price: €2,490.00 plus VAT Detailed description: - Stable steel construction made of IPE profiles (screw system) - Rack height 3,200 mm - Load capacity per stand 2,500 kg - Base section and cantilevers with 1,800 mm usable depth - (for 2,100 mm chipboard depth) - Cantilevers height adjustable in 100 mm increments - 4 screwable screws per stand Cantilever arms, standard (= 5 storage levels) - Load capacity per cantilever arm 500 kg - Including longitudinal and diagonal braces for 1,000 mm spacing - Shelf length = 2,100 mm Crjdpjqt Dmyofx Amaof - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Made in Germany - Short delivery time Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. Delivery for stock items can take place in approx. 1 week after receipt of the order. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Year of construction: 1980, condition: good (used), Stellite forming machine VOLLMER GF10U Sheet thickness: 1 to 4 mm Codpfegxb Ebox Amaerf Width of band saw blades: 60 to 420 mm Circular saw blades: 300 to 1,200 mm diameter Electric feed drive via geared motor

Condition: as good as new (ex-display), Year of construction: 2026, S&F drum chipper type ATH 220x530/3 Demonstration machine / trade fair machine / new machine Solid design with long service life Feed height: 200 mm Feed width: 500 mm Number of chipper knives: 2 pieces Number of counter knives: 1 piece Rotor diameter: 520 mm (solid steel rotor) Number of feed rollers: 3 pieces Throughput rate: up to approx. 20 rm/h * Chipping length: approx. 30 mm Chipper drive power: 45 kW or on request Feed roller drive power: 2 x 2.2 kW Operating/control voltage:400/220 V, 50 Hz Weight: 2,600 kg *depending on chipper length, kW main motor, number of knives, feed S&F chippers and drum chippers with horizontal infeed are used in many areas of the wood processing industry (sawmills, timber mills). Chippers from the ‘ATH’ series produce high-quality and homogeneous wood chips with a low proportion of fines from residual wood, for example as quality chips for the cellulose industry or as fuel chips for energy generation Advantages: - Maximum throughput Codpfx Aew I R Rnemaorf - Low fines content - Low maintenance - Flexible use - Customised production

Condition: reconditioned (used), Robotic welding system with a 2 m, dual-station positioner. For sale is a robotic welding system from Yaskawa Motoman, including an RM2-250 positioner. Safety technology Robot: UP20 XRC Nozzle cleaner Codpfsd Tfb Njx Amaerf and more We can assemble and commission the system for you. We also offer training and instruction. The system will be refurbished according to the customer's requirements. We are a YASKAWA system partner and offer you complete service for your Motoman robot and your systems.

Condition: like new (used), Manufacturer: V. Randwijks Rotor Dia.: 500mm Rotor Width: 700mm Crsdsg Snt Sopfx Amasf Electrical Motor: 22kW / 1.470 RPM

Condition: new, VKM supplies spare parts for Oswald and some Bezner-Oswald machine, BÖGLI bandsaws and replacement knives for various woodworking machines. Partly the parts can be delivered from stock. For the knives, send us your desired dimension and we can offer and supply them to you at a reasonable price. Cedpfx Amsg Rn Avoasrf Send us your inquiry today!

Condition: used, Year of construction: 1997, Line 3 Stenner MHS9 machines from 1997 Crodpfx Amsw Nrhksasf

Condition: new, Year of construction: 2024, functionality: fully functional, saw blade diameter: 500 mm, cutting height (max.): 145 mm, cutting width (max.): 510 mm, overall weight: 400 kg, extraction nozzle diameter: 150 mm, rotational speed (min.): 2,800 rpm, power: 5.5 kW (7.48 HP), STROMAB PS 50/F pendulum cross-cut saw, brand NEW Specification: • condition - new • engine power - 5.5 kW • blade diameter - 500 mm • engine shaft diameter - 30 mm • engine speed - 2,800 rpm • max cutting width - 510 mm • max cutting height - 145 mm • additional extension tables - 2 x 2 m • weight 400 kg Credpfsrdwm Tjx Amaef • 2024/2025 year of manufacture • noise emission - 85.5 dB (A) • the machine meets CE standards Additional information: • tables visible in the photos included with the machine (2 x 2.0 m) • available within 7-10 working days • the price does not include VAT and transport costs