Used Return Device for sale (13,411)

Condition: like new (used), The system is a complete surf finisher system including suction station + undersize screening station + complete water treatment + water tank from Rösler. If required, including robot + handling portal. The components are transferred by robot to a portal with holders and immersed in the rotating surf container. The deburring performance is 20 seconds. Immersion time corresponds to about the same performance as 10-15 minutes. in a conventional vibratory finishing machine. Rotating work tank RMSF 4/800 1 piece round plastic container - Working tank diameter: 850 mm Working tank depth: 500 mm 1 pc. quick coupling for easy changing of the working container 1 pc. drive motor, power 7.5 kW 1 pc. dosing device D1-K/320 SF (circulating water) on stand 1 pc. stand for enemas in the working container 1 piece flow monitoring (by means of flow monitor) Undersize screening: 1 pc. Grinding wheel return system 1 piece underframe as a stable welded construction 1 pc. balancer for weight compensation (sanding pad + hose + nozzle) including mounting frame - Suspension for hose on the base 1 pc. vacuum generator for generating a negative pressure - Connection of the line system to the transfer device of the vibratory finishing system - Suction hose with nozzle, length approx. 5 m 1 piece collection container 500 liters as a cyclone separator - for receiving the process media that are sucked out of the working container, - for delivering the process media to the screening machine - incl. automatically operated gate valve and hose for returning the process media to the screening machine 1 pc. spray nozzles for rinsing out the collection container 1 pc. 2-hand control for flap 1 pc. dosing device DZ1-K Rösler screening machine R 12/6 SM-E - for undersize screening - Total length: 1,400 mm - Overall width: 1,160 mm - Screen area: 1,200 x 600 mm - Delivery height: 1,065 mm - Step in the separation zone: 1 x 40 mm - Drive power of vibration motors 2 x 0.525 kW - Vibration motors arranged laterally - Engine speed: 1500 rpm - Operating voltage: 400 V, 50 Hz, 3 Ph N/PE Rösler centrifuge Z 1000 ASS-II-Turbo with automatic sludge discharge consisting of: Centrifuge Z 1000 * Aluminum alloy centrifuge rotor * Speed: 2,050 rpm * Reduced stripping speed via frequency converter * automatically retractable paring knife * Amount of sludge per peeling cycle: up to 25 kg * automatic residual water drainage * Long bearing service life due to special bearings that can be relubricated Gkedpfx Ajyngitjk Uob * electronic vibration monitoring * automatic rotor flushing Accesories 1 piece mud truck RSKM 30 1 pc. Combined waste water and circulation tank 700/700 liters 1 pc. flocculant dosing pump DP2 1 pc. Automatic post-dosing DZ-4/320 2 suction lances (vacancy monitoring) 1 pc. sound insulation package approx. 80 dB(A) 1 piece cooling unit RK 3 1 piece titration measuring kit for manual compound measurement

Condition: like new (used), functionality: fully functional, power: 11 kW (14.96 HP), cutting height (max.): 115 mm, cutting width (max.): 4,200 mm, height adjustment type: electric, Equipment: CE marking, documentation/manual, rotational speed infinitely variable, saw blade guard, scorer, SCHEER PA 7012PK – 4200 x 4200 mm Like-new, high-performance panel dividing system with postforming unit, head cutting saws, and vacuum loading system. LIKE NEW - FROM THE MANUFACTURER - 1 year warranty For sale is a powerful and extensively equipped SCHEER PA 7012PK panel dividing system with a cutting capacity of 4200 x 4200 mm. The system has been professionally overhauled and is ideally suited for industrial furniture and interior design companies with high demands for precision, performance and automation. Technical data Cutting length: 4,200 mm Cutting height: 115 mm Saw blade overhang: 135 mm Main saw motor: 11 kW Scoring saw motor: 2.2 kW Automatic cutting height adjustment Residual cuts up to 5 mm possible Hardened guides Automatic forward and backward movement of the saw unit Main and scoring saws with integrated extraction Fully automatic angle pressing device Material feed HP 5107-4200 Servo-driven material pusher Feed speed up to 25 m/min Return speed up to 50 m/min 7 retractable clamping fingers Closed Pertinax surface in the stop area Air cushion system instead of rollers Control & Software Gsdpeza Eazsfx Ak Uekb with integrated industrial PC. Highlights: SSD hard drive Linux operating system Network-enabled (LAN/WLAN) Remote maintenance via TeamViewer / Remote Desktop Graphical cutting plan display Multilingual user interface 17" flat-screen monitor in swiveling control panel Virtually unlimited cutting plan management Optimization software OPTIMIN The integrated cutting plan optimization enables the direct creation and calculation of optimized cutting plans on the machine. Bills of materials are entered and automatically converted into economical cutting layouts. Postforming unit Integrated postforming unit Material height up to 80 mm Lift table TE 5085-4200 Four-spindle lift table Can be loaded from three sides Table size: 4,200 x 2,200 mm Stack height up to 650 mm Motor-driven roller conveyors on the right and left Fully automatic alignment systems Longitudinal alignment WP 5035-4200 Automatic positioning Working area 2,000 – 4,200 mm Transverse alignment WP 5034-4200 Three alignment fingers Working area 1,200 – 2,200 mm Front tables Angle stop table HP 5094-2406 3 workpiece support tables HP 5095-2406 Pertinax supports Air cushion system LK 5162 for all front tables Head cutting saws Main head cutting saw KS 5000-4200 Fully automatic positioning Adjustment range 300 – 2,100 mm Extended travel up to 3,100 mm Power 7.5 kW Integrated top and bottom extraction Additional head cutting saw Manually adjustable Positioning 0 – 50 mm from the stop edge Power 7.5 kW Vacuum loading system TE 5088-4200 Additional pusher with integrated short-stroke vacuum loading system. The panels are automatically transferred from the lift table to the pre-stacking table and fed into the processing process. This enables short cycle times and a high degree of automation. Conclusion An extremely rare and fully equipped industrial panel dividing system with extensive automation, postforming equipment, double head cutting system and vacuum loading. Ideal for the furniture industry, shop fitting, interior design, as well as larger carpentry and joinery businesses. Machine available immediately – 1 year warranty.

Condition: used, Year of construction: 2008, pressure 180 t chamfer lenght 3110 mm distance between columns 2600 mm column arm 410 mm ajustment speed 100 mm/sec working feed 10.0 mm/sec return speed 80.0 mm/sec back stop - adjustable max. 750 mm stroke 260 mm dayligth 460 mm table height 880 mm oil volume 210 ltr. operating pressure max. 240 bar control DELEM total power requirement 15.0 kW weight of the machine ca. 11.200 kg. range L-W-H 4250 x 2000 x 2800 mm Current new price approx. 85.000 euros Special price on request Features: - Electro-hydraulic CNC press brake - With DELEM CNC control model “DA 66W” * 2D graphic programming * Automatic bend sequence calculation and collision detection * High-quality LCD screen (TFT) * Swivel control panel, front left - CNC-controlled axes: Y1 + Y2 + X + R + CNC crowning - CNC electric motor-driven backgauge (X axis) * with 2x manually adjustable stop fingers Godpsxa Hivjfx Ak Uskb - CNC electric motor height adjustment of the backgauge (R axis) - CNC electric motor table crowning - ROLLERI upper tool adapter (quick-change clamping) * including crowning device in the tool holder - 2x front, sliding support arms (“sliding” system) - Side guard (swivel doors) - Rear guard (sliding door) - 1x freely movable 2-hand/foot control - Operating instructions (PDF)

Condition: ready for operation (used), Year of construction: 2001, pressure 100 t chamfer lenght 4100 mm distance between columns 3700 mm column arm 415 mm stroke max. 215 mm dayligth 410 mm ajustment speed 200 mm/sec Gkedpfx Asxzuwksk Usb working feed 10.0 mm/sec return speed 150 mm/sec work height max. 1080 mm table width 100 mm Control CYBELEC oil volume 160 ltr. voltage 400 V power capacity 8.5 kW weight 10200 kg range L-W-H 4800 x 1800 x 2600 mm - in checked conditions - machinevideo - ?v=Phcik_oo4CE Equipment: - BEYELER electro-hydraulic CNC press brake - CNC CYBELEC control unit “DNC 1200 PS/B” * High-resolution screen * Clear, concise menus in the operator's language * Tool and product library * Swiveling control panel, front right - CNC-controlled axes (Y1+Y2-X) - CNC-controlled backgauge adjustment (X-axis) * 2x manually adjustable stop fingers - Manual upper tool clamping - Manual lower tool clamping - Rear safety device (safety door) - Side safety device (safety doors) - Bending tools * 1x set of split upper tools (ROLLERI TOP 175.26.R08) * 1x set of split 1V dies (V 12 mm) - 2x freely movable 2-hand controls - 2x freely movable foot switches - Operating instructions for control system

Condition: excellent (used), The fully hydraulic production rapid bow saw is equipped with a universal hydraulic system allowing for exclusive or alternating cutting of thin- and thick-walled profiles as well as solid material, without the need to change the saw blade, utilizing a uniform tooth pitch of 3 or 4 teeth per inch. Features include preloaded bow guide, enclosed oil hydraulics, triple pivot bearing, separate coolant system, steplessly adjustable hydraulic cutting pressure, lift motion and accelerated return stroke, and is factory-equipped with an infinitely variable miter facility. The saw bow can be lifted in rapid traverse mode. The pendulum vise ensures optimum saw blade utilization. The longitudinal guide features ground and hardened guide rails for transmitting cutting forces to the saw bow. Automatic end-of-cut shut-off. Push-button controls for ON, OFF, and rapid traverse of the saw bow. Manufacturer: KASTO Machine type: Metal bow saw Model: PSB 253 U Drive power: 1.6 kW Stroke rates: 50 / 100 / 164 per min Cutting speed: 11 / 22 / 36 m/min Universal hydraulics: standard Saw feed: Hydraulic Round cutting capacity: 255 mm Flat cutting capacity: 255 x 160 mm Miter range: 0-45° Workpiece support height: 500 mm Weight: 490 kg Length/width: 1200 x 750 mm Height: 850 mm Saw blade dimensions: 400 x 36 x 2.0 mm Year of manufacture: 1990 Gkedsxiv Sfopfx Ak Usb Accessories: Coolant device

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, Unicontrol 12 Consisting of: Cut-off unit (item A), Tenon and slotted spindle (item C), Transfer belt (Pos. I), profiling spindle (Pos L), profiling spindle (Pos. N), Profile shaving unit vertical right (Pos. P) For the production of individual parts and elements in frame-by-frame or serial production. Consisting of a cross processing unit and a longitudinal processing unit connected to a transfer belt. Working width 40-140mm (See pressure ruler left 40 - 140 mm) Working height 40-120mm Workpiece length min. approx. 275 mm + 1 x end profile length Long machining: approx. 220 mm + 2 x end profile length Gkjdpfx Aoumci Sok Usb Workpiece length max. 3500 mm The part dimensions depend on the machine equipment, production type and tool assignment. A final definition of the part dimensions is only possible after receipt, inspection and approval of the complete and final layout drawings. Cross machining: Table feed Motor power 0.3 kW (0.4 HP) Pre-set feed speed for cutting, profiling and return 3-25 m/min Vario table with (studio window production possible) The clamping length of all tenoning and slotting spindles can be used without a tool blank. Workpiece clamping by means of a clamping bridge. Operated by a clamping cylinder installed under the table. NC-controlled long fence mounted on the slotting table. Studio window device Swivel angle max. +/- 75° The minimum workpiece length for slanted windows depends on the angle and the width of the wood. Possible part dimensions for slanted window production Angle Max. Min. Working width Workpiece length +/-75° 80 mm 800 mm +/-70° 120 mm 490 mm +/-60° 240 mm 360 mm +/-90° 350 mm 185 mm For angles greater than 60° only counter processing Commission not documented 1)NC automatic angle adjustment for machining angled parts Splinter protection by means of overtravel counter Over the entire spindle length of the tenoning and slotting spindle for 90° machining Manually trackable counter-rail for angled part machining 2) Additional counter-rails

Year of construction: 1980, condition: used, Max. tensile force: 10 tons Max. stroke: 1250 mm Max. cutting speed: 10 m/min Gkodpfocdtplox Ak Ujb Max. return speed: 27 m/min Max. workpiece diameter: 320 mm Number of units: 3 Weight: 4.8 tons Automatic tool feeder Hydraulic draw-in head and end piece holder locking system Automatic feeding device for workpiece diameters up to 100 mm Magnetic belt chip conveyor

Condition: ready for operation (used), Year of construction: 2019, operating hours: 1,000 h, functionality: fully functional, machine/vehicle number: DRYER DPS180, overall weight: 10,000 kg, total height: 6,000 mm, total width: 8,000 mm, total length: 20,000 mm, year of last overhaul: 2019, PET material dryer for regrind. Operational. Must be removed within 2 months. Gjdpfxszz Iaxj Ak Uokb

Condition: ready for operation (used), Year of construction: 2000, pressure 85.0 t chamfer lenght 2050 mm distance between columns 1650 mm column arm 400 mm stroke 240 mm dayligth 320 - 560 mm ajustment speed 150 mm/sec working feed 15.0 mm/sec return speed 150 mm/sec back stop - adjustable 5.0 - 1000 mm table width 110 mm work height max. 1050 mm operating pressure max. 297 bar compressed air 4.5 - 6.0 bar oil volume 200 l operating pressure 340 bar total power requirement 7.5 kW weight of the machine ca. 5900 kg range L-W-H 4100 x 2100 x 2750 mm with increased installation height / piston stroke well-maintained condition (!!) - in checked condition - machine video - ?v=ikl6RNZWeiU Equipment: - CNC electro-hydraulic press brake - including CYBELEC CNC control * swiveling control panel at the front right * external screen - CNC axis adjustment: Y1 - Y2 - X - R - Z1 - Z2 - I + CNC crowning - CNC electro-motorized back stop (X axis) * Travel range .. 5.0 - 1,000 mm * Travel speed .. 250 mm/sec. - CNC electro-motorized height adjustment of the back stop (R axis) * Travel range .. 70 - 235 mm * Travel speed .. 100 mm/sec. - CNC electro-motoric adjustment of the stop fingers (Z axes) * Travel range Z1 .. 405 - 1.565 mm * Travel speed .. 1.000 mm/sec. * Travel range Z2 .. 485 - 1.645 mm * Travel speed .. 1.000 mm/sec. - CNC electro-motoric table crowning - CNC pneumatic die displacement (I axis) - EHT pneumatic tool clamping - upper tool - EHT manual tool clamping - lower tool * Tool holder 90.0 mm + 13.0 mm possible - 1x freely movable 2-hand/foot control - 2x front, stable support arms including "sliding system" - side protective device (swinging doors) - rear protective device (swinging door) - original operating instructions + circuit diagram etc. * Special accessories included: Gsdpfx Aoxab Ugjk Uskb - Oil cooler for use in continuous operation

Condition: used, machine/vehicle number: 25278, Year of construction: 2016, operating hours: 9,287 h, load capacity: 1,600 kg, lifting height: 3,140 mm, free lift: 1,450 mm, fuel type: electric, mast type: duplex, construction height: 2,120 mm, Equipment: sideshift, .: 25278 Device details: Year of manufacture: 2016 Load capacity: 1600 kg Lift height: 3140 mm Recorded operating hours: 9287 h Free lift: 1450 mm Mast type: Duplex Mast height: 2110 mm Length/Width/Height: 2060 / 1100 / 2120 mm Operating weight: 3448 kg Battery from: 2016 ---- Equipment: * Protective roof * 3rd valve * Full free lift * Front work lights ----- Attachments: * Sideshift ---- Additional device information: Ready-to-drive as returned by the customer---- Operating hours are generally read hours. We will gladly offer you suitable transportation. Another 250 - 300 forklifts, attachments, and sweepers are immediately available for you. Of course, also for rent! We are happy to buy your OLD one. Do you have questions? You can reach us during our business hours from 7:30 a.m. to 4:00 p.m. We look forward to seeing you! Gksdstw Ab Dopfx Ak Usb We speak English Interim sale and errors for this offer are expressly reserved. In dealer transactions, the device is sold as is, not refurbished. All information without guarantee, errors and changes reserved.

Condition: ready for operation (used), Year of construction: 2014, pressure 40.0 t chamfer lenght 1600 mm distance between columns 1100 mm stroke of upper beam 100 mm throat 195 mm working feed 10.0 mm/sec return speed 70.0 mm/sec 180 bar work height max. 840 mm table width 110 mm dayligth 295 mm Control ATS 585 total power requirement 5.5 kW weight 2500 kg range L-W-H 2100 x 1200 x 1800 mm - in checked conditions - machinevideo - ?v=l9CdurfDGb0 Features: - NC-controlled hydraulic press brake - with ATLANTIC NC control "ATS 585" * Rear stop positioning (X-axis) * Depth adjustment positioning (Y1, Y2 axes) * Ability to program various programs * Swiveling control panel, front left * Tool and program library - NC electric-motor-driven material/backgauge (X-axis) * With 2 stop fingers, manually adjustable (R and Z axes) - Tool holder system A - with upper wedge camber - Split insert/bending tools - DSP LASER "RX" safety device - front - 2x side, swiveling safety doors - 1x freely movable double foot control - Operating instructions Also included in the scope of delivery (pre-installed): - 1x brand-new / split set of upper tools * UKB 11,200 mm - 2x 835 mm * Angle 85° - Radius R 0.8 mm - Height 66.5 mm * Load capacity 1000 kN/m max - 1x brand-new / split set of lower tooling * UKB 21.207 - 2x 835 mm * V-openings = 16/22/35/50 mm * Angle 85° * Load capacity 800 kN/m max. Godpfx Aksy Nd Tyo Uekb

Condition: used, Year of construction: 2007, Schmalz A-175N-47/B-19 DI Piston Metering Pump, 6 bar, Metering Pump Manufacturer: Schmalz GmbH Device type: Piston metering pump Type: A-175N-47/B-19 DI Series according to documentation: SR Design: Metering pump with return spring Year of manufacture: 2007 Maximum pressure: 6 bar Gkodpfjzxrn Iox Ak Ujb Flow rate at 50 Hz: 226 l/h Flow rate at 60 Hz: 271 l/h Metering rate: adjustable Drive: Three-phase motor Motor type: 71 A 4 Motor protection class: IP55 Condition: used

Condition: used, Year of construction: 2001, pressure 130 t chamfer lenght 3060 mm distance between columns 2690 mm column arm 410 mm stroke 365 mm dayligth 535 mm ajustment speed 200 mm/sec working feed 1.0 - 10.0 mm/sec return speed 135 mm/sec table width 120 mm table height 1050 mm tiltable up to +/- 10.0 mm Number of working hours ca. 31.800 h compressed air 5.0 - 7.0 bar oil volume 250 l operating pressure 340 bar voltage 400 V total power requirement 23.0 KVA weight of the machine ca. 12950 kg range L-W-H 3660 x 2310 x 2900 mm Equipment: - CNC electro-hydraulic folding/die bending press - DELEM CNC control - swiveling front left * High-resolution graphic screen * Clear, concise menus in the operator's language * Large tools and products library * Graphical 2D programming * automatic bending sequence calculation and collision detection * EMERGENCY stop button at the front Godpfx Akeyn R Hvj Uekb - CNC axis adjustment: * Y1 - Y2 - X - R axis CNC crowning * Manual adjustment of the 2x stop fingers, from the front (Z axes) - CNC electro-motorized table crowning - CNC electro-pneumatic die displacement (I axis) - WILA / TRUMPF upper tool clamping - hydraulic - WILA / TRUMPF lower tool clamping - hydraulic - 2x front, robust support arms - movable - 1x freely movable 2-hand/foot control - 1x free-moving foot switch - Lateral safety device (hinged doors) - rear safety device (sliding doors) - original operating instructions ( french )

Condition: used, mileage: 10 km, first registration: 12/2024, color: orange, Your specialist dealer with expertise, service, and advice offers you: Gsdjvvp Rxspfx Ak Uskb SCHMAILZL gully cleaner for Multicar, other vehicle manufacturers, and trailers (the attachment is offered without vehicle) Net price: €14,550 plus 19% VAT. (New device with 12-month manufacturer’s warranty) Base unit type SKR II - Painted in RAL 2011, including: - Adjustable frame (1.2–2.0 m wide) with lifting and emptying device - Swivel device with cylinder and chain suspension for manhole covers - Lifting winch (lifting capacity approx. 150 kg) - Hydraulic vibrator – cover lifter - Wind protection – fastening materials - Net weight approx. 300 kg The very simple operation and ergonomic working process make this affordable device, in combination with a tipper vehicle, a genuine alternative to conventional methods. Additional advantages: - Low fuel consumption as operation is almost at idle speed - Mounting and dismounting take only a few minutes, important for changing assignments - Emptying 150–300 silt boxes per day is possible - Emptying without water addition thanks to hydraulic vibrator - The unit can be installed on various vehicles using the telescopic frame The following requirements must be met by the carrier vehicle: - Hydraulic connection 20–30 L/min, 150 bar - Free return line, size 15 - Lashing eyes on the tipper platform Optional equipment for vehicles or trailers without their own hydraulic drive: Petrol hydraulic unit consisting of: Petrol engine 9 HP/6.7 kW, 20 L/min at 2400 rpm, 8.4 cm³/rev gear pump, manometer, 40-liter tank with oil level indicator and damping mount Dimensions: approx. H 80 x W 65 x D 55 cm, weight: approx. 70 kg Net price: €4,350 plus 19% VAT. Assembly, shipping, or delivery available on request. On request, we are happy to offer complete packages with vehicles, also available in right-hand drive versions. We also gladly provide an offer for the installation or retrofit of your vehicle with the demountable tipper body including a DEKRA main inspection report for the conversion. Errors, changes, and prior sale reserved. Our Terms and Conditions apply. Take advantage of our many years of experience in sales and service and let us prepare an individual offer for you. Make use of our leasing and financing options as well. We promise competent advice and support from our qualified staff. You will find further offers from the commercial vehicle manufacturers MULTICAR, ISUZU, and PIAGGIO as well as an extensive range of attachments at Tel.:

Condition: ready for operation (used), Year of construction: 2010, pressure 160 t chamfer lenght 4100 mm distance between columns 3600 mm column arm 400 mm ram stroke speed 200 mm/sec work speed 10.0 mm/min return speed 165 mm/sec work stroke ca. 350 mm dayligth ca. 660 mm oil volume 450 ltr. table height 830 / 950 mm table width 75.0 / 60.0 mm voltage 400 Volt total power requirement 18.5 kW weight 13440 kg range L-W-H 5150 x 2050 x 3150 mm current new price approx. 90.000 euros special price on request ----- ULTIMA PLUS electro-hydraulic press brake with: * increased installation height .. approx. 660 mm * increased cylinder stroke .. approx. 350 mm ----- - in checked condition - machine video - ?v=chgCaXLnpa8 Equipment: - CNC electro-hydraulic die/press brake - CYBELEC CNC control "DNC 880 S" * swiveling control panel, front right * 2D graphic programming & product display * tool & program library - CNC controlled axes: Y1 + Y2 + X + R axis Gsdpfx Aexaambok Ujkb - CNC electro-motorized back stop, with ball screws (X axis) - CNC electro-motorized Height adjustment of the stop beam (R axis) - 2x manually adjustable back stop fingers (Z axis) - 2x front, movable support arms with T-slot ("Sliding System") - 1x set of bending/insert tools * AMADA / SYSTEM A tool system - Laser protection device in front of the machine - Safety device behind the machine (door) - 1x freely movable foot switch - original operating instructions

Condition: used, Year of construction: 2013, Number of spindles 5 St. Working width 20 - 230 mm Working height 8 - 120 mm Length of the planing table 2500 mm Feed motor 1,1 kW Feed speed stufenlos regelbar 2-12 m/min. weight of the machine ca. 2500 kg Control MemoryPlus 1 WEINIG VARIOMAT Planing and Moulding Machine ----- Brief Summary: ----- - 5 spindles - Powerful motors - Cycle-controlled jointing - MemoryPlus control system - Option: Stähle-Hess Saturn single-piece sanding machine Technical Manufacturer's Description: ----- Working width: 20 – 230 mm Working height: 8 – 120 mm 1st Spindle: Horizontal Bottom ----- Motor with brake: 7.5 kW Diameter: 40 mm Speed: 6000 rpm Tool cutting circle: 125 – 145 mm Axial adjustment range: 5 mm Rebating device incl. rebating cutters 2nd Spindle: Vertical Right ----- Motor with brake: 11.0 kW Diameter: 40 mm Speed: 6000 rpm Tool cutting circle: 93 – 232 mm Minimum tool diameter at fence level: 93 mm Maximum tool diameter behind fence level: 180 mm Maximum moulding depth: 45 mm Axial adjustment range: 30 mm Insert segment incl. additional fence lip: 125 mm Insert segment incl. additional fence lip: 150 mm 3rd Spindle: Vertical Left ----- Shared motor with 1st right spindle Gkjdpoy Spvfjfx Ak Ueb Diameter: 40 mm Shared speed with right spindle Tool cutting circle: 93 – 232 mm Maximum moulding depth: 45 mm Minimum moulding depth at 200 mm tool cutting circle: 20 mm Axial adjustment range below table: 30 mm Insert segment: 125 mm Insert segment: 150 mm 4th Spindle: Horizontal Top ----- Motor with brake: 11.0 kW Diameter: 40 mm Speed: 6000 rpm Tool cutting circle: 125–200 mm Maximum rebate depth: 30 mm Minimum rebate depth (for tool cutting circle up to 200 mm): 20 mm Axial adjustment travel: 30 mm 5. Horizontal Bottom Spindle ----- Motor with brake: 11.0 kW Diameter: 40 mm Speed: 6000 rpm Tool cutting circle: 125–200 mm Maximum rebate depth: 15 mm Axial adjustment travel: 10 mm Table plates with wooden inserts for the bottom spindle Additional outfeed plate above the bottom spindle for wooden inserts Feed System ----- Frequency-controlled feed: 1.1 kW, infinitely variable (2–12 m/min) Double-pendulum roller opposite the left spindle Axial adjustment travel of feed rollers opposite the left spindle: 35 mm Durofer-coated spiked feed rollers Pneumatic pressure for feed rollers (incl. water separator) Cycle-controlled jointing to support manual jointing. The infeed roller is released once the second feed roller has engaged the workpiece. After the workpiece clears the second feed roller, the infeed roller returns to its starting position for the next workpiece. Additional Features: ----- MemorPLUS Control System Width and height adjustment via controls (Spindles 3 and 4: radial CNC-axis controlled) ----- Price for the above-mentioned machine available upon request! ----- OPTIONAL ADD-ON (at extra cost) — Stähle-Hess Saturn #7008: Machine previously used in conjunction with the Stähle-Hess Saturn Duo Single-P...

Condition: ready for operation (used), Year of construction: 1998, pressure 85.0 t chamfer lenght 2050 mm distance between columns 1750 mm column arm 410 mm stroke 365 mm dayligth 535 mm ajustment speed 200 mm/sec working feed 1.0 - 10.0 mm/sec return speed 135 mm/sec back stop - adjustable max. 600 mm table width 120 mm work height max. 1050 mm Number of working hours 28.500 h oil volume 200 l operating pressure 340 bar total power requirement 14.0 kVA weight of the machine ca. 9050 kg range L-W-H 2680 x 2100 x 2885 mm with increased installation height / piston stroke very well maintained condition (!!) with only approx. 28.500 operating hours - in checked condition - machine video - ?v=ZuwyPKJSYLw Equipment: - CNC electro-hydraulic press brake Gkedpfexaa Ursx Ak Ujb - including DELEM CNC control * swiveling control panel at the front left - CNC controlled axes: Y1 - Y2 - X - R - Z1 - Z2 - I + CNC crowning - CNC electro-motorized back stop (X axis) - CNC electro-motorized height adjustment of the back stop (R axis) - CNC electro-motorized adjustment of the stop fingers (Z axes) - CNC pneumatic die displacement (I axis) - CNC motorized table crowning - WILA electro-hydraulic upper tool clamping - WILA electro-hydraulic Lower tool clamp - 1x freely movable 2-hand / foot control - 2x front, stable support arms including "sliding system" - side protective device (swinging doors) - rear protective device (swinging doors) - bending tool storage cabinet (right front, side) - original operating instructions + circuit diagram etc. further technical data: - feed speed X axis .. 500 mm/sec. - feed speed R axis .. 300 mm/sec. - feed speed Z axis .. 1000 mm/sec. - travel range X axis .. max. 600 mm - travel range R axis .. max. 250 mm

Condition: ready for operation (used), Year of construction: 2007, Stiefelmayer Brivisor KL-4 Hardness Testing Machine Testing height: 150 mm (with testing table) Outreach: 200 mm Device footprint: 560 mm x 250 mm x 770 mm (W x D x H) Load range: 0.05 - 10 kgf Weight: approx. 45 kg Year of manufacture: 2007 Gkedozzynhspfx Ak Ueb Vickers: HV 0.1 | 0.3 | 0.5 | 1 | 2 | 3 | 5 | 10 Brinell: HBW 1/5 and HBW 1/10 You are welcome to visit us for an inspection. We can also arrange cost-effective shipping for you! You will receive a proper invoice. For foreign customers, a net invoice can also be issued. A valid VAT identification number is required. Subject to prior sale. Visit our shop and view our other offers. The company names and trademarks mentioned are the property of their respective owners and are used solely for identification and description of the products. Deviations in technical data as well as errors in the description of the article may occur and are subject to change.

Condition: used, machine/vehicle number: 25286, Year of construction: 2016, operating hours: 7,307 h, load capacity: 2,000 kg, lifting height: 5,050 mm, fuel type: diesel, mast type: simplex, construction height: 3,120 mm, Equipment: sideshift, .: 25286 Device Details: Year of manufacture: 2016 Load capacity: 2000 kg Lifting height: 5050 mm Read operating hours: 7307 h Mast type: Standard Mast height: 3120 mm Length/Width/Height: 2600 / 1200 / 2160 mm Operating weight: 3595 kg ---- Features: * Protective roof * 3rd valve * Half-cab * Work light front * Work light rear ----- Attachments: * Side shifter * Load guard ---- Further Device Information: Bluespot Godpfx Ajtw A U Djk Uokb Flashing light Single pedal Drive-ready as-is condition, as returned by the customer---- The operating hours are generally read-off hours. We are happy to offer you suitable transport. A further 250 - 300 forklifts, attachments, and sweepers are immediately available for you. Of course, also for rent! We will gladly buy your OLD one. Do you have questions? You can reach us during our business hours from 7:30 am to 4:00 pm. We look forward to seeing you! We speak English. Interim sale and errors for this offer are expressly reserved. In the dealer business, the device is sold in its AS-IS condition, not reconditioned. All details without guarantee, errors and changes reserved.

Condition: ready for operation (used), Year of construction: 2004, pressure 50.0 t Godpfoxab U Hex Ak Uokb chamfer lenght 1275 mm distance between columns 1040 mm column arm 250 mm ram stroke speed 225 mm/sec work speed 0 - 9.8 mm/sec return speed 160 mm/sec work stroke 215 mm dayligth 512 mm table height 800 mm back stop - adjustable 600 mm control DELEM DM 51 operating pressure max. 300 bar oil volume 150 ltr. voltage 400 V engine output 6.0 kW Weight 4300 kg range L-W-H 1930 x 1510 x 2390 mm current new price approx. 80.000 euros special price on request good / well-maintained condition (!!) - in checked condition - machine video - ?v=5L8L2AYv0PU ----- PLACKE electro-hydraulic CNC press brake specially developed for the production of small parts The advantages: • Low energy consumption • High operating comfort • Wide range of applications • Fast, robust, low-noise • With CNC control as standard ----- Equipment: - CNC electro-hydraulic press brake with 1x working cylinder - DELEM CNC control model "DM 51" - CNC controlled axis: Y1 - Y2 - X - CNC electro-motorized back stop * Travel path: X = max. 600 mm * Travel speed X axis .. max. 300 mm/s * Positioning accuracy .. +/- 0.02 mm * with 2x manually adjustable stop fingers (R+Z axis) - WILA standard - manual upper tool clamping - WILA standard - manual lower tool clamping - PLACKE safety device at the front: light barrier - side protective device (swivel doors) - rear protective device (swivel + lockable door) - front storage area - side sorting system for bending tools - 1x freely movable foot control - original operating instructions including circuit and hydraulic diagram

Condition: used, Year of construction: 2006, with automatic lifting table feeding system with 4 precision spindles, ensuring the stack is always held evenly at the correct level. Equipped with 4 powered roller groups. Lifting table dimensions: 6000 x 2200 mm. Feeding side: left (from the operator's perspective). Max. stack height: 450 mm. Lifting table height (bottom): to be defined. Speed for lifting and lowering: 0.7 m/min. Lifting table drive: 3 kW. Powered roller group: 4. STANDARD CONFIGURATION. Usable cutting length: 6000 mm. Lifting table feeding: Yes. Working height: 950 mm. Saw blade overhang: 100 mm. Clamping device opening: 117 mm. Machine control: G Drive RT. Number of clamping devices movable in X: 1. Number of clamping devices movable in X and Y: 1. Number of fixed clamping devices: 1. Min. material thickness (with side alignment): 10 mm. Min. material thickness (with lifting table feeding): 10 mm. Min. panel dimension (with lifting table feeding): 2400x1200 mm. Max. panel dimension (with lifting table feeding): 5500x2070 mm. Max. panel dimension (without lifting table feeding): 5800x2010 mm. Safety device according to CE: included. Supply voltage: 400 V / 50 Hz. MACHINE CONFIGURATION. Machine bed: The machine bed structure made of steel is welded using arc welding and then milled and finished on CNC machines. The rigid structure of the machine bed guarantees both high cutting quality with high cutting speed, as well as the enormous durability of the entire machine. Saw blade overhang: 100 mm. Power of main saw motor: 7.5 kW. Power of scoring saw motor: 2.2 kW. Diameter of main saw blade: 400 mm. Diameter of scoring saw blade: 215 mm. Feed rate of saw carriage: Forward: 1-170 m/min. Return: 170 m/min. Motorization of saw carriage feed: Servo drive. Diameter of dust extraction port (bottom, 1x): 200 mm. Diameter of dust extraction port (top, 2x): 115 mm. Thanks to the rigid machine bed construction, the masses are distributed in the best possible way, which prevents twisting and thus guarantees an absolutely vertical run of the saw blade. Machine table made of steel with individual, removable support elements made of high-quality, durable material. The saw carriage runs on two round guides, which are mounted horizontally on one level. Large prism rollers (diameter 86 mm), with spring-loaded counter rollers, ensure smooth linear feed, as well as very low contact pressure and enables virtually wear-free operation of the saw carriage. The weight and forces acting on the saw carriage are evenly distributed on the two guides (50/50) and on each individual prism roller. The saw carriage runs absolutely without lubricant on the guides. The two guides are located away from the cutting line, outside the direct dust area. The diameter of the guide rods is 40 mm, making them the largest and most stable guides used in this sector. Pneumatic quick clamping system; for quick and convenient tool changes. This system is extremely reliable in operation, as it is mechanically clamped via a flange with a bayonet lock and spring force and unlocked via a pneumatic quick coupling. The flange must be rotated by approx. 10° in order to remove it. Due to excellent accessibility and the fact that the operator does not need any other tools, the tool change is very easy and can be carried out in seconds. The scoring saw adjustment is made from the outside. Gkodpjzn N Ikefx Ak Uob

Condition: good (used), Ideal 7260 Hydraulic Paper Guillotine Machine in very good condition, ready for production. This professional cutter is designed for high-performance cutting. This model offers excellent value for money. The guillotine has a 721 mm knife length and is equipped with infrared safety curtains, a hydraulic hold-down device, and an electromechanical cutter bar drive. Standard equipment also includes a programmable program with 99 steps each, electronic saddle position reading with 1/10 mm accuracy, and a self-diagnostic system with error messages displayed on the screen. The machine’s main work table is made of stainless steel and has a blower. A paper ejection function is included for ease of use. Technical data: Cutting length 721 mm Infeed height 80 mm Infeed depth 720 mm Front table depth 530 mm Minimum final offcut 20 mm Minimum final offcut with beam guard in place 90 mm Power supply 400 V / 50 Hz 1.5 kW Weight 588 kg Dimensions 1335 x 1305 x 1540 mm Key features: Electromechanical knife drive, Hydraulic clamp, Fully adjustable cutting force (250-2000 kg), Optical cutting line indicator (Laser), Air table (on front and rear tables), Pedal for pre-marking the cutting line, Front table made of chrome-nickel steel, Blade made of high-quality HSS steel, Safety features ensured by: safety curtains – photocells transparent safety cover on the rear table Gkjdpfx Akjztz Elj Uob safe drive – IDEAL patent two-handed, electronically controlled cutting start automatic knife return from any position main switch equipped with a key switch knife replacement possible with the blade permanently covered

Condition: good (used), Ideal 5222 Digicut Hydraulic Guillotine The machine is 100% functional and has been serviced. This model has the most extensive equipment. The machine was purchased from a government office. Technical specifications: Working width: 520mm Stack height: 80mm Minimum remnant: 22mm Maximum distance from the saddle to the knife: 520mm 230V power supply Gksdpezt H Tzofx Ak Usb Key features: The machine has a full EP programmer with the ability to save individual steps to memory. Hydraulic pressure beam drive, fully adjustable pressure from 200-1100N Electromechanical knife and saddle drive Automatic pressure synchronized with the knife’s cutting movement Electronically controlled saddle adjustment knob with adjustable speed Side tables Photocells „SCS” safety system, including: Electronically controlled two-handed cutting start Automatic knife return from any position Transparent cover on the rear table Laser cutting indicator Additional equipment includes: spare knife, cutting sticks, tool kit, paper stack tapping device, safe knife change device, and documentation.

Condition: good (used), Year of construction: 1991, pressure 300 t chamfer lenght 4100 mm distance between columns 3710 mm stroke - stepless adjustable 250 mm column arm 330 mm dayligth 500 mm table height 940 mm table width 250 mm working feed 7.0 mm/sec return speed 90.0 mm/sec Control konv. operating pressure max. 305 bar voltage 380 V total power requirement 22.5 kW weight 25200 kg range L-W-H 4320 x 2100 x 3370 mm well-maintained condition (!!) - in checked condition - machine video - ?v=rPOBwTfVReo Equipment: - simple, conventional hydraulic press brake - swiveling control panel, left front - electro-motoric back stop (X axis) * adjustment via front control panel (button) * with analog position display * fine adjustment via handwheel, front - with 3x stop fingers, manually adjustable - electro-motoric depth adjustment (Y1+Y2 axis) * with analog position display - 1x split set of 85° deer foot upper tool Gkjdpfoxab I Tex Ak Ueb - 1x MultiV - universal die block, with several V-openings - 2x front, stable support arms - 1x freely movable double foot switch - 1x freely movable 2-hand control - side safety device (swivelling doors) - rear safety device (sliding door) - original operating instructions

Condition: reconditioned (used), Installed, among others, in Hawema, Saacke, Deckel, Reinecker, and Strausak machines. Various versions in stock. Exchange part, inspected, tested, with a 12-month warranty. Gsdpfsy D Dvdox Ak Uskb Immediately available. Data transfer is possible if the old unit or the data set is provided in advance. This means you only need to install the device. Various sizes in stock. Return of the old part is required.