Double mitre crosscut saw

OMGA TRF 527

Condition: used, Year of construction: 2023, DOUBLE GLASS BEAD SAW TRF 527 VIS CE 1 pc DOUBLE GLASS BEAD SAW TRF 527 VIS CE TRF 527 VIS: Double miter saw for the simultaneous cutting of two glass beads positioned one above the other. The right saw unit is fixed, adjustment of the left unit is via the set cutting length can be read off a digital display. The units have supports that allow two glass beads to be cut simultaneously. The upper support can be removed for cutting larger cross-sections. After the cutting process is completed, the pneumatic clamping cylinders automatically swing to the side to simplify loading and unloading of the machine. STANDARD EQUIPMENT • Fixed unit on the right • Digital dimension display • Pressure switch • 2 HM-tipped saw blades • Electrical system with motor brake, undervoltage release, motor protection switch • Pressure switch • Tool set • Guards with horizontal clamping devices, pivoting • Two-hand control • Belt drive • Pneumatic unit lift • Middle support TECHNICAL DATA • Motor power 2 x 1.2 kW • Saw blade diameter Ø 220 mm • Max. cutting height without support 80 mm • Max. cutting width at 90 degrees 55 mm • Max. cutting width at 45 degrees 40 mm • Max. cutting length 2800 mm (optional 4000 mm) • Min. cutting length 158 mm • Weight 217 kg • Space requirement (standard equipment) 3000 x 850 mm Extended cutting capacity 1 pc Maximum cutting length • 4000 mm Star stop 4 positions 1 pc set 2 mechanical stops for adjusting up to 4 intermediate angles. Additional center support. 1 adjustment for rebated profiles. 1 adjustment for rebated profiles as per drawing: - Attachment to the clamping devices to compensate for the profile inclination - Allowances on the rear stops of the units and the center support. The sketch below shows (in green) a beveled presser that follows the inclined profile and presses it against the allowance on the stop (shown in red). Ljdpfxexnlgcs Apvsrl Storage location: Garbsen

Condition: as good as new (ex-display), Year of construction: 2025, Pressing area: 3000 mm x 1500 mm Operating vacuum: -0.85 bar Vacuum pump flow rate: 40 m³/h Ledpeu Egp Isfx Apvsrl Pump power: 1.5 kW Noise level: 70 Db Heating temperature: max. 200 °C Heating power: 16 kW Machine length: 3100 mm Machine width: 1650 mm Machine height: 1750 mm Weight: 950 kg

Condition: used, Year of construction: 2002, DOUBLE MITRE SAW (GLASS BEAD SAW) OMGA TRF 527 NC incl. star stop Year of manufacture: 2002 Min. & max. distance between units: 158 mm, 2800 mm Cutting capacity at 90 degrees: 55 mm Cutting capacity at 45 degrees: 40 mm Max. cutting height: 40 mm Motor power: 2 x 1.18 kW Saw blade bore: 30 mm Saw blade diameter: 220 mm Ledpoxwumqsfx Apvorl Spindle speed: 5000 rpm

Condition: new, A twin blade saw that has been specifically designed for cutting glazing beads accurately to length, with either a straight or mitred cut. The machine has two work-levels one set above the other, allowing two lengths of beading to be cut simultaneously. The two lengths of bead are held secure during the cutting operation by the front pneumatic clamps. Setting the correct length is achieved by means of handwheel moving the left head in relationship to the fixed right head, the length is easily read from the mechanical digital display. Min/Max. cutting length 150mm - 2400mm Max. cutting section at 90° 55 x 100mm Lodjdy Hqvspfx Apvorl Max. cutting section at 45° 40 x 100mm 2 x sawblades dia. 220mm x 30mm bore Motor 1.6hp, 3 phase CE Safety requirements

Year of construction: 1977, condition: refurbished (used), I sell the double mitre saw Rapid DGS, year 1977. Tilting heads Drilling front heads on each side included Very good condition. Lroded N Rb Djpfx Apvjl Available immediately.

Condition: new, Year of construction: 2026, Size: 6 Nominal heat output: 170kW -- BImSchV stage 2 and CE conform-- combustion chamber completely fireclayed Lsdpfodlhdbjx Apvsrl For rooms of: 4.800 m³ (according to DIN) Fuel: logs, chipboard, chips, chip briquettes fuel consumption: 40 - 50 kg/h Blower air capacity, free blowing: 14.000 m³/hour Outlet opening: Ø 700mm Flue pipe connection Ø 220 mm Weight: 2.150 kg SPS control cabinet: 380 Volt

Condition: as good as new (ex-display), FULL LINE of Double-side Sizing-Milling & Edge Banding. Composed of the following machines: VZ0200A) Gantry-portal Loader (Double pick-up station) "BARGSTEDT" Mod. TBH 500/D/30/12 VZ0200B) 1st Double-side Sizing & Edge Bander "HOMAG" Mod. KFL 525/8/A3/15 VZ0200C) In-feeding Rollerway "HOMAG" Mod. TDL 310/30/12 with 90° Turning device (from lenghtwise to crosswise) with double cone system Lrjdsdt Rgvopfx Apvel VZ0200D) 2nd Double-side Sizing & Edge Bander "HOMAG" Mod. KFL 526/10/A3/30 VZ0200E) In-feeding Rollerway "HOMAG" Mod. TDL 510/25/12 with 90° Turning device (from crosswise to lenghtwise) with double cone system VZ0200F) Cleaning machine "WANDRES" VZ0200G) Gantry-portal Stacker (Double pick-up station) "BARGSTEDT" Mod. TSP 410/D/25/12

Condition: excellent (used), Four side planer scm compact xl - planing width 23cm Lrjdpfx Apelat Hdsvjl - planing height 13cm -electric lifting of the upper head and feed rollers - all spindles adjustable vertically and horizontally - bottom 4kW, right and left from one motor 7.5kw kW, upper 5.5kw universal 5.5kw Machine in very good condition

Year of construction: 2014, condition: good (used), For sale is a Nilfisk compact safety industrial vacuum cleaner type CTS40 M Z22 400 C 4 kW 9 A 50 Hz 114 kg Ex-proof The vacuum cleaner is in good condition and ready for immediate use Machines purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES ETC. Do you need a high quality but inexpensive metalworking machine for your production? Or do you want to sell yours? Lredpohu Sf Hofx Apvol For more information or to contact us please visit our website

Year of construction: 2014, condition: used, PROLOGIC window construction software Lrsdpjrci S Sjfx Apvel FenOffice 14 Conturex