Used Slide Sanding for sale (9,504)

Condition: used, Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Iijdpfx Aet Tqy Ejfioh Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Condition: used, Year of construction: 1996, operating hours: 12,171 h, Price: On request BOERE sanding line 'Compact' Elite Year of construction 1996 (CE) 12171 Operating hours Maximum height 150 mm Maximum width 1300 mm Elite BKKS 1300 First generator 45kW engine Second generator 30kW engine Third generator 18.5kW engine Voltage 380V, 183Amp Elite TKKS 1100 First generator 45kW engine Second generator 30kW engine Third generator 18.5kW engine Voltage 380V, 172Amp Revised by Boere in 2019 - Bottom sander: - Max. working width [mm]: 1300 - Max. working height [mm]: 150 - Motor power first unit [kW]: 45 - Motor power second unit [kW]: 30 - Motor power third unit [kW]: 18.5 - Sanding pad present: No - Top sander: - Motor power first unit [kW]: 45 - Motor power second unit [kW]: 30 - Motor power third unit [kW]: 18.5 - Structuring brush present: No - Sanding pad present: No - Year: 1996 - Documentation available: No - Operating hours: 12171 - Voltage [V]: 380 - Current consumption [A]: 172 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Iijdpfxewnh Eqo Afioh Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Edge sanding machine Gartner FLK 4 - used - including mitre fence ----- Technical Data ----- Sanding belt width: 200 mm, sanding belt length: 2,350 mm, worktable dimensions: 870 x 400 mm, belt speeds: 4, extraction nozzle Ø: 80 mm, motor: 3 kW Iiedpfxsxd U Uhs Afish

Condition: used, Year of construction: 2018, operating hours: 7,556 h, Serial number: K7xxxx Please contact ATS Norway for more information Please provide reference number upon request: 18475 Specifications: Model year: 2018 Approx. 7,750 hours Will be certified upon sale Operating weight: ~30,350 kg Power: 159 kW Undercarriage (see pictures) S70 quick coupler Tiltrotator Grading bucket, digging bucket & trenching bucket Iisdsvg A E Depfx Afijh Topcon GPS system Track width: 60 cm Machine width: 318 cm Full service history Central lubrication Refueling pump 360° camera Work lights Air conditioning Radio Ready for delivery Description:Well-equipped 2018 Komatsu PC290 with documented service history.Delivered with tiltrotator, GPS, and three buckets.Certified before handover – ready for immediate delivery. Hours: 7556 Own weight: 30350 Total Weight: 30350 Kw: 159 Model: PC290LC-11

Condition: good (used), Year of construction: 2004, gross working tank volume: 350 liters useful volume: 170 liters largest possible workpiece dimension (measured diagonally): 220mm Iodpfx Aet E R Rhjfisih total weight: 731kg drive power at 1500 rpm: 2,6kW

Condition: used, Empty weight: 25 kg Article nr.: W328999052-veiling Ijdpfx Afoxhy U Ueijih Used slide valve 8" manually

Condition: used, Number of sanding units 2 st. sanding width 190 mm Sanding height max. 4-180 mm HESS - GLORIA 2 BELT SINGLE WOOD SANDING MACHINE ----- Manufacturer's description: ----- Compact design designed according to modern principles. Quiet and vibration-free operation thanks to rigid, stable machine housing and special insulation. Work safety device in accordance with the EC Machinery Directive with the "dust-tested" certificate. Iijdpfx Ajv D Rg Dsfieh Offset grinding units with large-dimensioned tension rollers for good heat dissipation and stable sanding belt guidance. Sanding units with forced sanding belt oscillation. 2-point sanding dust extraction directly on the sanding roller. Airborne dust extraction on the large tension rollers. Integrated sanding belt blower for longer service life of the sanding belts. Integrated brushing and finishing device, adjustable via threaded spindle, with large dust extraction. Motorized grinding thickness adjustment of the entire upper unit via precision threaded spindles and linear ball sets on hardened and ground precision shafts with dust and dirt protection. Electronic digital display for workpiece thickness (resolution 0.1 mm). Contact roller and grinding shoe in a balanced ratio to the grinding belt grain load. Hardened and ground grinding rollers. Maintenance-free and wear-free oxide ceramic grinding shoes (DBGM) with excellent sliding properties, good heat dissipation and high dimensional accuracy. Grinding belt tension via pneumatic cylinder. Grinding belt change via pneumatically controlled belt relaxation. Ability to adjust the grinding belt run when changing the belt. Electro-pneumatic pressure monitoring of the compressed air supply with visual fault display. Automatic machine stop triggered when sanding belt breaks and by run-in protection with integrated wood thickness control. Optical display on the control panel. Feed device and proven, calibrated non-slip and non-adhesive transport belts on precisely ground tables and spring-loaded pressure rollers. Cardan shaft drive for even wood transport. Feed speed continuously adjustable. Chip removal adjustment bottom via precision threaded spindle with dimension display via scale ring (resolution 0.1 mm) Ergonomic arrangement of the operating and setting elements on the machine front: sanding unit and brush device at the top, sanding unit and brush device at the bottom, workpiece transport device, sanding thickness setting, operating display, fault display. Control and operating unit with lockable main switch built into the machine housing. All motors electrically protected against overload. Technical data: ----- Grinding belt speed: 24 m/sec. Grinding width: 190 mm Grinding thickness: 4 - 180 mm Shortest workpiece length: 300 mm Feed speed: Continuously adjustable 5 - 25 m/min. Sanding belt dimensions: 200 mm wide 1600 mm long Electrical connection: 400 V, 3/N PE, 50 HZ Grinding units: 2 x 4 kW Feed: 0.75 kW Height adjustment: 0.18 kW Pneumatic connection: R 3/8", 80 NL, 8 bar Extraction air volume: 2 x 2000 - 2500 m3/h 20 - 25 m/sec. Extraction connection nozzle: 2 x 160 mm diameter at the top of the machine housing External dimensions: Length: 1600 mm Width: 1030 mm Height: 1820 mm Height with extraction nozzle: 1930 mm Working...

Condition: excellent (used), Belt sander Make Karnasch Type ALMI AL 100 Iiedpfx Aeuf N Scsfioh with 6 different contact rollers or sanding rollers Diameter : 17,5 - 20 - 22 - 28 - 38 - 48 mm belt width 100 mm length 2000 mm Grinding range for grinding diameter 20 - 76 mm

Condition: used, Year of construction: 2023, Used machine Year of manufacture: 2023 Not used 2-belt machine; 1st belt roller, 2nd belt pad - Usable WORKING WIDTH: 1,100 mm - SANDING BELT LENGTH: 1,120 x 2,150 mm - MAX. WORKPIECE HEIGHT: 160 mm - Steel CALIBRATING ROLLER: 150 mm - SANDING PAD WIDTH: 50 mm - MAIN BELT MOTOR POWER: 11 kW - BELT SPEED: 18/16 m/s - FEED MOTOR POWER: 0.55 kW - Variable speed gearbox for feed conveyor with infinitely adjustable speed: 4–20 m/min - HEIGHT ADJUSTMENT MOTOR: 0.24 kW - Mechanical BELT OSCILLATION "ECO GEAR PATENT SYSTEM" - 1 pc. DRUM BRAKE for belt stop - Swivel ROLL for belt tensioning - 3 pcs. PRESSURE ROLLS with rubber coating - EMERGENCY STOP BAR at feed-in - ELECTRONIC DISPLAY of workpiece thickness - 2 pcs. ROLLER TABLES with 2 rollers each for infeed and outfeed - 1 EXTRACTION CONNECTION with 160 mm diameter - AUTOMATIC TABLE POSITIONING Iisdpfx Afow E Ty Ueish New patented belt oscillation system: 1. Without valves 2. Without photoelectric sensors 3. Not sensitive to dust 4. Energy-saving, environmentally friendly system Since 2008, the machine model with this system has been running continuously without lateral belt deviation! Includes: - Unitek belt motor with 14.7 kW instead of 11 kW (PROMOTOR) - Unitek pneumatic sanding pad with motion control synchronised to feed speed (standard on all NICE models) - Unitek 2 pcs. oscillating, timer-controlled belt cleaning devices - Unitek surcharge for front extendable roller up to max. 500 mm - Unitek surcharge for rear extendable roller up to max. 500 mm - Roller with diameter 180 mm instead of 150 mm Availability: short-term Location: Saxony-Anhalt

Condition: new, The new cylinder brush and sanding machine from Holzprofi Maker can be quickly and easily converted from a sanding machine to a brushing machine in just a few seconds. It is ideal for smaller workshops as it combines two machines in one. Advantages and Features: - Versatile options for surface finishing - Quick and easy changeover from sanding to brushing - Many different brushes available for a wide range of effects and processing possibilities - Infinitely variable feed rate and roller speed for perfect results - Workpiece width up to approx. 1100 mm - Precise adjustment of sanding height for consistent results Technical Data: Sanding width: 560 mm (1120 mm) Sanding height: 3 to 75 mm Roller diameter: Ø132 mm Table dimensions: 592x530 mm Extension table dimensions (2x): 582x245 mm Roller speed: 0 to 1800 rpm Feed speed: 0 to 7.5 m/min Extraction port diameter: 100 mm Main motor power: 1.5 kW Feed motor power: 120 W Voltage: 230 V Dimensions: 1010x1060x1190 mm Weight: 155 kg Ijdswzzivepfx Afijih Optional Accessories: Texturing brush for even and structured surfaces Abrasive flap brush for finishing and surface preparation tasks Steel wire brush for a used-look finish and pronounced grain effect

Condition: good (used), Year of construction: 2010, functionality: fully functional, new container with completely new layer PU-cover with ca. 6mm cover thickness usable volume: 165 liter trough inner measures: 1100mm x 460mm x 525mm empty weight: ca. 850kg motor speed: 1500 rpm sound insulating cabinet extern dimensions: 1900mm x 1250mm x 1550mm Iodpfet Ahqyex Afieih band filter device Seitz

Condition: used, Frame sanding machine LÖWER RSM 280 SX -used- Frame sanding machine sanding pad, oscillation, frame sanding device, feed belt, belt cleaning Iiedpfx Afeu R Tbheieh ----- Technical data ----- Sanding width: 190 mm, max. workpiece thickness: 120 mm, Speeds: 6,11,16 m/min, Motor: 5.5 kW, weight: 550 kg

Condition: used, Oscillation ja_yes ja / nein 0 ja_yes ja/nein 0 ja_yes ja/nein Iodpfx Aewzmuwjfijih tiltable up to ja_yes Motor output 2,2 kW Table dimensions 1000 x 350 mm sanding width 200 mm Weight 300 kg Langzauner LZK 3/2, BB 200 Edge Sander ----- Technical manufacturer's specifications: Table width: 345 mm Table length: 1000 mm Maximum sanding belt width: 200 mm Sanding belt length: 2600 mm Main motor: 3 kW Circular sanding support: Yes Oscillation: Yes Height adjustment: Manual table Swivel sanding belt: Yes Space required length: 1800 mm Space required width: 900 mm ----- Price of the above-mentioned machine upon request! (Technical specifications according to the manufacturer - no guarantee!) All prices quoted are net, plus statutory VAT. No original images available yet; image from a brochure for the same model

Condition: used, Polishing sander Löwer FA 4 S Year of construction 1998 Machine no. 9667 400V, 14.5Amp. 4x 0.37kW motor Iiedpfxjwnh Avj Afijh Working length 3000mm Dimensions: 5000x18050x1600mm (LxWxH), weight 550kg - Documentation available: Yes Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2015, CE mark: yes Serial number: Serie nr: M6xxxx Please contact ATS Norway for more information Please provide reference number upon request: 21323 Specifications : - 2015 model - 10,000 hours approx. - Weight: 23,000 kg - 116 kW. - Sanding bucket - Engcon tiltrotator - S70 Quick Release - Chassis (see pictures) - Radio - Rear view camera - Leadable - Ready for delivery Description : Ijdpjxctinsfx Afioih 2015 model Komatsu pc228 uslc-10 with rotary tilt and sanding bucket for sale. The excavator has run for approximately 10,000 hours. This is ready for delivery.   Hours: 10.000 Own weight: 23000 Total Weight: 23000 CE: Yes Engine hours: 10000 Model: PC228 m/ pusseskuffe og rotortilt!

Condition: used, Repair-needing Wide Belt Sander, Surface Grinding Machine, Sheet Metal Deburring Machine, Deburring Machine with 4 Processing Stations Sanding Unit and Brushing Deburring Unit Manufacturer: BÜTFERING - STEELMASTER Type: Frima-V/413RRTT Machine No.: 76 931 Year of Manufacture: 2002 2x Brushing Deburring Units + 2x Sanding Units Max. working width: 1350 mm Conveyor belt width: 1370 mm (heavily worn on the sides) Working thickness: 0.3 mm to 150 mm Sanding Units Abrasive belt dimensions: 1350 mm x length ?? mm Abrasive belt motor (1): 11 kW (speed 2930 rpm) Abrasive belt motor (2): 12.5 - 16 kW (speed 1470 - 2950 rpm) - Abrasive belt speed (belt 1): only at high speed - Abrasive belt speed (belt 2): 2 speed settings - Pneumatic belt tensioning Brushing Deburring Units with multiple vertical sanding discs and oscillation 2 roller brushes Ø 250 mm Roller width: 900 mm Brush speed: approx. 1440 rpm Deburr brush motor (3): 7.6 - 9.5 kW Deburr brush motor (4): 7.6 - 9.5 kW - Sanding disc speed (3): 2 speed settings - Sanding disc speed (4): 2 speed settings - Oscillating movement of brush rollers via gear motors - 2 separate drive motors, one for each brushing station Conveyor Feed Unit Conveyor motor power: 0.75 kW - Infinitely variable conveyor speed via frequency converter - Motor-driven height adjustment for material thickness 0.3 - 150 mm Power supply: 400 Volt, 50 Hz, 55 kW Machine footprint: Length 300 x Width 270 x Height 210 cm Required space for transport: Length 600 x Width 242 x Height 210 cm Weight: approx. 5.5 tons The machine was operated with wet grinding; belt filtration system integrated in the machine frame Isdsw Ed Uvepfx Afisih The machine is in poor condition, was taken out of production, and stored under tarpaulin for approx. 5 months. Technically, everything still appears to be in reasonable shape, but improper storage has led to some rust formation. The machine requires refurbishment.

Condition: good (used), 8-station tool turret, manually rotatable, for retrofitting 8 x turning tool holders 8 x drilling tool holders Siegfried Volz Machine Tools Rüschebrinkstr. 151-153 DE – 44143 Dortmund - Wambel Iiodpfxjwg Rv Ns Afijh

Condition: good (used), Year of construction: 1996, double-sided top and bottom sanding with sanding shoe and dust brush Isdpfx Asxfl Eaefijih max. sanding width 300 mm max. sanding height 200 mm year of manufacture 1994 with CE mark

Condition: used, Number of sanding units 4 St. sanding width 190 mm Sanding height max. 180 mm Control ja weight 3300 kg Dimensions (L/W/H) 2600x920x1890 mm Dust suction hood 2x180, 2x120 mm Double sided grinding machine Löwer DSM 2004 Double-sided four-band single-wood sanding machine for sanding Solid wood, e.g. Window wood etc. Highly stable top model with innovative details. Suitable for high Continuous load even at higher chip removal rates. - Successively arranged grinding units for rough grinding, fine grinding and finish sanding, each from above and below 1. Belt sanding unit with heavy steel roller 2. Belt sanding unit with rubberised roller and shoe 3.Finish aggregate with fiber brush - Direct driven wheels for slip-free power transmission - Maintenance and wear-free CERMET-coated sanding shoes with very good thermal conductivity and absolute dimensional accuracy - Foreign cooling of the grinding zones for a cooler grinding and higher Sanding belt life - positively driven pneumatically controlled grinding belt oscillation - effective sanding dust extraction directly on the sanding rollers - Dust extraction on the tension rollers - integrated brushing and finishing device with large sanding dust extraction - Motorized grinding thickness adjustment via precision threaded spindles and large dimensioned linear ball bearing sets on hardened and ground precision shafts with dust and dirt protection - Adjustment of chip removal below via precision threaded spindle with dimension display via scale ring (resolution 0,1mm) - Grinding belt tension via pneumatic cylinder with constant clamping pressure - Abrasive belt change with pneumatic belt release in seconds - Adjustment of the grinding belt when changing the belt - Electropneumatic compressed air monitoring - Overflow protection via contact roller for workpieces that are too thick - Workpiece transport via calibrated non-slip and adhesive conveyor belts over heavy, cast tables with finely planed surface and sprung Pinch rollers with fine adjustment - Cardan shaft drive for jerk-free and uniform workpiece transport - Feed gear motor with stepless speed 4-20 m / min - all motors are electrically protected - ergonomically arranged controls - digital strength display (resolution 0.1mm) with modern magnetic tape system Technical specifications: - Sanding belt speed 22 m / s - Sanding belt length 1800mm - Sanding belt width 200mm - Working width 190mm - Abrasive thickness 2-180mm - four brake motors for drive 5.5 kW - Feed motor 1.5 kW - Feed rate 4-20 m / min. - automatic height adjustment 0.37 kW - two brush sets with fiber brushes D 120 x 200mm à 0.37 kW - Exhaust nozzle 2 x 180mm 2 x 120mm - Extraction air speed 20 m / s - Pneumatic connection 6 bar - Working height 870mm - Length (with Softdisc 2740mm) 2600mm - Length with control panel (with Softdisc 3035mm) 2985mm - width 880mm Iisdpfovu Hgbjx Afish - height 1910mm - Weight about 3300 kg - Operating voltage 400 volts, 50 Hz, 3P - CE version Equipped with the following options: - Sanding belt blow 4-band via nozzles directly at the radii of the tensioning rollers within the extraction system arranged, separately switchable - Disc unit for defibering - two grinding disc discs with 200 mm diameter (maximum grinding width 180 mm) - adjustable laterally and in delivery - including frequency converter for stepless speed regulation instead ...

Condition: new, Special offer price for stock goods! Only while stocks last! Price ex stock, plus VAT. Belt sander: Bernardo type/model: MS 75 x 2000 S Condition: new belt dimensions: 75 x 2000 mm belt speed: 29 m/sec. contact wheel Ø x W: 200 / 80 mm surface grinding table: 460 x 75 mm suction connection: 100 mm motor output power S1 100%: 3,0 kW motor input power S6 40%: 4,0 kW Voltage: 400 V length: 1080 mm width: 440 mm height: 1000 mm Weight approx.: 66 kg Features: Good grinding performance due to high belt speed Quick adjustment for horizontal and inclined position Continuous plane grinding surface for optimum grinding of long workpieces Constant belt tension due to spring-loaded tensioning device Universally applicable for sanding edges, surfaces and for cylindrical sanding Including quick tensioning system for fast belt change Easy adjustment of parallel belt run by means of adjusting screw Graphite coating on the face grinding surface increases the sliding properties of the grinding belt Scope of delivery: - Sanding belt K 80 - Hinged protective disc - Grinding and support table - Workpiece stop - Dust extraction nozzle - Separate off button Iisdofnr Aispfx Afish - Base frame

Condition: used, Year of construction: 2002, machine/vehicle number: 02062, The right and left edges are sanded in a single pass. There are 2 brush sanding heads installed on both the left and right sides. Process: 1. The parts are conveyed to the right side in the direction of feed via cross belts that are installed at 90 degrees to the feed direction. 2. The right edge is sanded; 2 sanding brush heads are installed, which are adjustable in height and tilt. 3. The parts are conveyed to the left side in the direction of feed via cross belts that are installed at 90 degrees to the feed direction. 4. The left edge is sanded; 2 sanding brush heads are installed, which are adjustable in height and tilt. Iiedpfxswpwuko Afioh - Manufacturer: Supferfici, Delle Vedove - Part width: approx. 1,400mm - Height of sanding head: 80mm - Sanding height: approx. 60mm - Length: approx. 8,800mm - Working height: 880mm - Year of manufacture: 2002 - A new Siemens S7-1200 will be installed for material control. - Location: in stock

Condition: used, 2-axis linear guide with linear motors - Slide arm pick and place with linear guides for automation Loading unit such as Scara robot, manipulator, handling device, handling system, placement gripper, loading gripper for automation Manufacturer SCHUNK - GEMOTEC - AFAG - LINMOT Type PS01-37x240-M + E1100-MT + T01-/72/420 + EPM 37-780 Year of construction approx. 2005 Horizontal axis with linear motor Gemotec type EPM 37-780 Actuator type: EPM 37x780-M Axis module: LinMot type E1100-MT-HC Horizontal movement: 780 mm Nominal force horizontal: 160 N Horizontal speed: 2.1 m/s Horizontal acceleration: 12.4 m/s² Repeat accuracy: +/- 0.05 mm Horizontal load capacity: max. 7000 g Iedou H R Iwspfx Afieih Horizontal guide column: Ø 20 mm Vertical axis with LinMot linear motor type PS01-37x240-M Actuator type: LM01-23x80/160 Axis module: LinMot type E1100-MT Vertical movement 160 mm Nominal vertical force: 44 N Max force vertical: 203 N Vertical speed: 2.2 m/s Vertical acceleration: 50.4 m/s² Repeat accuracy: +/- 0.05 mm Horizontal guide column: Ø 20 mm Power supply unit LinMot type T01-/72/420 (for motor supply) Input voltage: 3 x 400 V AC 50/60 Hz Output voltage: 72 V DC 420 Watt Base frame Support columns: 4 pieces Ø 55 mm Support column height adjustment: 200 mm (manual height adjustment) Mounting foot: 2 x 175 x 90 mm Control voltage: 24 V DC - Can be moved in two axes - Mounting plate for tool holder 66 x 56 mm - Integrated path measurement - Axis modules with integrated positioning control - Festo pneumatic cylinder as holding brake on the vertical axis - Horizontal axis with 3 external fans - Axis modules configurable via LinMot MPC Configurator 3.2 software Space requirement L x W x H: 1120 x 720 x 740 mm Weight: approx. 65 kg Very good condition

Condition: used, Year of construction: 2002, machine/vehicle number: 02062, The right and left edges are sanded in a single pass. There are 2 brush sanding heads installed on both the left and right sides. Process: 1. The parts are conveyed to the right side in the direction of feed via cross belts that are installed at 90 degrees to the feed direction. 2. The right edge is sanded; 2 sanding brush heads are installed, which are adjustable in height and tilt. Iedpfx Aowpwuqsfieih 3. The parts are conveyed to the left side in the direction of feed via cross belts that are installed at 90 degrees to the feed direction. 4. The left edge is sanded; 2 sanding brush heads are installed, which are adjustable in height and tilt. - Manufacturer: Supferfici, Delle Vedove - Part width: approx. 1,400mm - Height of sanding head: 80mm - Sanding height: approx. 60mm - Length: approx. 8,800mm - Working height: 880mm - Year of manufacture: 2002 - A new Siemens S7-1200 will be installed for material control. - Location: in stock

Condition: used, Vertical grinding machine, surface grinding machine DORMAC / DORIA type Perseo Cup grinding machine No. 786 Year of manufacture 1987 Sanding area 500 x 250 mm Magnet 400 x 150 mm Grinding height grinding wheel - magnet approx. 190 mm Grinding height grinding wheel - clamping surface table approx. 235 mm Grinding wheel diameter 175 mm Table longitudinal movement approx. 600 mm Ijdpfx Asvkgvhofioih Grinding wheel speed approx. 2800 rpm Motor power approx. 2.2 kW Mains connection 380 Volt, 50 Hz - Manual depth adjustment via handwheel, travel per handwheel rotation, Z-axis 2.5 mm = 0.01 mm per graduation mark - handwheel on the right of the spindle housing, fine adjustment via knurled wheel on the handwheel - Manual transverse adjustment via handwheel, travel per handwheel revolution, Y-axis 2 mm = 0.01 mm per graduation mark - Hydraulic longitudinal table movement - mechanical magnet WAGNER, type 0112N-15/40-4 400 x 150 mm, height 45 mm - Wet grinding unit with settling filter opposite - 2 grinding wheels Ø 175 mm - 1 grinding wheel holder - 1 balancing device for the grinding wheels Space requirement L x W x H 1500 x 1100 x 1800 mm Weight 570 kg good condition

Condition: used, Disc sander with spindle sander KURT EHEMANN type V K8 Combined drum sanding machine - double sanding machine, cylindrical rod sanding machine Machine no. No. 6812420 Year of construction 1968 Sanding disc diameter 800 mm Table support on sanding disc 900 x 300 mm Sanding disc speed 940 rpm Table height of sanding disc 900 mm Spindle sanding unit with sanding sleeve Ø 50 mm Table support for spindle sanding unit Ø 500 mm Table height spindle sanding unit 1000 mm Spindle sanding unit speed 1410 / 2420 rpm pole-changing Motor power sanding disc 3 kW Iiodpfx Asrk U Edofioh Motor power spindle grinding unit 1.1 / 1.6 kW Mains connection 380 Volt, 50 Hz - inclinable sanding table, 30° downwards/ 15° upwards - the entire table can be swiveled away from the plate for changing sandpaper - Spindle sanding unit with clockwise/anticlockwise rotation (1410 rpm for clockwise rotation, 2420 rpm for anticlockwise rotation) - Spindle sanding unit with oscillating stroke movement 10 mm - Height-adjustable grinding spindle in the table - Spindle sanding unit with inclinable rotary table, inclinable by approx. 30° - Rotary table with removable segment inserts Ø 54 / 84 / 308 mm - Pipe connection for extraction system, rectangular 100 x 170 mm Space requirement L x W x H 1500 x 1100 x 1400 mm Weight 550 kg Very good condition