Ring & profile bending machine

Ostas OPK 42

Condition: new, Year of construction: 2026, shaft diameter: 50 mm, - Shaft diameter 50 mm - Rotates clockwise and counterclockwise - Suitable for horizontal/vertical use Lodjwv Ufaepfx Adwjhg - Foot control - Emergency stop - Documentation - 400V

Condition: new, Year of construction: 2024, machine/vehicle number: 302340, Profile Bending machine KB Türkei Lodpjd S Uf Sofx Adwehg model MB 30 bottom shaft 30 mm top shaft 35 mm two rollers driven with basement capacity: up to round tube 48 x 3,0 mm flat material 50x10 mm square tube 40x40x3,0 mm weight 170 kg motor 0,75 kw 400 Volt 50 Hz 3 ph.

Condition: new, capacity 90 degrees: round 510 mm capacity 90 degrees: square 450 mm 650x450 band speed 15 - 100 m/min table height 844 mm dimensions of saw-band 5320 x 34 x 1,1 mm total power requirement 3,0 kW weight of the machine ca. 2,1 t dimensions of the machine ca. 1,9 x 2,87 x 1,3 m PROMOTIONAL PRICE!!! 2-column double miter band saw K-tech DG 62/45 HA-I • 2-column miter saw • Solid, yet easy to use • Material height sensor (automatic cut start detection) • Smooth running thanks to diagonal cutting, feed regulator + cutting pressure regulator • Solid material inlet roller • Removable chip tray (disinfection) Lheded Iipmepfx Adwog • Energy-saving and low-vibration thanks to diagonal cutting • Control panel ergonomic, safe and free-standing • Frequency-controlled saw drive 15 -100 m/min. • Hydraulic cutting pressure control valve • Hydraulic control of saw frame and vice • LEDs for monitoring all safety functions • Large-sized wheels (520 mm) a. • Clear miter adjustment up to 60° Semi-automatic function: 1. Tension the material 2. Saw starts 3. Lowering in rapid traverse to the beginning of the material or the same for series cutting cut 4. Saw blade off 5. Raise the frame until it is just above the material 6. Vice opens

Condition: good (used), Year of construction: 2002, machine/vehicle number: V020113, operating hours: 43,000 h, AMADA MODEL HFT 8025 80 tons capacity x 2500 bending length hydraulic downstroking press brake complete with cnc control, Model Amada HFT 8025 downstoke CNC Press brake Year 2002 Tonnage 80 KN Controlled Axis Y1, Y2, X, R Max. Bend Length 2500 mm Open height 470 mm Approach Speed 100 mm/sec Bending Speed 1 - 10 mm/sec Return Speed 1-100 mm/sec Oil Capacity Motor Power 9kw Weight 5750 kg Bed Length 2500 mm Bed Width 180 mm Open Height 470 mm Lsdpfxeuwktno Adwshg Throat Depth 420 mm CNC Control

Condition: new, Year of construction: 2025, Pressure blasting cabin DSK 11.11.30. Blasting chamber W=1050 D=1050 H=955mm. 1 TÜV-tested pressure vessel 30l with conical outlet funnel. 1 blasting medium dosing valve with blasting medium quantity regulation pneumatically controlled. 1 built-in closing cone with guide tube. 1 compressed air connection with pneumat. Shut-off valve and branch for control air. 1 pressure regulator to adjust the blasting pressure. 1 blasting hose DN19. 1 handpiece with boron carbide blasting nozzle Venturi 8mm. 1 pair of blasting gloves. Electrical height adjustment of the cabin for body-friendly posture. Memory position storage for 3 heights. Dust extraction filter 2000m³/h 2,2kW. Lhjdpfx Adega Ehbeweg

Condition: used, Year of construction: 1970, machine/vehicle number: 120895, pressure:63 t throat:250 mm stroke:8 - 100 mm no. of strokes:120 Hub/min table::715 x 500 mm Lsdpfjfx Hv Hjx Adwjhg dayligth:330 mm ram adjustment:63 mm clamping plate:700 x 480 mm hole in the table:240 mm Hole in clamping plate:110 mm dimension of ram:450 x 280 mm weight of the machine ca.:5,5 t dimensions of the machine ca.:1,2 x 1,7 x 2,7 m hydraulic tilting single column eccentric press, tilting in 4 steps, opening to rear (325 x 500mm) and below (360x160mm) with central lubrication via hand pump, additional clamping plate 700 x 480 x 850 mm, two-hand operation, foot-trip operation possible, operating-mode selector for adjustment of continuous or single stroke, emergency cut-off, piece counter, various accessories

Condition: good (used), Year of construction: 1990, machine/vehicle number: 5211, Offer 24289 Technical data: - max. cutting width 3060 mm - max. cutting capacity at 45 Kp/mm² 4 mm - Cutting angle 1.50 ° - Cutting gap - adjustment via adjusting screws - Number of hold-down devices 15 pcs - Stroke rate 23 to 43 /min Lhedpet Ucgaefx Adweg - Front angle stop - Motorized backgauge position-controlled 15 - 850 mm - Cutting line lighting - E - foot switch - Drive 400 V / 7.5 kW - Space requirement approx. W 3900 x H 1600 x D 2400 mm - Weight approx. 4.5 t

Condition: new, capacity 90 degrees: round 240 mm capacity 90 degrees: square 240 mm 165 x 310 mm saw band length 2725 x 27 x 0,9 mm mm table height 890 mm band speed 35 / 70 m/min total power requirement 1,1 kW weight of the machine ca. 0,35 t Dimensions (LxWxH) 1,7 x 0,75 x 1,8 m The Z252/DG has the following equipment: - hydraulic cylinder, - emulsion pump, Ledpfohpktvox Adwjhg - eccentric clamp, - base, - saw blade, - 400V plug -16A- The machine is delivered fully assembled and ready for immediate use.

Year of construction: 2004, condition: excellent (used), Four-side planer -max. planing width 23cm Lhjdpfxjhlp D Ne Adwjg -max planing height 16cm -2 pulling rollers in the table -chromed table - smooth regulation of the feed speed -2 pulleys from the top in front of the lower head, additionally a roller apparatus for short elements - 4 spindles: lower 5.5kW, right 5.5kW, left 5.5kW, upper 7.5kw The machine is in very good condition, little used, with spiral heads on the bottom right and left, with a Terssa knife head on the top.

Condition: good (used), Year of construction: 2012, functionality: fully functional, travel distance X-axis: 3,000 mm, travel distance Y-axis: 2,000 mm, power: 13 kW (17.68 HP), It is a LEVIBRETON ONE, surface sanding machine The machine has a wobble head and a 750mm diameter grinding disc. The machine can be used to polish the surfaces of hard stone and soft stone (marble). Ljdpfxorpi E Aj Adwehg polished, satinized and bush-hammered with the appropriate tool.