Sheet Metal & Profile Shot Blasting Mach

PROTON BPBLINE

Year of construction: 2002, condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. - Vertical clamping block with self-adjusting push plate. - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm - 60º: 910x302mm - 45º: 716x304mm - 40º: 716x304mm - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm IPE beam - 45º: 600x220mm DRILLING UNIT Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Work capabilities: - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm Hfedpfxehzbipe Agfjf - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.

Condition: used, Hydraulic Guillotine Shear STEINER Type HTS 30/20 R Machine No. 315 Year of manufacture: 1982 Hfjdpfsd Hxx Asx Agfsf Cutting length: 3050 mm Cutting thickness: 20 mm Backgauge: 800 mm, motorized Motor power: approx. 30 kW Power supply: 400 Volts, 50 Hz - Backgauge with ELGO positioning control - Backgauge adjustment via ball screws - SICK safety light curtain at the front as reach-in protection - 3 material support arms with ball transfers - Electric foot switch - Spare blade - Oil cooler with air heat exchanger - Very robust machine with extremely solid construction Machine footprint (L x W x H): 4650 x 2610 x 3200 mm Machine weight: 27,000 kg Transport dimensions (base machine) (L x W x H): 4650 x 2610 x 3200 mm Transport dimensions (additional) (L x W x H): 3500 x 2450 x 1400 mm Total weight: 27,000 kg Good condition Machine can be inspected at our warehouse in 37235 Hessisch Lichtenau, test cuts possible. Currently, the hold-down devices are being resealed; the resulting price adjustment will be made in the coming days.

Condition: used, Year of construction: 1980, TUBE BENDING MACHINE LANG Hsdpfx Aorq D N Rogfeff TYPE EL90 Φ 90

Condition: new, TECHNICAL DATA type: gas-heated drive-through chamber furnace internal dimensions: (w x h x d): 2200 x 2350 x 3000 mm number of control areas: 2 Max. loading weight: approx. 2,5 t PLC: Siemens S7 Hedpfxeg Dgymo Agfoff

Condition: new, Year of construction: 2026, functionality: fully functional, workpiece weight (max.): 3,000 kg, Maximum Rotor Weight ---3000 kg (6613.87 lb) Minimum. Rotor Weight ---30 kg (66.14 lb) Maximum Rotor Diameter ---1400 mm (55.12 in) Hodpfx Agor Dd Avsfoff Minimum Shaft Diameter ---20 mm (0.79 in) Maximum Shaft Diameter ---300 mm (11.81 in) Motor power ---11 kW (14.75 HP) Drive Unit (Std.) ---11 kW (14.75 HP) Balancing Speed ---0-3000 Rpm (25 Hz) (up and down adjustable) Drive Unit --- Only Belt or Shaft / Belt + Shaft Bed length ---3000 mm (118.11 in)

Condition: as good as new (ex-display), Year of construction: 2025, Pressing area: 3000 mm x 1500 mm Hfodpfx Aeu Egp Iegfjf Operating vacuum: -0.85 bar Vacuum pump flow rate: 40 m³/h Pump power: 1.5 kW Noise level: 70 Db Heating temperature: max. 200 °C Heating power: 16 kW Machine length: 3100 mm Machine width: 1650 mm Machine height: 1750 mm Weight: 950 kg

Condition: new, Comparable to Behringer, Kaltenbach, Kasto, Jaespa, etc. Cutting range 90° Round: 260 mm Hfedpfx Agjh Tnd Aefsf Flat: 300 x 260 mm Smallest diameter: 5 mm NC-controlled, automatic material feed with hydraulic full-stroke material clamping Easy operation via NC control with plain text display Material advance function without reclamping for short section cuts Robust, linear-guided feed gripper with servo positioning for maximum precision Automatic adjustment of blade guides to material width Recommended options: Powered chip brush synchronized with blade speed Separate control panel 7" CE panel, network-compatible, up to 1000 data sets storable, history memory for various functions and data, etc.

Year of construction: 1960, condition: good (used), machine/vehicle number: 970015, Load capacity with horizontal faceplate position: 10 t Load capacity with vertical faceplate position and centre of gravity distance 300 mm: 10 t Load capacity with vertical faceplate position and centre of gravity distance 830 mm: 5.5 t Hfsdpocblc Sefx Agfef Face plate dimensions: 1500 x 1500 mm face plate speed hydraulically infinitely variable: 0,025 - 0,75 rpm Pivoting range: 0 - 135 Swivel time for full swivel range to: 140 s Swivel time for full swivel range down: 120 s Hydraulic drive: 380 V Height of swivel axis above floor: 1450 mm space requirement: 3800 x 1950 x 1800 mm Weight approx.: 3,5 t Weight of the counterweight: 2,3 t

Condition: excellent (used), Year of construction: 2006, travel distance X-axis: 8,000 mm, travel distance Y-axis: 3,300 mm, travel distance Z-axis: 1,500 mm, Manufacturer: SORALUCE Type: FS 8000 Control: HeidenHain iTNC 530 Year of manufacture: 2006 ATC Chain 40 positions Max. tool size Ø 125 x 400 mm Hfedpfx Ajxc Emxjgfof Machine prepared for rotary table Chip conveyor Central lubrication Stroke with vertical head rotated 3300 mm Specifications Metric US Standard X-Axis 8000 mm Y-Axis 2800 mm Z-Axis 1500 mm Spindle power 30 kW Spindle speed 5000 Rpm Tool holder 50 ISO/Bt/Mk X - Axis feed 15000 mm/min. Y - Axis feed 15000 mm/min. Z - Axis feed 15000 mm/min. Milling head auto-index 2.5 x 2.5 ° Dimensions (approximate) Length 17500 mm Width 4050 mm Height 5020 mm Weight 38400 kg Please note: The information on this page was provided to the best of our knowledge and, where possible, obtained from the manufacturer. The information is given in good faith, but accuracy cannot be guaranteed. Accordingly, they do not constitute representation or contractual terms. We recommend that you check all important details.

Condition: excellent (used), Year of construction: 2012, The Vertical Machining Center enables drilling, milling and cutting operations and cornering within the scope of technical capabilities indicated in the manual in details: plastic, PVC, ABS, methacrylic, polycarbonate, thermoplastic, composite, aluminum. The vertical work table allows for easy feeding and unloading of processed details and reducing the maximum size of the device to the minimum necessary. Tool change with the use of a 10-element magazine located on the side of the device, it enables various works to be carried out without the need to remove the workpiece from the table. Maximum dimensions of the processed detail: X= 4200mm Y= 1600mm Z= 20mm Rapid traverse speed (m/min): X=30 Y=30 Z=15 Set of milling heads T1 and T2: Spindle power (kW) - 3.3 Rotation speed (rpm) - max 18000 Electric spindle with clamp - ER32 Hsdpfxomzbr Sj Agfsff T3 Drill Head Assembly: Spindle motor power (W) - 370 Rotation speed (rpm) - max 2800