Used Shoe for sale (336)

Condition: good (used), Fixators, leveling units, leveling elements, machine foot, machine feet, leveling shoes, machine foundation, leveling shoe, wedge shoe, machine support, leveling foot -Fixators: for machine tools and systems -Minimum height: 75 mm -Max. height: 95 mm -Price: per piece Rsdefdd Avepfx Ahvsbw -Quantity: 4 pieces -Dimensions: 230/180/H80 mm -Weight: 12.3 kg/piece

Condition: used, Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Rbjdpfx Ahot Tqy Eovjw Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Condition: excellent (used), Year of construction: 2008, Working width: 1100 mm Workpiece thickness: 3 – 160 mm Abrasive belt dimensions: 1,120 x 1,900 mm Variable feed speed: 2.6 - 13 m/min Feed motor output: 1.10 kW, 400 V, 50 Hz Extraction port diameter: 2 x 160 mm Compressed air supply: 6 bar Dimensions (L x W x H): 1705 x 1545 x 1905 mm 1st unit: Steel contact roller, diameter 160 mm Motor output: 15 kW, 400 V, 50 Hz 2nd unit: Combination unit with rubber-coated contact roller (Sh 65), rigid sanding shoe Motor output: 11 kW, 400 V, 50 Hz Abrasive belt cleaning via compressed air Rodpeychqzefx Ahvsbw 3rd unit: Cleaning brush Multi-function display Multi-function lever (conveyor belt, workpiece thickness adjustment) Electronic belt oscillation Pneumatic conveyor carpet oscillation Motorized workpiece thickness adjustment with LED display in 0.1 mm increments Units with emergency braking system Emergency stop button at infeed & outfeed Motor protection switch Roller table extension at infeed with 2 loose rollers Automatic star/delta start Complete documentation Note for used machines: • Specifications and prior sale subject to change. • Stated prices are ex works – loaded free of charge! • The machine has been cleaned and functionally tested. • All machines are sold as seen, without any warranty or guarantee. Buyers are welcome to inspect the machine on site. • Special agreements are only possible in written form. (We only respond to inquiries providing your address and telephone number!)

Condition: as good as new (ex-display), functionality: fully functional, grinding height: 200 mm, power: 11.03 kW (15.00 HP), grinding belt speed: 18,000 mm/s, grinding belt length: 2,620 mm, grinding belt width: 1,370 mm, input frequency: 50 Hz, input voltage: 400 V, Additional technical data Feed speed: 2.8 - 20 m/min The new Format4 findustry wide belt sanders impress in industrial applications primarily through their individually configurable assembly of units. Tailored specifically to the application and field of use, the machine can be equipped with two, three, or four units. A high degree of customization guarantees that all requirements in terms of surface finish and processing efficiency are met. Maximum operating comfort in industrial applications The clearly structured touchscreen control panel is intuitive to operate. All machine functions are clearly displayed graphically on the digital display. The pass-through thickness can be set directly from the control panel to a tenth of a millimeter at the touch of a button. Automatic thickness measurement simplifies the adjustment of the machine to the desired workpiece thickness. The workpiece can be measured without additional measuring devices, and its thickness is then transmitted directly to the machine "wirelessly." The fixed infeed table height of 900 mm allows for easy and fatigue-free operation, while a vacuum table, roller table extensions on both infeed and outfeed sides, as well as optional pressure shoes on the sanding units, ensure maximum comfort and optimal processing conditions for workpieces of any size. Optional equipment 10E LACQUER – Cross sanding unit ESC in place of 1st contact roller 20A 2nd contact roller unit 22 2nd sanding roller in 85° Shore 30E LACQUER – Superfinish unit ESC in place of 3rd contact roller 39 Switch contact for slide control (price/piece) *6 51 Soft start for 15kW (20HP motor) 59B Control unit with 15" color touchscreen display 63 Scotch-Brite brushing device at the machine outfeed 71 Oscillating cleaning blower for workpiece and conveyor belt 72 Ionizing bar at the machine outfeed 73 Vacuum table with 4kW (5.5 HP) blower 74 Inverter for vacuum blower for vacuum adjustment 83 Sanding height 200mm instead of 170mm 84 Optimized control software for special processing Rbjdpfx Ahsxtpydsvow 87 ESC workpiece detection sensor with 50 segments 201 2nd motor with 15kW power output Additional information Workpiece height: 3 - 170 mm Constant infeed height - fixed table: 900 mm Grooved sanding roller: Ø 250 mm Including delivery and installation in post code areas 71, 72, 73, 77, 78, 79, 86, 87, 88, 89

Condition: as good as new (ex-display), functionality: fully functional, grinding width: 1,100 mm, grinding height: 170 mm, power: 14.71 kW (20.00 HP), grinding belt length: 1,900 mm, grinding belt width: 1,100 mm, input frequency: 50 Hz, input voltage: 400 V, Further technical data: Sanding height: 3 - 170 mm Extraction connection: 200 / 120 mm Standard equipment: - Star-delta starter - CE safety standards - Electrically controlled height adjustment of the feed table including fine adjustment from the control panel - Stepless feed speed from 2.5-18 m/min adjustable via inverter from the control panel - Hand guard and workpiece thickness safety device - Endless belt conveyor with honeycomb structure - Automatic feed belt centering - Control unit with 7" touch color display - 1st unit with rubberized, profiled contact roller, 85° Shore hardness - 2nd unit (sanding pad unit): The electro-pneumatic segmented sanding shoe with 25 mm segment width enables the independent processing of multiple workpieces for perfect veneer sanding. The standard time-controlled cleaning blower ensures maximum sanding belt service life, especially for lacquer sanding or very fine grit. - Digital grit compensation - Mechanically preloaded rubber pressure rollers - Sanding belt oscillation, electronic-pneumatic - Electronic sanding belt run-off protection Rbodovf D S Aopfx Ahvsw - 1 motor with 15 kW (20 HP) including automatic star-delta start - Min. air pressure (bar): 6 Optional equipment: - Vacuum table with integrated blower in the machine frame - 15 kW (20 HP) motor including variable cutting speed from 2.4 to 19 m/sec - Double-sided roller table extension, 200 mm - Scotch Brite brush unit at the machine outfeed, D=150 mm - Switching contact for slide valve control; shut-off valves for extraction can thus be actuated. Including delivery and installation in postcode areas 71, 72, 73, 77, 78, 79, 86, 87, 88, 89

Condition: used, Year of construction: 2025, _____Year of manufacture 2025 14,000 litres 4,000-litre pump Rsdpfx Aheyr U Ifevjbw Suction connection right/left Suction arm right Tyres 750/60R 30.5 Hydraulic drawbar adjustment Front cutter Electric forced steering Filling automation with shut-off function Signo Smart control Bomech with two cutters 6-inch suction arm with 8-inch ball coupling Half-width shut-off via slide valve Bomech trailing shoe distributor Speedy Small 12 m Vehicle has not been registered, Storage location: none

Condition: new, pressure 220 t chamfer lenght 4100 mm distance between columns 3600 mm column arm 410 mm ram stroke speed 150 mm/sec work speed 10.0 mm/sec return speed 140 mm/sec work stroke 265 mm dayligth 480 mm table height 900 mm table width 110 mm oil volume 300 ltr. voltage 400 Volt Rbodpfxoynnk Ee Ahvow total power requirement 18.5 kW weight 15000 kg range L-W-H 5000 x 2400 x 2850 mm ALPMAC Manufacturer Video: ?v=_FxXyPAcxlE ?v=YfkX9RwWv_0 ALPMAC Product Video Model B: ?v=lmT1tfy43WE ----- MODEL SERIES B175-3100 - CNC electro-hydraulic press brake with: * increased installation height * increased cylinder stroke * increased throat depth ----- ! MADE FROM CERTIFIED QUALITY STEEL (ST 37-42-52) ! HIGH-PERFORMANCE HYDRAULIC COMPONENTS (HAWE GERMANY) ! HIGH RUNNING QUIET DUE TO LOWER OPERATING PRESSURE (50-60 dB) ! INDUCTION-HARDENED & CHROME-PLATED CYLINDER PISTONS FOR CONTINUOUS USE ! ALUMINUM CAST REAR STOP COMPONENTS ! REAR STOP WITH POWERFUL DRIVE MOTOR (1.0 kW) ! MACHINE TABLE MADE OF ROBUST & DURABLE STEEL (C45) GREEN ECO Technology: Lower consumption. More quiet. Full control. ! Peak performance with minimal energy consumption ! Maximum power at minimal cost ! Maximum performance when it's really needed ! Main motor is only activated by the foot pedal ! No energy wasted in standby mode ! Controlled start-up process Equipment: - CNC electro-hydraulic press brake - DELEM CNC control model DA-66T- graphics/touchscreen * 2D graphic touchscreen programming operation * 3D display in simulation and production * 17" high-resolution color TFT screen * Bending sequence calculation * Product programming and display in actual size * USB interface - CNC controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning - CNC electro-motorized backgauge (X-axis) * on ball screws * Travel: max. 750 mm * X-axis travel speed: 350 mm/s * with 2x CNC-controlled backgauge fingers - CNC electro-motorized height adjustment (R-axis) * Travel: max. 250 mm * R-axis travel speed: 300 mm/s - CNC electro-motorized table crowning - ROLLERI Rehfuß upper tool "PS 135.85-R08", System "A" * including quick-change clamping * including crowning device in the tool holder - ROLLERI split universal die block "M 460 R" * including 1x die shoe "C 1050-R" - Rear safety device: light barrier - HAWE hydraulic components - FIESSLER AKAS laser safety device in front of the machine (incl. FPSC) - 2x front support arms with sliding system * easily and keylessly height-adjustable - FIESSLER freely movable double foot control - CE marking / Declaration of Conformity

Condition: new, pressure 175 t chamfer lenght 3100 mm distance between columns 2600 mm column arm 410 mm ram stroke speed 160 mm/sec Rjdsxaa Eqjpfx Ahvobw work speed 10.0 mm/sec return speed 120 mm/sec work stroke 265 mm dayligth 480 mm table height 900 mm table width 90.0 mm oil volume 230 ltr. voltage 400 Volt total power requirement 18.5 kW weight 10500 kg range L-W-H 4100 x 2000 x 2820 mm ALPMAC Manufacturer Video: ?v=_FxXyPAcxlE ?v=YfkX9RwWv_0 ALPMAC Product Video Model B: ?v=lmT1tfy43WE ----- MODEL SERIES B175-3100 - CNC electro-hydraulic press brake with: * increased installation height * increased cylinder stroke * increased throat depth ----- ! MADE FROM CERTIFIED QUALITY STEEL (ST 37-42-52) ! HIGH-PERFORMANCE HYDRAULIC COMPONENTS (HAWE GERMANY) ! HIGH RUNNING QUIET DUE TO LOWER OPERATING PRESSURE (50-60 dB) ! INDUCTION-HARDENED & CHROME-PLATED CYLINDER PISTONS FOR CONTINUOUS USE ! ALUMINUM CAST REAR STOP COMPONENTS ! REAR STOP WITH POWERFUL DRIVE MOTOR (1.0 kW) ! MACHINE TABLE MADE OF ROBUST & DURABLE STEEL (C45) GREEN ECO Technology: Lower consumption. More quiet. Full control. ! Peak performance with minimal energy consumption ! Maximum power at minimal cost ! Maximum performance when it's really needed ! Main motor is only activated by the foot pedal ! No energy wasted in standby mode ! Controlled start-up process Equipment: - CNC electro-hydraulic press brake - DELEM CNC control model "DA-58T" with graphics/touchscreen * 2D graphical programming * 15" high-resolution color TFT screen * Bending sequence calculation * Product programming and real-size display * USB interface - CNC controlled axes: Y1 - Y2 - X - R - crowning - CNC electro-motorized backgauge (X-axis) * on ball screws * Travel: max. 750 mm * X-axis travel speed: 350 mm/s * with 2x manually adjustable backgauge fingers - CNC electro-motorized height adjustment (R-axis) * Travel: max. 250 mm * R-axis travel speed: 300 mm/s - CNC electro-motorized table crowning - ROLLERI Rehfuß upper tool "PS 135.85-R08", System "A" * including quick-change clamping * including crowning device in the tool holder - ROLLERI split universal die block "M 460 R" * including 1x die shoe "C 1050-R" - Rear safety device: light barrier - HAWE hydraulic components - FIESSLER AKAS laser safety device in front of the machine (incl. FPSC) - 2x front support arms with sliding system * easily and keylessly height-adjustable - FIESSLER freely movable double foot control - CE marking / Declaration of Conformity

Condition: used, Kündig Topiq-1100 Swiss quality product Constant table machine / automatic head adjustment Wide-belt calibrating and fine sanding machine Combination unit with contact roller and sanding pad unit featuring electronically controlled segmented sanding shoe Belt drive motor power approx. 11 kW Contact roller height steplessly adjustable according to grit scale Rsdoyngxhjpfx Ahvjbw Working width 1100 mm Feed speed 3 - 15 m/min, infinitely adjustable Automatic workpiece thickness adjustment ENORMATIC quick setup Program selection via SmartSelect control Machine is WORKSHOP-REFURBISHED and in VERY GOOD CONDITION Available ex-stock Lieboch

Condition: used, functionality: fully functional, input voltage: 400 V, type of input current: three-phase, cutting height (max.): 120 mm, cutting width (max.): 300 mm, saw blade diameter: 350 mm, height adjustment type: mechanical, saw blade bore: 70 mm, actuation type: electric, - Operating manual, DTR - Italian production TECHNICAL SPECIFICATIONS: - Track width: 300 mm - Cutting height: 120 mm - Max. blade diameter: 350 mm - Motor power: 30 kW - Table width: 750 mm - Min. workpiece length: 600 mm - Feed speed adjustable via gearmotor - Three rows of anti-kickback pawls - Possibility to mount a board – shoe - Spindle diameter: 50 mm - Sleeve diameter: 70 mm Rjdpfx Ahoym Ag Sjvobw - Sleeve equipped with spacers - Automatic central lubrication - Four upper feed rollers - Extraction port diameter: 200 mm - Machine dimensions (L/W/H): 155 / 165 / 160 cm - Weight: 1800 kg

Condition: new, functionality: fully functional, power: 14.6 kW (19.85 HP), gearing type: hydrostat, fuel type: diesel, fuel tank capacity: 1 l, color: yellow, operation weight: 3,000 kg, maximum load weight: 3,000 kg, lifting height: 4,010 mm, tire condition: 100 %, drive condition: 100 %, chain condition: 100 %, number of seats: 1, first registration: 01/2026, emission class: euro5, Year of construction: 2026, operating hours: 1 h, machine/vehicle number: 1, Equipment: additional headlights, air conditioning, cabin, Excavators GT3000 The GT3000 excavator is a modern crawler machine designed for earthmoving operations that require an extensive working range, high breakout force, and a stable construction. Thanks to its compact dimensions and robust undercarriage, the machine is ideal for foundation work, installation jobs, municipal projects, and tasks in areas with limited maneuvering space. Engine The machine is equipped with a reliable Yanmar 3TNV80F engine delivering a rated power of 14.6 kW. This engine ensures stable and fuel-efficient performance. Working Range The excavator is fitted with a bucket offering a capacity of 0.09 m³ and a width of 460 mm. The bucket breakout force of 17.6 kN enables efficient digging, even in tougher soil conditions. A maximum digging depth of 2810 mm and a maximum reach of 4375 mm provide a large operational area, reducing the need for frequent repositioning. A maximum digging height of 4510 mm and a dumping height of 2760 mm allow easy loading of material onto transport vehicles. Dimensions and Stability The overall dimensions of the machine are 4010 mm in length, 1540 mm in width, and 2360 mm in height up to the top of the cab (1380 mm to the top of the boom). The track contact length with the ground of 1530 mm and a track gauge of 1510 mm ensure stability during operation. The 250 mm wide track shoes and low ground pressure of 26.7 kPa allow safe operation on less compacted surfaces. Mobility and Maneuverability A rear swing radius of 710 mm allows comfortable operation in confined spaces. The swing frame width of 1350 mm and a counterweight clearance of 485 mm, as well as a minimum ground clearance of 255 mm, enable smooth movement over uneven terrain. The sturdy undercarriage with a track length of 1895 mm guarantees good traction and safe operation. Technical specifications Operating weight: 3000 kg Engine: Yanmar 3TNV80F Number of cylinders: 3 Rated power: 14.6 kW Bucket capacity: 0.09 m³ Bucket width: 460 mm Bucket breakout force: 17.6 kN Swing arm: Present Joystick: Present Swing speed: 13 rpm Max. digging height: 4510 mm Max. dumping height: 2760 mm Max. digging depth: 2810 mm Max. reach: 4375 mm Rear swing radius: 710 mm Track contact length with ground: 1530 mm Total track length: 1895 mm Track gauge: 1510 mm Track shoe width: 250 mm Swing frame width: 1350 mm Ground pressure: 26.7 kPa Total length: 4010 mm Total width: 1540 mm Rsdpfx Aoymtfxehvjbw Total height (to top of boom): 1380 mm Total height (to top of cab): 2360 mm Counterweight clearance: 485 mm Minimum ground clearance: 255 mm

Condition: new, mileage: 1 km, power: 50 kW (67.98 HP), gearing type: automatic, fuel type: diesel, overall weight: 2,850 kg, lifting power: 1,000 kg/m, drive condition: 100 %, chain condition: 100 %, Year of construction: 2024, Equipment: additional headlights, cabin, GG010 The new Günter Grossmann GG010 LOADER The Günter Grossmann GG08 loader (1000 kg payload) is brand new. Günter Grossmann is a high quality machine made for a European company. The charger is very strong and can work under all conditions. The charger is very nice. The control panel is very nice and clear. The cabin is soundproof, insulated, equipped with heating, very comfortable and beautifully glazed, allowing safe and comfortable work. The machine has a very durable construction. The machine is equipped with a quick coupler, which makes it possible to change accessories quickly without leaving the cab. Additional equipment: 4 in 1 bucket, crocodile grab, crocodile grab for trees, straw or silage. Price 14,550 euros (excl. VAT) Included as standard GG010 loader + bucket + pallet fork + quick coupler Model 1000 kg SPECIFICATIONS Rbsdpsiit Erofx Ahvjw Model: GG10 Brand: Günter Grossmann Engine: Changchai 390 Engine: In-line setup, water-cooled four-stroke diesel engine Engine power: 50 hp Speed: 2200 r/min (rpm) Steering system: Cycloid full hydraulic steering system: BZZ-80 System Pressure: 10MPa Service brake: Hydraulic four-wheel brake with staggered shoes Parking brake: manual Tire: 10-16.5 Wheelbase: 2170mm Track: 1285 mm MEASUREMENTS Total length (bucket at ground position): 41--mm Ground to top of cab: 2530 mm Total width: 1600 mm WORKING RANGE Bucket capacity: 0.5 m3 Bucket width: 1600 mm Max. Height Breakout Force: 28KN Rated load: 1000 kg Operating weight: 2850 kg Drive means: four-wheel drive Min turning radius: 4600 mm ACCESSORIES Bucket 4 w 1: 1050 Eur Pitchfork: 1050 Eur Pallet fork: 650 Eur Quick coupler: 600 Eur Drill: 1400 Eur Bale clamp: 950 Eur Grass clip: 950 Eur Lawnmower: 1450 Eur Snowplow: 1375 Eur

Condition: new, functionality: fully functional, power: 14.7 kW (19.99 HP), gearing type: hydrostat, fuel type: diesel, color: yellow, overall weight: 2,420 kg, empty load weight: 2,420 kg, operation weight: 2,420 kg, lifting height: 4,300 mm, tire condition: 100 %, drive condition: 100 %, chain condition: 100 %, number of seats: 1, emission class: euro5, Year of construction: 2026, Equipment: additional headlights, adjustable chassis, air conditioning, cabin, hydraulics, Excavators GT3000 The GT3000 excavator is a modern tracked machine designed for earthmoving operations requiring excellent working range, high digging force, and a stable construction. Thanks to its compact dimensions and robust undercarriage, the machine is ideal for foundation works, installation tasks, municipal projects, and operations in areas with limited maneuvering space. Engine The machine is equipped with a reliable Yanmar 3TNV80F engine delivering a rated power of 14.6 kW. This engine ensures stable and fuel-efficient performance. Working Range The excavator features a 0.09 m³ bucket with a width of 460 mm. The bucket digging force of 17.6 kN allows for efficient excavation, even in tougher soils. The maximum digging depth of 2810 mm and a maximum reach of 4375 mm provide a wide working range without the need for frequent repositioning. A digging height of up to 4510 mm and a dumping height of 2760 mm enable easy loading of materials onto transport vehicles. Rbodpfxoymtdno Ahvew Dimensions and Stability The overall machine dimensions are 4010 mm in length, 1540 mm in width, and 2360 mm in height to the top of the cab (1380 mm to the top of the boom). The track contact length of 1530 mm and a track width of 1510 mm ensure stability during operation. Track shoes with a width of 250 mm and a low ground pressure of 26.7 kPa allow safe working on less solid surfaces. Mobility and Maneuverability A tail swing radius of 710 mm allows comfortable operation in confined spaces. The swing frame width of 1350 mm and counterweight clearance of 485 mm, along with a minimum ground clearance of 255 mm, ensure smooth movement over uneven terrain. The robust undercarriage with a track length of 1895 mm provides excellent traction and safe operation. Technical Specifications Operating weight: 2420 kg Engine type: Yanmar 3TNV80F Number of cylinders: 3 Rated power: 14.7 kW Rated engine speed: 2200 rpm Max. hydraulic system pressure: 18 MPa Max. gradeability: 30° Ground pressure: 35 kPa Max. travel speed: 2.5–3.5 km/h Max. tractive force: 16 kN Max. slewing speed: 11 rpm Max. digging force: 15 kN Max. digging height: 4300 mm Max. dumping height: 2530 mm Max. digging depth: 2550 mm Max. digging radius: 4150 mm Digging radius at max. height: 2700 mm Minimum radius: 1800 mm Boom length: 1950 mm Arm length: 950 mm Bucket width: 450 mm Overall length: 3950 mm Overall width: 1400 mm Overall height: 2300 mm Minimum turning radius: 790 mm Track length on ground: 1870 mm Track width: 250 mm Ground clearance: 250 mm Platform width: 1330 mm Engine hood height: 1350 mm Platform height above ground: 480 mm

Condition: new, Year of construction: 2026, Pfaff 335 Industrial Sewing Machine – Cylinder Arm For sale: Pfaff 335 industrial sewing machine. A professional cylinder arm sewing machine, ideal for sewing items with curved or hard-to-reach areas. The Pfaff 335 is well known for its precision, reliability and strong feeding system, making it perfect for working with leather, artificial leather, canvas and other durable materials. This type of machine is widely used for making and repairing bags, shoes, upholstery and other leather goods. Specifications / features: Brand: Pfaff Model: 335 Industrial cylinder arm sewing machine Suitable for leather, artificial leather and similar materials Smooth and precise stitching Rbedpfxoyriyvo Ahvsw Strong and reliable transport system Complete with sturdy table and motor Condition: Machine is in good working condition and well maintained. Included: Original table Motor Possible extra bobbins / accessories Perfect for leatherwork, bag making, upholstery and shoe repair.

Condition: new, Year of construction: 2026, ürkopp Adler 069 Industrial Sewing Machine – Heavy Duty Leather Machine For sale: Dürkopp Adler 069 industrial sewing machine. A very strong and reliable machine, perfect for sewing leather, artificial leather, canvas and other heavy materials. Dürkopp Adler machines are known for their high industrial quality, power and durability. The 069 is widely used for making and repairing bags, belts, upholstery, shoes and other leather products. Specifications / features: Brand: Dürkopp Adler Model: 069 Industrial sewing machine Suitable for heavy materials such as leather and canvas Strong feeding system for even and clean stitches Complete with sturdy table and motor Condition: Machine is in good working condition and well maintained. Rbodpfx Ajyrivqjhvew Included: Original table Motor Possible extra bobbins / accessories Perfect for leatherwork, upholstery, shoe repair and bag making.

Condition: reconditioned (used), Year of construction: 2001, Universal milling & drilling machine DECKEL MAHO DMU 50 M With control Heidenhain TNC 320 Year of construction: 2001 Travels: X 500 Y 400 Z 400 Speed range: 20 - 4,500 rpm infinitely variable Rodjuw Sd Iepfx Ahvobw With the following accessories: Manual swivel rotary table with digital display for C + B axis 700 mm x 500 mm clamping surface Electronic handwheel for X , Y , Z axis Splash guard cabin Machine light 4 pcs. Height-adjustable machine shoes Coolant device Operating instructions

Condition: reconditioned (used), CNC vertical machining center "DECKEL MAHO DMC 635 eco" With path control Siemens 810 Powerline Year of construction: 2010 Travels: X 635 Y 510 Z 460 Speed range: 20 - 8,000 rpm infinitely variable With the following accessories: Rigid angled table 790 mm x 560 mm clamping surface Vertical tool changer with 20 magazine positions Rbodpfx Aheuqmvksvow Electronic handwheel Heidenhain TT 140 tool length measuring system Fully protected cabin with sliding doors and interior lighting Coolant device Signal light 4 colors Chip conveyor Chip flushing gun 3 pcs. Height-adjustable machine shoes Operating instructions

Condition: reconditioned (used), Year of construction: 2002, CNC vertical machining center MIKRON VCP 800 W With path control Heidenhain iTNC 530 Year of construction: 2002 Travels: X 800 Y 650 Z 500 Speed range: 0 - 20,000 rpm infinitely variable With the following accessories: Redpfx Ahsviq U Eevsbw Rigid angular table 900 mm x 600 mm clamping surface Vertical tool changer with 30 magazine slots (HSK 63) Fully protected cabin with sliding doors and interior lighting Electronic handwheel Tool measurement in the work area ( BLUM laser ) 3 D measuring probe infrared Renishaw Chip conveyor Coolant device 4 pcs. Height-adjustable machine shoes Operating instructions

Condition: refurbished (used), Year of construction: 1996, Universal tool milling machine KUNZMANN WF 4/3 With 3 axes Heidenhain digital readout Rbsdjq Ulucepfx Ahvow Year of construction: 1996 Travels: X 400 Y 320 Z 400 Speed range: 40 - 2550 rpm With the following accessories: Rigid angle table 800 mm x 360 mm clamping surface Mechanical handwheels for X , Y , Z axis Hydraulic tool clamping Automatic central lubrication pump for X , Y , Z axis Machine light 4-piece machine shoes Coolant device Operating instructions THE MACHINE WAS ONLY USED FOR APPRENTICE TRAINING !!! THE MACHINE IS IN GOOD CONDITION !!!

Condition: used, Decoiler, pivoting decoiler GSW SCHWABE Type LHD 50/800 Sond Rbodpjhubgwjfx Ahvew Double decoiler, double mandrel decoiler Factory No.: 5775 Year of manufacture: approx. 1995 Coil weight: 50 kg per side Coil width: max. 130 mm Coil inner diameter: 155 - 445 mm Coil outer diameter: 850 mm Support discs: Ø 850 mm Start rings: Ø 850 mm Distance from center of mandrel shaft to base: 980 mm - Manual 180° rotatable decoiler assembly with locking positions - Central expansion via rotation lever adjustment - Mechanical disc brake, adjustable brake shoes with knurled screw Required space (L x W x H): 1000 x 850 x 1500 mm Weight: 190 kg Good condition

Condition: new, pressure 175 t chamfer lenght 3100 mm distance between columns 2600 mm column arm 410 mm ram stroke speed 180 mm/sec work speed 10.0 mm/sec return speed 135 mm/sec work stroke 275 mm dayligth 550 mm table height 900 mm Rbsdpfexaax Rex Ahvsw table width 90.0 mm oil volume 200 ltr. voltage 400 Volt total power requirement 15.0 kW weight 9450 kg range L-W-H 4250 x 2150 x 2800 mm ----- Press brake with special equipment * increased installation height * increased cylinder stroke * as well as increased bending beam speeds ----- Furnishing: - DELEM CNC control model DA-58T graphic/touch screen * 2D graphical programming * 15" TFT color screen with high resolution * Bending sequence calculation * Product programming and real size display * USB interface - Motorized backgauge with R-axis, on ball screws - X = 800 mm R = 250 mm with 2 stop fingers - controlled axes Y1 - Y2 - X - R - C (crowning) - electr. Crowning controlled by CNC - Deer foot upper tool with PS 135.85-R08, system "A" with quick-change clamp - additional crowning device in the tool holder of the upper tool - 4V universal die block M 460 R with die shoe 60 mm mount - BOSCH/HOERBIGER hydr. components - SIEMENS electrical system - LEUZE light barrier behind the machine - FIESSLER AKAS laser with FPSC protection device v.d. machine - Swiveling control panel, mounted on the left - 2x front support arms "Sliding-System", with T-slot and cam - 1x double foot control - CE mark / declaration of conformity - Operating manual: Machine and control in German - Safety manual : press brakes

Condition: used, No. 3176 Automatic planer and moulder WEINIG Hydromat 1000 Used, year of construction 2007 6 spindles: bottom-right-left-top-top-bottom Electronic feed 6 - 60 m/min Working width 80 - 150 mm Working height 23 - 65 mm Finished slat widths 4 - 15 mm Max. Max. number of slats 16 pieces Slat lengths 400 - 4000 mm 1st spindle horizontal at the bottom Brake motor 11 kW, 6000 rpm Spindle diameter 45 mm Tool flight circle 125 - 180 mm 2nd spindle vertical right Brake motor 7.5 kW, 6000 rpm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment travel 80 mm 3. spindle vertical left 7.5 kW, 6000 rpm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment travel 80 mm Pressure shoe in front of the spindle, swiveling away, pneumatic roller contact pressure 4. spindle horizontal top 15 kW, 6000 rpm, diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment path 45 mm Split pressure shoe in front of upper spindle, adjustable and swiveling away, pneumatic 5. horizontal top spindle as saw spindle Brake motor 37 kW, 5000 rpm Diameter 45 mm Axial adjustment travel reduced to 25 mm Tool flight circle 112 - 250 mm Max. Sawing depth 35 mm Axial adjustment path 45 mm Split pressure shoe in front of upper spindle, adjustable and swiveling away, pneumatic 6. horizontal spindle at the bottom as saw spindle Brake motor 30 kW, 5000 rpm Axial adjustment travel reduced to 25 mm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Sawing depth 35 mm Axial adjustment path 45 mm All moulder spindles with high-performance bearings Electronic feed 7.5 kW Adjustment travel of the feed rollers compared to the left-hand spindle, axial 35 mm Shorter roller distance compared to the right-hand spindles Running meter counter, electric, with 2 counters Short infeed table (1.2 m) with 2 driven rollers above the table 1 driven, toothed roller in the table, lateral pressure roller Automatic waxilite pump / lubricant pump Machine with 4-roller extension, pendulum shafts extended to 200 mm 2 driven, toothed rollers in the outfeed table 2 driven, toothed rollers in the machine table Pressure beam before and after upper spindle with mechanical digital display DigiSet (digital double display) for left and top spindles Electrical height adjustment of the upper spindles and the feed Machine already dismantled and stored Sale on behalf of customer, ex location near South Tyrol, without transportation and assembly Subject to errors in the description and price Transportation and loading by us optionally possible To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Images and videos serve as examples and do not represent the actual scope of delivery Rodpfxou Agh So Ahvobw Terms of payment: Prices plus VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: new, Year of construction: 2024, gearing type: other, driver cabin: other, Additional Information * 3-metre clearing width * suitable for mounting plate size 5 * hydraulic lifting device * LED plough lighting and marker lights * right-hand raised ploughshare * scraper bar including shock absorbers * steel skid shoes Other Information: * Trade-in and purchase of vehicles and machinery possible. * Sale price excludes transport and delivery. * No liability for printing and typographical errors. * Subject to errors, modifications, and prior sale. * Offer is non-binding. * Photos may vary. Price applies to current condition. Rbsdpfx Ahoypav Nevow * All information provided without guarantee.

Year of construction: 2022, condition: new, 1 x Niro-Tech SHM2 pass-through hygiene station, comprising of boot-wash, hand sanitising/disinfecting station and turnstile. The boot-wash features traditional rotating brushes which clean and disinfect work shoe / boot bottoms with automatic dispensation of disinfection / sanitising fluid. The hand-sanitising station automatically doses sanitising solution when hands are inserted in the specially designed sockets. Can be manufactured so as to run Right – Left or Left – Right depending on your factory requirements. Rsdpfshr Rqlox Ahvebw Dimensions – 1620mm wide x 1080mm long x 1400mm high. Electricity – 400v, 50hz, 3 phase. Manufactured in AISI 304 stainless steel. Brushes can be chosen in blue, red or white colours.

Condition: new, Bernardo surface grinding machine BSG 2040 PLC Technical specifications Table clamping surface 200 x 500 mm Rbodpfx Ahjgd Ia Sovsw T-slots number / width 1 / 14 mm Electro-magnetic clamping plate 200 x 460 mm Max. Travel, longitudinal 560 mm Max. travel travel, crosswise 240 mm Distance spindle center / table max. 450 mm Max. workpiece weight workpiece weight* 180 kg Grinding wheel 200 x 20 x 31,75 mm Table speed, hydraulic 7 - 25 m/min Cross adjustment Automatic feed, transverse 0.1 - 8 mm / stroke Rapid feed, cross 990 mm/min Cross feed per handwheel rotation 4 mm/rev. Graduation on handwheel 0.02 mm Vertical infeed Automatic feed, vertical 0.005 / 0.01 / 0.02 / 0.03 / 0.04 / 0.05 mm Rapid feed, vertical 480 mm/min Vertical infeed per handwheel revolution 2 mm/rev. Scale division on handwheel 0.005 mm Grinding spindle motor 2.2 kW Spindle speed 2850 rpm Hydraulic pump motor 0,75 kW Vertical feed motor 0,5 kW Length 2160 mm depth 1650 mm height 1840 mm Weight approx. 1640 kg * with magnetic clamping plate Scope of delivery - 2-axis digital display ES-12 H with LCD display - Siemens SMART panel IE V3 with touch operation - Electronic handwheel - grinding wheel - Wheel flange - LED work light - Magnetic clamping plate - Balancing stand - Balancing shaft Protective covers - Parallel puller - Demagnetizing device - Coolant device - Extraction diamond - Machine shoes - Central lubrication - operating tool