Used Traub Tvc 200 for sale (107)

Condition: ready for operation (used), Year of construction: 1994, TRAUB TNS 65 D / 5-axis CNC turning-milling center TX8D -TX 8D control system -COMPLETE TECHNICAL DATA – SEE PHOTOS -Year of manufacture: 1994 -Hydrobar tool magazine -Tailstock -Various powered tool holders -Three-jaw chuck -Tool holder -Complete documentation Gbedpfxezpf I Aj Ak Uet Errors and omissions excepted.

Condition: good (used), Year of construction: 2001, TNK 36, year of manufacture 2001 including chip conveyor, Resy filtration system In good condition, operated without loader, not under power Gbedpfxoxv Sr Is Ak Uot

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, Traub CNC turning machine TNC65DGY, TX8I, year of manufacture 2005, serial number 113* Gbedpfxjzfkbae Ak Ust Y-axis on S1, V-axis, 2x C-axis, 2 rotating tool drives, 2 turrets VDI30, Hainbuch BZI65 on main and counter spindle, parts gripper, without loading magazine. Very well maintained, in good condition, maintenance performed. Machine geometry has been checked and corrected/adjusted. Machines can be inspected while powered up – or a video is available. Approximately 4 weeks after order. Warranty of 6 months on main components as follows: Spindle bearing, ball screws, linear guides, clamping cylinders. The warranty expressly applies only to the replacement parts, not to downtime or labor time, or travel time. The warranty expressly does not apply to other parts than those mentioned above, e.g. wear parts, electrical components, electronics, hydraulics, etc.

Condition: good (used), Year of construction: 1990, functionality: fully functional, Traub CNC turning center TNA480, TX8D, year of manufacture 1990, serial number >550. C-axis, rotary tool drive, 1 turret VDI40, tailstock, chip conveyor, hollow cylinder chuck, 3-jaw chuck KNCS315. Good condition, ready for operation. Gjdjzcdgfopfx Ak Uobt Machine geometry has been checked and corrected/adjusted. Scrapers and belts have been inspected, replaced, maintenance performed after 4000 operating hours. The photos were taken in the production environment; the machine will be cleaned and inspected further. The machine can be inspected while powered on.

Condition: used, Year of construction: 2005, Technical details: turning diameter: 275 mm turning length: 900 mm spindle passage: 65 mm power capacity at 100 % load: 25/20 kW spindle turning speed range: 1 - 5000 U/min spindle diameter in front bearing: 110 mm c-axis: 1 - 500 U/min. number of workpiece supports: 4 tool turret: 1 x-axis: 290 mm y-axis: 165 mm z-axis: 360 mm b-axis: 360 ° rapid speed: 18/30 m/min number of tools: 2x2 + 2x2 number of driven tools: 2x2 + 2x2 mm toolpiece turning speed range: 8000 / 2000 U/min power capacity: 25% ED 5,8 kW tool taper: TRAUB 60 tool turret: 2/3/4 x-axis: 170 mm Godewp D Nbopfx Ak Uebt z-axis: 600/950 mm y-axis: +/- 60 mm rapid speed: 18/15/30 m/min number of driven tools: 10 mm toolpiece turning speed range: 1 - 6000 U/min power capacity: 25% ED 5,8 kW tool taper: DIN 69880 40 x 63 total power requirement: 95 kW weight of the machine ca.: 16 t dimensions of the machine ca.: 10,0 x 3,5 x 3,0 m with CNC TRAUB TX 8i, Barloader TRAUB Stamag DNH61 / 3000, Main and Sub spindle with C-axis 1 support with B-axis 3 turret supports dust exhauster, coolant attachment with coalescence-seperator and chip conveyor 2 pc. 3-jaw chuck SMW KNCS-N 170-43 2 pc. HAINBUCH Spanntop chuck 40 pc. various tool holder non-driven 6 pc various tool holder driven Spare parts package *

Condition: not inspected (used), Year of construction: 2009, functionality: unexamined, spindle speed (max.): 5,600 rpm, travel distance X-axis: 140 mm, travel distance Z-axis: 520 mm, spindle motor power: 18,500 W, type of input current: three-phase, overall weight: 5,600 kg, bar passage: 42 mm, input current: 85 A, number of tool turrets: 2, number of tool stations in tool turret 1: 14, number of driven tool stations in tool turret 1: 14, number of tool stations in tool turret 2: 14, number of driven tool stations in tool turret 2: 14, CNC Lathe TRAUB TNC 42/65 TECHNICAL CHARACTERISTICS: Year of manufacturing: 2009 CNC control: TRAUB TX8i Number of axes: 8 Stroke Y axis: +/- 35 [mm] Stroke Z1 axis: 450 [mm] Stroke X1 axis: 140 [mm] Stroke Z2 axis: 520 [mm] Stroke X2 axis: 140 [mm] Stroke E axis: 450 [mm] Spindle throughbore: 42 [mm] Max. spindle speed: 5600 [rpm] Increment C-axis: 0.001 [°] Spindle power: 18.5 [kW] Counter spindle throughbore: 42 [mm] Max. counter spindle speed: 5600 [rpm] Counter spindle increment C-axis: 0.001 [°] Counter spindle power: 11 [kW] Type of tool holders: VDI 30 Number of tool stations - Turret 1: 14 Number of tool stations driven - Turret 1: 14 Max. speed driven tools - Turret 1: 4000 [rpm] Number of tool stations - Turret 2: 14 Number of tool stations driven - Turret 2: 14 Max. speed driven tools - Turret 2: 4000 [rpm] Total power required: 107 [kVA] Rated current: 85 [A] Supply voltage: 400 [V] Weight: 5600 [Kg] INCLUDED EQUIPMENT: Gedpfozh D Aisx Ak Ujbt x1 Set of collets x1 Set of tool holders x1 Chip conveyor x1 IRCO PROFIMAT ECO 42.6 bar feeder x1 KNOLL coolant system Price on request, loading on truck included. Possibility of shipping Worldwide. The information on this page has been obtained by the best of our ability. Therefore, its accuracy can not be guaranteed. Machine tool similar to turning and milling centers, machining centers and milling machines, including brands such as Schaublin, Index, Mori Seiki, Traub, Tsugami, Star, Tornos, Biglia, Nakamura, Miyano, DMG and Mazak. CNC lathe, CNC turning center, CNC turning machine, machining center, CNC milling machine, CNC machining center, Fanuc, iTNC, TNC, Heidenhain, Mori Seiki, Mazak, Hurco, Nakamura, Takamura, Hardinge.

Condition: good (used), Grinding wheel puller, cup wheel puller, double bench grinder puller, surface grinder puller, cylindrical grinder puller, dressing head, dressing head for grinding machines Gsdjd R Ikdepfx Ak Ujbt Quantity: 1 piece available -Dimensions: 325/130/H135 mm -Weight: 7.3 kg

Condition: used, Year of construction: 2001, turning diameter 340 mm turning length 750 mm control SYSTEM TX 8H spindle passage 80 mm swing over plan sled 530 mm greates pass round over bed 665 mm turning speed range - main spindle 3.150 min/-1 drive capacity - main spindle 22 kW number of tool places 12 Pos. In our assessment, the machine is in good used condition and can be inspected under power by appointment. Two machines are available. Gbedpfoxwdw Esx Ak Ujt Price per unit. Machine 1: - Images 1-5 - Operating hours approx. 55,790 h Machine 2: - Images 6-10 - Operating hours approx. 54,347 h Technical Features & Accessories: - Y-axis - Accessory package with rigid and driven tool holders - Chip conveyor Accessories, tools, and clamping devices shown are only included in the scope of delivery if this is noted in the additional information. Subject to changes and errors in the technical data and specifications, as well as prior sale!

Condition: good (used), Year of construction: 1999, operating hours: 110,000 h, functionality: fully functional, spindle bore: 42 mm, Description follows Gjdpfx Aox A Ha Hok Uebt

Condition: ready for operation (used), Year of construction: 2012, operating hours: 19,295 h, spindle motor power: 10,700 W, spindle speed (max.): 8,000 rpm, overall weight: 6,000 kg, total width: 2,500 mm, total height: 2,600 mm, bar diameter (max.): 32 mm, travel distance X-axis: 140 mm, controller manufacturer: TRAUB, controller model: TX 8i-p, product length (max.): 4,500 mm, number of axes: 7, This 7-axis TRAUB TNL 32 P was manufactured in 2012. It features a maximum bar diameter of 32 mm and a maximum Z-axis travel of 305 mm. The machine includes two turrets with live tooling capabilities, offering 10 and 9 tool stations respectively. If you are looking to get high-quality turning capabilities, consider the TRAUB TNL 32 P swiss type turning machine we have for sale. Contact us for further details. • Number of Turrets: 2 • Maximum Z-Axis Travel: 305 mm • Main Spindle Torque: 21 / 32 Nm • Main Spindle C-Axis Resolution: 0.001° • Turret 1 Tool Stations: 10 • Turret 1 Live Tool Stations: 10 • Turret 1 Live Tool Speed: 12,000 rpm • Turret 1 Live Tool Power: 1.5 / 2.5 kW • Turret 1 Tool Holder Diameter: 45 mm • Turret 1 Turning Tool Shank: 16 x 16 mm • Turret 1 X-Axis Travel: 140 mm • Turret 1 Z-Axis Travel: 305 mm • Turret 1 H-Axis Resolution: 0.001° • Turret 1 Chip-to-Chip Time: 0.3 sec • Turret 2 Tool Stations: 9 • Turret 2 Live Tool Stations: 9 • Turret 2 Live Tool Speed: 12,000 rpm • Turret 2 Live Tool Power: 1.5 / 2.5 kW • Turret 2 Tool Holder Diameter: 45 mm • Turret 2 Turning Tool Shank: 16 x 16 mm • Turret 2 X-Axis Travel: 140 mm • Turret 2 Y-Axis Travel: -25 / +40 mm • Turret 2 Z-Axis Travel: 320 mm • Turret 2 Chip-to-Chip Time: 0.3 sec • Counter Spindle Speed: 8,000 rpm • Counter Spindle Power: 1.5 / 2.5 kW • Counter Spindle Torque: 4.5 / 7.7 Nm • Counter Spindle C-Axis Resolution: 0.001° • Maximum Clamping Length: 250 mm • Maximum Bar Diameter (Counter Spindle): 32 mm • Back Working Tool Stations: 8 • Back Working Live Tool Stations: 3 • Back Working Live Tool Speed: 12,000 rpm • Back Working Live Tool Power: 1.5 / 2.5 kW • Back Working Tool Holder Diameter: 36 mm • Rapid Traverse (X / Y / Z): 20 / 20 / 20 m/min • Maximum Feed Rate: 20,000 mm/min • Total Power Requirement: 46 kW • Space Requirement incl. Bar Feeder: 8,000 x 2,500 x 2,600 mm • Chip Conveyor: Optional, not included • Coolant System: Yes • Tool Turrets: 2 • Back Working Unit: Yes • Bar Feeder Interface: Yes Gbsdpfxszcyhxo Ak Uet • Bar Feeder: LNS Hydrobar Express 332 S2 / 3 m • Electronic Handwheel: Yes • Hydraulic Unit: YesMachine defects: The counter spindle is currently unusable due to prolonged inactivity. Either the sensor or the motor is defective. Technical Specification Counter Spindle Yes Driven Tools Yes Through-spindle Coolant Yes

Condition: ready for operation (used), Year of construction: 2003, operating hours: 124,706 h, spindle speed (max.): 6,300 rpm, travel distance X-axis: 370 mm, travel distance Z-axis: 250 mm, spindle motor power: 10,700 W, controller manufacturer: TRAUB, controller model: TX8i (64-bit), number of axes: 6, This 6-axis TRAUB TNK 36 was manufactured in 2003. It features a maximum spindle speed of 6,300 rpm and a main spindle bore of 36 mm. The machine is equipped with advanced capabilities such as tool monitoring, rigid tapping, and a high-pressure coolant system. If you are looking to get high-quality turning capabilities, consider the TRAUB TNK 36 horizontal turning machine we have for sale. Contact us for further details. TECHNICAL DATA • MDE Interface: Yes • Tool Monitoring: Yes • Rigid Tapping: Yes (without compensation chuck) • Main Spindle Bore: 36 mm • Main Spindle Drive Power: AC 6.7 / 10.7 kW • Top Turret Stroke X/Z: 50 / 100 mm • Rear Attachment Stroke X: 73 mm • Rear Attachment Stroke Y: ±50 mm • Main Spindle C-Axis: Yes • Hainbuch Change Parts: Yes • Hainbuch Setup Aid Base Body: Yes • Hainbuch Manual Change Device: Yes • Counter Spindle: Motor Spindle • Counter Spindle C-Axis: Yes • Counter Clamping Pressure Device: Yes • Workpiece Ejection Device: Yes • Hainbuch Axfix Chuck: Yes • Upper Tool Carrier: Yes • Electronic Gearbox: Yes • X3 Cross Axis for Front Unit: Yes • Front Unit: 5-position • Driven Tools on Front Unit: Yes Gjdpfx Aeza Ucxok Ujbt • Cut-Off Side Machining Station: Yes • Driven Tools on Cut-Off Side Station: Yes • Workpiece Unloading Device: Gripper • Coolant Tank Capacity: 230 l • Coolant Pressure: 7 bar • Coolant Flow Rate: 50 l/min • Internal Coolant Supply: 30 bar • High Pressure Coolant: 120 bar (front and rear machining station) • Coolant Filter: Knoll VRF 150/750 Vacuum Rotary Filter • Suitable Materials for Filter: Aluminum, Plastic, Brass, Steel • Wash Gun: Yes • Connected Load: 22 kW • Maximum Bar Length: 3 m • Maximum Bar Diameter: 36 mm • Operating Voltage: 400 V, 3~, 50 Hz • Control Voltage: 24 V AC • Valve Voltage: 24 V DC • Clutch Voltage: 24 V DC • Total Installed Power: 33 kW • Total Rated Current: 60 A ADDITIONAL EQUIPMENT OPTIONAL • FMB turbo 5-42 XT / 3200"C" Bar Feeder • Bar Feeder Year: 2003 • Hinged Belt Chip Conveyor • Chip Conveyor Discharge Height: 950 mm • Guide Tubes D25, D36 • Running Workpiece Stop, Shank 16 × 16 mm • Brankamp CMS 100 Collision Monitoring Technical Specification Through-spindle Coolant Yes Counter Spindle Yes Driven Tools Yes

Condition: good (used), Internal item no.: 25088 Tool holder Thread whirling holder incl. cutting inserts Index / Traub No.: 12068219 The tool was used on a Traub TNL18 Very well-maintained condition! Gbodoxu Dcvopfx Ak Ujt

Condition: used, Year of construction: 1987, Technical details: turning diameter over bed: 180 mm turning length: 490 mm swing diameter: 450 mm cross travel: Z-Weg: 168 mm control: Traub TX8D revolution per minute: 20 - 4000 U/min spindle passage: Ø 60 mm operating hours - idle run: 23.495 h tool turret: 12 tools total power requirement: 38 kW Weight approx.: 4,2 t dimension machine xH: 3,6 x 2,5 x 2,2 m Tool holder straight shank DIN 69880 (VDI 3425) Ø 40x63 Röhm lathe chuck Ø 200mm hydraulic clamping Operation via double foot switch and control panel/operating panel. Coolant device Gbodpfx Akeu Ix N Se Ujt The Traub carries an integrated chip conveyor with an ejection height of 1,100mm (currently without function). Accessories: multiple small parts 8 x machine feet without tailstock i.D. *

Condition: good (used), Year of construction: 1996, CNC turning center TRAUB Type:TNC65 DG Year 1996 Control TRAUB TX8F Gbjdpfeu Eug Iex Ak Uot With lots of accessories.

Condition: good (used), Year of construction: 2003, CNC turning center TRAUB TNK 36 Year of manufacture: 2003 Control: TX8i (64 bit) Flat screen monitor, 10.4 inches Additional V24 RS232 interface in the control cabinet MDE interface in the control cabinet (machine is running, piece counter) Tool monitoring for thread cutting without compensation chuck Main spindle: Spindle bore 36 mm, maximum speed 6,300 rpm Drive power AC 6.7 / 10.7 kW C-axis Quick-change parts Hainbuch, mounting aid, base body Quick-change device Hainbuch, manual Counter spindle: Counter spindle as a motor spindle with C-axis Device for counter pressure, workpiece ejection device, Axfix chuck Hainbuch Tool holder, top, driven tools, electronic gearbox X3 cross axis for front tool holder, front tool holder, 5-position, driven tools Cut-off station, driven tools Workpiece removal device: Workpiece gripper Gripper jaws D5-8, D8-20, D20-36 Coolant system: Tank 230 l / 7 bar / 50 l/min. Internal coolant supply 30 bar High pressure 120 bar at the front and rear machining stations, vacuum rotary filter Knoll VRF 150/750 (suitable for aluminum, plastic, brass, and steel) Coolant gun Hinged belt chip conveyor, discharge height 950 mm Preparation for installation of bar feeder magazine (guide tube D25, D36) Gbsdpfszaud Aex Ak Uet Workpiece stop, rotating (shank 16x16) Collision monitoring Brankamp CMS 100 on main and counter spindle Machine without known defects.

Condition: good (used), Year of construction: 2002, TRAUB TNL 12/7 CNC sliding headstock automatic lathe TECHNICAL DATA Bar capacity: 12 mm Main headstock strokes: 130 / 80 mm Spindle power: 4 kW Speed, main spindle: 12`000 rpm Upper turret: 6 positions Lower turret: 6 positions Number of driven tools, turret: 6 Max diameter, counter spindle: 12 mm Speed, counter spindle: 12`000 rpm Dimensions: 2850 x 1100 x 1480 mm SCOPE OF OFFER U.A: (list not exhaustive): Traub TNL 12/7 CNC lathe Meyrat high-frequency spindles, 2 pieces Gbjdet E Dbyepfx Ak Ujt Tool holders (driven and non-driven) FMB Minimag 3200 C bar loader Hydraulic unit High pressure pump Chip conveyor Exact scope of supply according to photo gallery No responsibility is taken for the correctness, completeness and up-to-dateness of the information.

Condition: good (used), Year of construction: 2009, functionality: fully functional, CNC Lathe TRAUB TNX 65/42 Year of manufacture: 2009 Control: Traub TX 8i-s TECHNICAL DATA - Number of spindles: 2 - Number of axes: 12 - Number of turrets: 2 MAIN SPINDLE - Spindle nose: A2-6 - Spindle drive power: 24 kW - Spindle speed: 5,000 rpm - Max. bar diameter: 65 mm - Max. diameter of main spindle chuck: 175 mm - Minimum C-axis resolution: 0.001 degrees SUB SPINDLE - Spindle nose: A2-5 - Spindle drive power: 28 kW - Spindle speed: 7,000 rpm - Max. bar diameter: 42 mm - Minimum C-axis resolution: 0.001 degrees - Travel: 700 mm LEFT UPPER TURRET - Number of stations: 10 - Number of live stations: 10 - X/Z-axis travel: 175 / 650 mm - Y-axis travel: +/- 40 mm - Tool type: VDI 30 - Driven tools speed: 6,000 rpm - Driven tools power: 5.5 kW RIGHT LOWER TURRET - Number of stations: 10 - Number of live stations: 10 - X/Z-axis travel: 175 / 650 mm - Y-axis travel: +/- 40 mm - Tool type: VDI 30 - Driven tools speed: 6,000 rpm - Driven tools power: 5.5 kW ELECTRICAL SUPPLY - Supply voltage: 400 V - Total power: 95 kW WEIGHT AND DIMENSIONS - Footprint: 5,450 x 2,318 mm - Machine height: 2,258 mm - Machine weight: 10,000 kg New spindle since 04/26 ACCESSORIES - 3-color status signal lamp - Coolant tank: RESY * with high-pressure pump * with paper filter - Chip conveyor - Parts extraction Gbsdpeyw H Szefx Ak Ust - Parts belt conveyor

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, spindle speed (max.): 8,000 rpm, bar passage: 32 mm, controller model: Traub TX8i-S, number of slots in tool magazine: 12, Equipment: chip conveyor, TECHNICAL DETAILS Bar capacity: 26 / 32 mm Max. main spindle speed: 8,000 rpm Axes: X1 / Y1 / Z1, C-axis integrated in the main spindle Gedeyzxp Tspfx Ak Ujbt Turret: 1 Tool stations: 12 Drive power: 6.7 kW (100% duty cycle) / 10.7 kW (40% duty cycle) Torque: 21 Nm (100% duty cycle) / 32 Nm (40% duty cycle) MACHINE DETAILS Power-on time: 116,721 h Operating hours: approx. 48,000 h Control: Traub TX8i-S DIMENSIONS & WEIGHT Dimensions (L × W × H): approx. 4.4 × 1.4 × 1.7 m Machine weight: approx. 4,000 – 4,200 kg EQUIPMENT Chip conveyor: hinged belt, discharge height approx. 950 mm

Condition: used, Year of construction: 2008, turning diameter 12,7 mm Gjdoygm R Ijpfx Ak Ujbt turning length 50 mm control Traub System TX 8i turning speeds 12000 U/min c-axis 0,001° c-axis 0,001 ° gripping station 12,7 mm speeds 12000 U/min rapid traverse 15 m/min turret (x-stations) 6 worktool system 5+3 worktool system 3 Werkzeugsysteme total power requirement 2,5/4 kW weight of the machine ca. 2 t dimensions of the machine ca. 2,4 x 1,1 x 1,7 m CNC turning machine Traub TNL 12K with barloader LNS Tryton 112 Motor drive S8 (rear working with driven tools possible) Motor drive S7 (front working with driven tools possible)

Condition: ready for operation (used), Year of construction: 2007, operating hours: 19,441 h, functionality: fully functional, machine/vehicle number: 6000816, turning length: 50 mm, spindle speed (max.): 12,000 rpm, bar passage: 12 mm, controller model: Mitsubishi TX-8i, counter spindle speed (max.): 12,000 rpm, No reserve price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Turning length: 50 mm Main spindle Gbodpfx Asx Hxv Dsk Ujt Technology: Belt-driven spindle Speed: 12,000 rpm Power: 4 kW Torque: 7 Nm Bar capacity: 12 mm Travel in Z1: 50 mm Workpiece clamping: Collet chuck Counter spindle Technology: Belt-driven spindle Speed: 12,000 rpm Power: 4 kW Torque: 7 Nm Travel in X3/Z4: 222/139 mm Rapid traverse in X3/Z4: 15 m/min Workpiece clamping: Collet chuck Tool Carrier I (X/Y) Technology: Turret with 6 stations (fully driven) Tool holder: Ø25 mm Driven tool speed: 8,000 rpm, 1.5 kW, 2.4 Nm Travel in X1/Y1: 35/37.5 mm Rapid traverse in X1/Y1: 15 m/min Tool Carrier II (X/Z) Technology: Turret with 6 stations (fully driven) Tool holder: Ø25 mm Driven tool speed: 8,000 rpm, 1.5 kW, 2.4 Nm Travel in X2/Z2: 35/50 mm Rapid traverse in X2/Z2: 15 m/min Front Attachment Number of stations: 4 Tool holder: Ø28 mm Station pitch: 32 mm Driven tool speed: 12,000 rpm, 4 kW, 7 Nm Number of driven stations: 4 Travel in X3/Z3: 222/139 mm Rapid traverse in X3/Z3: 15 m/min Rear Attachment Number of stations: 4 Tool holder: Ø28 mm Station pitch: 32 mm Driven tool speed: 8,000 rpm, 1.5 kW, 2.4 Nm Number of driven stations: 4 Travel in X4: 39 mm Rapid traverse in X4: 15 m/min MACHINE DETAILS Control system: Mitsubishi TX-8i Dimensions & Weight Spindle center height above floor: 1,050 mm Dimensions (L x W x H): 1,450 x 1,098 x 1,700 mm Dimensions (L x W x H) with standard coolant tank: 2,355 x 1,098 x 1,700 mm Weight with control cabinet (max. configuration): 2,000 kg Weight without control cabinet (max. configuration): 1,600 kg Weight with control cabinet (min. configuration): 1,200 kg Weight without control cabinet (min. configuration): 850 kg Operating Hours Power-on hours (control): 19,441 h Automatic mode 1: 7,607 h Automatic mode 2: 6,720 h Production time: 38,989 h Total counter: 50,536 h EQUIPMENT Chip conveyor Coolant pump Bar feeder FMB minimag 3200 Workpiece discharge device (tube) Mechanical interface prepared Various fixed holders Rinse gun

Condition: new, 3 safety windows suitable for CNC lathe TRAUB TNA 300 Gedpfsw Edq Dsx Ak Uobt TNA 400 TNA 500 TNC 42 TNC 65 Size: 660 x 480 mm Price: €500.00 / unit net Delivery time: immediately, subject to prior sale Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Year of construction: 2005, condition: good (used), 7-position tool holder for CNC lathes Manufacturer: TRAUB, Model TNA 480, tool holder size VDI 40. Also compatible with SAUTER tool turrets with VDI 40 mounting. 7-position horizontal tool holder, positions no. 3/4/5/6/7/8/9 for drilling and milling, price per piece: 550,- € 2-position horizontal tool holder, positions no. 1 and 2 for tapping, price per piece: 600,- € Godpfx Ajhwnfkok Usbt 1 NC drilling chuck VDI 40, clamping range 1-13 mm, price: 100,- € 1 NC drilling chuck VDI 40, clamping range 2.5-16 mm, price: 150,- €

Condition: ready for operation (used), Year of construction: 2012, operating hours: 8,300 h, functionality: fully functional, spindle speed (max.): 6,400 rpm, bar diameter (max.): 32 mm, controller model: TX 8 i-p, workpiece length (max.): 245 mm, TECHNICAL DETAILS Main Spindle Max. bar capacity: 32 mm Max. workpiece length (swiss turning): 245 mm Max. workpiece length (short turning): 125 mm Max. spindle speed: 6,400 rpm Sub Spindle Max. bar capacity: 32 mm Max. clamping length for workpiece: 250 mm Max. spindle speed: 6,000 rpm Upper Turret Number of stations: 10 All driven Max. speed: 12,000 rpm Lower Turret Number of stations: 9 All driven Max. speed: 12,000 rpm Backworking Unit Number of stations: 8 Driven stations: 3 (T12, T13, and T14) Speed T12 & T14: 12,000 rpm Speed T13: 4,000 rpm MACHINE DETAILS Spindle hours: 8,300 hours Control system: TX 8 i-p EQUIPMENT Gjdpfx Aksyn Imys Ujbt Parts conveyor Chip conveyor Coolant pump 20 bar IFS oil mist separator Bar feeder FMB turbo 3-36

Condition: ready for operation (used), Year of construction: 1996, operating hours: 46,282 h, functionality: fully functional, controller model: TX 8F, counter spindle speed (max.): 4,000 rpm, workpiece diameter (max.): 56 mm, Equipment: bar feeder, chip conveyor, No reserve price – guaranteed sale to the highest bidder! Submitting a bid obligates you to collect the item within the specified period, either between 11/05/2026 and 13/05/2026 or between 18/05/2026 and 21/05/2026. TECHNICAL DETAILS Max. counter-spindle speed: 4,000 rpm Max. workpiece diameter: 56 mm Rapid traverse: max. 15 m/min Fine interpolation cycle: 0.34 ms Maximum thread pitch: 999,999 mm Maximum radius: 99,999.999 mm Feed override: 0–200% Rapid traverse override: 0–100% Gbsdpfeym A E Iox Ak Uot Spindle speed override: 50–120% Workpiece removal via counter spindle Programming: EIA and ISO code Input/output resolution: X/Z: 0.001 mm, C-axis: 0.001° C-AXIS Main spindle: Max. speed: 80 rpm Torque at 100% duty cycle: 100 Nm Accuracy: +/- 3 arcmin Counter spindle: Max. speed: 80 rpm Torque at 100% duty cycle: 30 Nm Accuracy: +/- 3 arcmin Tool Turret 1 & 2 Driven tools per turret: 10 (14) Max. speed: 4,000 (8,000) rpm Power at 100% duty cycle: 1.5 kW Power at 15% duty cycle: 4 kW Torque at 15% duty cycle: 12.4 (4) Nm Number of tool holders per turret: 10 (14) Cylindrical shank as per DIN 69880: Ø 30 x 55 (25 x 48) mm Tool cross-section: 20 x 20 (16 x 16) mm Chip-to-chip time according to VDI 2852: 1.2 s Index time per station: 0.6 s Over 5 stations: 1.5 s Counter spindle (numerically controlled in Z-direction) Max. speed: 4,000 rpm Max. clamping diameter: 65 mm Continuously programmable AC motor: 11 kW Torque: 210 Nm Feed force at 100% duty cycle: 6,000 N Feed travel: 520 mm Ball screw: Ø 32 x 10 mm MACHINE DETAILS Control: TX 8F Operating voltage: 400 V Frequency: 50 Hz Control voltage: 230 V Rated current: 85 A Connection: 54 kW Connected load: 39 kW Noise emission at operator station: 71 dB(A) Hydraulics System pressure: 60 bar Tank capacity: 150 l Coolant Per tool turret: single-stage centrifugal pump Pump pressure: 5/12 bar Tank capacity without chip conveyor: 300 l Tank capacity with chip conveyor: 280 l Dimensions & Weight Dimensions (L x W x H): 11,000 x 2,000 x 2,600 mm Weight: 6,000 kg Read operating hours: 46,282 h EQUIPMENT STAMAG bar feeder Chip conveyor Hainbuch chucking system Two 10-station turrets with driven tool stations Counter spindle External reference: L. Schaible

Condition: ready for operation (used), Year of construction: 2014, spindle speed (max.): 8,000 rpm, number of axes: 9, This 9-axis TRAUB TNL 32 swiss type turning machine was manufactured in 2014. It features a TX8i-s control with a 64-bit RISC CNC/PLC processor, color TFT display, and electronic handwheel. The main spindle supports a 32 mm bore, and the machine includes a sub-spindle with a C-axis. It offers a dual-driven upper tool turret and a lower turret with nine tool holders. Consider the opportunity to buy this TRAUB TNL 32 swiss type turning machine. Contact us for more information. Godpfx Asx D Drcok Uebt • Control: TRAUB TX8i-s CNC/PLC with 64-bit RISC processor and fiber-optic PC; color TFT flat-panel display; electronic handwheel • Software/extensions included: Polyform (C-axis programming), Helical (3D Y-axis interpolation), tapping without compensating chuck, parting tool breakage monitoring, parting tool ejection monitoring, axis shutdown, T-ATC • Main spindle: Motor spindle with hollow clamping system; 32 mm bore/bar capacity; C-axis max speed 8,000 rpm • Max stroke: 305 mm (L version) / 127 mm (K version) • Sub-spindle: Partial hollow clamping, C-axis; cleaning unit mounted on lower tool turret • Upper tool turret: X/Y/Z/H/B axes; 10 tool holders; dual drive • Lower tool turret: X/Y/Z/H axes; 9 tool holders; combined drive; separate counter-spindle operation • Measuring/feedback: Glass scales on X-axis (upper and lower turrets); rotary encoder on C-axis • Back working: 8-position back table with combined drive for up to 3 tools; prepared for internal coolant supply • Clamping: Clamping direction reversal device and counter clamping pressure device on main and counter spindles • Coolant system: Standard system with 3-bar and 8-bar pumps (50 Hz) in a 500-liter tank; additional 28-bar pump (50 Hz), 19 l/min flow rate • Extraction: Connection D 150 mm for central extraction Additional equipment • None specified (no robots, bar feeder, chip conveyor, or external automation listed)