Used Slitter Rewinder for sale (318)

Year of construction: 1996, condition: ready for operation (used), A complete slitting line Burghardt & Schmidt including a Grindingmaster is available. Uncoiler load capacity: 3000kg, expansion range: 375mm-420mm, knife inner/outer diameter: 80mm/180mm, separator disc dimensions X/Y/Z: 130mm/80mm/1.5mm, recoiler load capacity: 2500kg, usable width: 250mm, cutting performance: 0.1/0.3/0.5/0.8, cuts: 25/20/12/25, material strength: 1800N/m². System dimensions X/Y/Z: approx. 11000mm/5600mm/2000mm, weight: approx. 8000kg. Dokumentation vorhanden. An on-site inspection is possible. Hfsdpfx Agjxxzizotjl

Condition: refurbished (used), SLITTING LINE INMASA 1100x3 Revamped in 2019 Scope of supply 1. Loading carriage for coil up to 15000 Kg 2. Cantilever Uncoiler with hold down roll 3. Threading group with supporting roll + Pinch roll 4. Crop shear 5. Intermediate table 6. Pinch-roll 7. Circular shear (turning unit with 2 pairs of arms, one in-line + one off line for preparation) 8. Exit roll table 9. Scrap recoiler 10. Accumulator pit + Tiltable cover 11. Tensioning device with Strip guiding arm 12. Recoiler 13. Unloading carriage 14. 2-arms turnstile 15. Switch cabinets & control panels (New in 2019) 16. Pneumatics & Hydraulics 17. Existing tooling SCOPE OF THE WORKS CARRIED OUT DURING THE REVAMPING OF THE LINE MADE BY EUROMAQUINA IN 2019 · Complete disassembly for overhaul and cleaning of each line component · Final paint touch up. · Electrical disassembly of each component. · Checking of the elements for defects. · Overhaul of motors. · Conductivity, brush cleaning in DC motors, etc. were checked. Not repairable motors were replaced. · Mechanical assembly of the line components. · Assembly of components to be replaced due to defective parts. · Revision of hydraulic cylinders with change of seals. Cleaning and painting. · Overhaul hydraulic motors. Cleaning and painting. · Overhaul hydraulic power units. Cleaning and painting. · Overhaul of pneumatic cylinders and electro-valves. Hodpoymbplsfx Agtefl · Replacement of defective hydraulic piping and hoses. · Replacement of pneumatic piping. · Change all wiring on board machine. · Replace defective boxes on board the machine or paint them. Coil weight: 15.000 kg Coil outer diameter: 1650 mm Coil inner diameter: 508 / 610 mm Strip thickness: 0.4 – 3 mm Coil width: 150 - 1100 (1060) mm Ultimate tensile strength: 600 N/mm2 Yield strength: 500 N/mm2 Exit coil weight: 15.000 kg Exit coil diameter: 700 – 1550 mm Exit coil inner diameter: 508 mm Exit coil width: 31 – 1100 mm Max. cutting speed: 150 m/min Disc blades diameter (inner-outer): 160 – 300 mm

Year of construction: 1998, condition: excellent (used), Max. roll diameter, unwinder: 750 mm (Shaft 76) Max. roll diameter, rewinder: 320 mm Max. web width: 270 mm Hsdezn Ayyspfx Agtsfl Description: Unwinder, splicing table, 2x web guiding system, cutting unit, rewinder, counters (meters), Nikka camera Camera Manufacturer: Nikka Research Deutschland GmbH Type: ALIS C2 Date: 2005 Description: Since May 13, 2026, the camera has only been working intermittently (outdated hardware). Although it could be repaired, the chances of success are low; the manufacturer recommends installing a new camera system. Accessories: 1x Shaft rewinder 76 mm 1x Shaft rewinder 40 mm 1x Shaft rewinder 50 mm 1x Shaft rewinder 100 mm 10x Razor blades

Condition: good (used), Year of construction: 2021, functionality: fully functional, machine/vehicle number: SM2021609, type of input current: three-phase, total width: 1,900 mm, total length: 3,800 mm, input voltage: 380 V, power of the servo motor: 4,000 W, overall weight: 2,150 kg, For sale: an exceptionally well-preserved and minimally used semi-automatic folder gluer machine for corrugated boxes, manufactured by HEBEI SOOME. The machine was manufactured in 2021, installed in late 2022, and officially activated for production in 2023. Available now due to plant closure. Hedpfx Agozil Tljtjfl This heavy-duty machine (over 2 tons) is highly reliable and capable of high-speed gluing for large formats of corrugated board (up to an impressive 2800 mm width). Key Technical Specifications: Manufacturer: HEBEI Soome Packaging machinery co., ltd. Machine Type: SOOME SMZX-2800 Year of Manufacture: 2021 (Activated: 2023) Max Cardboard Width: 2,800 mm x 1,500 mm Operating Speed: 0 - 75 m/min Power Supply: 3×380 V/AC, Installed power 4.0 kW Machine Dimensions: 3,800 x 1,900 x 1,700 mm Machine Weight: 2,150 kg The machine is located in Slovenia (Celje region). The electrical installation was renewed in 2023; the unit is connected to power and ready for inspection. The buyer is responsible for dismantling and transport. Other cardboard manufacturing equipment are also available printing machine (Flexo Printer EMproject 89), paper slitting and rewinding machine YYS-I, year 2023, fully automatic folder gluer with bottom-locking capability by HEBEI SOOME (2024) and fully automatic folder gluer machine for corrugated boxes by HEBEI SOOME (2019) are also available for sale.

Year of construction: 2011, condition: like new (used),  Year of manufacture: 2011  Servo drive  Job memory up to 50 jobs  Register control: Semi- and fully rotary  electronic motor control  Electronic web edge control  Waste and misprint stop  Unwind shaft: d=76mm  Unwind diameter: 700mm  Rewind shaft: d=76mm  Rewind diameter: 550mm  Automatic web stop at machine stop Hfedpfx Ajpyg Tbjgtol  Flexo printing unit GALLUS EM 340  Web width: 340mmm  Cliché 1.14mm  Fully rotary register control including servo drive  Die-cutting and printing of materials  UV drying  Web width: 410mm  Laminating  Pressure station mounted on printing cylinder  Punching unit LeoMat L  Adaptation of the GALLUS R250 magnetic cylinder  Rotometrics impression cylinder  Grid rewind servo driven  Integrated edge trim suction  Including fully rotative register control

Condition: excellent (used), Year of construction: 1979, functionality: fully functional, KAMPF (LONGITUDINAL SLITTER) Hjdpfx Aszktycsgtefl Desscription:: Year 1979, width 1600 mm, speed 600 m/min Machine is in very good condition and can be seen in production!

Year of construction: 1995, condition: good (used), Max. roll diameter, unwinder: 700 mm (Shaft 76) Max. roll diameter, rewinder: 450 mm Hfedpfxozn Azwe Agtsl Max. web width: 330 mm Max. speed: 220 m/min Description: Unwinder, splicing table, web guiding system, cutting unit, rewinder, counters (labels or meters), missing label detection with visual inspection.

Condition: used, Year of construction: 2020, operating hours: 290 h, functionality: fully functional, number of ink cartridges: 5, color channels: CMYK+2W, resolution (max.): 1,200 dpi, paper weight (max.): 4,500 g/m², paper width (max.): 1,600 mm, paper height (max.): 40 mm, number of feeding trays: 1, total length: 3,480 mm, total width: 1,630 mm, total height: 2,410 mm, year of last overhaul: 2024, type of input current: AC, input current: 30 A, input voltage: 220 V, Equipment: documentation/manual, EFI 16H Pro UV LED Hybrid Printer – Premium 1.6m Industrial System Professional Grade Large Format Printer | Competitive Pricing | Immediate Availability Model EFI 16H Pro UV LED Hybrid Print Width 1.6 meters (16H designation) Hsdpfx Agsxup Tgotefl Color Configuration CMYK + 2 White Resolution 1200 x 1200 dpi (professional quality) Print Speed Up to 91 m²/hour Ink Technology UV LED curable pigment ink Printing Modes 4-pass (outdoor durability), 6-pass (POS applications) Installation Date July 2021 Installed Age 4 years (meticulously maintained) Total Output 5,500 m² (tracked via ERM system) Included Equipment & Accessories EFI Control Software Suite – Latest drivers and management tools Machine Controller – Integrated system for scheduling and color management Flatbed Tables – Two precision flatbed work surfaces for rigid media Roll-to-Roll System – Motorized unwinder and motorized rewinder for continuous roll media Complete Documentation – Manuals, maintenance logs, technical support information Condition & Maintenance History Overall Condition: 90% – Excellent working order Printhead Status: One Cyan printhead requires cleaning (routine maintenance) Mechanical: All systems operational and well-maintained Cosmetic: Professional appearance, consistent with industrial facility use Can assist with transport preparation and truck loading for a small fee

Condition: ready for operation (used), Year of construction: 2017, functionality: fully functional, machine/vehicle number: 828-043, total width: 1,800 mm, number of ink cartridges: 8, color channels: 7, number of print heads: 64, The Kornit Allegro is a powerful textile printing machine that offers outstanding print quality, high speed and versatility. It is particularly suitable for textile printing companies that want to produce first-class prints in large quantities (roll-to-roll) on a wide variety of fabrics. To date, it has been used primarily for cotton fabrics: jersey, French terry, cotton woven fabrics, canvas, sweat and viscose & modal qualities. For sale due to business downsizing. The textile printing machine is currently still in operation and can be viewed at any time by appointment. The following are available for sale with the machine: main and backup air compressors, dryer, unwinder & rewinder. So a complete production line. We are also selling all available spare parts, colors, etc. Technical specifications: Ink type: Kornit NeoPigment Intenso, water-based Hfjdpfsvmdw Ijx Agtsl Ink capacity: 4 liters Colors: Cyan, magenta, yellow, black, red, green, gray Print heads: 64 x Spectra Polaris, recirculating - (7 color channels, 1 channel for pre-treatment) Print width up to 180 cm Print speed: Up to 200m²/ hour Print modes: Multiple print modes from 400-1200 dpi Recommended print mode: 600 x 600 dpi in 6 passes in interlaced mode Weight: 3500 kg Power supply: 110/220V, 60/50 Hz, 40A, 3Ph+N+GND 25kW Media transport: High-precision, adhesive belt conveyor system Fabric feed system: Axial unwinding device with adjustable fabric width and Tensioning mechanisms Max media thickness: 15 mm Max roll width 180 cm Max roll outer diameter: 40 cm Max roll weight: 50 kg Compressed air: 6-8 bar/ < 0.4 m³/min

Condition: like new (used), Year of construction: 2024, functionality: fully functional, machine/vehicle number: SM240101, type of input current: three-phase, total width: 3,500 mm, total length: 14,000 mm, input voltage: 380 V, power of the servo motor: 15,500 W, overall weight: 7,000 kg, cutting length (max.): 1,650 mm, For sale: practically new, fully automatic folder gluer with bottom-locking capability by HEBEI SOOME. 2024 model in excellent condition, ideal for high-demand packaging. Type: Automatic Folder Gluer, Bottom Locking Type Year: 2024 Hodpfx Agozil Nyotsfl Effective Width: 1650 mm Power: 15.5 kW Condition: Excellent, like new. The machine is located in Slovenia (Celje region). The buyer is responsible for dismantling and transport. Other cardboard manufacturing equipment are also available printing machine (Flexo Printer EMproject 89), paper slitting and rewinding machine YYS-I, year 2023, fully automatic folder gluer machine for corrugated boxes by HEBEI SOOME built in 2019 and semi-automatic folder gluer machine for corrugated boxes, manufactured by HEBEI SOOME,manufactured in 2021 are also available for sale.

Condition: good (used), Year of construction: 2015, functionality: fully functional, machine/vehicle number: P240207155, BWU 1100 (2015) Hjdpfxey Rzhds Agtsfl BWU 1100 (2017) Maximum air pressure: 600 kPa Euroline – optimized for garbage bag production - Basic converting line for garbage bag manufacturing with non-driven C-folder - Can be configured in-line or off-line – with or without surface unwinder - Flexible unit, easy to operate and maintain - Servomotor drive - Combination of proven FAS converting modules - Double-sided sealing with single sealing bar - Unique tension-free sealing system - Optionally equipped with PP insert and TU220 tape unit Information sourced from online documentation (also enclosed with this advert) Max. main roll diameter, mm [in]: 800 [31.5] Max. sealed tape width, mm [in]: 1060 [41.7] Bag length, min-max, mm [in]: 600-3000 [23.6-118] Machine speed, m/min [fpm]: 20-100 [65.6-328] C-bend, mm [in]: 220-620 [8.7-24.4] Max. cycles/min: 160 Web rewinding, mm [in]: 100-500 [3.9-19.7] Max. roll changes/min: 8 Max. roll diameter, mm [in]: 200 [7.9] Installed power, kW [A]: 5 [9] Air supply, bar [psi]: 6, 13 l/roller change [87 to 3.7 scfm] L x W x H, mm [in] BWU: 4487 x 2157 x 2356 [177 x 85 x 93] Weight, kg [lbs] BWU: 2540 [6350] * Mechanical. Maximum output speed depends on the material being processed. With TU220 belt unit: max. 6/min. Price per machine. Please note that this description may have been automatically translated. Contact us for further details. The information in this classified ad is for guidance only. We recommend verifying details with the seller prior to purchase.

Condition: like new (used), Year of construction: 2024, functionality: fully functional, Equipment: documentation/manual, KONICA MINOLTA ACCURIOLABEL 230 Digital Label Printing Press • Manufacturer: Konica Minolta • Model: AccurioLabel 230 • Year of manufacture: 2024 • Machine has been continuously maintained under a service contract _____ TECHNICAL SPECIFICATION Printing System • Digital toner-based label printing system • Resolution: 1,200 × 1,200 dpi × 8 bit • Equivalent image quality up to 1,200 × 3,600 dpi • Maximum print image size: 1,195 × 320 mm • Web width in present configuration: 325 – 333 mm Production Speeds Depending on substrate: Hjdpezx Ri Dofx Agtefl • 23.4 m/min • 18.9 m/min • 13.5 m/min • 9.45 m/min The machine has mainly been operated at 13.5 m/min, as the current owner achieved the preferred print quality at this speed. All four production speed levels are available. _____ CONTROLLER • Konica Minolta IC-605B • Integrated controller • Operator screen • Direct PDF printing from USB stick possible • Patlite LR4-PP signal tower _____ UNWINDER / REWINDER The machine is supplied complete with: • Integrated BST web guiding system • BST web guiding at both winding units This provides stable and accurate web transport throughout the production process. _____ OVERPRINT EQUIPMENT The machine is equipped with: • Overprint Kit with impression / registration sensor This allows accurate overprinting onto previously conventionally printed label material, making the machine particularly interesting for hybrid production environments. _____ WEB CLEANING & STATIC CONTROL Included: • Web cleaning system for AccurioLabel • Static Eliminator • SWG-400 antistatic brush These systems support clean substrate handling and reliable production, particularly when processing sensitive label materials. _____ SLITTING EQUIPMENT Included: • Longitudinal crush knife system • 3 pneumatic knives • Knife holders According to the present owner, this equipment has never been used. _____ COMPRESSED AIR EQUIPMENT Included:

Condition: like new (used), Year of construction: 2023, functionality: unexamined, machine/vehicle number: 230101, Ladies and Gentlemen, on behalf of our customer, we are selling the model ES-950SF ELCOMA wrapping machine described and photographed here. We will be pleased to provide you with the exact specifications for this winding machine by e-mail. Also available via WhatsApp. Hsdpfx Aervz R Dogtofl This is an advertisement for information purposes only. The purchase contract can only be concluded at the specified location of the purchased item.

Condition: used, Year of construction: 2019, functionality: fully functional, Flexographic printing machine Rotary Print 260 from 2019, Tech-Wash Hedpfxjxrdb Hj Agtefl 8 UV colours Manual colour registration Web guiding control One die-cutting station Web width: 250 mm Max. roll diameter on unwinder: 1000 mm Max. roll diameter on rewinder: 1000 mm Max. roll diameter (matrix) on rewinder: 500 mm Machine working speed up to 120 m/min depending on material type Units for web-turning, peel-off, lamination included Comes with 10 anilox rolls, 7 sets of printing cylinders, and 7 magnetic cylinders. Machine is 100% operational and in continuous use.

Year of construction: 2016, condition: used, Equipment: 1) Cartes GE362VR finishing machine, infeed unit: servo-driven pneumatic 76mm clamping mandrel/expansion shaft, accommodates rolls up to 800mm in diameter or 150kg, automatic electronic web tension and roll diameter control with photocell, automatic stop function at end of material, electronic web guide with ultrasonic sensor for precise web control, splicing table with pneumatic clamps, adhesive tape dispenser, photocell for detecting print marks and any contrast points on pre-printed material, complete servo motor control of the material web, Vetaphone corona treatment system, flexo coating unit, fully rotary operation, equipped with laminating module, rotary flexo coating unit, UV dryer, specification in the source document: 24W/cm / 160W/cm, for laminating, printing or full-surface overcoating/coating, 2) Semi-rotary die-cutting unit with Image Distortion System (IDS) and Air Gap System (AGS): die-cutting system, magnetic cylinder, air-gap adjustment system, semi-rotary and fully rotary gearless die-cutting system, printing plate/die plate thickness range: 0.2-2mm, Image Distortion System (IDS), 3) Air Gap System (AGS), 4) outfeed unit, web control, complete servo motor control of the material web, slitting unit, 10 pivoting razor blades with lateral adjustment, additionally 8 knife/counter-knife cutting groups for longitudinal slitting, rewinding shafts, first rewinding shaft, independent servo-driven pneumatic 76mm expansion shaft, for rolls up to 800mm or 150kg, automatic web tension control, direction of rotation: clockwise/counterclockwise, with documentation. An on-site inspection is possible. Hedpfxozy Rv Te Agtsfl

Condition: used, Year of construction: 2016, For sale Duplo 746 Cutter creaser. Year 2016 Top Spec with extra optional Modules includes: CPM-04 RTM-04 Current product, fully supported by Duplo offering support, Supply of spare parts and supported! 1 owner from new, Previous client paid 90K new!! Very nice condition. These new cost £90k Plus, Machine is in stock in my warehouse. Inspecting and testing welcome in Tadley Reading. The Duplo DC-746 Cutter Creaser is Duplo’s most powerful and versatile slitter, cutter, and creaser, designed to handle high-volume production with precision and speed. Ideal for applications like business cards, brochures, and intricate direct mail pieces, it streamlines complex finishing tasks in a single pass. With advanced features, including a high-capacity feeder, automated setup for up to 30 jobs, and lightning-fast speeds of up to 50 sheets per minute, the DC-746 ensures maximum productivity. Its enhanced feeding mechanism supports a wide range of paper types, delivering unparalleled accuracy even for digital stocks prone to curl or static. The DC-746 is expandable with optional modules for rotary perforating and cross-perforating, making it a perfect choice for PSPs looking to increase efficiency, reduce manual intervention, and produce premium-quality finished products. Specification and Features Machine Dimensions W 3040mm x D 870mm x H 1730mm (with PC) Automated Set-up From barcode In-feed Paper Size Min: 210mm x 210mm Hjdpjzx Htfofx Agtsfl Max: 370mm x 670mm Creases Max. 20 per sheet Cuts Max. 30 cuts per sheet Slits Six (standard) (8 with options fitted) Ideal for Business cards Folded flyers Tickets Perforated vouvhers

Condition: used, Year of construction: 2013, functionality: fully functional, machine/vehicle number: 4514927-4514928, Printed manuals are available both for the SLAU 80-60 shrink wrapper and the TR 65-150 shrink tunnel. Automatic “L” sealer packaging machine, brand ULMA, model SLAU, equipped with a shrink tunnel, designed for packaging all types of products using either shrink film or non-shrink film, reaching outputs of up to 45 cycles/min. Hfedpsykqhfefx Agtjl Highly versatile machine: its simple adjustment systems allow for rapid adaptation to different products to be packaged. Produces seamless packages on both the top and bottom of the product, ensuring high product visibility, whether shrink wrapping is applied or not. The SLAU was specifically designed to facilitate frequent size/format changes, and therefore features systems that enable all changes to be carried out easily and quickly, with no need for additional tools. Automatic in-line feeding via conveyor belt, featuring product separation and alignment, as well as manual belt width adjustment. Motorized 90° film reel holder, with mechanical perforation system and end-of-film detection. Manually adjustable former triangle height. Horizontal and vertical photocells for product detection. Three film sealing and cutting options: STD: by nichrome wire, OPC: knife or hot bar for PE films. The latter two feature electronic temperature control. Jaw opening adjustment by pneumatic actuator in three positions, increasing output with low-profile products. Sealing die equipped with safety end-pieces to prevent products from getting stuck should obstacles be encountered along the path. Belt closure system facilitates the transfer of small and/or unstable products. Sealing center alignment via jaw height adjustment. Easy-access automatic film waste rewinder with film break detector. Function and parameter control and adjustment via programmable PC. Sturdy frame built from painted welded steel tubing. Fitted with wheels and adjustable feet for transport and positioning. Right-to-left machine version. Easy integration into existing production lines. Full accessibility to all components. Ventilated electrical cabinet. Guards and safety systems compliant with CE regulations. Available in both painted and stainless steel versions. --- ULMA TR 65-150 hot air tunnel, designed for film shrink-wrapping of products discharged from side-seal wrappers, bundlers, flow packers, overlap, and other types of packaging machines. High thermal efficiency tunnel, low consumption, and minimal heat loss. Robust frame built from painted rolled steel. Easily integrated into existing production lines. Fitted with wheels and adjustable-height feet. Right-to-left working direction. Electronic adjustment of temperature and conveyor speed. Homogeneous distribution system of hot air flow inside the chamber to ensure significant energy savings. Maximum insulation minimizes heat loss.

Condition: excellent (used), Cut to length - Slitter input width 1250mm Hedpezyyt Iefx Agtofl thickness; 0.35-2.2mm input coil : 6.5ton, output 6.5 ton.

Year of construction: 2012, condition: excellent (used), functionality: fully functional, For sale: SMAG E-CUT S 330, a robust, versatile, and high-productivity roll-to-roll label finishing system. Designed for digital and conventional printing lines seeking flexibility, precision, and premium value-added finishes. This equipment is ideal as a complement to digital presses, enabling lamination, die-cutting, slitting, and rewinding in a single workflow. -> General data: - Model: E-CUT S 330 - Year of manufacture: August 2012 - First installation: February 2013 - Maximum web width: 330 mm - Maximum unwind roll diameter: 700 mm - Maximum speed: up to 35 m/min -> Configuration and Units: - Unwinder with ultrasonic web guide - Fully rotating flexo station - Lamination unit - Semi-rotary die-cutting with Z 160 magnetic cylinder - K&B GapMaster for precise adjustments - Corona treatment for improved adhesion - Longitudinal slitting unit with up to 10 knives - 2 rewinders - Matrix rewinder -> UV System: In 2017, an air-cooled Phoseon UV-LED lamp was installed, improving energy efficiency and reducing maintenance. -> Key strengths: - High industrial productivity and reliability - Great versatility for both digital and flexo jobs - Precise and stable die-cutting - Ready for a wide range of materials Hfjdpfxsyapy Eo Agtol - Ideal for short to medium runs with quick job changeovers -> Equipment condition: - Machine in good working order, well-maintained and operational. - Available for inspection and testing without obligation. Reason for sale: Restructuring / change in production strategy.

Condition: good (used), Year of construction: 2019, functionality: fully functional, machine/vehicle number: 1907, type of input current: three-phase, total width: 2,050 mm, total length: 22,100 mm, total height: 1,350 mm, input voltage: 380 V, power of the servo motor: 10,000 W, overall weight: 6,500 kg, cutting length (max.): 2,300 mm, For sale: high-performance, fully automatic folder gluer machine for corrugated boxes by HEBEI SOOME. Built in 2019, this machine is designed for fast, automated production of large-format packaging. Due to its automated feeding and folding system, it is ideal for demanding industrial operations. Key Technical Specifications: Manufacturer: HEBEI Soome Packaging machinery co., ltd. Machine Type: Folder Gluer (Automatic Type) 1400x2800 SMZX-QZD-2800 Model: 1400 x 2800 Year of Manufacture: 2019 Effective Width: 2,800 mm Voltage: 380 V Condition: Operational, robust industrial design, ready for sale. The machine is located in Slovenia (Celje region). The buyer is responsible for dismantling and transport. Other cardboard manufacturing equipment are also available printing machine (Flexo Printer EMproject 89), paper slitting and rewinding machine YYS-I, year 2023, fully automatic folder gluer with bottom-locking capability by HEBEI SOOME. 2024 and semi-automatic folder gluer machine for corrugated boxes, manufactured by HEBEI SOOME (2021) are available for sale. Hedjzimggepfx Agtjfl

Condition: good (used), Year of construction: 2018, functionality: fully functional, machine/vehicle number: 03-2018, For sale: perfectly preserved and fully operational semi-automatic flexo printing machine for corrugated board, manufactured by the renowned EMproject 89. Built in 2018, this machine is designed for reliable and precise 2-color printing on cardboard packaging. Hfsdjzilvgjpfx Agtol The machine is currently connected to power, fully functional, and ready for work. It is ideal for printing logos, barcodes, and graphics on shipping, industrial, or transport boxes in a single pass. Key Technical Specifications: Manufacturer: EMproject 89 (Serbia) Model: FLEXO PRINTER MS-1700/1400 Year of Manufacture: 03 / 2018 Number of Colors: 2 (Two-color printing) Maximum Cardboard Format: 1700 mm x 1400 mm Voltage: 220 V Condition: Fully operational, well-maintained, testing possible before purchase. The machine is located in Slovenia (Celje region). The buyer is responsible for dismantling and transport. Price is negotiable for serious buyers upon inspection. We also have other cardboard manufacturing equipment available printing machine (Flexo Printer EMproject 89), automatic paper slitting and rewinding machine YYS-I ( 2023), automatic folder gluer machine for corrugated boxes by HEBEI SOOME built in 2019, fully automatic folder gluer with bottom-locking capability by HEBEI SOOME ( 2024) and semi-automatic folder gluer machine for corrugated boxes, manufactured by HEBEI SOOME (2021) are also available for sale.

Condition: ready for operation (used), Year of construction: 2008, functionality: fully functional, Offer without obligations. Duplo system 5000 - year 2008 Specifications Complete stitching line. DSF - 2000 sheet feeder SCC Slitter cutter Creaser System 5000 collator System 5000 Dynamic Booklet maker System 5000 Trimmer Counter 200.000 , very low counter. (Machine is from School) very well maintain. Hfjdpezv U Npjfx Agtol 2 x touch screen , was changed 2 years ago. - See first pictures (Ask for more detailed pictures !) Price ……… UNDER REQUEST

Year of construction: 2020, condition: good (used), functionality: fully functional, DESCRIPTION/FEATURES: 5-color offset printing press for labels, with an inline flexo unit and die-cutting. The machine is equipped with: Hfedpfx Agszrxdpotjl • Unwinding unit • BST web guide • UV LED drying (5) • Turning bar • Offset units: 5 • Flexographic unit • BST registration camera • Automatic washing system • for ink rollers • Automatic plate loading system • Semi-rotary die-cutting unit with magnetic cylinder • Rewinding unit with slitting (blades) • (shearing) • Inking console + CIP 3 for automatic color adjustment • Cooling unit for ink fountains • CCD plate punching table • Automatic registration

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, machine/vehicle number: S/N78757, total width: 1,850 mm, total length: 1,850 mm, total height: 1,650 mm, space requirement width: 10,000 mm, space requirement length: 52,000 mm, space requirement height: 3,000 mm, type of input current: AC, operating speed: 5,580 mm/s, input voltage: 440 V, The Sheet Wizard 1850 dual rotary sheeter is engineered to accommodate a variety of application requirements. This versatile and standardized sheeter features dual rotary knife technology, providing exceptional cut quality for materials up to 1000 gsm. The machine is capable of operating at a maximum speed of 335 meters per minute (1100 feet per minute). Unwind System Six shaftless floor pickup unwinds are designed to handle rolls with a diameter of up to 83 inches. The system supports core sizes ranging from 3 inches up to 12 inches, ensuring flexibility for different roll specifications. Decurling and Tension Control Each unwind is equipped with overhead decurlers and tension controls, maintaining optimal sheet flatness and consistent tension throughout the process. Alignment and Splice Management Hfodpfx Agey Dkikstsl The machine incorporates FIFE alignment technology and a splice sensor detector, which automatically discards joined sections to ensure product integrity and continuous operation. Slitting Capabilities The Sheet Wizard includes a double set of four slitters, each capable of cutting up to 600 grams. This arrangement allows for efficient slitting and high throughput.

Condition: used, functionality: fully functional, power: 650 kW (883.75 HP), total length: 48,000 mm, total width: 8,720 mm, total height: 6,464 mm, Year of construction: 2019, HIGH-CAPACITY 3-LAYER CO-EXTRUSION FLAT SHEET LINE (2100 mm) Manufacturer: FONG KEE INTERNATIONAL MACHINERY CO., LTD. (Taiwan) Model: TSE-90/150/150-2400 Year of Manufacture: 2019 Condition: Used – Excellent condition, fully assembled and preserved indoors. KEY SPECIFICATIONS & PERFORMANCE: • Finished Sheet Width: Up to 2,100 mm (Net trimmed width) • Die Lip Width: 2,300 mm • Output Capacity: Up to 1,000 kg/h (depending on resin and sheet thickness) • Processable Materials: PET, PMMA, ABS, PS (HIPS / GPPS), PC, PP • Polymer Versatility: Configured for engineering thermoplastics and polyolefins (PET, PMMA, ABS, PS, PC, PP sheet extrusion). CO-EXTRUSION & FEED SYSTEM: • Configuration: 3-Layer Co-Extrusion (A/B/A or A/B/C) • Extruders: - Extruder A: Ø 90 mm - Extruder B: Ø 150 mm - Extruder C: Ø 150 mm • Melt Delivery: MAAG Gear Melt Pumps with Dynisco pressure transducers for ultra-stable flow • Extrusion Die: EDI (Nordson) Ultraflex HRC100-FB (2,300 mm, Made in USA) with Fast Gap patent adjustment CALENDER & DOWNSTREAM PROCESSING: • Polishing Stack: 3-Roll horizontal calender with high-precision mirror-finished rolls • Additional Roll Included: Dedicated Matte Calender Roll included with the line • Surface Finish Capabilities: Both High-Gloss / Mirror Optical Grade and Anti-Glare / Matte Finish • Temperature Control: Multi-zone thermoregulation units (TCU) • Protection: In-line dual-side protective masking film application unit • Cutting & Stacking: High-speed automated cross-cutter and automatic sheet stacker unit • Winding: In-line heavy-duty rewinder unit ELECTRICAL, DRIVES & AUTOMATION: • PLC System: Siemens SIMATIC (ET 200SP) with intuitive touchscreen HMI • Frequency Inverters: Siemens Sinamics G120 drive system • Main Electrical Switchgear: Schneider Electric • Cabinets: Independent air-conditioned industrial electrical enclosures FACILITY & FOOTPRINT: Hodpfxszzdnfo Agtefl • Total Line Length: Approx. 48.0 m • Total Line Width: Approx. 8.7 m • Connected Drive Power: Approx. 650 kW (988 A) • Layout Drawing: Full technical CAD layout available upon request. CURRENT STATUS & INSPECTION: • Condition: Fully assembled, idle, and preserved indoors within a controlled industrial environment. • Availability: The complete line is immediately available for professional on-site visual inspection upon request. • Reason for Sale: Facility line reconfiguration.