Used Sheet Offset for sale (9,262)

Condition: used, Year of construction: 2018, Overview This Krones Linatronic M is an empty bottle inspector for glass bottles, built in 2018. It inspects every empty container before filling and rejects any container that fails one of the inspection stages. The machine combines camera-based base, sealing surface, screw thread and sidewall inspection with high-frequency and infrared residual liquid and caustic detection. Two sidewall modules with four mirror assemblies and four cameras provide a compact full-front view of the container, and the DualFlash neck finish lighting inspects the outer and inner sealing surface separately using two minimally offset lighting angles. Foreign containers are identified at the machine infeed by height, contour and colour detection. Three Ecopush rejection points separate foreign, dirty and damaged containers. The machine is operated from a Krones iPanel CD terminal. Technical data - Manufacturer: Krones - Model: Linatronic M - Machine type: empty bottle inspector - Year of manufacture: 2018 - Application: inspection of empty bottles prior to filling; neck ring detection for returnable PET containers included - Inspection modules: base inspection, sealing surface inspection, screw thread inspection (cone optics), sidewall inspection - Sidewall inspection: 2 modules with 4 mirror assemblies and 4 cameras, two views per camera at 45° - Residual liquid and caustic detection: high frequency and infrared - Additional detection: polarising transparent films at container base and sidewall, glass fragments at the container base, scuffing via sidewall camera - Foreign bottle detection at the infeed: container height, contour and colour via camera - Rejection: 3 x Ecopush - foreign containers at the infeed, dirty containers and damaged containers at the discharge - Control: Krones iPanel CD operator terminal, prepared for data connection to a single-station PC (Datalyser) - Test bottle programme with 2D code - Conveyor height: 1,200 mm, adjustment range 1,155 - 1,315 mm - Minimum required room height: 2,810 mm - Overall dimensions: approx. 6,700 x 1,300 x H 2,800 mm - Direction of operation: right-left machine - Power supply: 400 / 230 V, 3/N/PE, 50 Hz, 6 A full load current, 20 A pre-fuse; auxiliary supply 230 V, 1/N/PE, 5 A - Standards: IEC 61439-1 / IEC 60204-1, CE marked - Machine base and housing: stainless steel (AISI 304 equivalent), clean design Equipment - DualFlash neck finish lighting, separate inspection of outer and inner sealing surface - Combined thread inspection via the sidewall mirror assembly - Fallen container detection in front of the machine (photoelectric sensors with infeed pusher) - Base blow-off unit with clocked air nozzle for foam and lubricant residues - Container blower at the infeed, conveyor dead plate (3-fold) - Servo-driven collection module for rejected containers at the discharge - Festo pneumatic system with maintenance unit, food-grade lubricants - Emergency mode: passage operation without inspection - OEM machine data sheet and dimension drawing Condition Fjdpfxezy Ud Is Ak Uepl Used, technically complete. The machine is still installed and under power at its production site; the photographs show it in the installed state. Availability Immediately. The machine will be dismantled and relocated to Germany. Viewing by arrangement; dismantling, loading and transport can be quoted on request.

Condition: used, Year of construction: 2021, machine/vehicle number: 13900, functionality: fully functional, DENER B-Servo 40-130 CNC servo-electric press brake. Technical data: - Year of construction: 2021 - Serial number: 13900 - Bending force: 40 t Fpsdpfxez Aa Eis Ak Ujl - Working length: 1300 mm - Back gauge: X + R axes - Tooling style: Eurostyle / AMADA Machine is located in Ivanjica, Serbia. Further information, additional photos and inspection on request.

Condition: excellent (used), Year of construction: 1998, operating hours: 61,000,000 h, functionality: fully functional, machine/vehicle number: 201810, color channels: 2, paper weight (min.): 50 g/m², paper weight (max.): 280 g/m², paper width (min.): 520 mm, total length: 290 mm, total width: 190 mm, total height: 170 mm, space requirement width: 300 mm, space requirement height: 220 mm, counter reading (black): 61,000,000, counter reading (color): 61,000,000, year of last overhaul: 2025, type of input current: three-phase, input voltage: 380 V, Equipment: documentation/manual, Heidelberg Speedmaster SM 52-2-P offset printing press for sale, manufactured in 1998, currently in daily production and available for inspection and live demonstration. Configuration * 2 printing units + perfecting device (1/1 or 2/0) * Maximum sheet size: 370 × 520 mm * Total impressions: 60,956,393 * AutoPlate semi-automatic plate changing system * Heidelberg Alcolor dampening system * Technotrans refrigeration unit for the dampening solution * Continuous feeder * Electronic side lays * CP Tronic control console * Automatic ink key presetting from the CP Tronic console * FullWash automatic washing system for the plate cylinders and ink rollers (blanket washing unit not installed) * Replaced cylinders Technical Condition * The press is currently in daily production and can be inspected while running. * Original Heidelberg ink and dampening rollers were replaced approximately 2 years ago (invoice available). * The machine runs perfectly and produces commercial print jobs every day. * Sold complete with a Plate Punch & Bender. Automatic Washing Systems The press is equipped with automatic washing systems for: * Impression and transfer cylinders; * Ink rollers. Fsdpozrr U Usfx Ak Uepl The blanket washing units are not installed. Documentation * Original purchase invoice available. * Original Heidelberg manuals and tools. * Original electrical diagrams. Terms of Sale * VAT invoice will be issued. * Dismantling, loading and transportation are the buyer’s responsibility. Ideal for Printing * Flyers * Brochures * Business cards * Folders * Forms * Labels * Commercial print jobs * High-quality promotional materials This press is an excellent choice for print shops looking for a reliable Heidelberg offset press with low operating and maintenance costs. Price €17,500 (VAT included).

Year of construction: 2012, condition: used, Empty weight: 9.250 kg Width: 18 cm Serial number: GS0000985 CP2000 Anicolor Damping Fsdpfx Akezuw Hus Uepl Complies with the CE standard: yes Maximum sheet size: 370 × 520 mm Maximum print size: approximately 360 × 520 mm. Maximum production speed: approximately 15,000 sheets per hour. Paper thickness: approx. 0.03–0.40 mm Dimensions: Length: 5.5 meters Width: 1.85 meters Height: 1.62 meters Weight: approx. 9,250 kg Includes operator console Note: The machine was delivered with a maintenance contract Online auction of high-quality printing, finishing, bookbinding, and paper-processing machinery from a modern graphic arts production environment, including a HEIDELBERG Varimatrix 105 CS automatic die-cutting and embossing machine, a HEIDELBERG Speedmaster SM 52-5 Anicolor 5-color offset press, a BOBST BRAUSSE Bora 1050 E die-cutting machine with stripping function, 2 HEIDELBERG Stitchmaster ST450 professional brochure production lines, a HORIZON StitchLiner 6000 fully automatic saddle-stitching line, HEIDELBERG Stahl TH 66 / TH 82 and XT 94 folding machines, a MÜLLER MARTINI Bolero automated high-speed line for collating and perfect binding with PUR and hot melt, POLAR 137 XT PACE and POLAR 137 XT AT XT Plus Autotrim fully automatic cutting lines, POLAR 115 XT and 92 ED cutting machines, AGFA Avalon CTP plate setters, MÜLLER MARTINI 1571 automated collator, PALAMIDES Delta 703 bundling and strapping machines, NEOPOST DS600i inserter, the EPSON Super Color T5200 large-format printer, the TECNOMAC Evolution 76 B1 laminator, the HEIDELBERG GTO 52 with Alcolor, various HEIDELBERG sheetfed presses, stack lifts, accessories, and graphic peripherals, etc. The online auction opens Friday 14 August and closes Thursday 17 September. Register your account via our website and place your bid. For viewings and inspections check the auction information on the website. Viewing days are on: - Thursday 3 September - Thursday 10 September - Monday 14 September Dome Auctions is an innovative auction platform dedicated exclusively to the industrial sector. By focusing on machinery sales from business closures, restructurings, and bankruptcies, we provide a trusted marketplace where buyers and sellers connect with confidence. Unlike general auction houses, Dome Auctions specializes in selling complete industrial assets directly from factories, ensuring quality and reliability. With a commitment to transparency, industry expertise, and tailored service, we streamline the sales process and maximize value for all parties. As online auctions continue to grow in the European industrial market, Dome Auctions offers a professional and efficient solution for companies seeking high-quality machinery at competitive prices.

Condition: used, 1 Color Press Heidelberg GTO46+ N+P in good Condition.   1 Farben Offsetdruckmaschine - 1 Color Sheet-Fed Offset Press Heidelberg GTO46+ N+P Year 1989 - Serial-No. 698328 Size max. 140 x 180 / 320 x 460 mms Fedpfxoylycnj Ak Uepl Dampening System VARN Compac Plus Version with Numbering and Perforation unit N+P Paperweight: 0.04 - 0.4 mms Speed: 3.000 - 8.000 sh/hr Online-Video-Inspection by WhatsApp - MS Zoom - Telegram On Stock Emskirchen/Nürnberg - Available Immediately - Can be test

Condition: used, Year of construction: 2021, machine/vehicle number: 12986, functionality: fully functional, DENER B-Servo 40-130 CNC servo-electric press brake. Technical data: - Year of construction: 2021 - Serial number: 12986 - Bending force: 40 t - Working length: 1300 mm - Back gauge: X + R axes - Tooling style: Eurostyle / AMADA Machine is located in Ivanjica, Serbia. Further information, additional photos and inspection on request. Fpjdpfxjz Aa Ecj Ak Uol

Condition: used, Year of construction: 2022, machine/vehicle number: 13180, functionality: fully functional, DENER B-Servo 40-130 CNC servo-electric press brake. Technical data: - Year of construction: 2022 - Serial number: 13180 - Bending force: 40 t - Working length: 1300 mm - Back gauge: X + R axes Fjdpfxsz Aa E No Ak Ujpl - Tooling style: Eurostyle / AMADA Machine is located in Ivanjica, Serbia. Further information, additional photos and inspection on request.

Year of construction: 2001, operating hours: 126,000,000 h, condition: good (used), machine/vehicle number: 204750, Perfecting 2/2 - 4/0 Fpsdpfx Akolml Nhe Ujl CPC 1-04: Off Press Ink & Register Control Alcolor Dampening Semi Automatic Plate Change Grafix Alphatronic 200: Powder Sprayer Technotrans Cooling Device Automatic Ink Roller Washing Device Blanket Washing Device Staticstar Compact: Antistatic Device Impression Account: 126 Mio.

Condition: used, functionality: fully functional, power: 650 kW (883.75 HP), total length: 48,000 mm, total width: 8,720 mm, total height: 6,464 mm, Year of construction: 2019, HIGH-CAPACITY 3-LAYER CO-EXTRUSION FLAT SHEET LINE (2100 mm) Manufacturer: FONG KEE INTERNATIONAL MACHINERY CO., LTD. (Taiwan) Model: TSE-90/150/150-2400 Year of Manufacture: 2019 Fpjdpfx Akjzzdnfe Ujl Condition: Used – Excellent condition, fully assembled and preserved indoors. KEY SPECIFICATIONS & PERFORMANCE: • Finished Sheet Width: Up to 2,100 mm (Net trimmed width) • Die Lip Width: 2,300 mm • Output Capacity: Up to 1,000 kg/h (depending on resin and sheet thickness) • Processable Materials: PET, PMMA, ABS, PS (HIPS / GPPS), PC, PP • Polymer Versatility: Configured for engineering thermoplastics and polyolefins (PET, PMMA, ABS, PS, PC, PP sheet extrusion). CO-EXTRUSION & FEED SYSTEM: • Configuration: 3-Layer Co-Extrusion (A/B/A or A/B/C) • Extruders: - Extruder A: Ø 90 mm - Extruder B: Ø 150 mm - Extruder C: Ø 150 mm • Melt Delivery: MAAG Gear Melt Pumps with Dynisco pressure transducers for ultra-stable flow • Extrusion Die: EDI (Nordson) Ultraflex HRC100-FB (2,300 mm, Made in USA) with Fast Gap patent adjustment CALENDER & DOWNSTREAM PROCESSING: • Polishing Stack: 3-Roll horizontal calender with high-precision mirror-finished rolls • Additional Roll Included: Dedicated Matte Calender Roll included with the line • Surface Finish Capabilities: Both High-Gloss / Mirror Optical Grade and Anti-Glare / Matte Finish • Temperature Control: Multi-zone thermoregulation units (TCU) • Protection: In-line dual-side protective masking film application unit • Cutting & Stacking: High-speed automated cross-cutter and automatic sheet stacker unit • Winding: In-line heavy-duty rewinder unit ELECTRICAL, DRIVES & AUTOMATION: • PLC System: Siemens SIMATIC (ET 200SP) with intuitive touchscreen HMI • Frequency Inverters: Siemens Sinamics G120 drive system • Main Electrical Switchgear: Schneider Electric • Cabinets: Independent air-conditioned industrial electrical enclosures FACILITY & FOOTPRINT: • Total Line Length: Approx. 48.0 m • Total Line Width: Approx. 8.7 m • Connected Drive Power: Approx. 650 kW (988 A) • Layout Drawing: Full technical CAD layout available upon request. CURRENT STATUS & INSPECTION: • Condition: Fully assembled, idle, and preserved indoors within a controlled industrial environment. • Availability: The complete line is immediately available for professional on-site visual inspection upon request. • Reason for Sale: Facility line reconfiguration.

Condition: used, maximum load weight: 35,560 kg, overall weight: 42,000 kg, axle configuration: 3 axles, first registration: 01/2026, next inspection (TÜV): 01/2027, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list: Complete equipment available upon request. Chassis * Regular ladder frame in lightweight steel construction * with continuous cross members, coupling plate 8 mm thick * with a 2-point kingpin according to DIN 74080 / ISO 337 Fsdpfezz Umxex Ak Uspl Suspension * Axle lift mechanism on axle 1, brand according to choice, Kögel * Three-axle unit * with disc brakes Ø 430 mm * Offset approx. 120 mm, air suspension with approx. 180 mm travel Vehicle tires * 6x 385/65 R 22.5 UNIROYAL TH 50 Chassis components * Landing gear (brand according to choice from Kögel), mechanically operated with leveling foot, lifting capacity approx. 24 t * One-sided operation on the right side when driving, splash protection system (spray mist suppression) according to Regulation (EU) No. 109/2011 * for three-axle unit with 385/65 R22.5 tires * consisting of 1 pair of quarter-circle fenders in front of the axles * 1 pair of straight fenders with mud flaps between the 1st and 2nd axles * 1 pair of quarter-circle fenders with mud flaps behind the axles * Storage box for: 10 side panels, folding stanchions, and rear door or rear flap. * Fully enclosed, protected against spray, also serves as a side protection, ground clearance (front) 220 mm * 2 plastic toolboxes, watertight, dimensions (internal) approx. 545 x 400 x 400 mm. * Installation at the rear, 1x on the left and 1x on the right, high, rigid underrun protection at the rear made of steel according to ECE-R58 * 1 pair of retractable warning signs for overwidth loads, retroreflective red/white, with LED lighting, spiral cable, and plug connection * Arrangement in the front and rear Vehicle area, brake / air suspension system * EBS system 2S/2M with stability program (includes ABS/ALB function) * EBS plug connection ISO 7638 (without connection cables) * Parking brake as spring-loaded brake * external pneumatic connections as well as external EBS diagnostic connection via ISO 7638 plug connection * WABCO EBS system * Air suspension system including 1 raising and lowering valve, mounted on the left side behind the axle unit when driving * Driving position adjusts automatically, 2 tamper-proof coupling heads in front ISO 1728 * Air tanks for brake system and air reservoir made of steel (EN 286-2) * Floor, flat floor approx. 30 mm thick, floor sealed around the perimeter, pocket for square tube inserts approx. 80 x 80 mm, arrangement according to drawing * 8 pieces of pocket strips (18 pockets per strip, 4 each on the outside + 10 in the middle) * Body, meets body strength according to EN 12642 XL (VDI 2700) * Tested for a payload of approx. 27,000 kg, front wall, storage for max. 14 square tube inserts approx. 80 x 80 mm (length approx. 1,990 mm) on the inside of the front wall, front wall approx. 2,000 mm high with steel corner brackets, with profiled steel sheet, screwed/riveted to the frame. * 2 pairs of lashing points (allowable lashing force approx. 1,000 kg per ring) on the front wall according to EN 12640 * Rear wall, foldable rear wall approx. 600 mm made of aluminum hollow profiles with 3 tension bars and T-handle locking mechanisms * 2 folding steps on the inside, folding steel corner brackets at the rear at the height of the side panels * Side wall, 4 pairs of folding stanchions at the height of the side panels * VarioFix steel hole outer frame * 4 pairs of stanchio

Condition: ready for operation (used), Year of construction: 2007, pressing force: 28 t, stroke length: 200 mm, throat depth: 200 mm, installation height: 325 mm, working length: 835 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Press force: 28 t Bending length: 835 mm Travel range of the back gauge: 0 – 370 mm Stroke: 200 mm Distance between frames: 890 mm Support table: 200 x 275 mm Overhang: 200 mm Installation height: 325 mm Number of cylinders: 1 Fodpfx Aozzkwgjk Ujpl Working speed Press travel: 8-10 mm/s Retraction: max. 35 mm/s Positioning accuracy: +/- 0.05 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 1,600 x 1,500 x 2,200 mm Total weight: 3,500 kg EQUIPMENT Operating manual Safety device Mechanical tool clamping (top) The height and weight of the asset must be taken into account when selecting the transport vehicle. A forklift is available for loading. If the asset is not collected on time, a storage fee of €20.00 per lot and per day (or part thereof) will be charged. The fee must be paid before collection. The sale is made without any warranty or guarantee. The information on the technical data comes from the original offer. No guarantee is given for typographical or measurement errors. If in doubt, please compare the information with the photos provided or inspect the goods on-site before the end of the auction.

Condition: ready for operation (used), Year of construction: 1988, functionality: fully functional, machine/vehicle number: 65951607, color channels: 4, paper weight (min.): 60 g/m², paper weight (max.): 500 g/m², paper width (max.): 720 mm, paper height (max.): 520 mm, input voltage: 400 V, Koenig Bauer / KBA Rapida SRO 4 | 1988 | Offset printing machine Year: 1988 Format: 52x72 cm Colours - 4‑colour offset Speed -12,000 sheets/hour Paper Weight - 60–500 g/m² Feeder - Mabeg (± Technotrans) Inking Adjustment - Colortronic remote key Fedpowzt Ttjfx Ak Ujpl Dampening - Technotrans / Varidamp (alcohol) Dryer - Infrared Powder Spray - Weko Cooling - Baldwin Cylinders Chromium-plated

Condition: used, Roll Forming Line for Drywall and Zinc-Coated Door Frame Profiles General Description: Complete roll forming line designed for the production of zinc-coated steel profiles used in drywall structures and door frame systems. The machine processes galvanized steel strips with thicknesses typically ranging from 0.6 mm to 1.0 mm, featuring quick roller adjustment depending on the required profile type. Profiles Produced - Drywall Profiles: • Galvanized Tracks: width 57 mm and 77 mm, height 35 mm, sheet thickness 0.6 mm • Galvanized Studs: 39×55 mm and 39×75 mm, sheet thickness 0.6 mm • U-Shaped Profiles for False Ceilings: 27×60×27 mm, sheet thickness 0.6 mm • Offset Profiles for False Ceilings: 20×29×28 mm, sheet thickness 0.6 mm - Zinc-Coated Door Frame Profiles (10/10 mm): • Complete range from ART. 201 to ART. 217, including L, U, Z and special shapes • Variable dimensions: widths from 20 to 46 mm, heights from 15 to 31 mm, customizable configurations available Technical Features • Material thickness: 0.6 – 1.2 mm • Strip width: variable, depending on profile • Number of forming stations: 19 • Rollers: hardened and ground steel rollers • Drive system: independent motorization for each roller group • Feeding speed: adjustable • Cutting unit: automatic flying shear or saw • Optional units: punching, slotting, or quick-change tooling systems Fsdpfoxnmyqsx Ak Uepl

Year of construction: 2008, condition: used, Year: 2008 Condition: Functional, dismontled in the warehouse Six-colour sheetfed offset press with coating tower including chambre coater (L) extended unloader (ALV) and carton equipment up to 1,2 mm Technical parameters: - Maximum sheet format: 740x1050 mm - Minimum printing format: 350x500 mm - Maximum speed: 15 000 sheets / hour - Usable materials: cca.60g/m^2 max 1,2mm - High of the stock: - loader 1300 mmm - unloader: 1200 mm - Double diameter impressions and transfer system Basic specification: Loader equipment: - Drive Tronic loader - Sheet splitting with 4 lifting and 6 transporting suction cups (2 of which are long jump suction cups) - Format presetting from the Ergo Tronic controle panel Loading equiment: - Pneumatic traction pads with automatic format adjustment via menu from the Ergo Tronic controle panel Print unit equipment: - Automated plate changing (SAPC) Color wheel equipment: - Color Tronic tinting with 35 zonal blades, each 30mm wide Fpsdsy H Hgdopfx Ak Uel Interpreter equipment: - Powder device WEKO AP 130 Gallery at the machine: - Ergonomic gallery on the device and oparator side Machine equiped: - Equipment for printing cardboard up to 1,2 mm o Manual skid steed loader o Equipment for carton management in printing units o Monitoring the pasage of sheets o Roll down roller shutter for stop-free unloading - Extended unloader / delivery 2600 mm - Full automatic plate changing with pneulatic plate bending device - Machine elevation by 375 mm - ACR Controle(automatic Register) - Connection to the existing Logotronic basic systém (CIP 3) - Connection to the existing Densitronic S console - Color zone status and measured values for Densotronic - Baldwin blankets and impression cylinders washing devices - Combined cooling / temperature controle - Baldwin unit - Grafix dusting with iuonization and connection to the controle panel - Infrared and hot air dryers in delivery

Condition: used, Year of construction: 2018, machine/vehicle number: A0221E1033, functionality: fully functional, operating hours: 31,621 h, table width: 1,500 mm, table length: 3,000 mm, Power: 3000 W Fpsdpozzyl Hefx Ak Usl Work area size: 3000x1500 mm Further details can be found in the images, and it comes with a commissioning guarantee.

Condition: ready for operation (used), operating hours: 99 h, functionality: fully functional, machine/vehicle number: 620110, year of last overhaul: 2026, HEIDELBERG SM-74-2 | 2-Color Offset Printing Machine Year of manufacture: 1994 Total impressions: 99 million Machine No.: 620 110 Printing specifications: - Cpc 1-04, CP Tronic - Max. sheet size: 530 mm x 740 mm (20.87" x 29.13") - Min. sheet size: 210 mm x 280 mm (8.27" x 11.02") - Max. print format: 510 mm x 740 mm (20.08" x 29.13") - Material thickness: 0.03 mm - 0.60 mm (0.0012" - 0.0236") - Gripper margin: 8 mm - 10 mm (0.32" - 0.39") Print output: - Maximum: 15,000 sheets per hour (sph) Plate cylinder: - Cylinder undercut: 0.15 mm (0.0059") - Distance from lead edge of plate to lead edge of print: 59.50 mm (2.34") Plates: - Size (L x W): 605 mm x 745 mm (23.82" x 29.33") - Thickness: 0.25 mm - 0.30 mm (0.0098" - 0.0118") Feeder: - Electronic pull lay control - Integrated preloading device - Ultrasonic and electromechanical double-sheet detector - Speed-compensated air blast - Self-cleaning pneumatic pull lay Printing Unit: - AutoPlate quick plate change system - Alcolor dampening system - Automatic wash-up devices (inking unit, blanket, impression cylinder) - TransferJacket Blue Delivery: - Non-stop delivery with rake - Super Blue delivery drum - Powder spray device Machine is in production and can be seen in operation. Fsdpey Sxb Djfx Ak Uspl

Condition: used, Year of construction: 2023, machine/vehicle number: 15718, functionality: fully functional, DENER B-Servo 40-130 CNC servo-electric press brake. Technical data: - Year of construction: 2023 - Serial number: 15718 - Bending force: 40 t - Working length: 1300 mm Fpedpfx Aez Aa Hajk Usl - Back gauge: X + R axes - Tooling style: Eurostyle / AMADA Machine is located in Ivanjica, Serbia. Further information, additional photos and inspection on request.

Condition: good (used), Uchida Aero Cut One Creaser, Slitter, and Cutter The machine is fully operational and ready for production. Description: The AeroCut One cuts, perforates, and creases sheets in a single pass. Only one person is needed to operate the device, significantly improving work efficiency and, consequently, reducing costs. The device is programmed using an intuitive touchscreen control panel. Cutting, creasing, perforating Fpsdpfszyz Dbjx Ak Uol Maximum paper size – 370 x 520 mm Min. paper capacity – 55 x 45 mm Maximum grammage – 400 g/m² Speed ​​– 11,130 business cards/h Paper types – offset, coated paper, varnished Feed – belt with adjustable vacuum Creasing – strip-type Memory – 263 programs + 150 user-defined Touchscreen programming PC connectivity Double-feed detection Weight: 240 kg Power supply: 230 V Made in Japan.

Condition: excellent (used), Year of construction: 2018, Ref:11138 . 2018 Horizon CRF-362 Creaser-Folder High speed automatic creasing / folding machine designed for both digital and offset printers to crease & fold digitally printed, heavyweight or cross-grained stock in one pass. Avoiding cracking of digitally-printed stocks. Quick and easy set-up and operation is performed through the high resolution colour touch screen. Suitable for creasing covers, restaurant menus, shop cards, invitation cards and laminated sheets. Preparing Perfect Bound Book Covers – sharp, high quality creasing prepares the spine, hinge and flap by selecting up or down creasing. High Quality Folding – two fold knives for high quality folding, even on heavy stocks. 6 different folding patterns can be set up simply by using the icon based touch screen. Specification: Maximum sheet size 364 × 865 mm Minimum sheet size 105 × 180 mm Feeding system Air suction feed belt Feeder pile height 150 mm Normal paper – crease & fold 80–350 gsm Normal paper – crease only 80–400 gsm Coated paper – crease & fold 105–350 gsm Coated paper – crease only 105–400 gsm Laminated stock – crease & fold 0.2–0.4 mm Laminated stock – crease only 0.2–0.5 mm Maximum crease lines 10 per sheet Fpodpfjzu Divex Ak Usl Creasing direction Positive / negative (up or down) Folding system 2 knife-fold units Speed: Up to 4,500 sheets/hour

Condition: ready for operation (used), Year of construction: 1983, Offset printing machine ULTRAMAN VII AGS/1983 Maximum sheet size 1120x1600 mm Minimum sheet size 600x800 mm Printing on 5 color groups + 1 dispersion varnish group Fpjdpfoy U Ufdex Ak Uel IR drying alcohol dampening and cooling Quick action plate clamps The machine is in good working condition.

Condition: used, Year of construction: 2022, functionality: fully functional, machine/vehicle number: 5480, EUROMAC XT FLEX 12S 1500/30-2500 CNC punching / nibbling machine. Technical data: - Year of construction: 2022 - Serial number: 5480 - Max. punching force: 30 t - Working range X axis: 2500 mm - Working range Y axis: 1500 mm - Multitool holders included: XMTE6 and XMTE10 Machine is located in Ivanjica, Serbia. Further information, additional photos and inspection on request. Fpodpsz Aaw Sefx Ak Usl

Condition: used, Year of construction: 2020, functionality: fully functional, machine/vehicle number: 5290, EUROMAC STX FLEX 12 1500/22-2500 CNC punching / nibbling machine. Technical data: - Year of construction: 2020 - Serial number: 5290 - Max. punching force: 22 t - Working range X axis: 2500 mm - Working range Y axis: 1500 mm Fsdpfxjz Aawxo Ak Uepl - Multitool holders included: XMTE6 and XMTE10 Machine is located in Ivanjica, Serbia. Further information, additional photos and inspection on request.

Condition: used, Year of construction: 1999, total length: 3,750 mm, total width: 2,250 mm, total height: 1,950 mm, Colour: Cream Weight: 7.600 kg - Year: 1999 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 6081991152 - Drive system: Conventional - Control system brand: Elgo - Drive type: Hydraulic - Configuration: Swing-beam - Power [kW]: 22.0 - Max. sheet thickness [mm]: 10 - Max. working width [mm]: 3100 - Cutting speed [mm/min]: 13 - Backgauge type: Electric - Backgauge depth [mm]: 800 - Sheet support system: None - Finger guard: Fixed - Angle adjustment: Motorized - Blade gap adjustment: Manual - Table type: Fixed table - Transport dimensions: 3750mm x 2250mm x 1950mm (l x w x h) - Transport weight [kg]: 7600kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Fodpfx Ajzz Rb Sok Uspl Lukas van Rossum

Condition: used, Year of construction: 2016, functionality: fully functional, machine/vehicle number: 4789, EUROMAC STX FLEX 12 1500/22-2500 CNC punching / nibbling machine. Technical data: - Year of construction: 2016 - Serial number: 4789 Fsdpfsz Aalvjx Ak Uspl - Max. punching force: 22 t - Working range X axis: 2500 mm - Working range Y axis: 1500 mm - Multitool holders included: XMTE6 and XMTE10 Machine is located in Ivanjica, Serbia. Further information, additional photos and inspection on request.

Condition: used, Year of construction: 1999, Offset 8 color with perfecting Heidelberg SM74-8-P-H Year: 1999 Number of impressions (mio): 247 Machine control - CP 2000 Feeder - Preset feeder - Suction feeder table - Double sheet control - Steel plate in feeder Printing units - Number of printing unit(s): 8 - Machine with perfecting: 8/0, 4/4 - AutoPlate - Alcolor dampening - Automatic inking roller washing device - Automatic blanket washing device - Automatic impression cylinder washing device - Dampening cooling and circulation system: Technotrans Fodpfjzdcx Ajx Ak Ujpl Delivery - Standard delivery - Powder spray