Gear Hobbing Machine - Vertical

PFAUTER P 630

Condition: good (used), functionality: fully functional, 840mm x 3,500mm, swing over cross slide 530mm, spindle bore 82mm, 7,1-900 Rpm, 18,5Kw, steadys, 4-jaw plate, DRO. Iiedpfx Abjxqxvvsnof

Condition: good (used), GENERAL CHARACTERISTICS Max. Ø to be ground 120 mm Grinding wheel width 250 mm Minimum Ø to be ground 1 mm Ø drive grinding wheel 304 mm Ø working wheel 508 mm DIMENSIONS AND WEIGHT Height 1,700 mm Width 1,500 mm Length 2,750 mm Weight 4,000kg ELECTRICAL CHARACTERISTICS Ijdpferpnf Aex Abnoif Grinding head motor power 15 Kw Spindle head motor power 1,8kw Hydraulic motor power 1,1kw Total power 20 kW Voltage 220/380 V

Condition: excellent (used), Year of construction: 2016, operating hours: 3,752 h, functionality: fully functional, travel distance X-axis: 1,150 mm, travel distance Y-axis: 700 mm, travel distance Z-axis: 550 mm, rapid traverse X-axis: 42 m/min, rapid traverse Y-axis: 42 m/min, rapid traverse Z-axis: 42 m/min, controller manufacturer: Heidenhain, controller model: 640, rotational speed (max.): 20,000 rpm, overall weight: 9,650 kg, spindle speed (min.): 20 rpm, spindle speed (max.): 20,000 rpm, operating hours of spindle: 1,615 h, coolant supply: 40 bar, spindle nose: SK40, number of slots in tool magazine: 120, input voltage: 400 V, type of input current: three-phase, Equipment: chip conveyor, documentation/manual, rotational speed infinitely variable, Machine in very good technical condition! Isdpfx Aszaqz Dsbneif

Condition: good (used), Year of construction: 2014, functionality: fully functional, Table surface: 850 x 400 mm Iijdpfx Abey T Nuwsnof Magnetic table: 800 x 400 x 105 mm Max. table travel (X x Y): 950 x 440 mm Max. workpiece weight: 700 kg (230 kg on the magnetic table) T-slots on the table: 3 pcs x 17 mm Distance between table and spindle center: 47,5 – 547,5 mm Grinding wheel dimensions: D355 x 38 x d127 mm Spindle speed: 1500 / 1800 rpm (50Hz / 60Hz) Spindle drive power: 3.7 kW / 4.0 kW Longitudinal travel: 3 – 25 m/min (hydraulic and stepless) Cross travel: 1 – 1000 mm/min Vertical feed rate: 1 – 1000 mm/min Minimum increment / feed amount: 0,0001 mm – 0,0002 mm Machine weight: 4000 kg Dimensions (L x W x H): 3310 x 2228 x 2710 mm Accessories / Equipment - Semi-automatic operation - Magnetic table 800 x 400 mm - Coolant system with magnetic separator - Paper band filter - Machine feet - Digital display system for the infeed / increment - Built-in wheel dresser in the spindle head The machine is being sold due to company liquidation. It is in good condition and still under power in Hungary.

Condition: reconditioned (used), machine/vehicle number: 550-235-ELD, GENERAL CHARACTERISTICS workpiece Ø max. 41 mm Range Module máx/min. 1,5 / 0.39 Rack face width 92 mm Iedsd Nw Ttepfx Abnsif Manufacturing No. 550-235-ELD Máx/min. pitch form 20/40-32/64 Maximum stroke of tools trolley 760 mm Rack length máx. 610 mm ELECTRICAL CHARACTERISTICS Main motor power 15 Cv

Condition: good (used), centerless grinding machine Iiodpfxotrguvo Abnsf

Condition: good (used), Year of construction: 2000, gear diameter: 449 mm, Equipped with: Fanuc 150MB CNC Control Dry Cutting Cutter Shroud Chip Evacuation System Auto Doors Hydraulic System Lubrication System Work light Stack Light Specifications: Largest Speed Ratio: 10:01 Work Area (Continuous): Largest Depth of Teeth: 15.24 mm Largest Width of Tooth Face: 50.8 mm Work Area Axis: Horizontal Movement X Axis: -114 - 178 mm Vertical Movement Y Axis: -178 - 190 mm Movement of the Carriage Baseplate Z-Axis: -10.16 - 500 mm Workpiece Headstock Swiveling Range B-Axis: -3 - 90 Degree Maximum Distance Machine Center to Spindle Side: 165 mm Number of Teeth: 5-200 Inclusive Max. Gear Pitch Dia. of Typical 35 Deg. Spiral Angle Gear Using Max. Cutter Dia. 12" Cutter at the Following Ratios: Iiedpfx Aeruakgsbnof Face Milling 1 x 1 - 13.5" - 342.9mm 2 x 1 - 16.0" - 406.4mm 5 x 1 - 17.7" - 450.0mm Face Hobbing (210mm Dia. Cutter) 1 x 1 - 10.560" - 268.22mm 2 x 1 - 10.286" - 275.00mm 5 x 1 - 11.810" - 300.00mm Milling Head Diameter: Helixact: 100,125,169,200,250,320mm Continuous Gumption Procedure, Teichloroethylene: 102 - 210 mm Workpiece Spindle: Drilling of Large Diameters: 5 3/64" Cone Upward Gradient on 304.8 mm (1 Foot): 21/32" Deep One of the Cone: 5.29" Diameter of the Whole Spindle Perforating: 3.35" Speeds: B-Axle Workpiece Headstock Drag Axis: 30 Degrees A-Axle Workpiece Spindle Number of Revolutions: 0 83 min-1 X-Axis Horizontal: 80 mm/sec Y-Axis Vertically: 80 mm/sec Z-Axis Carriage Baseplate: 80 mm/sec Space Requirement L x W x H (Approximate): 4.75 x 3.40 x 2.54m / 188" x 134" x 100" Machine Weight (Approximate): 10980 kg / 24,156#

Year of construction: 1994, condition: excellent (used), machine/vehicle number: 04.2398, Manufacturer: Arthur Klink Type: RIW 10 x 1500 x 500 Machine No.: 04.2398 Iedpfxjgyd T Eo Abneif Year of construction: overhauled by manufacturer 1994 weight: 3700kg tractive force: 10.000kg (100kN) max. stroke: 1500mm max. workpiece diameter: Ø 500mm clearing speed: infinitely variable from 1m/min to 6m/min return speed: stepless adjustable up to 20m/min power supply: 400V / 50Hz

Condition: used, Swing Diameter Over Bed: 400 mm Swing Diameter Over Longitudinal Slide: 350 mm Distance Between Centers: 610 mm Travel Limit: 240 mm Suggested Workpiece Diameter: 200 mm Iijdjxg Nd Aspfx Abnsf Max Longitudinal Travel: 560 mm Machining Length: 550 mm Max Cross Travel: 40 mm + 120 mm Height of Spindle Axis from Floor: 1135 mm Programmable Spindle Speed Range: 40 to 4000 rpm Spindle Bore Diameter: 52 mm Spindle Interior Cone: MK 6 Slide/Bed Slope: 45/45° Turret Positions: 12 Tools Main Motor: 15 kW Control: Fanuc 6T Equipped with: See photos

Condition: good (used), Year of construction: 2009, max. wheel diameter 1200 mm Iedpfxswzmpzs Abneif gear width 260 mm max. module 16 min. module 0,5 stroke 270 mm distance between table/spindle 920 mm taper of shaper cutter SK control Bosch MTX table diameter 900 mm min. workpiece diameter-at internal hobbing 1200 mm strokes - infinitely variable 50-1000 Hub/min spindle diameter 125 mm table hole 320 mm Distance of shafts Min/Max 0-820 power capacity Stosskopf 30 KW total power requirement 72 KVA weight of the machine ca. 24 t dimensions of the machine ca. 6,5x2,9x4 m Liebherr LH 90 control, 9 axis CNC, top condition.