Used Weinig Powermat for sale (543)

Condition: as good as new (ex-display), Please check in your junk mail if you do not receive a reply within 24hrs from sending your inquiry !!! CAN SHARPEN MAX 406MM DIAMETER CUTTERS !!! The G-716 Semi-automatic Cutterhead Grinder is used to sharpen 178mm to 406mm diameter eased edge, milled to pattern, and fingerjoint cutterheads. Worktable traversing is automatic and has adjustable stops. Cutterhead indexing is manual. Each knife is held against a positive stop while being ground !!! No Index Plate To Change No index plate to change when working with heads with different numbers of knives. The use of an index plate assumes that the knives and head separations are uniform throughout, which is often not the case. If the height of the knife is high or low, then the front face of the knife will vary from knife to knife making the task of grinding difficult. The one constant is the back face of the knife, therefore the use of an indexing stop against the back face will provide for accurate indexing regardless of the irregularities in the knives and head slots. Head Indexing and Wheel Feed: Manual Minimum / Maximum Diameter Cutterhead: 7″ Min./16″Max. 178mm Min./ 406mm Max. Worktable Feed: Air / Oil Travel (maximum): 12″ 305mm. Adjustable Limits: Proximity Switch Speed: Fully Adjustable Index Method: Hedpfjq Dzi Tsx Acnot Manual index after each knife is ground. Grinding Spindle: 1-1/2 HP Wash Down Duty TEFC Motor 3600 RPM, Dual ABEC 7 Precision Bearings, with Sealed Lubrication. 8″ (203mm)Diameter Grinding Wheel (9″ 229mm Diameter Max.) Coolant System: 15 Gallon Tank with Casters, Sediment Tray Full View Sight Glass, 5 GPM Pump (120VAC) Wash Down Hose Included Specifications Grinds 7″ to 16″ diameter eased edge, milled to pattern, and finger joint heads Automatic traversing worktable with adjustable travel limits Manual indexing of knives against a positive stop with grinding position pneumatic brake allowing precision indexing without the need of an index plate High precision 1-1/2 HP grinding spindle with sealed lubrication Recirculating adjustable flow flooded coolant system with wash down hose Fully enclosed grinding chamber with viewing windows and task light Grinding wheel feed allows unattended operation. New Proscale.

Year of construction: 2000, condition: excellent (used), Weinig High-Mech A4 bundling system Bundle forming packaging unit possible to combine with other Weinig outfeed handling systems available from stock such as buffers and stackers. Hsdoq Rvrbspfx Acnot Consisting of 1. Weinig 815-300 high speed bundling unit 2. Weinig 812-200 outfeed roller conveyor with crossfeed 3. Control panel with Siemens S7-300 CPU

Condition: like new (used), functionality: fully functional, planing height: 190 mm, spindle diameter: 50 mm, planing width: 250 mm, overall weight: 10,000 kg, Weinig Hydromat H25N four-sided planer with 100 m/min feeder - German production - hydraulic feed up to 100 m/min - for wet wood - serving table TECHNICAL PARAMETERS: planing width 250 mm planing height 190 mm spindle diameter 50 mm electric height adjustment 1 lower spindle 15 kW 2 right spindle 7.5 kW 3 left spindle 15 kW 4 right spindle 7.5 kW 5 upper spindle 7.5 kW 6 upper spindle 15 kW 7 lower spindle 7.5 kW 8 universal spindle 1800 7.5 kW feed smoothly adjustable up to 100 m/min feed pump motor power 22 kW nine rollers in the table top, three of which are in front of the first head seven upper steel pulling rollers four upper rubber pulling rollers pneumatic pressure jointer on 1-6-7 spindle automatic lubrication of the countertop feeding table 3000 mm speed smoothly adjustable up to 100 m/min two upper pneumatic rollers Hodpsn Slk Usfx Acnet six lower pulling rollers minimum material length 650 mm Transport dimensions 11000x2400x2000 mm weight 9 tons

Condition: good (used), Year of construction: 2010, RAIMANN Econorip 310 multi-saw - German production - CE marking - Quickfix disc sliding system - year of production 2010 TECHNICAL PARAMETERS: - cutting height 110 mm - cutting width 340 mm - engine power 22 kW - adjustable feed on the inverter - electric shaft height adjustment Hedoh Tm Alepfx Acnot - electric adjustment of the pressure height - spindle in the Quickfix system (the possibility of changing the dimensions without the need for tools) - track diameter max 350 mm - spindle diameter 65 mm - sleeve diameter 80 mm - four upper pressure rollers - four rows of anti-jet pawls - boot for short elements - max width of the element 700mm - minimum element length 300 mm - central lubrication - diameter of the stub pipe 250 mm - ruler Machine dimensions: 190x185x165 cm weight 1800 kg

Condition: excellent (used), Raimann KS 310 BV edger multisaw Hedpfx Aeir Eubocnot - year of manufacture 1995 - German production - DTR - two movable discs TECHNICAL PARAMETERS: - track width 340 mm - cutting height max 120 mm - engine power 30 kW - disc diameters 250/360 mm - Possibility to put on a shoe - electric height adjustment - feed continuously adjustable 11-38 m / min - power of the feed motor 1.5 kW - two movable discs - three lasers - max element width 1000 mm - minimum element length 600 mm with a shoe 400 mm - four upper pressure rollers - spindle diameter 65 mm - sleeve diameter 80 mm - spigot diameter 250 mm Dimensions 230x220x230 weight 2500 kg

Condition: excellent (used), Year of construction: 2005, Weinig Dimter OptiCut S 90 optimizer with 2 ejectors – after technical review – German production – year of manufacture 2005 TECHNICAL PARAMETERS: max. length of cut material 4500 mm max. width 360mm Hedpoi Apgmofx Acnot max. height 160mm automatic length measurement optimization in 4 quality classes total power 13 kW blade motor power 7. 5 kW pneumatic side and top pressure disc diameter max. 500mm OptiCom Assist control receiving conveyor 5600 mm two ejectors total length 13 m component marking printer cutting accuracy +/- 0.5 mm transport dimensions (length / width / height) 600 / 240 / 190 cm weight ~ 1800 kg

Year of construction: 2010, condition: good (used), Weinig GRECON TURBO S finger jointing line - German production - DTR, CE Hedoin Uulopfx Acnst - year of manufacture 2010 - high efficiency up to 200 elements / min - 28 km / 8h TECHNICAL PARAMETERS: Wood parameters - width 60 - 225 mm - thickness 18 - 48 mm - length 300 - 2000 mm - pressing length 8100 - 16400 mm - power consumption 150 kW - air consumption 3100 Nl/min - suction capacity 14845 m3/h - two milling stations - undercutters - connecting with a dash and a zigzag - loading with a conveyor with spacers - package width 600 mm - divided ironing length Folded machine dimensions - length 42000 mm - width 6000mm - height 2100 mm

Condition: used, Stehle HK 630 (semi-automatic straight knife grinder). Specification: • Maximum tool width 630 mm !!! Hsdpfx Acov T Rkhenjt • Tool diameter planer heads (min-max knife heads) 120 - 340 mm • Grinding wheel spindle speed 2850 rpm • Grinding wheel drive 1,1 kW • Clearance angle 10 - 35° • Coolant tank 28 L • Motor coolant pump 0,28 kW • Connection values, total 2 kW Please check in your junk mail if you do not receive a reply within 24hrs from sending your inquiry !!!

Condition: reconditioned (used), Tenoning spindle 1 St. Number of milling agregates 4 St. Spindle diameter 50 mm control Weinig, PC-Nexus Weinig Unicontrol 6 with NC spindles ----- Machine will be cleaned and completely checked before delivery Technical data summary (please enquire about any additional accessories included) Item 1: Cross-cut saw ----- > Electronic cross-cut saw, infinitely adjustable horizontally > Number of tools: 1 piece > Spindle speed: 2,800 rpm Hedpevu Hfqjfx Acnjt > Spindle diameter: 40 mm > Max. tool diameter: 400 mm > Motor power: 3.0 kW > Laser aiming light for detecting the saw section > NC length stop, mounted on slot table included Positioning of the cross-cut saw integrated in the control system. > Length 3500 mm Item 2: tenoning spindle ----- > Number of tools: variable, infinitely variable adjustment NC axis > Tool clamping length: 320 mm > Vertical spindle stroke: variable, infinitely variable adjustment 254 mm NC axis > Spindle speed: 3500 rpm > Spindle diameter: 50 mm > Max. tool diameter: 320 mm > Motor power: 11 kW Item 3: 1st profiling spindle (synchronous spindle and counter-rotation) > Position: vertical right > Number of tools: 1 pc. > Tool clamping length: 120 mm > Spindle speed: 6000 rpm > Spindle diameter: 50 mm > Max. tool flight circle: 232 mm > Motor power: 7.5 kW Item 4: 2nd profiling spindle ----- > Position: vertical right > Number of tools: variable, infinitely variable adjustment NC axis > Tool clamping length: 320 mm > Vertical spindle stroke: variable, infinitely variable adjustment 254 mm NC axis > Spindle speed: 6000 rpm > Spindle diameter: 50 mm > Tool flight circle max.: 232 mm > Motor power: 11 kW 2 feed rollers opposite the spindle, axially pneumatically controlled, 2 positions Rung guide consisting of: Guide ruler in the stop (area of ??synchronous spindle), Rung support bar from above in the area of ??profile milling unit vertical right and profiling spindle. Pos. 5: Profile milling unit horizontal top ----- > Clamping length: 40 mm > Spindle diameter: 40 mm > Motor power: 3.0 kW > Speed ??5,850 rpm > Tool flight circle max. 130 mm > Axial adjustment range 30 mm, 8 positions using pneumatic turret > Radial adjustment range 125 mm, 8 positions using pneumatic turret Pos. 6: 3rd profiling spindle (fitting spindle) ----- > Position: vertical right > Tool clamping length: 160 mm > Axial adjustment range 115 mm, 8 positions using pneumatic turret > Radial adjustment range 100 mm, 8 positions using pneumatic turret > Spindle speed: 5,850 rpm > Spindle diameter: 40 mm > Max. tool flight circle: 210 mm > Motor power: 3.0 kW Other features ----- > online-capable > rebating device for tear-free rebating > double parts package > return conveyor for 1-man operation: tilting belt > screen control > inclined window device > electronic angle display for inclined windows > industrial PC, PC control/NEXUS > Weinig type production program > without processing tools No original images available yet. Images show identical machines from our archive. ----- Price of the above-mentioned machine upon request! ----- Optional with additional charge: EUR 6.500,00 Note on used tools: We currently have used...

Condition: excellent (used), High speed moulder infeed comprising a freestanding flat magazine in front of a high speed moulder. The infeed magazine is driven by hydraulic motors powered by an 5.5kW hydraulic unit (max 140m/min). Hedpswgbxzefx Acnjt A buffer of feedstock is alligned laying flat side by side on the chain cross feeder. The chain feeder transports parts across to the fence. The part next to the fence is detected by a light beam and the the first roller is raised to allow entry and the transport roller then pushes the workpiece under the feed rollers of the planer. The first feed roller of the planer needs to be freewheeling roller to allow operation of the EM814.

Year of construction: 2003, condition: used, Technical data: - Manufacturer: Weinig Hsdpfsyatffex Acnot - Type: Unimat Super 4 - Year of manufacture: 2003 - Working width: 25 - 150 mm - Working height: 15 - 50 mm- Shaft arrangement: Spindle 1 below: Planing and milling the guide groove 125x40x40 mm, Z=2 125x120x40 mm, Z=2 Spindle 2 above: Combination tool consisting of special planing head with guide groove and 2 flat milling cutters. Precise thickness planing and flat milling of the gluing surfaces on the right and left. Face milling cutter on the right: 240x17x40mm, Z=8 Special planing head: 125x240x40mm, Z=4 Face milling cutter on the left: 240x80x122mm, Z=8 Tool flight circles 125 and 250mm Spindle 3 below: Removing the guide groove and finish planing. 125x170x40mm, Z=4 - Spindle 1: 11 KW - Spindle 2: 18.5 KW - Spindle 3: 5.5 KW - Feed engine: 2.2 KW - Feedspeed: 5-20 m/min. - Speed spindle 1 and 3: 6.000 rpm. - Speed spindle 2: 7.000 rpm. - Transport rollers D (hardened): 140 mm - Length of infeed table: 2.000 mm - Hardened machine tables - Guide groove in machine table - Suction nozzles 2x140 mm, 1x160 mm - Volume flow: approx. 5,500 m³/h - Volts/Hz: 400/50 - Location: Blomberg warehouse from 01/2026

Condition: reconditioned (used), Tenoning spindle 1 St Number of milling agregates 4 St. Spindle diameter 50 mm Control Weinig, PC-Nexus Weinig Unicontrol 10 CNC - Spindles radially and axially CNC-controlled ----- The machine was factory overhauled by Weinig in 2024. The control panel was also upgraded to a Siemens S 7 677 C, with a new membrane panel "Touch". With the following machining units: Crosscut saw ----- with laser alignment light, motor power 3 kW, spindle diameter 40 mm, spindle speed 3,000 Axially adjustable via NC axis Radial pneumatic adjustment to 8 positions for edge rounding from above Unit from below for edge rounding ----- Axially adjustable with crosscut saw Tenon and slotting spindle ----- Motor power 15 kW Spindle diameter 50 mm Spindle speed 2,925 rpm Tool travel radius min. 380, max. 400 mm Tool clamping length 640 mm Axially adjustable CNC axis Axially adjustable travel 580 mm Adjustment speed 100 mm/sec. 1. Profile spindle (up- and down-rotation) ----- Motor power 11 kW Spindle diameter 50 mm Spindle speed 6,000 rpm Tool clamping length 400 mm with counter bearing Axially and radially adjustable via CNC axis 2. Profile spindle ----- Motor power 11 kW Spindle diameter 50 mm Spindle speed 6,000 rpm Tool clamping length 400 mm with counter bearing Axially and radially adjustable via CNC axis Profile milling unit horizontally mounted on top ----- Hedpfx Aoxpi Duscnjt Motor power 3 kW Spindle diameter 40 mm Spindle speed 9,000 rpm Pneumatically adjustable to 8 axial and radial positions Profile milling unit vertically mounted on the right side Machine end ----- Motor power 3 kW Spindle diameter 40 mm Spindle speed 5,850 rpm Pneumatic adjustment to 8 axial and radial positions Additional accessories ----- CNC-controlled length stop, mounted on the slotting table for lengths up to 3,500 mm, including a positioned cross-cutting saw integrated into the control system. Studio window device, pivots 60° on both sides Double-part package with automatic separation and transfer Synchronization device with automatic window rebating Rebating carriage for rebating small sash widths Air conditioning unit in the control cabinet PC control NEXUS Automatic turning system Slat conveyor, including conveyor belt for returning the workpieces to the operator (Technical specifications according to the manufacturer - without guarantee).

Condition: used, Weinig Profimat 23 automatic planing and moulding machine for four-sided planing and profiling of timber, with a mobile spindle. Technical data: - Spindles: 5 - Spindle 1: Bottom / 5.5 kW / 40 mm - Spindle 2: Right / 5.5 kW / 40 mm - Spindle 3: Left / shared motor with #2 / 40 mm - Spindle 4: Top / 7.5 kW / 40 mm - Spindle 5: Bottom / 4 kW / 40 mm - Working width: 230 mm - Working height: 120 mm Hedpfx Aox Ecguecnot

Condition: used, Year of construction: 1998, total width: 2,000 mm, total height: 1,800 mm, Colour: Grey Empty weight: 5.000 kg Dimensions (LxBxH): 450 x 200 x 180 cm Four-sided planer Weinig Unimat 23 Year of construction 1998 Serial number 82747 Feed speed 5/36 m/min Workpiece width min/max 20/230mm Workpiece height min/max 8/160mm Spindle diameter 40mm Half Groove Bed 1st spindle bottom: 7.5kW 2nd spindle right: 7.5kW 3rd spindle left: 7.5kW 4th spindle top: 7.5kW 5. Spindle bottom: 7.5kW 6. Spindle universal: 11kW Total power 55kW Total 119Amp Fuse 125Amp. Transport dimensions: 4500x2000x1800 (LxWxH) weight +/- 5000kg - Year: 1998 - Documentation available: No - CE certificate present: No - Serial number: 82747 - Number of spindles [pcs.]: 6 - └ Spindle 1: - - Spindle type: Bottom - - Motor power [kW]: 7.5 - - Spindle diameter [mm]: 40 - └ Spindle 2: - - Spindle type: Right Hodpfx Aswnh D Tjcnet - - Motor power [kW]: 7.5 - - Spindle diameter [mm]: 40 - └ Spindle 3: - - Spindle type: Left - - Motor power [kW]: 7.5 - - Spindle diameter [mm]: 40 - └ Spindle 4: - - Spindle type: Top - - Motor power [kW]: 7.5 - - Spindle diameter [mm]: 40 - └ Spindle 5: - - Spindle type: Bottom - - Motor power [kW]: 7.5 - - Spindle diameter [mm]: 40 - └ Spindle 6: - - Spindle type: Universal - - Motor power [kW]: 11 - - Spindle diameter [mm]: 40 - Min. planing width [mm]: 20 - Max. planing width [mm]: 230 - Min. planing height [mm]: 8 - Max. planing height [mm]: 160 - Feed speed: - └ Min. feed speed [m/min]: 5 - └ Max. feed speed [m/min]: 36 - Current consumption [A]: 119 - Fuse [A]: 125 - Power [kW]: 55.0 - Transport dimensions: 4500mm x 2000mm x 1800mm (l x w x h) - Transport weight [kg]: 5000kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 1969, Used machine Year of manufacture: 1969 Runs perfectly Max. working width: 170 mm Max. working height: 130 mm 1st shaft: bottom 2nd shaft: right 3rd shaft: left 4th shaft: right 5th shaft: top Availability: short-term Storage location: Röllbach Hodjxavtqopfx Acnjt

Condition: used, Cabin for Weinig Unimat 300 Hjdexga E Depfx Acnst

Condition: good (used), Year of construction: 2003, functionality: fully functional, 1.High-Speed Planer/Moulder WACO MAXI 8 spindles for horizontal splitting, feed speed 20-150 m/min Working width planing: 30-300 mm Working height planing: 10-150 mm Cutting circle- 180-260 mm Operating voltage: - 400 Volts, 50 Cycles Main feed motor - 37 kW Frequency concerter - 45 kW 1.Bottom head - 24,5 kW 2.Top head - 30 kW 3.Right side head - 18,5 kW 4.Left side head - 30 kW 5.Right side head -18,5 kW 6.Left side head - 24,5 kW Horizontal splitting: 7.Right side head - 53 kW 8.Left side head - 53 kW Max working width 200 mm Max working height 63 mm Max saw blade diameter 300 - 400 mm Spindle diameter 50 mm Vertical adjustability 10 mm Spindle speed 5.500 v/min Exhaust connection 2 x Æ 160 mm Unit lenght 1300 mm 2. High-Speed Planer/Moulder WACO MAXI 3 spindles for finishing, feed speed 30-300 m/min Main feed motor - 37 kW Frequency converter - 45 kW Feed speed, variable: 30-300 m/min 1.Beading head: 24,5 kW Hedpfx Acjyzq Rconst 2.Top head 24,5 kW 3.Rotaplan head 30 kW

Condition: used, Year of construction: 2004, total height: 1,600 mm, total length: 1,250 mm, total width: 1,400 mm, Colour: Grey Empty weight: 900 kg Price: On request - Details: - └ Description: Bad bearings - Year: 2004 - Documentation available: No - CE certificate present: No - Serial number: 102850 - Motor power: 1.0kW - Transport dimensions: 1250mm x 1400mm x 1600mm (l x w x h) - Transport weight [kg]: 900kg Hedpjyr Rnzjfx Acnot - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, functionality: fully functional, Weinig Rondamat 960 PowerLock cutterhead grinding machine Max. tool width: 240 mm Grinding wheel diameter: 150 – 225 mm Spindle speed, adjustable via frequency inverter: 1500 – 3000 rpm Angle adjustment – radial on the knife back: 10 – 30° Lateral adjustment in manual mode: 0 – 20° PowerLock tool clamping system This precision knife grinding machine is designed for: Hjdpfxszhbruo Acnet – Sharpening and manufacturing profiled knives from solid material according to a template – Re-sharpening straight planing knives in a cutterhead

Condition: good (used), Year of construction: 1981, For inquiries: Zoltán Utasi Plus 36 30 205 7380 pindle configuration: Bottom Right Left Top Bottom Spindle speed: 6000 rpm Working width: 170 mm Hodpfx Ajy Nmv Decnjt Working height: 120 mm Jointing table length: 2 m Equipped with Waxilit pump Infinitely variable feed speed: 7–18 m/min Side pressure roller Motorized pressure beam adjustment Equipped with 5 cutter heads (3 pcs L180 mm, 2 pcs L130 mm) Machine documentation available

Condition: used, Year of construction: 1999, total height: 1,800 mm, total length: 5,700 mm, total width: 2,300 mm, Colour: White Weight: 2.000 kg Hjdpfx Acezmxvzsnst - Year: 1999 - Documentation available: No - CE certificate present: No - Serial number: 10.7488 - Main motor power [kW]: 6.3 - Max. saw length [mm]: 5200 - Max. saw width [mm]: 360 - Max. saw blade diameter [mm]: 600 - Input table length [mm]: 5200 - Output table length [mm]: 3300 - Options: Automatic pusher system - Transport dimensions: 5700mm x 2300mm x 1800mm (l x w x h) - Transport weight [kg]: 2000kg - Transport packages [pcs.]: 2 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Weinig Unimat 300 four-sided planer Working width: 230 mm Working height: 130 mm Number of spindles: 4 Spindle arrangement: 1. Bottom 2. Left Hsdpfx Acozgfxconot 3. Right 4. Top 5. Bottom Two feed speeds: 6-12 m/min Pneumatic pressure pads Illustrative photo; availability starting in July.

Condition: excellent (used), functionality: fully functional, Weinig Profimat 23 Fortec four-sided planer Working width 230mm Working height 140mm Number of spindles 6 Arrangement of spindles Bottom 7.5kw Right Left 11kw Hodpfoumxqrsx Acnjt Top 7.5kw Top 5.5kw Bottom 5.5kw Pneumatic pressures Feed speed adjustable on variator Drive on cardan shafts CE certificate

Condition: used, Year of construction: 1996, Weinig Hydromat 23 Technical data Working width 30 - 230 mm Working height 19 - 200 mm Spindle down, right, left, up, down u- re-li-o-u.o Hedpfxoqrt Eko Acnot without infeed machine only Machine is dismantled, immediately available Transport can be organized

Year of construction: 2004, condition: excellent (used), Dimter optimization crosscut saw 350 with elevation AH 1400 mm crosscut see picture crosscut saw control cabinet Scanner interface sorting 6500 mm long 3 pushers Waste flap Hedpfxencc Ics Acnjt Machine is already dismantled and immediately available Machine ran without problems until dismantling Transport can be organized