Used Twin 65 for sale (10,005)

Condition: ready for operation (used), Year of construction: 2013, Nominal width: 3000mm, Working width range: 600mm-2800mm, Layers: 1, Number of chambers: 6, Heating system: Gas, Air supply: top/bottom, Max. working speed: 100m/min, Chain arrangement: horizontal, Cooling cylinders: 2, Padder: twin cylinder Matex 6000, Exhaust fan: 1, Documentation available, On site inspection is possible. Bodpfx Ajyhqb Todreli

Condition: used, Handgriff Applikator für Kisten, Tray, six-pack Bodpfexytx Rex Adrsli

Condition: good (used), Twin Ribbon Mixer Fully Stainless Steel Bsdpoqu Uykefx Adreli Mixing Chamber Dimensions 1500mm Long x 1100mm Wide x 700mm Deep

Condition: ready for operation (used), Year of construction: 2014, operating hours: 15,662 h, functionality: fully functional, travel distance X-axis: 620 mm, travel distance Y-axis: 520 mm, travel distance Z-axis: 460 mm, controller model: Heidenhain TNC530i, spindle speed (max.): 12,000 rpm, TECHNICAL DETAILS Travel range, X-axis: 620 mm Travel range, Y-axis: 520 mm Travel range, Z-axis: 460 mm C-axis: 360° B-axis: -50° / +110° Rotary table diameter: 500 mm Spindle speed (max.): 12,000 rpm Spindle type: SK40 Number of spindles: 1 Number of tool positions in the tool magazine: 30 MACHINE DETAILS Control system: Heidenhain TNC530i Operating hours (see image) Control system operating hours: 38,569 h Machine operating hours: 37,263 h Spindle operating hours: 15,662 h EQUIPMENT Documentation/Manual Speed infinitely adjustable Chip conveyor Scraper-type chip conveyor Workpiece measuring probe Coolant system Compressed air via M-command Heidenhain handwheel Kinematic optimization cycle Note: The machine is sold without tools, vise, and clamping plate. Bsdpfx Aszd Aitsdreli

Year of construction: 1995, condition: ready for operation (used), functionality: fully functional, power: 52 kW (70.70 HP), screw conveyor diameter: 49 mm, machine/vehicle number: DE27566, TECHNICAL DETAILS Capacity: 150 – 250 kg/h Screw diameter: 2 x Ø 49.7 mm L/D ratio: 32D MACHINE DETAILS Motor power: 52 kW (DC) Control system: analog, contactor-controlled system EQUIPMENT Synchronous motor Degassing Blodpfxezd Scpj Adrei Vacuum pump

Condition: used, Year of construction: 2013, x-travel 735 mm y-travel 650 mm z-travel 560 mm control 840D sl FD operate Siemens turning speed range - main spindle max. 18.000 min/-1 power capacity - main spindel 35 / 24 kW max. Torque 119 Nm tool taper HSK-A63 DIN 69893 table diameter 680 mm max. table load 600 kg max. workpiece sizes 650 x 650 x 500 mm swivellable +/- 120 ° rotatable 360 ° number of toolpositions 30 pos. tool taper HSK-A63 max. tool diameter 80 mm max. tool-dia with free toolbox 160 mm max. tool length 315 mm max. tool weight 8,0 kg change-time chip to chip ca. 4,9 sec feed speeds max. 40.000 mm/min rapid traverse 40 m/min total power requirement 65 kVA weight of the machine ca. 11,6 t dimensions of the machine ca. 4,0 x 3,0 x 2,95 m 5 Axis CNC - MachiningCenter Universal DMG - DMU 65 FD monoBLOCK - Swivel-Rotary-Table - without tools - only 8,444 operating hours - only 2,246 spindle hours - Air blast cooling through spindle center - MDynamics package Bedpfx Aszipzysdroli - Power failure safety package - Coolant ring jet: 7x air jets, 13x water jets - Tropical package (35° – 50° Celsius) - Coolant unit (ICS) with two pressure levels: 40 and 80 bar - Use of special tools (18 kg / 370 mm)

Condition: used, Year of construction: 1987, pressure 65 t distance between columns 930 mm stroke 1100 mm distance table/ram, stroke up 1300 mm table surface area 1340x1084 mm hole in the table 604 x 404 mm table height over floor 1000 mm side window 705 mm ram surface 1230 x 990 mm speed down 620 mm/s speed up 207 mm/s working speed 320 mm/s oil volume 450 l power requirement 15,5 kW weight 8,0 t dimensions (WxDxH) 2,8 x 2,6 x 4,85 m SPECIAL DEAL as is where is, NOT CHECKED Bledpfjvuk Szjx Adrji WITHOUT putting into operation / WITHOUT additional work free loaded to truck

Condition: ready for operation (used), Year of construction: 2011, operating hours: 39,205 h, travel distance X-axis: 735 mm, travel distance Y-axis: 650 mm, travel distance Z-axis: 560 mm, controller manufacturer: HEIDENHAIN, controller model: iTNC 530, spindle speed (max.): 18,000 rpm, number of slots in tool magazine: 30, number of axes: 5, This 5-axis DMG MORI DMU 65 MonoBlock was manufactured in 2011. It features impressive X, Y, and Z travels of 735 mm, 650 mm, and 560 mm respectively, along with a spindle speed of 18,000 rpm. The machine is equipped with a tool changer that has 30 magazine positions and utilizes a Heidenhain iTNC 530 control type. If you are looking to get high-quality machining capabilities, consider the DMG MORI DMU 65 MonoBlock vertical machining centre we have for sale. Contact us for further details. Bljdpfxezidqco Adrsi

Condition: good (used), Year of construction: 1995, - Max. turning diameter: 160 mm - Max. bar diameter: 65 mm - 2 x tool slides, travel 70 mm - 2 x cross slides, travel 70 mm - 8-position turret, non-powered Bjdpfx Aezidcredrsli - Max. main spindle speed: 7,500 rpm - Chip conveyor Accessories - Bar feeder IEMCA TAL 65/32 Dimensions (L x W x H): - Machine with chip conveyor: 4200 x 1385 x 1800 mm - Bar feeder: 4000 x 800 x 1400 mm Total weight: 6,500 kg

Condition: excellent (used), Pfeiffer DUO 65 Two-Stage High-Performance Rotary Vane Pump Here we offer a Pfeiffer DUO 65 two-stage high-performance rotary vane pump. Pfeiffer DUO 65 Two-Stage High-Performance Rotary Vane Pump Two-stage high-performance rotary vane pump with a pumping speed of up to 70 m3/h. With a 3-phase motor. With a temperature sensor (3TF) for optimal motor protection. Integrated gas ballast and HV safety valve. For all applications in the coarse and fine vacuum range. Duo 65, 3-phase motor, 3TF, 200-230 / 346-400V, 60 Hz Type: PK D46 642 A with ONF 35/65 oil mist separator, corrosion-resistant version. It sits on the pump's exhaust nozzle and prevents air pollution by oil mist. Type: PK Z40 150 Scope of delivery: (See picture) We will gladly answer any further questions you may have over the phone. Bedpfxjzianqs Adrsli Written orders can be placed via email or fax.

Condition: used, Unloading at the bottom 2 engines (2 x 37 kW) dimensions (lxwxh): ± 7.300 x 2.280 x 2.600 mm dimensions bowl (lxwxh): ± 4.500 x 2.120 x 1.350 mm suitable for steam injection (double-walled) Bljdpfxoziab Ds Adroi

Condition: excellent (used), CATALOG NUMBER 7881 Technical data: - Cutting height: 30-200mm - Max saw blade diameter: 350mm - Spindle diameter: 70mm - Max cutting width of wood: 500mm - Working width of arbor with saws: 400mm - Minimum length of cut wood: 1000mm *Top: - Anti-kickback devices - 4 toothed feed rollers – pneumatically pressed *Bottom: - Sliding roller - Anti-kickback devices - Toothed feed shaft, 2 pcs - Arbors with saws - Toothed feed shafts, 2 pcs - Infinitely adjustable feed speed via frequency inverter - Feed motor: 3kW - Main motors: 2x55kW - Extraction outlet diameter: 250mm - Machine dimensions (L/W/H): 2150x1880x1800mm - Machine weight: approx. 3500kg ADVANTAGES – Made in Poland – Double-arbor multi-blade saw, 2x55kW – Original DTR + CE documentation – Used multi-blade saw in very good condition Net price: 88,900 PLN Net price: 21,200 EUR (based on the rate of 4.2 EUR) (Prices may change with significant rate fluctuations) Bledpfxezh Ip Te Adroi

Condition: excellent (used), Year of construction: 1999, cutting length 3.200 mm cutting width 3.200 mm cutting hight 65 mm saw blade DM max. 300 mm saw blade motor: 5,5 kW scoring unit DM max. 160 mm motor scoring unit 1,5 kW front support tables 3 Stk. 1 x 2500 x 500 & 2 x 1500 x 500 mm Bledpshvan Ijfx Adroi cutting optimisation program no. of grippers 8 pcs saw blade hight adjustment on THK guides pressure beam with openings side pusher (alignment) saw blade quick change system suction DM1 x 120 & 1 x 150 mm space requirement L x B 5700 x 6000 mm weight approx. 2500 kg INVERTER NEW Advise used machines: • Technical data without obligation, mistake and intermediate sale reserve. • Price is considered ex-location price • All articles or machines are bought as seen without any entitlement on warranty. • It is left to the choice of the buyer to view the machines before at its location. • Special arrangements are possible but only valid in written form. (We answer your inquiries only with stated address + telephone number!)

Condition: used, Year of construction: 2005, Technical details: turning diameter: 275 mm turning length: 900 mm spindle passage: 65 mm power capacity at 100 % load: 25/20 kW spindle turning speed range: 1 - 5000 U/min spindle diameter in front bearing: 110 mm c-axis: 1 - 500 U/min. number of workpiece supports: 4 tool turret: 1 x-axis: 290 mm y-axis: 165 mm z-axis: 360 mm b-axis: 360 ° rapid speed: 18/30 m/min number of tools: 2x2 + 2x2 number of driven tools: 2x2 + 2x2 mm toolpiece turning speed range: 8000 / 2000 U/min power capacity: 25% ED 5,8 kW tool taper: TRAUB 60 tool turret: 2/3/4 x-axis: 170 mm z-axis: 600/950 mm y-axis: +/- 60 mm rapid speed: 18/15/30 m/min number of driven tools: 10 mm toolpiece turning speed range: 1 - 6000 U/min power capacity: 25% ED 5,8 kW tool taper: DIN 69880 40 x 63 total power requirement: 95 kW weight of the machine ca.: 16 t dimensions of the machine ca.: 10,0 x 3,5 x 3,0 m with CNC TRAUB TX 8i, Barloader TRAUB Stamag DNH61 / 3000, Main and Sub spindle with C-axis 1 support with B-axis 3 turret supports dust exhauster, coolant attachment with coalescence-seperator and chip conveyor 2 pc. 3-jaw chuck SMW KNCS-N 170-43 2 pc. HAINBUCH Spanntop chuck 40 pc. various tool holder non-driven 6 pc various tool holder driven Spare parts package * Blodpswp D Nbjfx Adrji

Condition: not inspected (used), Year of construction: 2009, functionality: unexamined, spindle speed (max.): 5,600 rpm, travel distance X-axis: 140 mm, travel distance Z-axis: 520 mm, spindle motor power: 18,500 W, type of input current: three-phase, overall weight: 5,600 kg, bar passage: 42 mm, input current: 85 A, number of tool turrets: 2, number of tool stations in tool turret 1: 14, number of driven tool stations in tool turret 1: 14, number of tool stations in tool turret 2: 14, number of driven tool stations in tool turret 2: 14, CNC Lathe TRAUB TNC 42/65 TECHNICAL CHARACTERISTICS: Year of manufacturing: 2009 CNC control: TRAUB TX8i Number of axes: 8 Stroke Y axis: +/- 35 [mm] Stroke Z1 axis: 450 [mm] Stroke X1 axis: 140 [mm] Stroke Z2 axis: 520 [mm] Stroke X2 axis: 140 [mm] Stroke E axis: 450 [mm] Spindle throughbore: 42 [mm] Max. spindle speed: 5600 [rpm] Increment C-axis: 0.001 [°] Spindle power: 18.5 [kW] Counter spindle throughbore: 42 [mm] Max. counter spindle speed: 5600 [rpm] Counter spindle increment C-axis: 0.001 [°] Counter spindle power: 11 [kW] Type of tool holders: VDI 30 Number of tool stations - Turret 1: 14 Number of tool stations driven - Turret 1: 14 Max. speed driven tools - Turret 1: 4000 [rpm] Number of tool stations - Turret 2: 14 Number of tool stations driven - Turret 2: 14 Max. speed driven tools - Turret 2: 4000 [rpm] Total power required: 107 [kVA] Rated current: 85 [A] Supply voltage: 400 [V] Weight: 5600 [Kg] INCLUDED EQUIPMENT: x1 Set of collets x1 Set of tool holders x1 Chip conveyor x1 IRCO PROFIMAT ECO 42.6 bar feeder x1 KNOLL coolant system Price on request, loading on truck included. Possibility of shipping Worldwide. The information on this page has been obtained by the best of our ability. Therefore, its accuracy can not be guaranteed. Bjdpfx Ajzh D Aijdreli Machine tool similar to turning and milling centers, machining centers and milling machines, including brands such as Schaublin, Index, Mori Seiki, Traub, Tsugami, Star, Tornos, Biglia, Nakamura, Miyano, DMG and Mazak. CNC lathe, CNC turning center, CNC turning machine, machining center, CNC milling machine, CNC machining center, Fanuc, iTNC, TNC, Heidenhain, Mori Seiki, Mazak, Hurco, Nakamura, Takamura, Hardinge.

Condition: like new (used), Year of construction: 2022, operating hours: 850 h, functionality: fully functional, turning length: 610 mm, turning diameter over cross slide: 500 mm, turning diameter: 725 mm, spindle speed (max.): 5,000 rpm, spindle bore: 65 mm, travel distance X-axis: 260 mm, travel distance Y-axis: 80 mm, travel distance Z-axis: 610 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 15 m/min, rapid traverse Z-axis: 30 m/min, feed length X-axis: 260 mm, feed length Y-axis: 80 mm, feed length Z-axis: 610 mm, torque: 250 Nm, bar passage: 65 mm, Equipment: documentation/manual, rotational speed infinitely variable, For sale: As-new EMCO MAXXTURN 65-G2 SMY, year of manufacture 2022, equipped with Siemens Sinumerik ONE with ShopTurn control! CNC turning center for complete machining of turned and milled parts. Features integrated spindle motors and a water-cooled sub-spindle (preloaded roller guides) with Y-axis on both main and counter spindle. State-of-the-art SINUMERIK ONE control with ShopTurn dialogue programming. Main spindle: - Max. bar capacity: 65 mm - Max. torque: 250 Nm - Speed range: 0–5000 rpm Sub-spindle: - Drive power: 22 kW - Max. torque: 130 Nm - Speed range: 0–7000 rpm Turret: - 12-station VDI 30 radial tool turret with directional logic for up to 12 driven tool holders - Max. drive power: 6.7 kW - Max. torque: 25 Nm - Max. speed: 5000 rpm Y-axis travel: +/- 40 mm Includes hollow clamping cylinder with draw tube, C-axis on main and sub-spindle, Sinumerik ONE/OPERATE control, 22" multi-touch display, ShopTurn, 3D simulation, residual material detection, USB interface, electrical cabinet climate unit, reinforced coolant unit (24 bar), chuck flushing (additional pump 3.5 bar), part ejector and flushing through sub-spindle. Hydraulic unit, interface for chip conveyor, documentation and CE certificate. Control language: German/English Electronic handwheel EMCO tool breakage and wear monitoring/SINUMERIK ONE Alternating spindle speed Sub-spindle as tailstock: This cycle allows using the sub-spindle with mounted live center for workpiece support, enabling shaft part machining on machines without a tailstock by using the sub-spindle. Max. thrust force limited to 50% of max. axis force. EMCO PROFI-NET ROBOT INTERFACE: Interface for robot integration using HARTING connector, signal exchange via Profinet, safety signals two-channel/potential-free. Digitalization package for Sinumerik: Condition monitoring SIEMENS ONE INTERFACE for integration with MDE/BDE systems, standard with the following information: - Machine ON - AUX ON - Automatic operation - Production mode - active program - Program running and override between 95 and 105% - Part count impulse (M30) - Programmable impulse (M300) 3D machine data/MT65-G2: 3D data model of the machine included. Bljdpfxsx E Dncs Adroi Pneumatically operated finished part catcher for gentle unloading – parts are transferred into a catch box (standard) or onto a conveyor belt (optional). - Max. finished part length: 175 mm - Max. finished part diameter: 65 mm - Max. finished part weight: 4.5 kg INTERFACE SL1200 HT65-DT/TT + MT65-1000 for connection of EMCO's SL1200 short bar loader. Further options available… Machine is available immediately!

Condition: good (used), Year of construction: 2015, operating hours: 5,381 h, functionality: fully functional, machine/vehicle number: AS0211, total height: 2,400 mm, total length: 4,500 mm, total width: 2,400 mm, overall weight: 9,000 kg, controller manufacturer: FANUC, controller model: SERIES 31 i-MODEL A, Equipment: documentation/manual, Technical specifications: - Operating voltage: 400 V - Frequency: 50–60 Hz - Rated current: 80 A - Control system: FANUC SERIES 31 i-MODEL A Travel ranges: - X1 / X2 axes: 180 mm each - Y1 axis: ±45 mm - Z1 axis: 704 mm - Z2 axis: 620 mm - E2 axis: 720 mm - Rapid traverse X/Y/Z axes: 30 m/min Spindle 1: - Max. speed: 5,000 rpm - Spindle nose: A6k - Spindle bore: 65 mm - Bore in clamping cylinder: 65 mm - Chuck diameter: 210 mm - Drive power: 24 kW Spindle 2: - Max. speed: 7,000 rpm - Spindle nose: Ø 110 mm - Spindle bore: 42 mm - Bore in clamping cylinder: 42 mm Bsdpfx Adsv Uh Ndsrjli - Chuck diameter: 140 mm - Max. chuck jaw weight: 1.25 kg - Output power: 16.5 kW Tool carrier: - 1x 10-station tool turret - 1x 12-station tool turret - All stations driven (12 stations each) - Max. speed of driven tools: 8,000 rpm Accessories: - Chip conveyor from KNOLL - Tool holders (as shown in the photos, included)

Condition: good (used), Year of construction: 2007, operating hours: 88,040 h, functionality: fully functional, machine/vehicle number: 07400003691, turning diameter: 120 mm, spindle bore: 118 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 15 m/min, rapid traverse Z-axis: 30 m/min, total height: 2,500 mm, total length: 5,500 mm, total width: 2,500 mm, overall weight: 11,000 kg, controller manufacturer: SIEMENS, controller model: SINUMERIK 840 D POWERLINE, DMG GILDEMEISTER TWIN 102 CNC Turning and Milling Center - Recorded spindle hours: 43,558 - Spindle speed range: 3,200/5,000 rpm - Swing diameter: 270 mm - Spindle distance: 900 mm - X1 axis travel: 290 mm - Z1 axis travel: 650 mm - X2 axis travel: 180 mm - Z2 axis travel: 650 mm - Y1 axis travel: ±40 mm - Z3 axis travel: 670 mm - X3 axis travel: 175 mm - Max. bar diameter: 100/104 mm - Number of driven tools per tool turret: 12 - Including chip conveyor, with 2 tool turrets (each with 12 tool stations), main and counter spindles, as well as foot switches Attention, the machine has the following defects: - The B-axis is defective (mounted on turret 1) - Guideways and drives show age-related wear - X2 axis (guide rails) runs slightly out of alignment by approximately 0.03 mm (should be re-measured) - Occasionally, axis reference value setting in the control system fails - The hydraulic pump was replaced after a failure and is now installed externally as a standalone unit Bodsyaqgyjpfx Adrjli FCA D-58256 Ennepetal, loaded on truck at a mutually agreed date at the end of February 2026.

Condition: ready for operation (used), Year of construction: 2015, operating hours: 43,196 h, spindle motor power: 25,000 W, spindle speed (max.): 5,000 rpm, bar diameter (max.): 65 mm, total width: 1,990 mm, total height: 2,300 mm, overall weight: 9,500 kg, controller manufacturer: FANUC, controller model: 310, product length (max.): 4,500 mm, number of axes: 8, This 8-axis DMG MORI Sprint 65 linear was manufactured in 2015. It features a maximum main spindle speed of 5000 rpm and a maximum main spindle bar diameter of 65 mm. The machine includes two turrets, each with 12 driven tool positions, and a robust coolant tank capacity of 650 liters. If you are looking to get high-quality turning capabilities, consider the DMG MORI Sprint 65 linear multi-spindle turning machine we have for sale. Contact us for further details. • Total hours: 64274 h; Operating hours: 43196 h • Counter spindle: 17 kW; max speed 5000 rpm; max bar diameter 45 (65) mm • CNC controlled axes: • X1: stroke 165 mm; rapid 30 m/min; acceleration 5 m/s2 • Z1: stroke 678 mm; rapid 30 m/min; acceleration 5 m/s2 • Y1: stroke 80 (+50/-30) mm; rapid 30 m/min; acceleration 5 m/s2 • X2: stroke 165 mm; rapid 30 m/min; acceleration 5 m/s2 • Z2: stroke 640 mm; rapid 30 m/min; acceleration 5 m/s2 • W2: stroke 690 mm; rapid 30 m/min; acceleration 5 m/s2 • Turrets: 2; 12 driven positions per turret; Tool system VDI 30; Max driven tool speed 4000 rpm • Coolant system: tank approx. 650 l; pump capacity per turret 20 l/min; pressure 7 bar • Power supply: 91 kVA • Base machine configuration and functions: • Drive for slide 1 and 2 (all 12 positions) • C-axis for main and counter spindle • Y-axis for slide 1 • Counterspindle collet cleaning with coolant • Mechanical preparation for oil mist filter • Electrical and software interface for bar loader • Angular synchronism between main and counter spindle • Automatic machine shut down • 2 additional on/off outputs (4 M-functions) • Rigid tapping • Piece and time counter • Software for polygonal turning (slide 1 and 2) • Constant cutting speed • Helical interpolation (slide 1) • Spindle speed control • Quadruple warning light • Cooling device for electrical cabinet • Control options: • Tool wear monitoring system (FANUC monitor) • Sister tool selection system (FANUC monitor) Additional equipment • IEMCA MASTER 865 MP 43 L bar feeder • Swarf (chip) conveyor, belt type • Workpiece unloading device including belt • Main spindle collet chuck MPF 65/140 (no axial feed), max Ø 65 mm • Manual collet changer SACO MPT65/140 and MPF65/140 • Counter spindle chuck SMW 175-BBD, incl. adapter • 1 set of soft jaws for SMW 175-BBD Bodpfszhkl Djx Adrjli • Differential clamping pressure for counter spindle (two selectable pressures) • External flushing of jaws/collets with coolant on main and counter spindle • Various new spare parts available Technical Specification Counter Spindle Yes

Condition: ready for operation (used), Year of construction: 2015, operating hours: 42,222 h, spindle speed (max.): 5,000 rpm, bar diameter (max.): 65 mm, total width: 1,990 mm, total height: 2,300 mm, travel distance X-axis: 165 mm, travel distance Y-axis: 80 mm, overall weight: 9,500 kg, controller manufacturer: FANUC, controller model: 310, product length (max.): 4,500 mm, number of axes: 8, This 8-axis DMG MORI Sprint 65 linear was manufactured in 2015. It features a maximum workpiece diameter of 175 mm and a maximum bar diameter of 65 mm. The machine is equipped with two turrets, each with 12 driven tool positions, and offers a maximum spindle speed of 5000 rpm. If you are looking to get high-quality turning capabilities, consider the DMG MORI Sprint 65 linear multi-spindle turning machine we have for sale. Contact us for further details. Bedjzhklwopfx Adreli Control system: CNC 310 isTotal hours: 61295 hOperating hours: 42222 hMain spindle power 20/25 kWCounter spindle power 17 kWMax. main spindle speed: 5000 rpmMax. counter spindle speed: 5000 rpmMax. main spindle bar diameter: 65 mmMax. counter spindle bar diameter: 45 (65) mmCNC CONTROLLED AXESStroke X1 165 mmRapid speed X1 30 m/minAcceleration X1 5 m/s2Stroke Z1 678 mmRapid speed Z1 30 m/minAcceleration Z1 5 m/s2Stroke Y1 80 (+50/-30) mmRapid speed Y1 30 m/minAcceleration Y1 5 m/s2Stroke X2 165 mmRapid speed X2 30 m/minAcceleration X2 5 m/s2Stroke Z2 640 mmRapid speed Z2 30 m/minAcceleration Z2 5 m/s2Stroke W2 690 mmRapid speed W2 30 m/minAcceleration W2 5 m/s2Number of turrets 2Number of rotating tools each station 12 all driven positionsTool system VDI 30Max driven tool speed 4.000 rpmApprox. coolant tank capacity 650 lCoolant pump acity (per each turret) 20 l/minPump pressure 7 barPower supply 91 kVALxWxH of the machine 4.500x1.990x2.300 mmApprox. machine weight 9.500 kgIEMCA MASTER 865 MP 43 L (4m) bar feederBase machine configuration:- Drive for slide 1 and 2 (all 12 pos.)- C-axis for main and counter spindle- Y-axis for slide 1- Swarf conveyor belt type- Counterspindle collet cleaning with coolant- Workpiece unloading including belt- Mechanical preparation for oil mist filter- Electrical and software interface for bar loader- Angular synchronism between main and counter spindle- Automatic machine shut down- 2 additional on/off outputs (4 M-functions)- Rigid tapping- Piece and time counter- Software for polygonal turning for slide 1 and 2- Constant cutting speed- Helical interpolation for slide 1- Spindle speed control- Quadruple warning light- Cooling device for electrical cabinetAdded options:I-V50011 Collet chuck Type "MPF 65/140" without axial feed for main spindle max. diameter: mping elements and other equipment:I-V50025 Manual collet changer type "SACO MPT65/140 and MPF65/140"I-V50092 Differential pressure for counterspindle, possibility of setting two different clamping pressures.I-V50083 1 set of soft jaws for chuck type "SMW 175-BBD"I-V50080 Chuck type "SMW 175-BBD" For counter spindle, including adapter for adapting the spindleI-V60050 Tool holder for drilling tools with internal cooling and cylindrical shank Ø 32mm,with clamping shank according to DIN 69880 (VDI 30) - 4pcsI-V60010 Radial tool holder for external machining type C1 with clamping shank according to DIN 69880 (VDI 30) - 5pcsControl system options:I-V12060 Tool wear monitoring system Monitor for CNC FANUCI-V12070 Sister tool selection system for Tool Monitor for CNC FANUCHydraulic and filtration equipment:I-V40045 External flushing of jaws/collets with coolant on main spindle and counter spindleSpecial optionsSK001 Special clamping device with mandrel for counter spindle product HAINBUCH AXFIX 811 including 2 colletsVarious new spare parts are included. Technical Specification Counter Spindle Yes Driven Tools Yes

Condition: excellent (used), ESPEC TSA-72EL-A Temperature Shock Chamber Manufacturer: ESPEC Corporation Type: TSA-72EL-A Machine Type: Temperature Shock Chamber / Thermal Shock Chamber (2-Zone) Design: Water-cooled For sale is a used ESPEC temperature shock chamber, type TSA-72EL-A. This unit is suitable for reproducible temperature cycling and thermal shock testing in research, development, quality assurance, as well as for testing electronics, automotive components, aerospace parts, and materials. The switchover between the hot and cold chambers is performed automatically via a 2-zone damper system. Technical Data Test chamber volume: approx. 70 liters Internal dimensions (W x H x D): 410 x 460 x 370 mm External dimensions (W x H x D): 1,310 x 1,900 x 1,470 mm Weight: approx. 900 kg Temperature range, hot chamber: +50 °C to +200 °C Temperature range, cold chamber: -65 °C to 0 °C Temperature stability: ±0.5 °C Preheating temperature: up to +205 °C Bodpfx Ajzhkfqjdrjli Precooling temperature: up to -75 °C Heating time: ambient temperature to +200 °C within approx. 15 minutes Cooling time: ambient temperature to -70 °C within approx. 40 minutes Temperature recovery time: ≤ 5 minutes Max. test load: 30 kg evenly distributed Cable entry: Ø 50 mm Compressed air supply: 0.4 to 0.7 MPa (4 to 7 bar) Refrigeration system / Power supply Refrigeration system: Mechanical cascade refrigeration system Refrigerant, high-temperature side: R404A Refrigerant, low-temperature side: R23 Condenser: Water-cooled Mains connection: AC 380 / 400 / 415 V 3 phases / 50 Hz Max. current draw: 45 A Equipment 10.4" TFT color touchscreen PID temperature control Program memory (RAM/ROM) Trend graph Alarm history RS-485 interface Eco mode Automatic defrost Vertical sliding door Stainless steel test chamber 2 stainless steel test inserts Mechanical cascade refrigeration system Electronic expansion valve Sirocco circulation fan Pneumatic damper switchover Cable entry Ø 50 mm Applications Temperature shock testing Temperature cycling testing Electronics testing Semiconductor testing Automotive Materials testing Component testing Quality assurance Research and development Condition Used Optical condition as shown in the pictures. Scope of supply ESPEC TSA-72EL-A Temperature Shock Chamber 2 stainless steel test inserts Accessories as shown in the pictures Scope of supply as pictured. Subject to change, errors and prior sale.

Condition: used, Year of construction: 2014, machine/vehicle number: S6F143651, FANUC 31iB control system, power 29 kW, main and counter spindle, spindle speed max. 5,000/7,000 rpm, travel distances X/Z = 260/610 mm, 12-position tool changer with powered tools (VDI 40), max. turning diameter/turning length = 320/550 mm, part ejector, operating hours approx. 400 hours. Bedpfxoy U R Nxo Adreli

Condition: ready for operation (used), Year of construction: 2008, operating hours: 76,595 h, spindle speed (max.): 7,000 rpm, travel distance X-axis: 160 mm, travel distance Z-axis: 320 mm, controller manufacturer: SIEMENS, controller model: 840D Powerline, number of axes: 7, This 7-axis Gildemeister TWIN 42 was manufactured in 2008. It features a CNC control Siemens 840D Powerline, two 12-station star turrets, and live tooling capabilities. The machine has a tailstock stroke of 230 mm and is equipped with a optional chip conveyor. If you are looking to get high-quality turning capabilities, consider the Gildemeister TWIN 42 horizontal turning machine we have for sale. Contact us for further details. • CNC Control: Siemens 840D Powerline • C-Axis: 2 • Y-Axis: Upper Slide • Cross Slides: 2 • Turrets: 2 × 12-Station Star Turrets • Live Tooling: 2 • Tailstock Mounted on Counter Spindle Slide • Tailstock Stroke: 230 mm • Tailstock Force: 300 daN • Tailstock Center: MT3 • Overload Clutch for X- and Z-Axes • Chip Conveyor: Bürener, optional not included • Tool Monitoring System: Artis CTM • Workpiece Diameter: Ø 6–65 mm • Maximum Workpiece Length: approx. 300 mm Bodpfxezhbtxs Adrjli • Maximum Workpiece Weight: 3.5 kg • Bar Feeder Interface, optional not included • Bar Feeder: IRCO SiMag 42 Technical Specification Counter Spindle Yes Driven Tools Yes

Condition: ready for operation (used), Year of construction: 2004, operating hours: 8,375 h, This 7-axis Gildemeister TWIN 42 was manufactured in 2004. It features a Siemens 840D Powerline CNC control, two 12-station star turrets, and live tooling capabilities. The tailstock has a stroke of 230 mm and a force of 300 daN, making it suitable for workpieces with a diameter of Ø 6–65 mm and a maximum length of approximately 300 mm. If you are looking to get high-quality turning capabilities, consider the Gildemeister TWIN 42 machine we have for sale. Contact us for further details. • CNC Control: Siemens 840D Powerline • C-Axis: 2 • Y-Axis: Upper Slide • Cross Slides: 2 • Turrets: 2 × 12-Station Star Turrets • Live Tooling: 2 • Tailstock Mounted on Counter Spindle Slide Blodpfx Ajzhblhedrsi • Tailstock Stroke: 230 mm • Tailstock Force: 300 daN • Tailstock Center: MT3 • Overload Clutch for X- and Z-Axes • Chip Conveyor: Bürener, optional • Tool Monitoring System: Artis CTM • Workpiece Diameter: Ø 6–65 mm • Maximum Workpiece Length: approx. 300 mm • Maximum Workpiece Weight: 3.5 kg • Bar Feeder Interface • Bar Feeder: IRCO SiMag 42, optional 3 other machines available with following defects: • Machine 1: Hydraulic line defective on turret 1 or 2 • Machine 2: DINA module removed, pressure clamp (reports that the collet is not closed) • Machine 3: Main spindle defective with bearing damage, HS clamp defective, LT module missing, DINA module missing

Condition: ready for operation (used), Year of construction: 2022, spindle motor power: 29,000 W, spindle speed (max.): 5,000 rpm, travel distance X-axis: 530 mm, travel distance Y-axis: 120 mm, travel distance Z-axis: 1,215 mm, overall weight: 620 kg, controller manufacturer: SIEMENS, controller model: Sinumerik ONE, number of slots in tool magazine: 40, number of axes: 6, This 6-axis EMCO Hyperturn 65 Powermill G2 was manufactured in 2022. A highly productive CNC turn-mill center, it features a main spindle and subspindle both with a max torque of 250 Nm and speeds up to 5000 rpm. The milling spindle offers up to 12000 rpm. Includes a 40-position tool magazine, 12-position turret, and advanced Sinumerik ONE control system. If you are looking to get high-quality turning and milling capabilities consider the EMCO Hyperturn 65 Powermill G2 machine we have for sale. Contact us for more information. • Main spindle (direct drive): • Max. torque: 250 Nm • Subspindle (direct drive): • Max. drive power: 29 kN (as provided) • Max. torque: 250 Nm • Speed range: 0–5000 rpm • Milling spindle (direct drive): • Max. drive power: 37 kW • Max. torque: 30 Nm • Speed range: 0–12000 rpm • Tool turret (direct drive): • Max. drive power: 10 kW • Max. torque: 30 Nm • Speed range: 0–12000 rpm • Kinematics and axes: • Cross slide at the top with turning/milling spindle as motor spindle; hydraulic clamping during turning • Y-axis travel: +/- 120 mm Bedpfx Asx D E Hbsdroli • B-axis with direct drive: +/- 120°, hydraulic clamping • Tooling: • 40-position tool magazine, HSK-T63 • 12-position radial turret with direct drive, BMT55P tool interface • Spindles and clamping: • High-clamping cylinder with draw tube for main spindle • Full clamping cylinder with partial hollow clamping 66 x 550 mm deep in counter spindle • Programmable clamping pressure for main and counter spindle • External feed flushing on main and counter spindle • Mechanical holding brake on main and counter spindle • C-axis for main and counter spindle • Control and HMI: • SINUMERIK ONE / OPERATE, EMCONNECT app-based UI • 22" multi-touch display • IPC with 240 GB • SHOPTURN dialog programming • 3D simulation and Drawing • Residual material detection • Unblocking from external memory • CAD reader (DXF import) • TRANSMIT and TRACYL for C-axis programming • USB interface, Network drive (Ethernet) • PC keyboard incl. HMI hotkey • LED status bar • Fluids and utilities: • 2 coolant lines at 25 bar • 2 flushing pumps at 4.3 bar • Control cabinet air conditioning unit • Cooling system for spindle motors, milling spindle, B-axis torque motor, and turret direct drive • Hydraulic unit • Machine light • 8 leveling elements • Feedback/measurement: • Glass scales: X1 (incl. air system), Y1, Z1, X2 (HT65-PM-G2 / 840D-sl) Additional equipment • Chip management and filtration: • Hinged belt chip conveyor, discharge height 1200 mm • Belt filter system, 980 liters • Dirty water pump • Control/monitoring options: • BAOD-SL electronic handwheel (portable, magnetic mount for Siemens controllers) • EMCO tool breakage and wear monitoring / B40D-SL • Wireless probe / HSK drill breakage control BK-MICRO • 4-axis turning / balance cutting (SINUMERIK option) • Alternative-end spindle speed (SINUMERIK option) • Turret as tailstock (SINUMERIK option) • Counter spindle as tailstock (SINUMERIK option) • Bar feeder (specifications as provided): • Bar length: 300–1200 mm • Bar diameter: 10–104 mm • Material support surface (front view): 800 x 1250 mm • Material capacity: 12 bars with 65 mm diameter • Max. load capacity: 400 kg (max. 74 kg/bar) • Rectangular material: min. edge length 6 mm; max. circumference 105 mm • Hexagonal material: SW 5 to 85 mm • Round material: