Used Weinig Unimat 23 El for sale (473)

Condition: reconditioned (used), Year of construction: 1985, functionality: fully functional, For sale is a used four-sided planer/moulder from Weinig with 7 spindles and powered infeed roller conveyor. The machine has been in operation since at least 1985 and was overhauled in the workshop in 2007. It is in working condition but is no longer in use. The exact year of manufacture is unknown; based on its design and equipment, it is likely a Weinig Unimat 17 series machine from the 1980s. Technical data (approximate values): - 7 spindles - Spindle diameter: 40 mm - Working width: approx. 20 – 170 mm Dcsdpfx Acew Rkqgj Nsc - Working height: approx. 8 – 120 mm - Tool diameter: up to approx. 160 mm - Feed speed: 6 – 24 m/min - Voltage: 380 V / 50 Hz - Weight: approx. 4,500 kg - Including powered infeed roller conveyor - Including various cutters (see photo) Note: This is a used, older model machine, being sold without warranty. Inspection by appointment possible.

Condition: excellent (used), WEINIG Hydromat H23 Line, S/N 87321, year 1999, Ref-No. 103437 WEINIG Cross Conveyor HighMech E-1, equipped with 6 flat chains approx. 2000 x 3500 mm Hydraulic WEINIG Accelerator Model 814 Short infeed table with heavy-duty 4-roller feed unit Planer/moulder with reinforced KASCHWIG three-sided soundproof enclosure • Max. working width: 230 mm • Max. working height: 160 mm • Electronic feed, frequency-controlled, 8–80 m/min • Feed motor 18.5 kW • 1st spindle bottom 11.0 kW • 2nd spindle right 11.0 kW • 3rd spindle left 11.0 kW Dedpewvqklofx Ac Nscc • 4th spindle right 11.0 kW • 5th spindle left 11.0 kW • 6th spindle top 15.0 kW • 7th spindle bottom 11.0 kW • 8th spindle top 15.0 kW • 9th spindle bottom 15.0 kW • 10th universal spindle 11.0 kW (four-sided) • Spindle speed 6,000 rpm • Spindle diameter ø 50 mm • All spindle motors equipped with NEW motor start/stop brake units • Pneumatically supported top pressure rollers • Feed rollers D=140 mm • 6 driven rollers in the table • Spindles 1 + 6 + 7 + 8 + 9 with counter bearings • Spindles 8 + 9 with straight jointer • Spindles 8 + 9 with profile jointer • Spindles 6 + 8 with pneumatic pressure • Reduced spacing between feed rollers • Hard-chromed table plates • Hard-chromed fences • Pneumatically supported side pressure rollers • Automatic table lubrication • Centralized lubrication points • Free-standing control panel • Connected load approx. 145 kW / approx. 400 A • Free-standing electrical cabinet • Operating instructions, spare parts list and wiring diagram included • Machine sold without cutterheads Machine dimensions approx.: • Length: 6,000 mm • Width: 2,250 mm • Height: 1,800 mm • Weight: approx. 8,500 kg Factory-new WEINIG components installed: NEW horizontal/vertical spindle NEW counter bearings All spindles with HL bearings All motors newly fitted NEW electronic motor soft start/brake devices NEW hard-chromed table plates NEW hard-chromed fences Many other new parts fitted in the machine Condition: see attached photos – technically in excellent condition Infeed mechanization unrefurbished – complete – fully functional Payment: Net cash before loading Delivery time: By arrangement Delivery: EXW Inspection: Anytime by appointment Errors and prior sale excepted.

Condition: refurbished (used), Weinig brand moulder, mod. 22A Unimatic Workbench width: 220 mm, with ribbed table for short pieces. Cardan shaft towing. Dcsdpju Sr Ddsfx Ac Nec Engine composition and power: Lower 5.5 kW Right 5.5 kw Automatic left 5.5 kw (moving shaft) Right 5.5 kw Superior 5.5 kw Lower 5.5 kW 4kW towing motor Automatic left shaft hydraulic power unit 0.9 kW The left movable shaft moves automatically according to the width of the inserted workpiece.

Year of construction: 1987, condition: excellent (used), working width 170 mm planing height 120 mm table surface length 1950 mm 5 spindles: 1. lower 2. right 3. left 4th top Dcjdpfx Acolx Em Uj Noc 5. universal feed speed 6.5 - 49 m/min. cardan feed electrically lifted pressure beam

Condition: used, Working width: 230 mm Working height: 120 mm Spindles: 5 Spindle 1: Bottom / 5.5 kW / 40 mm Dcjdpfx Acex Ecgue Nsc Spindle 2: Right / 5.5 kW / 40 mm Spindle 3: Left / common motor with #2 / 40 mm Spindle 4: Top / 7.5 kW / 40 mm Spindle 5: Bottom / 4 kW / 40 mm Weinig Profimat 23 E four-sided planer and moulder for planing and profiling timber on all four sides, equipped with mobile spindle.

Condition: ready for operation (used), Year of construction: 2008, functionality: fully functional, The machine is currently in use. We offer live demonstration, dismantling loading, installation and training on your site Dcedpfov Uab Eox Ac Nsc

Condition: excellent (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: 92552, working width: 230 mm, planing height: 120 mm, working height: 120 mm, spindle diameter: 40 mm, power of feed motor: 1,500 W, 🪚 2001 Weinig Quattromat 23P Planer Moulder – Industrial Performance in Very Good Condition Now available for sale: a 2001 Weinig Quattromat 23P, one of the industry’s most reliable and compact 4-sided planing and moulding machines, ideal for workshops producing mouldings, profiles, cladding, architraves, and more. This unit is in very good condition, fully operational, and perfect for businesses looking to increase productivity with a trusted European-built planer moulder. ✅ Key Features – Weinig Quattromat 23P Year of Manufacture: 2001 Condition: Very Good – well-maintained, and ready to run Working Width: 13 to 230 mm Working Height: 6 to 120 mm Number of Spindles: 4 Spindle Diameter: 40 mm Spindle Speed: 6,000 rpm Feed Speed: Variable up to 20 m/min Power: Approx. 21 kW combined spindle power Infeed Table: 1,800 mm Pneumatic Pressure System: For consistent timber hold-down Digital Readouts: For quick and accurate spindle positioning Straightening spindle motor: 4 - 7.5 KW (5.5 - 10 HP) Vertical spindles motor: 5.5 - 11 KW (7.5 - 15 HP) Top spindle motor: 4 - 11 KW (5.5 - 15 HP) Feed motor: 1.5 KW (2 HP) Spindle speed: 6,000 rpm Spindle diameter: 40 mm Tool cutting circles of moulding spindles: 125 - 200 mm Adjustment range of spindles (axial): 30 mm Adjustment range of straightening spindle: 5 mm Feed speed: 8 m/min. Feed roller diameter: 140 mm Feed roller width: 2 x 50 mm Width of roller in the outfeed table: 50 mm Adjustment range of straightening table and edge-jointing fence: 10 mm Height of right fences: 60 mm Length of straightening table: 2 m Reference engraver with cutter: Yes Pneumatic pressure for feed rollers: Yes Pneumatic adjustment of infeed roller in front of 1st bottom spindle: Yes Pressure roller from above and left in front of machine infeed: Yes 🛠️ Machine Capabilities 4-sided planing for smooth and dimensionally accurate timber Profile moulding (e.g. tongue & groove, chamfering, rebating, etc.) Batch production of window, door, or cladding components Compact footprint – ideal for smaller workshops or mobile production lines Easy spindle access and minimal setup time 📦 Included with Machine Weinig Quattromat 23P base unit Dust extraction ports Original manuals and operator instructions Fully tested, serviced, and ready for production 🪵 Perfect For: Joinery workshops Timber frame manufacturers Djdswnr Enopfx Ac Nocc Furniture makers Shed and fencing producers Custom millwork and architectural moulding shops 📍 Availability & Delivery The machine is in stock now and available for immediate inspection and dispatch. We offer delivery across Ireland, UK and Europe. 📞 Contact Us Today Boost your timber processing capabilities with this robust and accurate Weinig Quattromat 23P. Weinig Quattromat 23P for sale Used Weinig planer moulder in very good condition 4-side planer moulder woodworking machine Industrial wood planer for moulding production Compact planer moulder for small workshops Weinig planing and profiling machine UK / Ireland / Europe Second-hand Weinig machinery for woodworking

Condition: excellent (used), Year of construction: 2003, Weinig Hydromat 23C with 6 Spindles. Separate electrical panel. Automatic lubrication system for bedplates Maximum dimensions 140mm x 230mm No 1.  11kw - Bottom 6000rpm + Outboard bearing - straight jointer prepared No 2. 11kw - Right 6000rpm - straight and profile jointer prepared No 3. 11kw - Left 6000rpm - straight and profile jointer prepared No 4 . 15kw - Top 6000rpm + Outboard bearing - jointer prepared No 5 . 11kw - Top 6000rpm + Outboard bearing - straight jointer No 6 . 18.5kw - Bottom 6000rpm + Outboard bearing - straight jointer 7.5 kw feed. 6-60m/min (Possible to increase speed as needed). 50mm spindles Beam 0.55kW Full documentation included. Possible to supply with hydro tooling if needed. Possible to supply with infeed and outfeed if needed. Dcjdpfx Aoycvd Aoc Njc

Condition: excellent (used), Year of construction: 1995, Weinig Profimat 23E four side planer - German production - year of production 1995 - right and left spindles with a face milling cutter ensuring parallelism and a right angle of 900 - element width measurement - electronic width adjustment TECHNICAL PARAMETERS: planing width 230 mm planing height 120 mm electronic planing width control 1 lower spindle 4 kW 2 right spindle 4 kW 3 left spindle 4.2 kW (face milling) 4 spindle right 4.2 kW (face milling) 5 upper spindle 7.5 kW element width measurement electric height adjustment of the feed rollers electric height adjustment of the upper spindle spindle diameter 40 mm Dcedpfxeibq Nis Ac Nec six top steel rollers yen top roller, rubber one roll in the table top pulling pneumatic pressure feed on cardan shafts pre-table length 2470 mm diameter of nozzles 140 mm Machine dimensions 456x240x220 weight 4000 kg

Condition: good (used), Year of construction: 1979, functionality: fully functional, Four-sided planer / moulder Unimat 22N, 7 spindles Year of manufacture 1979 S/N 286512746 Dcsdpfst Eu Htsx Ac Njc Manufacturer Weinig Germany planing width 220mm Planing height 120 mm 7 planer shanks: planing table length 2000mm Spindle arrangement (speed of the working spindles 6000 rpm) 1. bottom, 4 kW 2. left, 5,5kW 3. right, 7.5 kW 4. left, 4 kW 5. top, 7.5 kW 6. bottom, 7.5 kW 7. bottom, 4.0 kW 5, 6, 7 with counter bearing 3 rollers in the table (not driven) spindle diameter 40 mm Flying circle of the dressing spindle 125mm Flying circle of the dressing spindle 100-180mm Largest flying circle of the milling spindles 180mm Cardanic feed Feed infinitely variable (frequency converter) 6-36 m /min. Manual Waxilit pump External dimensions L 4500 mm x W 1600 mm x 1700mm 4500 kg with 7 planer/knife heads included

Condition: good (used), Year of construction: 2010, WEINIG NKT Finger Joint Cutter Double-Pack DP20 Dedpsx Ti Rfefx Ac Necc An industrial finger jointing line – engineered for maximum precision and efficiency Technical Specifications: Wood infeed length: min. 130 mm | max. 1000 mm Wood outfeed length: min. 3700 mm | max. 7400 mm Wood cross-section: min. 20 x 40 mm | max. 80 x 180 mm Cutter diameter: 370 mm Finger joint type: Vertical / Horizontal, 10/11 fingers, 3.8 mm pitch Glue application: 2-sided, PVAC white glue Connected load: 80 kW Note: The machine is currently dismantled and stored at our site. Inspection is possible by appointment. Scope of delivery: WEINIG NKT Double-Pack DP20 incl. control unit Integrated glue station for two-sided application Operating manual & documentation

Condition: good (used), Year of construction: 1983, functionality: fully functional, Four-sided planer / moulder Unimat 22A, 7 spindles Year of manufacture 1983 S/N 225-347 Manufacturer Weinig Germany Planing width 220mm Plane height 120 mm 7 planing shafts: Jointer table length 2000 mm Spindle arrangement (speed of the working spindles 6000 rpm) 1. bottom, 4 kW 2. right, 3 kW 3. left, 4 kW 4. right, 4 kW 5. top, 7.5 kW 6. bottom, 4 kW 7. universal, 11 kW Dsdperb D Dlsfx Ac Njcc Powered smooth pull-out roller in the table spindle diameter 40 mm Flying circle of the dressing spindle 125 mm Flying circle of the dressing spindle 100-180mm Largest flying circle of the milling spindles 180mm Cardanic feed Feed infinitely variable (frequency converter) 6-36 m /min. Manual Waxilit pump Outer dimensions L 4000 mm x W 1600 mm x 1700mm 4500 kg

Condition: excellent (used), functionality: fully functional, Working width: 230 mm Working height: 160 mm Number of spindles: 5 Spindle configuration: 1. Bottom 15 kW 2. Right 11 kW 3. Left 11 kW 4. Top 15 kW 5. Bottom 7.5 kW Spindle speed: 6000 rpm Spindle diameter: 50 mm 3 feed rollers in the work table Feed speed adjustable via inverter up to 60 m/min Dedpjx Hzv Tefx Ac Nocc Feed driven by cardan shaft Pneumatic pressure rollers Technical documentation Machine dimensions: 300x180x170 cm (H) Weight: 3500 kg

Condition: excellent (used), Weinig Hydromat 23C with 6 Spindles. Max width 245mm Max Thickness 160mm Separate electrical panel. Separate remote control panel Automatic lubrication system for bedplates Full heavy duty sound enclosure. 15kW feed motor 100m/min No 1.  7.5kw - Bottom 6000rpm straight jointer prepared No 2. 11kw - Right 6000rpm straight and profile jointer prepared No 3. 15kw - Left 6000rpm straight and profile jointer prepared No 4 . 15kw - Top 6000rpm + Outboard bearing + straight and profile jointer prepared Dcodpfx Ajx N T Imoc Njc No 5 . 30kw - Top 6000rpm + Outboard bearing + straight and profile jointer prepared No 6 . 15kw - Bottom 6000rpm + Outboard bearing + straight and profile jointer prepared 50mm spindles Beam 0.55kW Full documentation included. Heavy duty sound enclosure. Possible to supply with hydro tooling if needed. Possible to supply with full mechanisation if needed.

Condition: used, Year of construction: 1997, diameter - cutter special 30 mm draw-in arbor diameter 40 mm clamping height 310 mm circle diameter 80-300 mm weight 30 kg Dcsdpfov Uchbsx Ac Nsc

Condition: used, Year of construction: 1995, 5-station molder Capacity 240 mm/125 mm Digital positioning ATS System ALU tool holders Dcsdpfjx A Dz Usx Ac Njc Table lubrication 380 V

Condition: excellent (used), Four-side planer Weinig Hydromat 23C Working width: 230 mm Working height: 160 mm Number of spindles: 7 Spindle arrangement: 1. Bottom 15 kW 2. Right 7.5 kW 3. Left 7.5 kW 4. Top 15 kW 5. Bottom 30 kW (multi-blade saw) 6. Bottom 7.5 kW (hydro support) 7. Top 7.5 kW (hydro support) Spindle speed: 6000 rpm Spindle diameter: 50 mm 4 feed rollers in the worktable Feed speed adjustable via frequency inverter up to 36 m/min Feed drive powered by cardan shaft Pneumatic pressure elements Dcodpfsxlcufex Ac Noc Technical documentation

Condition: used, Adjustment status for Weinig Powerlock Dodpfx Ajxga Ewsc Nscc

Condition: excellent (used), Weinig Hydromat 23C with 6 Spindles. Max width 245mm Max Thickness 160mm Separate electrical panel. Separate remote control panel Automatic lubrication system for bedplates Dsdpsx Dq Rfsfx Ac Nscc Full heavy duty sound enclosure. 15kW feed motor 100m/min No 1.  7.5kw - Bottom 6000rpm straight jointer prepared No 2. 11kw - Right 6000rpm straight and profile jointer prepared No 3. 15kw - Left 6000rpm straight and profile jointer prepared No 4 . 15kw - Top 6000rpm + Outboard bearing + straight and profile jointer prepared No 5 . 30kw - Top 6000rpm + Outboard bearing + straight and profile jointer prepared No 6 . 15kw - Bottom 6000rpm + Outboard bearing + straight and profile jointer prepared 50mm spindles Beam 0.55kW Full documentation included. Heavy duty sound enclosure. Possible to supply with hydro tooling if needed. Possible to supply with full mechanisation if needed.

Condition: used, Profile spindles WEINIG 1 piece length 1100 mm 1 piece length 650 mm Dcedpfx Asq Tn Tuoc Njc 2 pcs length 700 mm 2 pcs length 900 mm

Condition: used, Adjustment status for Weinig Powerlock profile Dcjdpfxjxga Eqs Ac Njc

Condition: good (used), Year of construction: 2006, I sell the automatic pneumatic end cutting saw Weinig Grecon Dimter Opticut 200 Elite Year 2006 Motor power 7,5kW Input table automatic feeding 4,10m (throughfeed system) Dodpoxtxi Ijfx Ac Nocc Outut table automatic 6 pcs. kickers on right outfeed table Optimising with mistakes deffect reading and automatic cutting sequence modes. Available immediately. CE version. Documentation included.

Condition: good (used), Year of construction: 2005, I sell the automatic pneumatic end cutting saw Weinig Grecon Dimter Opticut 200 Elite Year 2005 Motor power 7,5kW Input table automatic feeding 5,10m (throughfeed system) Dcjdpfextxg Hox Ac Noc Outut table automatic 6 pcs. kickers on left outfeed table Optimising with mistakes deffect reading and automatic cutting sequence modes. Available immediately. CE version. Documentation included.

Condition: used, Tenoning spindle 1 St. Number of milling agregates 5 St. Spindle diameter 50 mm Control Weinig, PC-Nexus # 2774 Weinig Unicontrol 6 with NC spindles Machine will be cleaned and completely checked before delivery ----- Technical data summary Dedpfxevu Hghe Ac Necc (please enquire about any additional accessories included) Item 1: Cross-cut saw ----- > Number of tools: 1 pc. > Spindle speed: 2,800 rpm > Spindle diameter: 40 mm > Max. tool diameter: 400 mm > Motor power: 3 kW > Radial adjustment path pneumatically controlled to 8 positions, e.g. for edge rounding from above > Laser aiming light for detecting the saw section Item 2: Rounding unit horizontal below ----- > Position: horizontal below > Motor power: 1.5 kW > Spindle diameter: 20 mm > Clamping length 25 mm > Spindle speed: 9,000 rpm > Max. tool flight circle: 130 mm > Axial adjustment path mechanically coupled with Crosscut saw > Adjustment path radial pneumatically controlled on/off Length stop NC controlled ----- > Length 3500 mm > Electronic length stop Item 3: Tenon and slot spindle ----- > Number of tools: variable, stepless adjustment, NC > Tool clamping length: 320 mm > Vertical spindle stroke: variable 254 mm, stepless adjustment, NC-controlled > Spindle speed: 3500 rpm > Tool flight circle max. 320 mm > Spindle diameter: 50 mm > Tool diameter max.: 320 mm > Motor power: 11 kW Item 4: 1. Profiling spindle (same and opposite rotation) ----- > Position: vertical right > Number of tools: 1 pc. > Tool clamping length: 120 mm > Spindle speed: 6000 rpm > Spindle diameter: 50 mm > Tool flight circle max.: 232 mm > Motor power: 7.5 kW Item 5: 2nd profiling spindle ----- > Position: vertical right > Number of tools: variable, stepless adjustment, NC > Tool clamping length: 320 mm > Vertical spindle stroke: variable 254 mm, stepless adjustment, NC-controlled > Spindle speed: 6000 rpm > Spindle diameter: 50 mm > Tool flight circle max.: 232 mm > Motor power: 11 kW 2 feed rollers axially pneumatic opposite the spindle controlled, 2 positions Rung guide consisting of: Guide ruler in the stop (area of ??the synchronous spindle), Rung support bar from above in the area of ??the profile milling unit vertically on the right and profiling spindle. Pos. 6: Profile milling unit horizontal top ----- > Clamping length: 40 mm > Spindle diameter: 40 mm > Motor power: 3.0 kW > Speed ??9,000 rpm > Tool flight circle max. 130 mm > Axial adjustment range 30 mm, 8 positions > Radial adjustment range 125 mm, 8 positions Pos. 7: 3rd profiling spindle (fitting spindle) ----- > Position: vertical right > Tool clamping length: 160 mm > Axial adjustment range 115 mm, 8 positions > Radial adjustment range 110 mm, 8-way turret > Spindle speed: 5850 rpm > Spindle diameter: 40 mm > Tool flight circle max.: 210 mm > Motor power: 3.0 kW Item 8: Profile milling unit/grooving unit from below ----- > Motor power: 3.0 kW > Tool clamping length: 125 mm > Axial adjustment range 100 mm, 8 positions > Radial adjustment range 1...

Condition: used, Tenoning spindle 1 St. Number of milling agregates 4 St. Spindle diameter 50 mm control Weinig, PC-Nexus # 2764 Weinig Unicontrol 6 with NC spindles ----- Machine will be cleaned and completely checked before delivery Technical data summary (please enquire about any additional accessories included) Item 1: Cross-cut saw ----- > Electronic cross-cut saw, infinitely adjustable horizontally > Number of tools: 1 piece > Spindle speed: 2,800 rpm > Spindle diameter: 40 mm > Max. tool diameter: 400 mm > Motor power: 3.0 kW > Laser aiming light for detecting the saw section > NC length stop, mounted on slot table included Positioning of the cross-cut saw integrated in the control system. > Length 3500 mm Item 2: tenoning spindle ----- > Number of tools: variable, infinitely variable adjustment NC axis Dsdpfxevu Hfqj Ac Nscc > Tool clamping length: 320 mm > Vertical spindle stroke: variable, infinitely variable adjustment 254 mm NC axis > Spindle speed: 3500 rpm > Spindle diameter: 50 mm > Max. tool diameter: 320 mm > Motor power: 11 kW Item 3: 1st profiling spindle (synchronous spindle and counter-rotation) > Position: vertical right > Number of tools: 1 pc. > Tool clamping length: 120 mm > Spindle speed: 6000 rpm > Spindle diameter: 50 mm > Max. tool flight circle: 232 mm > Motor power: 7.5 kW Item 4: 2nd profiling spindle ----- > Position: vertical right > Number of tools: variable, infinitely variable adjustment NC axis > Tool clamping length: 320 mm > Vertical spindle stroke: variable, infinitely variable adjustment 254 mm NC axis > Spindle speed: 6000 rpm > Spindle diameter: 50 mm > Tool flight circle max.: 232 mm > Motor power: 11 kW 2 feed rollers opposite the spindle, axially pneumatically controlled, 2 positions Rung guide consisting of: Guide ruler in the stop (area of ??synchronous spindle), Rung support bar from above in the area of ??profile milling unit vertical right and profiling spindle. Pos. 5: Profile milling unit horizontal top ----- > Clamping length: 40 mm > Spindle diameter: 40 mm > Motor power: 3.0 kW > Speed ??5,850 rpm > Tool flight circle max. 130 mm > Axial adjustment range 30 mm, 8 positions using pneumatic turret > Radial adjustment range 125 mm, 8 positions using pneumatic turret Pos. 6: 3rd profiling spindle (fitting spindle) ----- > Position: vertical right > Tool clamping length: 160 mm > Axial adjustment range 115 mm, 8 positions using pneumatic turret > Radial adjustment range 100 mm, 8 positions using pneumatic turret > Spindle speed: 5,850 rpm > Spindle diameter: 40 mm > Max. tool flight circle: 210 mm > Motor power: 3.0 kW Other features ----- > online-capable > rebating device for tear-free rebating > double parts package > return conveyor for 1-man operation: tilting belt > screen control > inclined window device > electronic angle display for inclined windows > industrial PC, PC control/NEXUS > Weinig type production program > without processing tools No original images available yet. Images show identical machines from our archive. ----- Price of the above-mentioned machine upon request! ----- Optional with additional charge: EUR 6.500,00 Note on used tools: We currently ha...