Used Residual Ozone Destroyer for sale (875)

Condition: used, Year of construction: 2007, Prominent water treatment plant, consisting of: 1. Softening: The raw water is fed into the double softener. Only one bottle is ever in operation and the other is in regeneration or stand-by. In the softener, calcium and magnesium are replaced by sodium. The system has a volume counter that switches to the other bottle when the preset quantity is reached. Regeneration takes place with saline solution from the brine tank. The value at the outlet is 0°dH. 2. reverse osmosis: Reverse osmosis fills the permeate tank with demineralised water, so-called permeate. Depending on the raw water quality, water temperature, condition of the membrane and correct setting, different conductance values and operating pressures result. The following flow rates are set during commissioning: Permeate 600 l/h, concentrate 200 l/h, corresponding to a yield of 75%. 3. permeate tank and ozonisation: The unpressurised 500 l permeate tank has an adjustable level control. For treatment with ozone, the water in the permeate tank is circulated via an adjustable ozone feed point. The ozone is generated from air in the ozone generation system by means of a silent electrical discharge and is available as an ozone-air mixture. The air and the undissolved ozone rise upwards in the permeate tank and are discharged via the residual ozone destroyer. A redox potential and ozone measurement is carried out after the centrifugal pump for monitoring purposes. The ozone dosage is set via the touch panel. You can choose between regulation via the redox potential or the ozone concentration. Gjdpfx Asw Uvdgengeuh Additional title: Water softening, reverse osmosis system, ozone sterilisation Permeate output: 600 l/h Concentrate output: 200 l/h Ozone output: 5 g/h Max. working pressure: 16 bar Current: 2 A Voltage: 230 V Frequency: 50 Hz Water: < 5 bar (cooling water) Compressed air: 5,5 - 6,5 bar (max. 10 bar); max. 0,37 Nm³/h Operation / Control: Simatic S7-300, Touch Panel Position: free standing Base construction: Fully mounted on tubular frame with spherical feet Features: Reverse osmosis unit, reaction tank complete with residual ozone destroyer, ozone generator, ozone gas warning device, ozone and redox sensor, switch cabinets with control unit

Condition: used, Year of construction: 2019, functionality: fully functional, color: other, Wood shredder in good condition. Immediately ready for use. The shredder was purchased from a bankruptcy estate and is now available for resale. Guedpfoz R I S Hex Angsh Approximate dimensions: 110/240/285 cm, year of manufacture 2019.

Condition: used, Year of construction: 1989, functionality: fully functional, machine/vehicle number: 89A 2664, power: 18.5 kW (25.15 HP), overall weight: 1,950 kg, fuel type: electric, loading space volume: 1.6 m³, loading space width: 800 mm, loading space length: 1,000 mm, loading space height: 2,000 mm, Description For sale is a robust ZENO wood waste shredder / single-shaft shredder, type ZTLL 800 × 1000, manufactured in 1989. The machine is in good working order and was used in a wood processing facility. The shredder features an 18.5 kW main drive and a hydraulic pusher floor. The feed hopper measures 1,000 × 800 mm, and the height is approximately 2,000 mm. The rotor diameter is approximately 300 mm (type-specific), and the rotor speed is approximately 140 rpm. The machine weight is approximately 1,950 kg (type-specific). The rotor is equipped with cutting plates / individual teeth mounted on tool holders. The blades or cutting teeth are in good used condition. The rotor also shows a well-maintained condition with no significant damage visible in the provided images. It is fitted with a sturdy, reinforced perforated screen basket with a 20 mm hole diameter. The perforated screen is in very good condition. The 20 mm screening is suitable for producing a correspondingly fine, uniform shredded material. The complete electrical control system, including the control cabinet, is included in the scope of delivery. This includes, among other things, a main switch, system on/off, operating and fault indicators, forward/reverse, and control for the hydraulic pump. The control cabinet is fully present and will be sold together with the machine. The offer also includes a powerful transport fan for pneumatic transport of the shredded material. The fan motor has 18.5 kW / 25 hp, 380/660 V, 36.5/21 A, 1,455 rpm, 50 Hz, cos φ 0.86, and protection class IP54. The motor weight is 136 kg. Existing pipes and fittings belonging to the system can be taken over after inspection. This means that not only the shredder itself is offered, but a largely complete combination of wood waste shredding, control, and pneumatic material transport. The machine is particularly suitable for wood waste and production residues from carpentry shops, interior design, timber construction, joineries, and comparable wood processing companies. Gjdpfez Ikz Aex Angeuh Inspections are possible by appointment. The location of the system is 3608 Thun, Switzerland. Sale from the location. Dismantling, loading, and transport, as well as any export and customs costs, are the responsibility of the buyer, unless otherwise agreed in writing. The machine is sold in its existing used condition as inspected. Technical specifications are provided to the best of our knowledge; errors and prior sale are reserved. Selling price: 12,500.00 EUR Price net, plus any applicable statutory taxes and duties. Export, customs clearance, and import duties are the responsibility of the buyer. Technical specifications in brief Manufacturer: ZENO Zerkleinerungsmaschinenbau Norken GmbH · Type: ZTLL 800 × 1000 · Year of manufacture: 1989 · Machine No.: 89A 2664 · Feed hopper: 1,000 × 800 mm · Height: approx. 2,000 mm · Main drive: 18.5 kW · hydraulic pusher floor · Perforated screen: Ø 20 mm, very good condition · Blades/cutting teeth: good condition · Rotor diameter: approx. 300 mm* · Rotor speed: approx. 140 rpm* · Machine weight: approx. 1,950 kg* · complete control cabinet included · Transport fan: 18.5 kW / 25 hp. * Type-specific comparison data ZENO ZTLL 800 × 1000. The specifications and condition of the offered machine are binding.

Condition: used, Year of construction: 2018, Sander Multizon ozone generator with a rated output of 120 g of ozone per hour. Technical data according to the nameplate: - Manufacturer: Erwin Sander Elektroapparatbau GmbH - Machine: Multizon ozone generator, 120 g/h - Type: - Machine no.: 2582 - Year of manufacture: 2018 - Rated output: 120 g ozone/h Gusdpfx Anez Ri S Tsgjh - Ozone concentration: 20 g ozone/m³ - Permissible operating pressure: -0.05 bar - Air flow rate: 6.0 m³/h - Electrical connection: 400 V – N – PE, 50 Hz - Power requirement: 12 kVA (excluding injector pump) - Current consumption: L1 13 A; L2 5.4 A; L3 10 A - Weight: 330 kg - CE marking

Year of construction: 2012, operating hours: 4,000 h, condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 363/15862010, The rotary bed dryer WB-T (model 1.00 / 3.00) from Allgaier Process Technology GmbH is a specialized industrial plant for the continuous, uniform, and gentle drying of bulk materials and biomass. In process engineering, the model designation (1.00 / 3.00) typically refers to the dimensions of the drying area, i.e., a bed width of 1.00 meter and a bed length of 3.00 meters. The heating capacity is 250 kW and is powered by electricity. Typical applications: • Biofuels & wood industry: Drying of wood chips, sawdust, and bark for pellet production. • Waste management Gsdpfx Ansz Rz Dnogjuh • Agricultural & recycling industry: Processing of fermentation residues (from biogas plants), green waste, sugar beet pulp, or bagasse. Operating principle: The technology combines the process engineering advantages of a drum dryer with those of a fluidized bed dryer: • Rotary bed mechanism: The wet product lies inside on a perforated flow bed (perforated sheet). A targeted mechanical movement or tumbling in combination with the airflow creates a rotating or rolling product movement ("rotary bed"). • Counter-current or cross-current ventilation: The drying air is blown from below through the sieve bed and flows intensively through the tumbling product. This ensures an optimal heat and mass exchange. Main features & advantages: • Low-temperature drying: The plant is ideally designed for operation with waste heat or low-temperature heat sources (e.g., from combined heat and power plants/CHP or industrial residual energy). • Long residence time: This enables particularly gentle dewatering of the material while simultaneously ensuring high homogeneity of the residual moisture. • Robust particle processing: In contrast to pure fluidized beds, large, irregular, or sticky particles can also be processed economically. • Integrated screening: The flow effectively reduces fine dust and sand content during the process.

Year of construction: 2012, condition: ready for operation (used), MFK DR 426 Edge milling cutter, deburring tool, chamfering tool Compressed air connection: 6 - 10 bar Turning rest diameter: max. 3 mm steel Shearing force: at 8 bar, 450 kp Dimensions: 330 mm x 300 mm x 320 mm (L x W x H) Weight: approx. 20 kg You are welcome to visit us for a demonstration. We can also arrange cost-effective shipping for you! You will receive a proper invoice. For international customers, a net invoice can also be issued. A valid VAT identification number is required. Subject to prior sale. Visit our shop and browse our other offers. The company names and trademarks mentioned are the property of their respective owners and are used only for identification and description of the products. Gujdpjz E U Tqofx Angoh Deviations from technical data and errors in the description of the article may occur and are subject to change.

Condition: used, Year of construction: 2000, machine/vehicle number: 000909 / 2000, functionality: fully functional, power: 15 kW (20.39 HP), volume flow: 10,500 m³/h, filter area: 61.5 m², overall weight: 1,950 kg, For sale is a complete, stationary AL-KO PROFI-JET BG 2 dust extraction and filtration system for wood dust, manufactured in 2000. The system was used in a wood processing production facility and is fully equipped with a fan, automatic filter cleaning system, rotary airlock, silencer, frequency converter, control cabinet/controller, and extensive ductwork. The dust extraction system was operated inside the production hall, and the filtered return air was returned to the production area. The filter system has an H1 rating and, according to the label, is suitable for separating wood dust with a residual dust content of ≤ 0.2 mg/m³. Technical data of the filter system: Manufacturer: AL-KO THERM GmbH Type: PROFI-JET BG 2 Year of manufacture: 2000 Serial number: 000909 Volume flow rate: 10,500 m³/h Filter area: 62.5 m² Weight of filter system: approx. 1,600 kg Filtration: Surface filtration Filter cleaning: automatic compressed air cleaning Compressed air connection: max. 6.0 bar Filter elements: approx. Ø 120 mm × 2,500 mm length Height of filter housing: approx. 2,600 mm H1 wood dust rating: residual dust content ≤ 0.2 mg/m³ Dimensions: Length: approx. 2,400 mm Width: approx. 1,620 mm Gusdpfjz Ikzpsx Angjh Overall height: approx. 4,500 mm Fan: Manufacturer: JKF Industri Type: JK-40 MTD L Power: 15 kW Speed: approx. 2,900 rpm Fan year of manufacture: 2000 The installed 15 kW drive motor is rated separately with 2,920 rpm at 50 Hz and protection class IP55. Frequency control and controller: The dust extraction system is equipped with a Danfoss VLT 6000 HVAC frequency converter. Complete control cabinet with Siemens controller and Siemens TD 200 operating panel included. The automatic filter cleaning is carried out pneumatically via individually controlled valves. Rotary airlock: Manufacturer: AL-KO Type: ZRS 960 Rotary valve: Ø 320 mm Number of vanes: 7 Inlet: 250 × 960 mm Outlet: 208 × 960 mm Delivery rate: 47,450 l/h Motor power: 0.55 kW Speed: 12 rpm Protection class: IP54 Additional equipment: Included with the system: - Silencer, connection Ø 400 mm - Return air ducting to the production hall - Complete system control - Danfoss frequency converter - Automatic pneumatic filter cleaning - Rotary airlock - Extensive galvanized dust extraction and return air ducting Large parts of the existing ductwork can be taken over after consultation. The system is still in its assembled condition. This allows the layout, duct routing, and existing components to be inspected and documented before purchase. Location / Sale: Location: 3608 Thun, Switzerland Available: immediately Dismantling no later than: 07/31/2027 The system will be sold in its currently assembled condition. Dismantling, removal, loading, and transportation will be carried out entirely by the buyer at their own expense and responsibility. In the event of a sale to a foreign country, transportation, export/import, and customs duties will also be borne by the buyer. Inspection possible by appointment. Sold as is, without warranty. Selling price: 12,500.00 EUR Price net, any applicable taxes and duties will be added. Export, customs duties and import duties are the responsibility of the buyer.

Condition: ready for operation (used), Year of construction: 2021, A stationary Brabender residual moisture and moisture content measuring device is offered. Relative measuring range: 0.0001%H₂O-15%H₂O, absolute measuring range: 0.01mgH₂O-15mgH₂O, moisture content resolution: 0.01mg, resolution: 1ppm, relative resolution: 0.0001%H₂O, measuring temperature range: 30°C-160°C, temperature setting: in 1°C increments, sample weight: approx. 0.05g-20g, max. sample volume: approx. 50cm³, accuracy: better than approx. 0.6mg, ambient temperature: +10°C to +45°C, relative humidity: 5%-95%, storage temperature: -20°C to +55°C, relative humidity: 5%-95%, measuring distance: approx. 1m, measuring height: approx. 1.6m. Dimensions X/Y/Z: 562mm/420mm/275mm, weight: 27.6kg. Documentation available. Inspection possible by appointment. Gjdpjzli Urofx Angouh

Condition: excellent (used), Year of construction: 2020, Pallmann PS-H 600/900 plastic shredding line. Mill chamber dimensions 600x900mm, power 75/90kW. Very good condition. Line components: 1. Conveyor, Keiper product Drive power 1.1 kW Belt working width 600 mm Center distance 5500 mm 2. Surface metal detector, type FS 650, manufacturer Sesotec Detection width 640 mm Detection sensitivity for FE ball at detection height of 20 mm: 2.5 mm Detection sensitivity for FE nut at detection height of 100 mm: M6 3. Cutting mill, PS-H 600x900 F3/SD5, PALLMANN product 4. Volumetric feeder, type RVR 10, WAM product Drive power 0.75 kW 5. Screw conveyor, type TME219/0440, WAM product Drive power 2.2 kW 6. Sifter, type R25, Waltinger manufacturer Drive power 1.5 kW 7. Fan, type MXE063-008030-00, Reitz product Flow rate: 80 m3/min Total pressure increase 630 daPa Drive power 15 kW Rotational speed 3,000 rpm 8. Filter, type PA 7x8-2500, Tama product Residual dust content: < 20 mg/m3 Filter area 54 m2 Exhaust air 4800 m3/h 9. Filter, type PA 6x5-2000 CCD, Tama product Residual dust content: < 20 mg/m3 Filter area 23 m2 Exhaust air 2100 m3/h 10. Fan, type MXE031-003530-00, Reitz product Flow rate: 35 m3/min Total pressure increase 315 daPa Drive power 3 kW Rotational speed 3,000 rpm 11. Metal separator, type Rapid Vario FS 100, Sesotec product Removal duration (adjustable) 0.5-29 s Compressed air connection (hose) 6/8 mm Working pressure 5-8 bar Guodszxup Ijpfx Angjh 12. Screw conveyor, type TMS219/0540, WAM product Drive power 2.2 kW

Condition: used, functionality: fully functional, Year of construction: 1994, Residual concrete recycling plant Feeding with screw conveyor Pumps Gujdpfx Asywn U Rengsh Agitators

Condition: excellent (used), Year of construction: 2022, operating hours: 1,000 h, functionality: fully functional, machine/vehicle number: SN210551, overall weight: 14,000 kg, type of input current: AC, input voltage: 400 V, power: 400 kW (543.85 HP), Equipment: type plate available, A MIXACO heating/cooling mixer is a combined system consisting of a heating mixer and a downstream cooling mixer, specifically designed for the processing of powders, granules, and compounds (e.g., PVC dry blends, WPC, or masterbatches). Technical specifications – summary (details can be found in the documents): Hot mixer: • Volume: 3500 liters – Usable volume: 2500 liters • Tip speed: 5-50 m/s • Made of duplex steel – 1.4462 stainless steel • Power drive with 400 kW FC controlled • Vacuum up to 150 mbar abs. Gjdpfez Iww Rox Angouh Cold mixer: • Volume: 9000 liters – Usable volume: 7650 liters • Tip speed: 3.5 – 7 m/s • Made of 1.4541 stainless steel • Power drive with 90 kW FC controlled The operating principle is divided into two physically and apparatus-wise separate process phases: 1. The heating mixer phase (heating and homogenizing) • Mechanical friction: In the heating mixer, a modular mixing tool rotates at a high circumferential speed (approx. 10–40 m/s). The intense flow and vortex formation (mixing vortex) causes the particles of the mixture to rub intensely against each other. • Heating: This mechanical friction generates the necessary thermal energy directly in the product, quickly and evenly heating the material to the desired target temperature (sometimes exceeding 100 °C). • Recipe component addition: At the same time, all recipe components, such as additives, dyes, or liquids, are perfectly homogeneously distributed. An integrated aspiration system also ensures the dehumidification of the mixture. 2. The transfer • Once the target temperature defined in the process program is reached, a contoured, dead-space-free outlet opens on the heating mixer. • The hot, homogeneous mixture is transferred with minimal residue and quickly to the cooling mixer, which is located directly below or next to it. The heating mixer is then immediately available for the next batch. 3. The cooling mixer phase (gentle cooling) • Heat exchange: In the cooling mixer (available in vertical or horizontal design), the hot material is passed over cooled surfaces. • Water cooling: A targeted cooling water circuit in the double jacket (bottom and side walls) efficiently removes thermal energy from the dry blend. • Agglomeration prevention: A slow, material-friendly stirring mechanism keeps the mixture in motion until the final storage temperature is reached. This prevents caking (compaction) due to residual heat before the material is transferred to silos or further processing. Summary created with AI. The units can be inspected in operation in the Netherlands. The system for sale was used in the R&D center of UBQ for development purposes. This explains the very good condition for the low number of production hours. We also have a steel structure available for the setup. This is not included in the price. If there is interest, it can be negotiated separately. Currently, the system is located outside of Europe – we need to determine whether direct transport is feasible or whether import to Europe by UBQ is more sensible (which would allow for a sale within Europe with a reverse-charge mechanism).

Condition: used, mileage: 249,000 km, power: 120 kW (163.15 HP), first registration: 07/2016, fuel type: diesel, overall weight: 3,500 kg, color: white, gearing type: mechanical, emission class: euro6, number of seats: 9, total length: 6,961 mm, total width: 1,993 mm, total height: 2,612 mm, Year of construction: 2016, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), parking heater, soot filter, For sale is a well-maintained Mercedes-Benz Sprinter 316 MAXI with the popular 2.1-liter diesel engine. * The vehicle is in good condition! * German vehicle * Euro 6 standard * First owner * Complete service history * M1 passenger car registration Equipment: MAXI version * Combination version * 7 seats (up to 9 seats possible) * Air conditioning front + rear * Auxiliary heater * Passenger airbag * Electric step * Heated exterior mirrors * Electric exterior mirrors * Electric windows * Central locking * and more... Why we are the right choice? Attractive financing through our partner bank. * Nationwide delivery of your desired vehicle * Trade-in of your old vehicle at fair prices * Transfer license plate (5-day/customs registration) usually on the same day * Pick-up service from the airport or train station All vehicles are professionally detailed and hygienically clean! The special features: Disinfection of the interior and ventilation system using ozone cleaning. 2-stage polishing on the exterior Guodpfjz R Ibyex Angoh * if necessary, paint correction and smart repair All of our vehicles have also undergone a thorough maintenance service. Of course, this includes new fluids, filters and other expenses that you shouldn't have to worry about. Optionally, we can have the vehicle inspected at an independent testing center or workshop of your choice. We are pleased to have aroused your interest and are available to you around the clock. If you have any questions, comments or special requests, please do not hesitate to contact us! More information and insights into our business philosophy can be found at Special equipment: Ashtray in the passenger compartment, Equipment package: Cabin Comfort, Audio system Audio 15 (radio with color display), Two-way speakers front and rear, Folding cover for storage compartment, Interior trim in the cargo/passenger compartment Luxury, Auxiliary heater (hot water), Remote control for auxiliary heater, Roof control unit with reading light driver/passenger side, Non-woven battery 95 Ah, Outside temperature display, Master key in addition, Heated rear window, Rear door (opening angle 270 degrees), Steering wheel with multifunction incl. trip computer, Parameterizable special module, Spare wheel in driving condition, Spare wheel holder under frame end incl. jack, Interior mirror, Mud flaps rear, Mud flaps front, Seat equipment: Comfort headrest, Driver's seat, Stabilizer rear, Stabilizer front reinforced, Start/Stop system engine, Fuel gauge for auxiliary heater, Step rear door, Front axle reinforced, Additional heater Additional equipment: 3rd brake light, Storage: Luggage net on rear doors, Storage net on front seat backrest left, Storage net on front seat backrest right, Adaptive brake light, Airbag passenger side, Airbag driver side, Display for windshield washer fluid level, Exterior mirrors electrically adjustable and heated, both, Exterior mirrors with integrated turn signal, Floor assembly combination version, Braking system with ABS+ASR, Roof lining, Roof lining in the driver's cab, Window for rear doors, Window for rear doors/tailgate with wiper/washer system, Rear window wiper, Window in cargo/passenger compartment: - fixed, rear left, Window in cargo/passenger compartment: - fixed, rear right, Window in cargo/passenger compartment: - fixed, middle left, Window in cargo/passenger compartment: - fixed, mi

Year of construction: 2018, condition: ready for operation (used), Industrial fan Forklift passage for transport Flow rate: 70,000 m3/h at 1,490 rpm Gsdpfx Ansz Rv T Degouh Pressure: 1000 Pa (for a flow rate of 70,000 m3/h) Thrust: 1200 N Ejection speed: 29 m/s Power supply: 400 V three-phase Power: 37 kW / 69 A Starting: 50 kVA with residual current circuit breaker > 100 mA Dimensions: 4100 x 1465 x 1550 mm Weight: 650 kg Duct diameter: Ø 1000 mm Sound level at 1, 3, and 5 m: 93 dB(A), 90 dB(A), and 87 dB(A) 2 units for sale Available immediately

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, total height: 2,000 mm, total length: 1,600 mm, total width: 1,600 mm, type of input current: three-phase, controller manufacturer: Union Dialog electronic control, compressed air connection: 6 bar, water pressure: 2 bar, Used 2018 Union MDMV 1 closed-circuit vacuum solvent degreaser, 50kg basket, Dialog control, Industrial Frigo chiller and 2 Safechem units. Manufacturer: Union Model: MDMV 1 Machine Type: Closed-circuit vacuum solvent metal degreasing / component cleaning machine Year: 2018 Condition: Excellent Includes: Industrial Frigo GR2A 30/Z industrial water chiller & 2 x SAFECHEM SAFE-TAINER chemical storage/handling units Machine Description Used 2018 Union MDMV 1 industrial metal degreasing and component cleaning machine, designed for precision cleaning of small and complex metal components using super-stabilised perchloroethylene (PCE / PER / tetrachloroethylene). This is a closed-circuit hermetic vacuum solvent cleaning system incorporating washing, rinsing, vapour degreasing, solvent recovery/distillation and vacuum drying within an enclosed process. Technical Specifications Maximum Basket Capacity: 50 kg Solvent Type: Perchloroethylene / PCE / PER / Tetrachloroethylene – C₂Cl₄ Solvent Load: Approx. 397 kg / 248 litres Main Electrical Supply: 400 V / 3 Phase / 50 Hz Installed Power: Approx. 23 kW Rated Current: Approx. 46 A Steam Pressure Requirement: Approx. 4–5 bar Compressed Air Requirement: Approx. 6–8 bar Water Pressure Requirement: Approx. 2–3 bar Floor / Ground Loading: Approx. 549 kg/m² Control: Union Dialog electronic control This particular machine also has a substantial integrated solvent-management system incorporating working and recovery tanks, solvent pump, fine filtration, swarf filtration, still/distillation system, condenser, heat exchanger, separator, decanter, vacuum pump and active-carbon treatment. Continuous Solvent Recovery A particularly useful feature of the MDMV design is the continuous solvent distillation/recovery system. Union states that MDMV machines operate under vacuum for rapid washing cycles and use continuous vacuum distillation with automatic final stripping of residues, allowing contaminated solvent to be regenerated and reused during production. Industrial Frigo GR2A 30/Z Chiller Included The machine is supplied with a 2018 Industrial Frigo GR2A 30/Z air-cooled industrial water chiller. Refrigerant: R407C Refrigerant Charge: Approx. 5 kg Electrical Supply: 400 V / 3 Phase / 50 Hz Rated Current: Approx. 23 A Nominal Water Pressure: Approx. 3.2 bar Temperature Set-Point Range: -10°C to +25°C Weight: Approx. 390 kg The complete installation includes: 2018 Union MDMV 1 metal degreasing machine 50 kg maximum basket capacity Union Dialog control Closed-circuit solvent cleaning system Vacuum cleaning/drying system Rotating / oscillating basket system Spray cleaning capability Immersion cleaning capability Solvent vapour degreasing Integral solvent distillation and recovery Working solvent tank Recovered-solvent / waiting tank Solvent circulation pump Fine solvent filtration Swarf filtration Gujdpfx Anjz Itlwsgoh Vacuum pump Condenser Heat exchanger Water / solvent separation Decanter Active-carbon vapour treatment system Floor safety / spill-containment tank 2018 Industrial Frigo GR2A 30/Z industrial chiller 2 x SAFECHEM SAFE-TAINER chemical handling/storage units Stainless steel containment trays Use and maintenance handbook Electrical documentation Please Note: All specifications, dimensions, capacities and descriptions are approximate and provided in good faith.

Condition: good (used), Year of construction: 2011, operating hours: 10,337 h, overall weight: 3,830 kg, ALMiG Gear 132 Compressor, Screw Compressor, 10 bar The screw compressors of the GEAR series are particularly suitable for very high compressed air requirements. The maintenance- and service-friendly drive concept of the GEAR compressors includes a robust drive motor with high power reserves. The highly efficient gearbox operates with minimal slippage, high operational reliability, and an efficiency of over 98%, resulting in almost lossless operation and thus protecting the drive. Furthermore, the highly efficient coolant separation enables a minimal residual oil content of only 2–3 mg/m³. The encapsulated design of the gearbox makes these systems ideal for use under the harshest operating conditions. Ideal for very high compressed air demands Robust drive unit with high power reserves Almost lossless concept with an efficiency of > 98% Maintenance- and service-friendly drive concept ALMiG Gear 132 Year of manufacture: 2011 Final pressure: 10 bar Motor power: 132 kW Volume flow: 18.04 m³/min Length: 2800 mm Width: 1400 mm Height: 2025 mm Gjdpettv Ibjfx Angsuh Weight: 3830 kg Operating hours: 10,337 h Load hours: 9,378 h Downtime: 13,887 h Total delivered volume: 11,333,000 m³ You can find more ALMiG compressors – new and used – in our shop! International shipping costs available upon request!

Condition: used, Year of construction: 2022, functionality: fully functional, For sale, starting from our location in 45888 Gelsenkirchen, are two Inject Star P-60 residual meat recovery systems, including bone crushers and accessories. Guodpfx Anez Iz Tcegsh These systems are used, manufactured in 2019 and 2022, and come from a business liquidation. Currently, both systems are still operational and can be inspected on-site by appointment. Disassembly, loading, and transport are the responsibility of the buyer.

Condition: ready for operation (used), Year of construction: 2018, functionality: fully functional, RUF 500 Briquetting Press including SMIPACK BP800 Packaging Machine For sale is a hydraulic briquetting press, RUF 500, including a SMIPACK BP800 packaging machine. The press is suitable for compacting wood chips, sawdust, and comparable dry biomass residues. The briquetting press is from April 2018 and is in very good condition. According to the machine display, it has only approximately 34.8 operating hours. This combination is aimed at wood processing companies, sawmills, carpentry shops, as well as recycling and biomass companies that want to process their residual materials into briquettes and then package them. Technical data of the RUF 500 Manufacturer: RUF Maschinenbau GmbH & Co. KG Type: RUF 500 Machine number: 2742 Year of manufacture: 04/2018 Operating hours according to display: approx. 34.8 Voltage: 400 V Rated current: 52 A Frequency: 50 Hz Motor power: 22 kW Throughput: up to approx. 485 kg/h, depending on material and bulk density Briquette dimensions: approx. 150 × 60 mm Maximum pressing pressure: approx. 1,700 kg/cm² Machine weight: approx. 3,800 kg Gsdpfsz Dfcasx Angeuh Dimensions: approx. 2,900 × 2,000 × 2,100 mm Pressing process: hydraulic briquetting Control: Siemens SIMATIC HMI with touchscreen Suitable materials Wood chips, sawdust, planing shavings, shredded biomass, and comparable dry residues. Scope of supply Hydraulic briquetting press RUF 500 Packaging machine SMIPACK BP800 An inspection and test run are possible by arrangement. Package price including SMIPACK BP800: 55,000 € plus VAT.

Condition: good (used), Year of construction: 1997, Residual oxygen measuring device for checking the gas volume in insulating glass. Dimensions: Depth: 270 mm Width: 204 mm Gsdpfx Anei Azc Ajgsuh Height: 180 mm Weight: 5.7 kg

Condition: ready for operation (used), Year of construction: 2022, spindle motor power: 29,000 W, spindle speed (max.): 5,000 rpm, travel distance X-axis: 530 mm, travel distance Y-axis: 120 mm, travel distance Z-axis: 1,215 mm, overall weight: 620 kg, controller manufacturer: SIEMENS, controller model: Sinumerik ONE, number of slots in tool magazine: 40, number of axes: 6, This 6-axis EMCO Hyperturn 65 Powermill G2 was manufactured in 2022. A highly productive CNC turn-mill center, it features a main spindle and subspindle both with a max torque of 250 Nm and speeds up to 5000 rpm. The milling spindle offers up to 12000 rpm. Includes a 40-position tool magazine, 12-position turret, and advanced Sinumerik ONE control system. If you are looking to get high-quality turning and milling capabilities consider the EMCO Hyperturn 65 Powermill G2 machine we have for sale. Contact us for more information. • Main spindle (direct drive): • Max. torque: 250 Nm • Subspindle (direct drive): • Max. drive power: 29 kN (as provided) • Max. torque: 250 Nm • Speed range: 0–5000 rpm • Milling spindle (direct drive): • Max. drive power: 37 kW • Max. torque: 30 Nm • Speed range: 0–12000 rpm • Tool turret (direct drive): • Max. drive power: 10 kW • Max. torque: 30 Nm • Speed range: 0–12000 rpm • Kinematics and axes: • Cross slide at the top with turning/milling spindle as motor spindle; hydraulic clamping during turning • Y-axis travel: +/- 120 mm • B-axis with direct drive: +/- 120°, hydraulic clamping • Tooling: • 40-position tool magazine, HSK-T63 • 12-position radial turret with direct drive, BMT55P tool interface • Spindles and clamping: • High-clamping cylinder with draw tube for main spindle • Full clamping cylinder with partial hollow clamping 66 x 550 mm deep in counter spindle • Programmable clamping pressure for main and counter spindle • External feed flushing on main and counter spindle • Mechanical holding brake on main and counter spindle • C-axis for main and counter spindle • Control and HMI: • SINUMERIK ONE / OPERATE, EMCONNECT app-based UI • 22" multi-touch display • IPC with 240 GB • SHOPTURN dialog programming • 3D simulation and Drawing • Residual material detection Gujdex D E Hbjpfx Angoh • Unblocking from external memory • CAD reader (DXF import) • TRANSMIT and TRACYL for C-axis programming • USB interface, Network drive (Ethernet) • PC keyboard incl. HMI hotkey • LED status bar • Fluids and utilities: • 2 coolant lines at 25 bar • 2 flushing pumps at 4.3 bar • Control cabinet air conditioning unit • Cooling system for spindle motors, milling spindle, B-axis torque motor, and turret direct drive • Hydraulic unit • Machine light • 8 leveling elements • Feedback/measurement: • Glass scales: X1 (incl. air system), Y1, Z1, X2 (HT65-PM-G2 / 840D-sl) Additional equipment • Chip management and filtration: • Hinged belt chip conveyor, discharge height 1200 mm • Belt filter system, 980 liters • Dirty water pump • Control/monitoring options: • BAOD-SL electronic handwheel (portable, magnetic mount for Siemens controllers) • EMCO tool breakage and wear monitoring / B40D-SL • Wireless probe / HSK drill breakage control BK-MICRO • 4-axis turning / balance cutting (SINUMERIK option) • Alternative-end spindle speed (SINUMERIK option) • Turret as tailstock (SINUMERIK option) • Counter spindle as tailstock (SINUMERIK option) • Bar feeder (specifications as provided): • Bar length: 300–1200 mm • Bar diameter: 10–104 mm • Material support surface (front view): 800 x 1250 mm • Material capacity: 12 bars with 65 mm diameter • Max. load capacity: 400 kg (max. 74 kg/bar) • Rectangular material: min. edge length 6 mm; max. circumference 105 mm • Hexagonal material: SW 5 to 85 mm • Round material:

Condition: like new (used), Year of construction: 2020, operating hours: 5,600 h, functionality: fully functional, machine/vehicle number: 0-250-77-3262, 1. BASIC MACHINE - rigid steel frame construction - 2 workpiece clamping devices with integrated stop system - Separate adjustment of the clamping devices via rack and pinion gear in X-direction - Digital AC servomotors - The position of the clamping devices at the workpiece is program-controlled - Adjustment of the clamping devices between the separate processing steps in the processing area is possible. - Automatic measuring of the workpiece thickness and lengths by the clamps and the stop system - Blowing nozzle for safe removal of residual parts off the clamps 1.1 LOWER PROCESSING SUPPORT - Rigid aluminium cast construction - Integrated threefold divided table with selectable air cushion - Lateral stop system - Adjustment of the axes in Y- and Z-direction - Ball bearing spindle (Z-direction) and rack and pinion gear (Y-direction) - Digital AC servomotors - Suitable for fitting of various configurations 1.2 UPPER PROCESSING SUPPORT - Rigid aluminium cast construction - Integrated threefold divided pressure beam with selectable air cushion - Adjustment of the axes in Y- and Z-direction - Ball bearing spindle (Z-direction) and rack and pinion gear (Y-direction) - Digital AC servomotors - Suitable for fitting of various configurations 1.3 WORKPIECE DIMENSIONS workpiece length: min. 200 mm workpiece length: max. 2500 mm workpiece width: min. 70 mm workpiece width: max. 1000 mm - with restrictions in processing: 1300 mm workpiece thickness: min. 8 mm (2 x 4 mm) workpiece thickness: max. 80 mm (2 x 40mm) workpiece stacking: max. 2 pieces - same workpiece dimensions Note: - Workpieces must have a straight edge at the reference edge - Max. curve tolerance: +/- 0.5 mm for a work- piece length = 2000 mm - The workpiece length/width ratio should be >=1. The longer edge of the workpiece should be placed on the machine. - Warped workpieces (>= 0.3 mm) lead to a higher rate of processing tolerances and wear at the workpiece tables - Due to the chips no stackable workpieces can Gjdpfx Anoz Df Txjgsuh be guaranteed for router processings. - An external cleaning or extraction in the outfeed area is recommended. - For through holes of double parts the drilling quality depends on the workpiece material and the tool as well as on the feeding speed profile and the rotation speed of the drilling spindle. Thus, however, efficiency could possibly be reduced. 1.4 WORKPIECE FEEDING AREA - Air cushion table in rigid frame construction - Surface from Hornit board - integrated fan 1.5 WORKPIECE REMOVAL AREA - Cross belt conveyor in rigid frame construction - 8 transport belts, frequency-controlled drive - 8 electro-pneumatic controlled disengaging device 2. CE SAFETY AND PROTECTION DEVICES - Safety fences in the lateral and rear area - Safety mats in the feeding area 3. ENVIRONMENTAL CONDITIONS - prescribed environmental temperature: + 5 degrees up to + 40° C (in case of environmental temperature >35°C or air humidity >65% a cooling unit for switch cabinet is recommended) 4. ENERGY SAVING MODE - ecoPlus button for starting stand-by operation. The button can be activated during processing. This will have the following impacts after the end of the program: - Primary power of drives will be switched

Condition: good (used), Year of construction: 1998, Measuring device for checking the gas volume in insulating glass. Width: 204 mm Height: 180 mm Gjdpfx Ajyll H Eongouh Depth: 270 mm Weight: 5.7 kg

Condition: used, Year of construction: 2020, x-travel 762 mm y-travel 508 mm z-travel 610 mm control MAX5 Hurco distance spindle nose and table 152 - 762 mm speed mainspindle max. 12.000 U/min power capacity - main spindel 13,4 kW max. Torque 214 Nm tool taper SK 40 DIN 69871 A table surface area 1.020 x 510 mm max. table load 1.500 kg T-slots 5 x 18 x 100 mm number of toolpositions 30 pos. tool taper SK 40 tool diameter max. 80 / 76 mm tool length - max. 300 mm weight of tools max. 7 kg rapid traverse X-axis 38 m/min rapid traverse Y-axis 38 m/min rapid traverse Z-axis 32 m/min total power requirement 24 kVA weight of the machine ca. 5,1 t dimensions of the machine ca. 4,0 x 4,1 x 2,8 m Gujdpfxjz I T Rts Angjh CNC-Machining Center Vertical HURCO - VMX 30i - Year 2020 / Commissioning 2025 - only approx. 500 operating hours - Adaptipath Trochoidal milling for higher metal removal rates, controlled step-over, and residual material detection - Simulation graphics - Tool and material library - Pocket milling with islands - Synchronous tapping (Tapping without a compensating holder) - incl. 15x high-clamping force chucks BDV40-HMC20S-85 - incl. 3x tapping chucks BDV40-MGT6-80 - incl. mechanical centering vise BSM 250 - incl. 1x set of quick-change hardened grip jaws with grip strip - incl. various tap holders - incl. various drill bits and reducing sleeves

Year of construction: 2000, condition: good (used), Residual Oxygen Meter for checking the gas content in insulating glass. Gjdpoht Evpefx Angjuh Dimension: Width: 245mm, depth: 185mm, height: 95mm, Weight: about 3kg

Condition: used, functionality: fully functional, overall weight: 7,500 kg, total length: 14,470 mm, total width: 3,500 mm, total height: 1,509 mm, We offer this used CSM automatic tube welding system, manufactured in 2014. Our general terms and conditions apply. Payment in advance required. Gedpfxjz Hk Ere Angouh Shipping costs not included. If you have any questions or require further information, please send us a message or call us. Recommended tube diameters: 5 - 15 mm Wall thicknesses: 0.40 - 1.00 mm Using the profiling unit, a stainless steel strip from a coil is formed into a tube by passing through seven profiling stations. The continuously profiled tube is welded in the welding chamber (TIG) in a continuous process. The torch tracking system can detect and automatically correct changes in the position of the material joint relative to the arc during the welding process. A measuring wheel mounted on the continuously moving tube continuously measures its speed and records the length. A double straightening device eliminates any residual curvature of the tube during the continuous process. A flex unit continuously cuts the tube and places it on the sorting rail for tubes that meet or do not meet the quality requirements. Two deburring stations deburr the tube ends, and an automatic length measurement system measures each tube before it is placed in the box. The tube welding system is fully functional and can be inspected while in operation.

Condition: used, Year of construction: 2019, operating hours: 196 h, functionality: fully functional, machine/vehicle number: W09D013KWKAD43636, operating pressure: 500 bar, total length: 2,910 mm, high-pressure hose length: 500 mm, total height: 1,770 mm, total width: 1,720 mm, pressure: 500 bar, empty load weight: 760 kg, fuel: diesel, heating capacity: 115 kW (156.36 HP), overall weight: 760 kg, water tank capacity: 300 l, fuel tank capacity: 70 l, power: 13 kW (17.68 HP), temperature: 95 °C, volume flow: 0.9 m³/h, noise level: 104 dB, pressure (max.): 500 bar, Equipment: chassis, crane, This well-maintained DYNAJET 500th 15 HELI hot and cold water high-pressure unit is available for immediate delivery. Manufactured in 2019 and having only 196 operating hours, the machine is in excellent condition and is being delivered fully serviced, fully functional, and ready for operation. Designed for demanding industrial cleaning applications, the DYNAJET 500th 15 HELI combines powerful cleaning performance with compact dimensions, low weight, and excellent mobility. With an operating pressure of up to 500 bar and hot water temperatures up to 95°C, the machine is ideally suited for removing heavy contamination, coatings, grease, and industrial residues. The unit is equipped with a reliable Kubota diesel engine, integrated hot water system, and a large 300-litre water tank for independent operation even where external water supply is limited. The trailer-mounted design ensures maximum flexibility and easy transportation between jobsites. To ensure many years of reliable operation, the machine will be supplied with a brand-new 50 m high-pressure hose. A turbo nozzle and standard flat-jet nozzle are included in the sale. Key features and advantages: * Year of manufacture: 2019 * Only 196 operating hours * Fully serviced before delivery * Fully functional and ready for operation * Maximum operating pressure: 500 bar Gujdpfx Aez Nd Ndongoh * Flow rate: up to 15 l/min * Hot water temperature up to 95°C * Powerful Kubota 3-cylinder diesel engine * Integrated hot water system with high-performance burners * 300-litre integrated water tank * Approx. 70-litre fuel tank * Trailer-mounted unit with overrun brake * New 50 m high-pressure hose included * Turbo nozzle included * Standard nozzle included * Compact, robust and easy to transport *Ideal for industrial cleaning, surface preparation and professional service applications Please contact us if you are interested or would like to receive further information, pricing details, additional photos, or arrange a viewing of the machine. We will be pleased to assist you.