Used Welding Force for sale (11,645)

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Gedpfx Aszuzw Djk Ueug Year of manufacture: 2017 Technical data: Motorized loading table 3,500 x 1,600 mm for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Specific pressure (on 80% of the area): 2.27 kg/cm2 Pressure cylinder: 12 x 80 mm Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. The press plates consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Exit side from the press: 1,600 mm. Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: refurbished (used), DALEX seam welding machine, transverse seam version Outreach: 350 mm Rated power: 160 kVA Secondary short-circuit current: 38.5 kA Secondary open-circuit voltage: 4.8-9.6 V Electrode force: 140-2,040 daN with 2-stage switch and auxiliary control unit with thyristor power stage and synchronous welding control MPS 100 multi IMPORTANT NOTE – PLEASE PAY ATTENTION Guodpfodx Suhox Ak Ujg The above-mentioned performance data comes from the machine's nameplate. During inspection of the machine, it was found that a 200 kVA welding transformer had been installed by the previous owner. This changes the performance data.

Condition: good (used), Year of construction: 2017, operating hours: 494 h, functionality: fully functional, machine/vehicle number: 27026757, type of input current: three-phase, total height: 510 mm, total width: 300 mm, total length: 706 mm, input voltage: 400 V, ground cable length: 5,000 mm, overall weight: 100 kg, type of cooling: water, hose package length: 1,200 mm, electrical fuse: 35 A, open-circuit voltage: 73 V, welding current at 60% duty cycle: 360 A, welding current at 100% duty cycle: 320 A, input current: 26 A, protection type (IP code): IP23, welding current (min.): 3 A, welding current (max.): 400 A, input frequency: 60 Hz, Equipment: type plate available, Fronius TPS 400i Pulse MIG/MAG welding system – complete with accessories For sale: Fronius TPS 400i Pulse professional MIG/MAG welding system, complete with wire feeder, mobile stand, and a comprehensive set of accessories. The Fronius TPS 400i Pulse is a professional welding machine suitable for a wide range of MIG/MAG applications. The machine features pulse welding and the ability to record welding data (datalogging). This datalogging is a built-in function of the welding machine and is not a separate accessory. Included with the machine: - Fronius TPS 400i Pulse - Fronius wire feeder, without stand - Sturdy mobile stand for the power source - 1.2-meter intermediate cable pack, currently connected Gujdezwhprjpfx Ak Ueg - 20-meter intermediate cable pack, supplied as extra - 8-meter Push/Pull welding torch - Wera torque screwdriver, for correctly tightening the push/pull wire feed rollers - Box with various wear parts, including contact tips, gas nozzles, and other accessories - Ground cable with welding clamp - Connecting cables and other cables/hoses - Other accessories as shown in the photos - Manual available digitally Versatile professional system The combination of the 1.2-meter intermediate cable pack, the supplied 20-meter intermediate cable pack, and the 8-meter Push/Pull torch makes this system highly versatile for welding aluminum, among other applications, and for larger structures or workpieces where the welding machine cannot be placed directly next to the workpiece, the set offers a great deal of flexibility. The built-in welding data recording/datalogging is of interest to professional users who value process monitoring, quality control, and traceability of welding work. The machine has been used and has normal signs of wear, but is in good and solid condition. Sold as a complete set as shown. Inspection and testing are possible by arrangement. Pick-up only, shipping not possible. A forklift is available.

Condition: ready for operation (used), Year of construction: 2025, Kaiser Press 50 -Exhibition machine / 0 operating hours -Electro-hydraulic drive -Operation: foot pedals and push buttons on the control panel -Maximum pressing force: 50 tons -Power consumption: 0.75 kW -Voltage: 230 V -Frame width: 930 mm -Maximum frame width including hand crank and electrical unit: 1300 mm -Overall height: 1900 mm -Cylinder stroke: 145 mm plus 60 mm threaded spindle Gedpfx Aoztfbwjk Ujug -Usable width – working area inside: max. 750 mm -Usable height – working area: 0 mm to 780 mm -Frame depth: 220 mm -Overall depth with base: 535 mm (can be fastened to the floor) -Support depth of the height-adjustable work table (crossbeam): 245 mm -Crossbeam adjustable in 6 positions (hole spacing: 140 mm) -Height adjustment of the crossbeam via hand crank (no manual lifting required) -Hydraulic unit can be moved laterally: 300 mm (ball-bearing mounted in the upper guide area) -Includes 8 punches with integrated holder: -2t with Ø9.8 mm -3t with Ø11.7 mm -6t with Ø15.7 mm -8t with Ø17.7 mm -10t with Ø19.8 mm -12t with Ø21.8 mm -13t with Ø24.8 mm -15t with Ø30 mm -Welded construction -Includes work light to illuminate the working area -Pressure gauge with pressure display -2 prism supports included -Automatic piston retraction -Integrated tool tray in the lower area of the press Dimensions: L x W x H 0.9 x 0.3 x 1.9 meters / Weight 255 kg Errors and omissions excepted.

Condition: used, Year of construction: 2012, Used machine Year of manufacture: 2012 Base machine - Dynestic 7521 20.6 Dynestic table For classic nesting machining with wear plate Machining length 6250 mm (DYNESTIC 20.6 additional 4th stop in Y already included) Machine frame in welded construction with ground and hardened prism guides for the traversing carriage, spindle head and consoles Traversing carriage in gantry design Rack and pinion drive, helical, in X and Y direction, ball screw spindles Z-axis for precise positioning Technical data: The technical data refer to the DYNESTIC 7521 - 20.6 Please refer to the corresponding data sheets. Machining dimensions: Max. workpiece size for edge machining X = 6250 mm Y = 2100 mm Max. travel distances X = 7360 mm Y = 2720 mm Z = 325 mm Max. clearance height DYNESTIC table Z = 1st stage 318 mm / 2nd stage 418 mm from top edge of table (without tool, without chuck) Maximum programmable speed Vector speed: 128.0 m/min X = 80 m/min, Y = 100 m/min, Z = 25 m/min 4-stage extraction hood with pneumatic height adjustment and viewing window Voltage 400 V, 50/60 Hz CONTROL: Dual-Core processor Operating system Windows XP 80 GB hard drive / 1 GB RAM RJ45 network connection 10/100 Base-T Fast Ethernet US keyboard and Microsoft IntelliEye mouse (optical) CD-ROM / CD-RW drive (CD burner) Remote maintenance Integrated network card for data transfer of control and program data. Data transfer takes place via high-speed internet connection Requirement: High-speed internet connection at the machine. DYNESTIC table Solid, continuous machining table with grid division, continuous grooves in X and Y direction, groove spacing 50 mm with 25 meters of sealing cord for securing the wear plate 1 machining field with stop rails / stop Height 30 mm, pneumatically lowerable 2 stop rails in Y direction and 1 stop in X direction on the right (when viewed from the front of the machine) Vacuum fields 1-circuit vacuum system Boring unit 7976, 24 spindles Drive power 3.0 kW 18 vertical spindles individually selectable Arrangement in L-shape, 10 in X and 8 in Y direction 32 mm grid Max. drill diameter: 35 mm Total drill length: 70 mm from the mounting end (depending on plate thickness) Spindle extension stroke: 70 mm Rotation direction: alternating right-hand / left-hand rotation n(max.) 1000 - 5710 min-1, steplessly adjustable Chuck: M 10 thread - clearance fit 11 mm without tool, without chuck 6 horizontal spindles 2 double boring spindles in X direction (32 mm distance between 1st and 2nd horizontal boring spindle) 1 double boring spindle in Y direction Chuck: M 10 thread, clearance fit 11 mm Total drill length max. 70 mm from the mounting end without tool, without chuck Free space 1 for: Optional double boring spindle in X direction Gedpfsw I U Ecsx Ak Ujug or Vertical adapter with double feed force Free space 2 for: Optional saw in X direction or Vertical adapter with double feed force Milling unit 7831, 2-stage Power: 11.0 kW (S6) n(max.) = 1000 - 24000 min-1, steplessly adjustable, two-stage feed stroke max. power at 12000 min-1 to 24000 min-1 air-cooled with HSK-F 63 tool holder with right-hand

Condition: good (used), Year of construction: 2015, functionality: fully functional, pressing force: 2,500 t, table width: 2,500 mm, table length: 5,000 mm, total length: 8,000 mm, total width: 8,000 mm, total height: 9,000 mm, overall weight: 55,000 kg, Equipment: safety light barrier, LOIRE SAFE Hydraulic Press – High-Performance System for Toolmaking and Heavy-Duty Forming This high-performance hydraulic press in a robust 4-column gantry design has been specifically engineered for demanding applications in toolmaking (tryout/spotting) as well as for large-format forming processes. The stress-relieved, annealed welded construction ensures maximum rigidity and long-term process stability. Guedpfxoyw Ah Es Ak Ujg The machine is equipped with three main cylinders featuring multi-cylinder parallel control, achieving high repeat accuracy within ±0.1 mm. Its powerful hydraulic system, based on Bosch Rexroth components, operates at a maximum working pressure of approximately 450 bar, enabling precise and forceful processing. Control is provided via a Siemens S7-317F PLC, combined with servo-controlled axes (Rexroth MLC) and visualization via Siemens WinCC. This setup allows for fully programmable press cycles, storage of tool parameters, and user-friendly operation with diagnostics and fault monitoring. In terms of safety, the press is comprehensively equipped: light curtains at the front and rear (Category 4), ram parallelism monitoring, emergency stop with defined response time, and optional two-hand operation ensure maximum operational safety. The system is CE-compliant and meets current safety standards. Features include a hydraulic, three-section draw cushion, a hydraulic ram cushion, as well as a movable table with approximately 4,000 mm stroke. The machine is complemented by a DIN-standard ram plate and integrated cutting impact damping for challenging forming processes. Toolmaking (Tryout / Spotting)

Condition: used, Year of construction: 2018, Nominal pressing force: 4,000 kN Ram stroke, adjustable in increments: 30 ... 160 mm Ram adjustment: 180 mm Throat depth: 515 mm Strokes per minute (idle): 45 / min Option: Infinitely variable stroke rate: 10 … 60 / min Die installation height at maximum stroke, bottom dead center, and ram fully raised: 660 mm Table clamping surface (W x D): 1,700 x 1,000 mm Table height above floor: 1,005 mm Ram clamping surface (W x D): 1,100 x 800 mm Pin bore in ram: 65 mm Main motor power: 45 kW Approximate machine height: 4,325 mm Machine weight: 33,000 kg Control system – Press safety control with redundant design and self-diagnosis, featuring plain text status and error display Guedew Rbxzjpfx Ak Uog Infinitely variable stroke rate in the range of 10 ... 60 strokes/minute via ABB frequency inverter Control variant: TFT color touchscreen including electronic cam controller with die management and die protection, with color touchscreen visualization, SIEMENS PLC S7-300, die data management, counting systems, data transmission via Profibus Fully automatic stroke adjustment / ram adjustment Rigidly welded tie rods, clear distance between tie rods: 1,345 mm Swiveling main control console Non-contact safety guard – BWS brand LUMIFLEX, mounted at the front of the machine table or die area, installed on the tie rods

Condition: used, Year of construction: 2006, with automatic lifting table feeding system with 4 precision spindles, ensuring the stack is always held evenly at the correct level. Equipped with 4 powered roller groups. Lifting table dimensions: 6000 x 2200 mm. Feeding side: left (from the operator's perspective). Max. stack height: 450 mm. Lifting table height (bottom): to be defined. Speed for lifting and lowering: 0.7 m/min. Lifting table drive: 3 kW. Powered roller group: 4. STANDARD CONFIGURATION. Usable cutting length: 6000 mm. Lifting table feeding: Yes. Working height: 950 mm. Saw blade overhang: 100 mm. Clamping device opening: 117 mm. Machine control: G Drive RT. Number of clamping devices movable in X: 1. Number of clamping devices movable in X and Y: 1. Number of fixed clamping devices: 1. Min. material thickness (with side alignment): 10 mm. Min. material thickness (with lifting table feeding): 10 mm. Min. panel dimension (with lifting table feeding): 2400x1200 mm. Max. panel dimension (with lifting table feeding): 5500x2070 mm. Max. panel dimension (without lifting table feeding): 5800x2010 mm. Safety device according to CE: included. Supply voltage: 400 V / 50 Hz. MACHINE CONFIGURATION. Machine bed: The machine bed structure made of steel is welded using arc welding and then milled and finished on CNC machines. The rigid structure of the machine bed guarantees both high cutting quality with high cutting speed, as well as the enormous durability of the entire machine. Saw blade overhang: 100 mm. Power of main saw motor: 7.5 kW. Power of scoring saw motor: 2.2 kW. Diameter of main saw blade: 400 mm. Diameter of scoring saw blade: 215 mm. Feed rate of saw carriage: Forward: 1-170 m/min. Return: 170 m/min. Motorization of saw carriage feed: Servo drive. Diameter of dust extraction port (bottom, 1x): 200 mm. Diameter of dust extraction port (top, 2x): 115 mm. Thanks to the rigid machine bed construction, the masses are distributed in the best possible way, which prevents twisting and thus guarantees an absolutely vertical run of the saw blade. Machine table made of steel with individual, removable support elements made of high-quality, durable material. The saw carriage runs on two round guides, which are mounted horizontally on one level. Large prism rollers (diameter 86 mm), with spring-loaded counter rollers, ensure smooth linear feed, as well as very low contact pressure and enables virtually wear-free operation of the saw carriage. The weight and forces acting on the saw carriage are evenly distributed on the two guides (50/50) and on each individual prism roller. The saw carriage runs absolutely without lubricant on the guides. The two guides are located away from the cutting line, outside the direct dust area. The diameter of the guide rods is 40 mm, making them the largest and most stable guides used in this sector. Pneumatic quick clamping system; for quick and convenient tool changes. This system is extremely reliable in operation, as it is mechanically clamped via a flange with a bayonet lock and spring force and unlocked via a pneumatic quick coupling. The flange must be rotated by approx. 10° in order to remove it. Due to excellent accessibility and the fact that the operator does not need any other tools, the tool change is very easy and can be carried out in seconds. The scoring saw adjustment is made from the outside. Gsdpezn N Ikefx Ak Ueug

Condition: new, Year of construction: 2025, Technical Specifications: Guedotmfzuepfx Ak Ueg Model: KMD20 Operated: Motorized Pressure Input: Up to 6 bar Power: 20KVA Welding Capacity: 1.5+1.5mm mild steel Maximum Force(6 bar): 115daN Input Voltage: 380V/50Hz Protection Fuse: 63A Seam Weld Arm Length: 200mm Cooling: Water cooling (8L/min) Power Input Cable: 3m Protection Class: IP21 Power Level: %0-99 power adjustable by controller Weld Time: 1-99 Cycle adjustable by controller Dimensions (W/L/H): 450m x 1000mm x 600mm Weight: 203Kg

Condition: used, total width: 30,000 mm, Year of construction: 2006, Equipment: ABS, Goldhofer STZ-H6-57/80A Telescopic Lowboy Trailer for Wagon Transport                                 Approval          Technical 1 Speed:      80 km/h                65 km/h Fifth wheel load:                23,000 kg              26,000 kg Rear axle load:        10,000 kg              11,000 kg Total weight:      83,000 kg              92,000 kg Payload:                  52,500 kg              61,500 kg Tare weight: (without accessories):          30,500 kg Gooseneck: Length: 4,000 mm Width: 2,480 mm Height: 235 mm Fifth wheel height: 1,350 mm DLR front: 1,420 mm DLR rear: 2,700 mm Kingpin: 3.5 inches Inclination: angled 10 degrees Front corners: angled 45 degrees Decking: Spruce 50 mm Fifth wheel supports: mechanical Width with sideboards: 2,550 mm Hydraulic STZ gooseneck with external beams, hydraulically raisable and lowerable with mechanical drop-side supports and hydraulic lowering cylinders Hydromechanical forced steering (2-circuit steering) in a flat design (height 235 mm) with adjustable guide elements and THP steering cylinders. Loading platform: Type: Platform Liftable: no Length: 13,000 mm Width: 3,000 mm Decking: Sheet metal/Spruce 50 mm Wheel recesses: no Extensions: no Extendable: single telescopic Length1: 10,000 mm Loading heights (loaded) Loading height 1: 815 mm Telescopic loading platform, designed as an outer and inner tube structure, with a 1,070 mm long, fixed loading platform section at the front. Integrated bolt-on coupling in the fixed loading platform section for connecting tank bridge extension beams; the welded track rails serve as a rail track in the track gauges of 1,000 mm (rail spacing 1,015 mm) and 1,435 mm (rail spacing 1,450 mm). Locking of the extension stages by means of spring accumulators and conical bushings Loading platform height on the frame center tube (outer tube) approx. 815 mm (+/- 130 mm) Gjdpfx Akeyfvf So Ujug Loading platform height on the embedded rail elements approx. 790 mm (+/- 130 mm) Rear axle: Axle design: Standard Loading height, loaded: 815 mm Width: 3,000 mm Wheelbase: 1,360 mm Decking: Sheet metal Extensions: no Wheel recesses: no Excavator recess: no Axles: Number of axles: 6 Lift axle: see accessories Axle type: Steered stub axles Axle equalization: hydraulic Axle manufacturer: BPW/Eco Operating positions: 1 Axle travel (1) +/-: 130/130 mm Axle travel (2) +/-: 0/0 mm Raising/lowering valve: Yes 1st axle pneumatically liftable with lift bellows Steering: Number of steered axles: 6 Steered axle arrangement: all steered Maximum steering angle: 45° Steering type: Hydraulic 2-circuit Tires: Dimension: 235/75 r 17.5 143/141 J Tire type: Twin Rim type: Disc Rim centering: Center-centered Brake code: According to EU standard: Yes ABS: Yes ALB: Yes EBS: Yes with ABS connection spiral: No Parking brake: Spring accumulator EBS: No ECAS: No Note: Brake calculation no.: GH 4324S Chassis note: Steering designed for the extended state with a larger steering angle of the front axles Open wheel cutouts above the wheels with narrow transverse outriggers in between (aluminum covers, see accessories below) Control elements protected on the left in the direction of travel...

Condition: used, Year of construction: 2003, operating hours: 6,659 h, functionality: fully functional, KraussMaffei injection molding machine KM 300-1400 C2, manufactured in 2003, with extensive peripherals and material supply system. Manufacturer: KraussMaffei Machine type: KM 300-1400 C2 Designation on control panel: KM 300-1400 C2P International size designation: KM 1400 C2/300 Machine type: Injection molding machine Year of manufacture: 2003 Machine number: 61004124 Machine weight: 14,370 kg Gjdjz Apkuopfx Ak Ujug Operating hours according to display: 66,598:20 h Control system: KraussMaffei Material supply / dosing: Colortronic UB95 Temperature control / cooling unit: Frigel Microgel RCM80/6HP Year of manufacture Frigel: 2013 Voltage Frigel: 400 V Auxiliary voltage Frigel: 110 V Frequency Frigel: 50 Hz Max. current Frigel: 17 A Refrigerant: R407C Refrigerant fill quantity: 2.4 kg Temperature range Frigel: -5 to +90 °C Weight Frigel: 200 kg Additional peripherals: Second Frigel Microgel unit, material conveying system, discharge conveyor, and rotary table available.

Condition: ready for operation (used), Year of construction: 2000, functionality: fully functional, pressing force: 100 t, stroke length: 100 mm, throat depth: 400 mm, overall weight: 6,000 kg, working length: 3,000 mm, TECHNICAL DETAILS Axes: 5 Pressing force: 1,000 kN (100 t) Maximum bending length: 3,000 mm Distance between side supports: 2,600 mm Overhang: 400 mm Stroke: 100 mm Installation height: 370 mm Gsdpfjzxnggsx Ak Uoug Number of cylinders: 2 Rapid traverse: approx. 85 mm/s Working speed: 10 mm/s Return speed: approx. 80 mm/s MACHINE DETAILS Oil filling capacity: approx. 85 l Motor power: approx. 10 kW Dimensions & Weight Dimensions (L x W x H): approx. 3,300 x 1,930 x 2,325 mm Machine weight: approx. 6,000 kg

Condition: new, *IMMEDIATELY AVAILABLE* Includes: Hydraulically Lowerable Equipment: -8 lashing eyes -V-drawbar -Manual hand pump Net: €3,441.18 / Gross: €4,095.00 Article number: FBA113281610.01 Technical Data: • Brand: Vezeko • Model: Husky FB 13.28 • Vehicle type: Lowering trailer • Vehicle condition: New • First registration: Without first registration • TÜV/HU: 2 years from first registration • Internal dimensions (LxWxH): 272 x 162 x 10 cm • External dimensions (LxWxH): 434 x 228 x 70 cm • Loading height of the floor: 48 cm • Permissible total weight: 1,300 kg • Tare weight: 385 kg • Payload: 915 kg • Chassis: Low-loader (wheels next to the body) • Tires: 165R13C • Suspension: ALKO rubber spring axle • Support wheel: Yes • 100km/h approval: Optional, can be retrofitted DESCRIPTION • 15mm multiplex floor panel, made of birch wood, with non-slip coating - extremely robust • Side walls made of anodized, double-walled aluminum profile 10cm • Insertion options at all corners for e.g. tarpaulin frame • Very stable steel frame welded • Frame completely hot-dip galvanized • Many stable cross members, resulting in high point load capacity • Loading area hydraulically lowerable, license plate holder at the rear, can be swung away for loading • Mechanical safety lock of the pivoting axle during operation • With rear overrun protection • Additional longitudinal struts continuously welded in • Tool box at the front • 8 lashing eyes inside the V-loading rail, rubber-coated, tensile force (750DaN/kg) • ALKO overrun device and parking brake • ALKO coupling head • Very stable V-drawbar, REINFORCED • Reverse drive automatic • 13-pole plug • Reversing lights • Large-sized safety lighting • Integrated rear fog light • Rear position lights in LED • Lighting recessed in the rear frame • Support wheel with clamp in the center _____ Accessories can be retrofitted by our specialist workshop!! - Please feel free to request specific features! _____ - Financing or leasing possible - Delivery throughout Germany possible - All prices include VAT. - Vehicle registration document can be sent in advance, or transfer license plates (Germany) can be provided. - Export license plates incl. customs registration possible Descriptions and images are protected by copyright!! Anhänger Zentrum BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Gedpfjzy Dh Njx Ak Uoug Over 1,200 trailers immediately available for you! We have been Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix - specialist dealer & repair - workshop for over 30 years. - Subject to errors, omissions and prior sale -

Condition: used, Spot welding machine, projection welding machine DALEX type PL 63 Serial No. N-0051390 Year of manufacture 2018 Output at 50% duty cycle: 63 kVA Output at 100% duty cycle: 44.5 kVA Maximum welding power: 182 kVA Rated welding current: 8.77 kA Throat depth: 250 - 550 mm Maximum arm spacing: 150 to (310 mm) Upper electrode arm diameter: 50 mm Lower electrode arm diameter: 60 mm Electrode holder diameter: 25 mm Electrode stroke max.: 65 mm Guedpoycv Sasfx Ak Ueg Electrode force: 100 - 600 daN Operating air pressure: 1 to 6 bar Power supply: 400 Volt, 50 Hz Rated current: 158 A Connected load: 137 kVA - Thyristor power stage - Welding control HARMS+WENDE - HWH MPS 10β - 5-stage control, single spot, series spot, 8 programs - Electrode force infinitely adjustable via air pressure - Parallel electrode guidance - Single-stroke welding cylinder - Water-cooled via external water cooling system (recirculating water cooler not included) - Electric foot switch - Control cabinet with controller fixed to machine - Operating manual Required space (L x W x H): 1150 x 700 x 1600 mm Weight: 335 kg As-new condition

Condition: new, *IMMEDIATELY AVAILABLE* Includes: Hand winch Features: Net: €5,000.00 / Gross: €5,950.00 Article number: KET118331600.01 Technical data: • Brand: Stedele • Model: KET 18 • Vehicle type: Cable reel trailer • Vehicle condition: New • First registration: No first registration • TÜV/HU (technical inspection): 2 years from first registration • Internal dimensions (L x W x H): 330 x 163 x 0 cm • External dimensions (L x W x H): 325 x 220 x 171 cm • Loading height of the floor: 0 cm • Permissible total weight: 1,800 kg Guedpfx Akjzy Agke Usg • Unladen weight: 430 kg • Payload: 1,370 kg • Chassis: Low-loader (wheels beside the superstructure) • Tires: 185R14C • Suspension: ALKO rubber spring axle • Support wheel: Yes • 100km/h approval: Optional, can be retrofitted DESCRIPTION • Designed for cable reels up to a diameter of 1600 mm and a width of 1300 mm. • Standard tube holder approx. 60 mm • Torsion-resistant chassis with a solid receiving frame, hot-dip galvanized • Easy operation of the receiving frame with or without a cable reel • Barrier-free insertion of the cable reel • Play-free storage and securing of the reel by fixation • Solid support wheel holder and rear support • Stable telescopic crank supports at the rear • Incl. Robust and maintenance-free hand winch, pulling force approx. 2,300 kg • Very stable steel frame, welded • Frame completely hot-dip galvanized • Robust aluminum tread plate fenders, walkable • Reversing automatic system • ALKO overrunning device and parking brake • 13-pin plug • Reversing light • Large-sized safety lighting • Integrated rear fog light • Lighting recessed in the rear frame • Foldable license plate holder _____ Accessories can be retrofitted by our specialist workshop!! - Feel free to inquire about special requests! _____ - Financing or leasing possible - Nationwide delivery possible - All prices include VAT - Vehicle registration document can be sent in advance, or transfer license plates (Germany) can be provided. - Export license plates incl. customs registration possible Descriptions and images are protected by copyright!! Anhänger Zentrum BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers immediately available for you! We have been Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix - specialist dealer & repair - workshop for over 30 years. - Subject to errors, omissions and prior sale -

Condition: excellent (used), Water-cooled, manually operated DALEX spot welding tongs Type 3218 Rated power at 50% duty cycle: 16 kVA Secondary short-circuit current: 13.5 kA Electrode force: 270 daN with cardan suspension and mounting bracket 1 pair of electrode arms, 170 mm reach Godpfx Akjf Hi A Eo Ueug included: DALEX synchronous welding control unit RS 12 Power control via phase angle control Weld time 1-99, adjustable in synchronisation with connecting cable and 32 A CE plug and main switch

Condition: used, Year of construction: 2018, controller model: , _____ Description: Year of manuf. : 2018 Control : Technical data Year of manufacture:2018 Pressing force approx.:3200 kN Folding length approx.:4420 mm Control system:TASC 6000 Projection:420 mm Free upright clearance approx.:3680 mm Usable installation height approx.:615 mm Machine weight approx.:23400 kg Equipment :- Sturdy machine frame :- Press beam, stress relieved with high bending strength :- Spherical bearing of the press beam (inclined position) :- Electro-hydraulic top drive with 4-cylinder technology :- Optical set-up and positioning aid :- Generous edge clearance :- Flat front covers :- Block hydraulics :- Electronic pressure compensator :- Measuring system with glass scale and deflection compensation :- Hydraulic oil in the machine (lifetime lubrication) :- Oil cooler :- Control cabinet cooling via air-to-air heat exchanger :- Modern machine design Extended equipment :- 6-axis backgauge system :- Hydraulic upper tool clamping :- CNC crowning Gujdjyy Hgqepfx Ak Ujg :- Work area lighting front and rear BendMaster (150) :- Sturdy base body and manipulator in cast aluminium construction :- Load capacity 150 kg, plate plus gripper :- Low floor track in welded construction :- Sheet sensor for contour detection :- Rotary feed-through for easy gripper change :- Gripper coupling on BendMaster :- Sensors for 4-axis backgauge system :- Electric drives :- Double sheet detection :- Regripping station NC :- Vacuum generation for suction gripper :- Platform (300 mm) for the bending press Extended BendMaster equipment :Extended BendMaster equipment - Track extension to 12 m :- Sensor system for 6-axis back gauge :- Gripper changing console :- Vacuum gripper, undefined :- Modular vacuum gripper with separation (material for 3 grippers) :- Gripper coupling :- Tong gripper :- Sheet removal station with linear axis :- Side door on right for safety fence

Condition: used, Year of construction: 2005, machine/vehicle number: 55501133, This ABB spot welding cell is being auctioned off online in our industrial auction / machine auction follow-up auction, J&S GmbH Automotive Technology - Machine Park. Guedpfszyfz Rex Ak Uog You can find this and many other items on our platform.

Condition: new, Year of construction: 2025, Power at 50%: 20kVA Short circuit-current: 11,6kA Electrode force: 180daN Throat depth: 455mm --- Weld control: WS 402 (4-times, 2-program) --- Extra Equipment: Gusdpfx Aksk E Hnue Uog - foot pedal - main switch --- Warranty: 6 months --- Spotwelding electrodes + spare parts at stock

Condition: used, Year of construction: 1960, Technical details: current capacity: 60 kVA throat: 680 mm arm distance: 115 / 415 mm pincer opening adjustable: 180 mm rated capacity: 60 kVA welding power: 71 kVA electrode capacity: 100 bis 600 daN voltage: 380 V / 50 Hz V air pressure: min./max.: 6 / 10 bar cooling water consumption: 12 l/min weight of the machine approx.: 685 + 200 kg connection voltage: 380 V / 91 A V rated capacity: 60 kVA connected load: 54 kVA dimension L-W-H: ca. Maschine: 1.700 x 850 x 1.750 mm dimension L-W-H: ca. Aggregat: 900 x 650 x 1000 mm Guodpju Nv Emefx Ak Uog POINT WELDING MACHINE - WELDING TRANSFORMER Direct current three-phase welding machine Application: Spot, projection and series spot welding Maximum short-circuit power 89 kVA Primary short-circuit current 135 A Secondary current = short-circuit current: 25 kA and welding current max. 20 kA Electrode stroke max. 90 mm; electrode force min./max.: 100 daN / 600 daN Stroke sequence max. with 10 mm stroke 400 strokes/min. Spot fitting: electrode holder Ø 30 mm, adjustable 180 mm, arm distance = min./max.: 115 / 415 mm 2-fold foot switch Cooling unit, mobile = movable on wheels, connection power 1.45 kW, pipe connection R 3/4 inch, coolant R22 *

Year of construction: 2010, condition: like new (used), Used Trumpf Trubend Series 3000 CNC pressbrake for sale VIDEO BELOW: Used Trumpf Trubend 3120 for sale 3metre x 120ton 6 axis plus pressbrake for sale. Brand/make: TRUMPF Model: TRUBEND 3120 Type: CNC hydraulic Press Brakes New 2010 Location: United kingdom Low hours – 14,000 Specification Convert Specs to Imperial Tonnage 119.749 t / 120ton Type: hydraulic downstroke Overall Length 3.1 m /3metre BH 2.7 m Stroke 199.9 mm Number of axis: 7 axis 5 axis back gauge Weight 18298 (LBS) Control CNC (T3000) 132 Ton X 10′ Trumpf TruBend 3120 CNC Press Brake Year: 2010 Specification from new: Machine – Stable machine frame as welded all-steel construction – Ram, highly resistant to torsional forces – Spherical ram suspension, with ram tilt – Electro-hydraulic downstroking drive with 4-cylinder technology – Proportional valve technology – Modern block hydraulics – Electronic pressure balance – Measuring system with glass scale and frame deflection compensation – Hydraulic oil filled in the machine (lifetime lubrication) – Oil cooler Backgauge System – Backgauge system 2-axes with rack and pinion-drive for X- and R-axis, – 2 pieces back gauge fingers with safe adjustment in front of the machine Tool Holder – TRUMPF Upper tool clamping, manual and hardened – Lower tool clamping, manual and hardened Crowning – Self-regulating crowning system – Additional hydraulic CNC-crowning Control – Machine control: T3000 colour, DELEM based on Real Time for Windows – USB interfaces for keyboard, mouse, etc. Safety – Footswitch for Emergency up, down and emergency stop – Safety equipment: Side doors and manual shutter roller at the rear Services – Installation, start-up and instruction Options for Backgauge System – Back gauge system 5 axis Options for Tool Holder – Amada US Style fast clamping of upper tool holders (segmented, on entire working length) Options for Safety Device – BendGuard Options for Material Handling – Support bracket (2 pc) Delivery – June 2011 Video below: Used Trumpf V and C series cnc pressbrakes also available in stock for sale. We are always interested in buying used Trumpf pressbrakes and machines such as: TruBend 3066 TruBend 3100 TruBend 3170 TruBend Series 5000 TruBend 5085 Trubend 5130 TruBend Series 7000 TruBend 7050 TruBend 7036 TruBend 7050 TruBend Series 8000 Gusdpfx Akohtm Iks Usg TruBend 8230 Trubend 8400

Condition: good (used), Year of construction: 2007, functionality: fully functional, operating hours: 94,201 h, bending force (max.): 400 t, installation height: 595 mm, control type: CNC control, Bending length [mm] 3550 Pressing force [tons] 400 Control system Cybelec ModEva 10s Standard equipment: - Sturdy machine frame as a welded construction in all-steel design - Press beam with high bending strength - Electro-hydraulic upper drive via proportional valves - Modern block hydraulics - CNC rear stop for X and R axes, safe displacement of the stop fingers from the front by means of a safety interlock - Upper tool clamping system "EHT", manual, head width 26mm, load max. 3000 kN/m - Lower tool clamping system EHT, manual, clamping width 90mm for block tools and 13mm for single V-dies, without clamping - Control system: CYBELEC ModEva 10S on Windows, 2D graphic control with a 10.4" color screen - Control cabinet air conditioning + Rear stop - System 1, 5 axes, straight finger, 140mm wide, adjustment of R axis 150mm + EHT quick clamping device, for upper tools, pneumatic, head width 26mm, load max. 3000 kN/m (self-centering horizontally) + EHT lower tool clamping, pneumatic, clamping width 55mm + Hardened insert strip, for EHT lower tool clamping 55mm / 90mm + Lower tool displacement, CNC-controlled, infinitely adjustable via rear stop 1 (max. 4550 mm working length) + Crowning device CNC-controlled, in the table without tool clamping, load max. 3000 kN/m + Safety device LaserSafe (up to max. upper tool height 440mm) + Additional foot switch + Bending aid 1st arm, load max. 1500N with 2 integrated support strips in standard design + Bending aid 2nd arm, load max. 1500N with 2 integrated support strips in standard design + 2 pcs. support strips for a bending aid with T-slot 14mm and scale and ball rollers + 2 pcs. table extension for bending aid Godpfx Akoy Saurs Usug + Short park position left + Short park position right

Condition: excellent (used), Power source 250 Amp (60% duty cycle) WELDKAR WK MIG 250 DUAL PULS, suitable for industrial use. In continuous use, the maximum welding current is 195 A. The MIG 250 Dual Pulse welding machine is versatile and is suitable for MIG / MAG, TIG (lifting arc) and MMA (electrode) welding. Equipped with various synergic welding programs for steel, stainless steel, aluminum and CuSi3. In addition, this welder is equipped with the Pulse and double pulse function. Up to 100 welding programs can be saved and recalled. Parameters can also be manually adjusted by the welder if required. Gjdpjd Nzlxjfx Ak Ujug The power source is equipped with a digital control panel where various parameters can be easily set and read. Including gas flow, soft start, combustion, downward slope, gas flow and pulse rate control. The latter is necessary for thin-walled welding. The 2 - 4 stroke setting provides extra convenience when welding longer parts. Partly due to the 4-roller wire feed system, a long and trouble-free wire feed is guaranteed. With the MMA function, coated electrodes can be welded. To further optimize the weld, hot start arc force parameters can be set. The welder is portable and available in a mobile frame. Furthermore, they are CE and EMC certified and suitable for use with generators with a minimum power of 12.5 kVA. WELDING MACHINES ARE COMPLETELY NEW, POST-EXHIBITION.

Condition: new, *IMMEDIATELY AVAILABLE* Includes: Hydraulically Lowerable, Cover Equipment: - Manual hand pump - V-drawbar - 10x lashing eyes Net: €8,382.35 / Gross: €9,975.00 Article number: FBA227401921.11 Technical data: • Brand: Vezeko • Model: Husky Car FB 27.39 • Vehicle type: Lowering trailer • Vehicle condition: New vehicle • First registration: without first registration • TÜV/MOT: 2 years from first registration • Internal dimensions (LxWxH): 394 x 187 x 210 cm • External dimensions (LxWxH): 553 x 254 x 264 cm • Loading height of the floor: 44 cm • Permissible total weight: 2,700 kg • Unladen weight: 705 kg • Payload: 1,995 kg • Chassis: Low loader (wheels next to the body) • Tires: 195/50R13C • Suspension: ALKO rubber spring axle • Support wheel: Yes • 100km/h approval: Optional, can be retrofitted Gjdpfezy At Rox Ak Uoug DESCRIPTION • 15mm multiplex floor panel, made of birch wood, with anti-slip coating - extremely robust • Side panels made of anodized, double-walled aluminum profile 10cm • Insertion options at all corners for e.g. tarpaulin frame • Cover incl. spar frame. Internal height: 210cm, color: black • Very stable steel frame welded • Frame completely hot-dip galvanized • Many stable cross members, resulting in high point load capacity • Loading area hydraulically lowerable, license plate holder at the rear, can be swiveled away for loading • Mechanical safety lock of the pivoting axle during operation • With over-run protection at the rear • Additional longitudinal struts continuously welded in • Tool box at the front • 10 lashing eyes within the V-loading rail, rubber-coated, tensile force (750DaN/kg) • ALKO overrun device and parking brake • Coupling head ALKO • Very stable V-drawbar REINFORCED • Reverse automatic • 13-pin connector • Reversing light • Large-sized safety lighting • Integrated rear fog light • Rear position lights in LED • Lighting recessed in the rear frame • Support wheel with clamping bracket in the middle _____ Accessories can be retrofitted by our specialist workshop!! - Please feel free to request any specific requirements! _____ - Financing or leasing possible - Delivery nationwide possible - All prices include VAT - Vehicle registration document can be sent in advance or transfer license plates (Germany) can be provided. - Export license plates including customs registration possible Descriptions and images are protected by copyright!! Anhänger Zentrum BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers immediately available for you! We have been Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix - specialist dealer & repair - workshop for over 30 years. - Errors, omissions and prior sale are subject to change -

Condition: new, *IMMEDIATELY AVAILABLE* Includes: Manual winch Equipment: Net: €6,378.15 / Gross: €7,590.00 Article number: KTT227331600.01 Technical data: • Brand: Stedele • Model: KTT 27 • Vehicle type: Cable reel trailer • Vehicle condition: New • First registration: No first registration • TÜV/HU (technical inspection): 2 years from first registration • Internal dimensions (LxWxH): 330 x 163 x 0 cm • External dimensions (LxWxH): 499 x 247 x 265 cm • Loading height of the floor: 0 cm • Permissible total weight: 2,700 kg • Tare weight: 760 kg • Payload: 1,940 kg • Chassis: Low loader (wheels next to the superstructure) • Tires: 185R14C • Suspension: ALKO rubber spring axle • Support wheel: Yes • 100 km/h approval: Optional, can be retrofitted DESCRIPTION • Designed for cable reels with a diameter of up to 2800 mm and a width of 1650 mm. • Standard tube holder approx. 80 mm • Torsionally rigid chassis with a massive receiving frame, hot-dip galvanized • Easy operation of the receiving frame with or without a cable reel • Barrier-free insertion of the cable reel • Play-free storage and securing of the reel by fixing • Massive support wheel holder and rear support • Stable telescopic crank supports at the rear • Includes robust and maintenance-free manual winch, pulling force approx. 2,300 kg • Very stable steel frame, welded • Frame completely hot-dip galvanized • Robust aluminum checker plate fenders, walkable • Reversing automatic • ALKO overrun device and parking brake • 13-pole plug • Reversing light • Large-sized safety lighting • Integrated rear fog light • Lighting recessed in the rear frame • Foldable license plate holder Gusdpfx Akozy Dvtj Usg _____ Accessories can be retrofitted by our specialist workshop!! - Please feel free to request any special features! _____ - Financing or leasing possible - Delivery throughout Germany possible - All prices include VAT - Vehicle registration document can be sent in advance, or transfer plates (Germany) can be provided. - Export license plates incl. customs registration possible Descriptions and images are protected by copyright!! Anhänger Zentrum BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers immediately available for you! We have been Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix - specialist dealer & repair - workshop for over 30 years. - Errors, omissions and prior sale excepted -