Used Push Broom for sale (1,581)

Condition: new, machine/vehicle number: 6d88bda3a1ee2464a81b34f36, empty load weight: 4 kg, maximum load weight: 13 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction, with slight pretensioning in the middle, turntable with strong ball bearing slewing ring, wheel chocks with holder, quarter-shell mudguards in front of and behind each axle Low loader lashing eyes over front axle: 2 pairs of ring lashing eyes, 5 tons each at the front on offset Ihedpfei Ri N Aex Ah Njt Lowbed: 4 pairs of lashing eyes on the side of the low bed, 6 tons each 5 pairs of lashing eyes per 5 tons between the side members Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye, mechanically adjustable in length by 6 x 100 mm and lockable (drawbar length 1 700 - 2 300 mm) Axles + suspension BPW drum brake axles, each with an axle load of 10 tons, axle adjuster. Axle endurance brake test to 105 km/h, rear axle can be removed manually. By releasing the air lock and lowering the rear to the ground. Then disconnect the connecting hoses from the rear section, insert the transport bar into one of the rear sockets and unhook the rear by gently pushing it down at the rear and pulling it back at the same time (parking brake released). After loading or unloading, drive up to the rear section and hook it in up to the mark. Then lift the rear section up to driving height and attach the connecting hoses. Confirm the pin lock. (Visually check whether the bolt engages) and check the rear function. Air suspension with lift & lower valve Wheels and tires 235 / 75 R 17.5, from leading manufacturers, steel rims in twin arrangement, factory silver Brake system 2-line compressed air brake system, spring-loaded parking brake, 2 interchangeable clutch heads at the front, with connecting lines to the motor vehicle, EBS, electronic brake system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front, 2 white/red lane departure lights at the rear, rotating beacon with holder, switched via parking light (light can be removed), 2 pairs of warning signs, double LED illuminated and extendable to 3,300 mm, removable with plug, 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 x 7-pin agricultural plug, voltage converter 12/24 volt (only for electrics, not for ABS/EBS) Floor Steel/ checker plate floor on offset, between longitudinal and cross member with perforated plate cover. Axle cover cannot be driven over, widening to 3000 or 3300 mm possible. Operating instructions Please note! A special permit is required for axle loads of 10,000 kg. The permit must be applied for individually in each federal state; the legislator does not have to give an approval for 20 tons GG. Customer risk. Special approval required if the overall length of the train exceeds 18 750 mm. Observe country-specific approval regulations. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. Observe the BO circle!!! Approval / plates Country of registration: Germany, with Dekra approval and expert opinion (according to §13 EG - FGV), prepared for single-line license plate holder, warning sign according to ECE - 70, contour marking with reflective strips according to ECE R 048 Paintwork Front frame hot-dip galvanized incl. passivation, rear frame RAL9006 silver, drawbar KTL bla

Condition: new, machine/vehicle number: c78894767223a51dd199030f3, empty load weight: 4,600 kg, Further information Frame Welded steel construction made of fine-grained steel, hot-dip galvanized, flat plateau without raised edges, Loading area slanted downwards by approx. 8° after the rear axle. Side members made of steel profiles, Hot-dip galvanized steel frame, with stainless steel plate at the kink as cable guide - flush with the floor. For trucks with Wheelbase: 2nd axle 1,795 mm / 2nd to 3rd axle 4105 mm and 3rd to 4th axle 1350 mm Trailer coupling Towing hitch ball head D24.8: (height from floor to top edge approx. 480 mm), towing capacity 2,800 kg, incl. assembly and electrics with 7-pin socket Accessories/conversions 2 holders for wheel chocks, aluminum side bumpers, foldable - are taken from the truck! Steel underride guard, quarter-shell mudguards with mud flaps - will be taken from the truck! Storage box Plastic tool box, with drawer and shelf, w=650 Incl. / h=520 / d=670 mm, lockable with a padlock (lock not included). not included) 1 holder for 3 pcs. petrol cans 1 stainless steel storage box, w=600/h=400/t=500 mm, with polished door, incl. lockable, includes control valve. lockable, includes control valve and electro-hydraulic pump unit. pump unit. Control box with circumferential door seal and sealing sleeves on the back (splash-proof according to techn. technical possibility) Electrics Adaptation of the existing rear lights, 2 additional LED work lights, recessed in the bulkhead recessed switched via parking light with switch on front wall outside in FR-left, 1 LED work light, at the rear, with integrated reversing camera Incl. with color flat screen monitor, screen with suction cup mount and power supply via 24 volts, Voltage divider 24/12V, 1 socket 7-pin 12V = plug-in adapter Base Mega Grip made of toothed galvanized grating, steel grating 50/4 Incl. with mesh width 50 mm. Top side with anti-slip serration, laid continuously over the entire main frame plateau Lashing eyes 12 pairs of lashing rings suspended freely pivoting in the outer frame - 10 tons each. 1 x at the front and the last one at the rear. 1 piece Lashing eyelet at the very rear in the middle for fastening the winch cable 12 lashing eyes centrally embedded in the floor, each 5 to. (not included in Inkl. Iedpfxok Unite Ah Noht rear slope) Front wall Sheet steel bulkhead, height 1,500 mm. Fixed with corner pillars at front wall height. Each with 2 x 12 pcs. Suspension brackets for lashing chains mounted on the left and right of the front wall Cable winch Electric cable winch, 24 volt, pulling force approx. 6350 kg, mounted in the center of the bulkhead (recessed with loading bridge), operation with radio remote control, cable length min. 35 m x 9.5 mm, with roller rope window, with cable pressure plate, incl. overload protection, cable freewheel clutch, manual switch with approx. 5 m control lever, acceptance of the cable winch, civil engineer test report, test book, operating instructions Drive-on ramps Length 3,500 mm - 2-part (2,000 mm + 1,500 mm), width 850 mm, load capacity 20,000 kg / pair (also for ramp loading), electric for ramp loading), electro-hydraulically foldable and laterally movable - incl. Electro-hydraulic pump unit. Drive-on angle approx. 8° with lowered rear axle Ramp support made of hot-dip galvanized steel grating (like the floor of the loading bridge), with with anti-skid toothing. Ramps can be pushed together to approx. 170 mm, Hydraulic ramp extension. Ramp prepared for operation on loading ramp with full load capacity. Ramp locking with 2 tension

Condition: new, machine/vehicle number: 81b04fd2e28f354df79a4c3b3, empty load weight: 3 kg, maximum load weight: 14 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235/75 r17,5``, Further information Chassis Wechel central axle trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear Folding locking adapter + height adjustment for parking height 1,000 - 1,120 mm, center supports can be folded and guide rollers can be pushed upwards, 4 container locking devices with sturdy outriggers on 20-basefor swap bodies 7.15 / 7.45 and 7.82 1 pair of gear support legs at the front, with straight lower section and single-sided operation in FR right 2 wheel chocks with holder Aluminum side bumpers Steel underride guard Half-shell mudguards Towing device central axle trailer Towbar with tested 50 mm towing eye, forwarding agent version (not suitable for trucks with tail lift, or exact testing still required in case of order) Under-coupler drawbar, free drawbar length approx. 2200 mm Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the engine trolley, connection in FR-right EBS, electronic brake system with EBS plug at the front, with connecting cable, connection in FR right-hand side Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in each case in lowering / lifting position Vehicle - driving stability system Wheels and tires 235/75 R17.5`` tires of the manufacturer's choice Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 1 x 15-pin plug at the front, with connecting cable, connection in FR right-hand side 2 additional LED work lights at the rear, switched via reversing light 1 LED work light at the front, centered between the carriers, radiating to the rear, switched via reversing light Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Paint finish Ihedpfoi Riy Nox Ah Net Frame DB 7350 nova gray10-year warranty against rusting through Attention: Archive pictures!

Condition: new, machine/vehicle number: d9c951d746f03c05bc5470f89, empty load weight: 5 kg, maximum load weight: 29,045 kg, overall weight: 35 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis saddle forwarding Fine-grained steel welded construction, saddle plate with replaceable 2 kingpins Vario stanchion system 4 pairs embedded in loading area, can be pushed together to 2 100 mm and extended to approx. 3 500 mm for loading. Stanchions can be locked every 100 mm on an internal width of 2 100 mm to 3 000 mm, 4 pairs of divisible stanchions 600 mm + 1 200 mm, total height 1 800 mm removable. With an internal stanchion width from approx. 2 350 mm, excess width. Vario end walls Ijdpfxoi Ri R Do Ah Njht Floor prepared for inserting 3 end walls. 4 x 5 pairs of Vario stanchion pockets for insertable end walls (front and rear) and 1 x 3 pairs in the middle for transporting 2 x 5,000 mm or 2 x 6,000 mm construction steel mats. 2 Vario end walls, each consisting of 1 pair of plug-in stanchions and 1 top crossbeam approx. 2200 mm wide. Cross beams can be extended by 220 mm on both sides, with lashing hole for tensioning. 1900 mm high Vario bulkhead, can be converted to 1300 mm or 700 mm high. 4 stanchion pockets embedded in the center of the floor for 80 x 80 mm stanchions 1 pair of supports at the bottom for Vario bulkhead at the front 1 pair of lower supports for rear Vario bulkhead Slightly slanted outer frame with Load-Lock profile for lashing strap attachment 14 pairs of lashing eyes additionally embedded in the outer frame, 5 tons each 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Extension ladder at the rear Wheel chocks with holder Aluminium side collision protection Galvanized steel underride guard Quarter-shell mudguards in front of and behind axle unit with anti-spray flaps on last axle only Impact protection at the rear 8 construction steel winches with wire rope and counter hooks, 4 x left and 4 x right with rope feed-through through the outer frame, 1 removable slip-on gearbox for construction steel winches - supplied loose (without bracket on the frame) 1 spare wheel holder for 1 e-wheel, with wheel fastening set 1 plastic toolbox, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) 1 closed stanchion stowage box, open at the top, below loading area, doors on both sides, w=450 mm/h=400/420 mm/d=2460 mm 4 lashing/stanchion rails embedded transversely in the floor across the entire width up to the outer frame (max. usable internal width between the outer stanchions approx. 2170 mm), approx. 100 mm high. With 20 mm round steel slats, top and bottom, distance from top to bottom approx. 60 mm (of the round steel). For lashing and inserting stanchions 80 x 80 mm. Note: Stanchion pockets / stanchions are not designed for securing long material, pipes etc. on their own without wrapping around them. Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Axle lift below the recomm. Driving height, therefore no warranty for tire damage Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 swap-proof coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be to

Condition: refurbished (used), Year of construction: 2015, operating hours: 250 h, In the client's order: 3D coordinate measuring machine Hexagon Optiv 432 used multi-sensor CMM with camera, push button • Measuring range single sensor: 400x300x200mm • Dimensions: 1232x910x1663mm Mufjyo • Weight: about 940kg • Max. Workpiece weight: glass plate approx. 30kg • Accuracy: MPEE = 2.9 + L / 100 [? M] • built in 2014 • Software: Vision3D with option on Opticheck3D Isdpfxody Hlhj Ah Neht • incl. Camera with CNC zoom • incl. 6-fold button changer • Including switching push-buttons HP-TM • incl. LED ring light • incl. Calibration standard • incl. 2-monitor operation • incl. New Windows 7 Ultimate evaluation station • incl. Opticheck3D 4.5 evaluation software (12 months free software update) SYMBOL IMAGE OF THE MANUFACTURER (All rights reserved by Hexagon Metrology)

Condition: good (used), Approx. 55 order picking trolleys, with drawbar and coupling for assembling towing trains, also usable individually – used – : Price per unit: €225 (net)! Price for complete purchase: €199 (net) / unit! Priority is given to selling the entire lot! Manufacturer: unknown, presumably Wanzl Type: unknown, presumably KT4 Year of manufacture: unknown Load capacity: 500 kg Height incl. wheels: approx. 1.85 m Width: approx. 80 cm Depth / Length: approx. 1.30 m Equipped with drawbar and trailer coupling – allows creation of trolley trains The drawbar is spring-loaded, allowing it to be lifted and connected to the coupling of the leading trolley (video available on request) Isdpfx Aex Tdccjh Noht At least 1 intermediate shelf, some with 2 intermediate shelves Some units fitted with fork sleeves Load capacity: 500 kg One 'train' can consist of a maximum of 4 trolleys with max. 350 kg/trolley Max. speed: 4 km/h 2 push handles Condition: good Available: immediately Location: Dortmund area

Condition: new, Year of construction: 2024, ALZMETALL column drilling machine AB 34 iTRONIC drilling capacity in steel 34mm, spindle speed: 100-1800 rpm, Short spindle MK4, spindle stroke: 160mm, throat depth: 300mm, column diameter: 145mm, machine table usable support: 615x430mm, with T-slots 2 x 14mm x 224mm, distance spindle-table min. / max. 138/688mm, machine table height adjustment via hand crank, feeds 0.1-0.2-0.3-0.4 mm/rev, machine height without options: 1865mm, net weight: 470 kg. Standard equipment: 7" TFT LCD display with touch function Thread cutting device Infinitely variable speed adjustment Spindle protection Three separate buttons for clockwise rotation - counterclockwise rotation - stop Mushroom push button Main switch Clockwise and counterclockwise rotation Control voltage 24 Volt Protection class IP 54 Motor insulation class "F" (155°) Electromagnetic feed overload protection Machine oil initial filling Paint finish: DD textured paint signal white RAL 9003, PANTONE 7545c, black incl. the following options: LED machine light Pos. 12. Coolant system A Pos. 24 Foot switch for thread cutting Pos. 20.5 Delivery time: ex stock Waiblingen Beinstein Ihedpfx Ahjiqyixj Njt The machine can be viewed at our premises by prior arrangement.

Condition: used, mileage: 147,041 km, power: 62 kW (84.30 HP), first registration: 11/2012, fuel type: diesel, empty load weight: 1,421 kg, maximum load weight: 741 kg, overall weight: 2,162 kg, axle configuration: 4x2, wheelbase: 2,681 mm, fuel: diesel, CO₂ emissions: 161 g/km, fuel consumption (urban): 7.7 l/100km, fuel consumption (extra-urban): 5.1 l/100km, fuel consumption (combined): 6.1 l/100km, color: yellow, driver cabin: other, gearing type: mechanical, emission class: euro5, suspension: other, number of seats: 2, total length: 4,406 mm, Year of construction: 2012, construction height: 1,820 mm, Equipment: ABS, airbag, central locking, electronic stability program (ESP), immobilizer system, onboard computer, traction control, The Volkswagen Caddy 2.0 TDI is a versatile van that is ideal for commercial use. The vehicle is powered by a 2.0-liter diesel engine with 62 kW (84 hp) and meets the Euro 5 emissions standard. With an average consumption of 6.1 l/100 km, the Caddy offers a practical and economical transport solution. The Caddy is equipped with a 6-speed manual transmission and front-wheel drive. The vehicle has two sliding doors, which makes it easy to access the interior from both sides and offers a maximum side loading space of 2.65 m. The broom yellow paintwork gives it a fresh appearance. The dimensions are: height 1,823 mm, width 1,794 mm, and length 4,406 mm. The interior is functionally designed and offers space for two seats. The vehicle was first registered in November 2012 and has a mileage of 147,041 km. The main inspection is valid until December 2024. Delivery within Germany is possible for an additional charge. Sale only to commercial enterprises (agriculture, freelancers, small and large businesses) or export. Errors and prior sale reserved. Ihsdpetfawyefx Ah Njt

Condition: used, mileage: 162,252 km, power: 62 kW (84.30 HP), first registration: 07/2012, fuel type: diesel, empty load weight: 1,421 kg, maximum load weight: 741 kg, overall weight: 2,162 kg, axle configuration: 4x2, wheelbase: 2,681 mm, fuel: diesel, CO₂ emissions: 161 g/km, fuel consumption (urban): 7.7 l/100km, fuel consumption (extra-urban): 5.1 l/100km, fuel consumption (combined): 6.1 l/100km, color: yellow, driver cabin: other, gearing type: mechanical, emission class: euro5, suspension: other, number of seats: 2, total length: 4,406 mm, Year of construction: 2012, construction height: 1,820 mm, Equipment: ABS, airbag, central locking, electronic stability program (ESP), immobilizer system, onboard computer, traction control, This used Volkswagen Caddy 2.0 TDI, built in 2012, has a mileage of 162,252 km and complies with the Euro 5 standard. Powered by a diesel engine with 62 kW (84 hp) and a displacement of 1,968 cc, this vehicle offers a 6-speed manual transmission and front-wheel drive. Combined consumption is 6.1 l/100 km, while CO2 emissions are 161 g/km. Designed as a panel van, the Caddy has two sliding doors that allow side loading with a length of 2.65 m. The external dimensions are 4,406 mm in length, 1,794 mm in width and 1,823 mm in height. The wheelbase is 2,681 mm and the permissible total weight is 2,162 kg. The vehicle is in the color broom yellow R1032 and has a green environmental sticker. The equipment includes, among other things, a truck registration and a wooden plate in the loading area. Additional services such as a registration service and delivery within Germany can be arranged for an additional charge. This viewing is possible without registration. Iodpfx Aetfaxajh Noht Only sold to commercial customers (agriculture, freelancers, small and large businesses) or export. Errors and prior sale reserved.

Condition: used, machine/vehicle number: TX9S00000RP00xxxx, Year of construction: 2025, Please contact ATS Norway for more information Please provide reference number upon request: 21711 Specifications: 2025 model Length: 1350 cm Width: 255 cm Axle distance to second axle: 131 cm Axle distance to third axle: 201 cm Steering on axle 3 Curb weight: 6680 kg Payload: 38320 kg Full air suspension Front-mounted tipping cylinder Container locks Description:Special container semi-trailer with front-mounted tipping cylinder. Adapted for 20-, 30-, and 40-foot containers.You can easily adjust the trailer depending on whether you transport 20- or 30-foot containers. They can be moved hydraulically on the frame. When tipping the container, the entire container is pushed backward. Ijdpfxsxu A Ahe Ah Nsht Technical approved: no EU-approved until: 15.01.2026 Own weight: 6680 Total Weight: 45000 Payload: 38320 Width: 255 Length: 1350 Model: 2025 INVIPE Containersemi med tipp

Condition: used, machine/vehicle number: 381xxxx, Year of construction: 1997, Please contact ATS Norway for more information Please provide reference number upon request: 18602 Specifications: - 1997 model - 3 + 1 - Hydraulic Forced steering on 3 and 4 axles w/remote control Isdpfx Ajwphkpeh Noht - Auxiliary axle included - New hydraulic unit for steering - Manual Width - Piece of 2 meters - 1.70 cm Hydraulic extension - A good number of hydraulic hoses have been replaced - The one hydraulic central unit sweats a little hydraulic oil - Delivery by agreement   Description: 1997 Vang trailer Auxiliary axle included. Push piece of 2 m comes with and Hydraulic extension of 1,700 m. In total, you will find an extension of 3,700 m. The trailer is manually extended. There is also forced steering on 3 and 4 axles. Delivery by agreement Technical approved: Yes EU-approved until: 07.03.2026 Own weight: 11550 Total Weight: 81000 Payload: 69450 Width: 250 Length: 1613 Model: ATHLS 3+1 Brønnhenger

Condition: used, Year of construction: 2024, Optimum Optisaw SD500AV – Vario Bandsaw with Siemens Inverter Used bandsaw with signs of wear Heavy-duty industrial design Smooth, low-noise operation Manual or semi-automatic operation Infinitely variable saw band speed from 20–80 m/min High cutting precision due to vibration-free running Mitre adjustment from -45° to 60° by swivelling the entire saw bow Supplied as standard with high-quality bi-metal saw blade Microswitch for automatic shut-off Coolant pump Ball bearing saw band guide with carbide inserts for optimal cutting results Easy setting of descent speed via feed rate control valve on the control panel Large, hydraulically operated quick-action vise, self-closing, laterally adjustable Manometer for correct saw band tension Clearly arranged control panel Semi-automatic operation functionality: Closing of the vise and activation of the motor Lowering of the saw bow for cutting Stopping of the motor and return of the saw bow to its home position Dimensions and weights Length approx.: 2129 mm Width/depth approx.: 1046 mm Height approx.: 1687 mm Weight approx.: 645 kg Electrical data Output (motor power): 3 kW Hydraulic pump motor power: 1.4 kW Coolant pump motor power: 0.1 kW Total connected load: 3.8 kW Supply voltage: 400 V Mains frequency: 50 Hz Machine data Saw band speed(s): 20–80 m/min Saw band length: 3770 mm Saw band width: 34 mm Saw band thickness: 1.1 mm Cutting angle range: -45 to 60° Manual operation: hydraulic via push button Semi-automatic operation: automatic Continuous real-time data acquisition: Yes Data storage location: On device Data access: Via wireless interface Cutting capacities 0° round (solid): 355 mm 0° square (solid): 300 mm 0° rectangle upright (solid): 300 x 490 mm -45° round (solid): 290 mm Iodjx Dzv Eopfx Ah Njht -45° square (solid): 250 mm -45° rectangle upright (solid): 250 x 250 mm +45° round (solid): 350 mm +45° square (solid): 290 mm +45° rectangle upright (solid): 290 x 340 mm +60° round (solid): 230 mm +60° square (solid): 180 mm +60° rectangle upright (solid): 180 x 220 mm Explanation cutting capacity: Cutting capacity determined with aluminum based on saw bow weight. May vary when processing different materials and may be smaller in certain cases (this is not cutting capacity in the strict sense).

Condition: as good as new (ex-display), Year of construction: 2025, The machine is on display and has only been used for demonstration purposes. Optimill F50 E CNC milling machine, direct from the manufacturer. F50 E – The OPTIMUM CNC milling machine with Siemens SINUMERIK 808D Advanced control system stands out for its performance, speed, precision, and long service life. • Column design made of cast iron for high rigidity • Carousel-type tool changer with eight tool stations • All linear guides with stainless steel covers • Automatic central lubrication • Siemens main spindle motor • Siemens servo drive on all axes (closed-loop system) • Maximum spindle speed of 10,000 rpm • The portable electronic handwheel with enabling button and emergency stop slam switch greatly facilitates program setup • Coolant system with 70-liter coolant tank • Tool change carried out automatically or at the push of a button (electropneumatic tool clamping system) • Heavy-duty, precision-milled table – generously sized and finely surface-machined • Large access doors to minimize cleaning and maintenance times • LED machine lamp for full illumination of the work area • Additional SIEMENS package: material defect warranty and free on-site service (OSS) SINUMERIK 808D • Software package identical to control version, ensuring process reliability • LED tool number display • MCP with rotary switch for feed and spindle override • Absolute encoders – no reference run required • Higher accuracy Control • 8.4” LCD color display with 800 x 600 resolution Additional SIEMENS OSS package • 12 months; Item No. 3589010 • 36 months; Item No. 3589012 Dimensions and weights Length approx. 2030 mm Width/depth approx. 1600 mm Height approx. 1980 mm Weight approx. 1900 kg Electrical data Connection voltage 400 V Mains frequency 50 Hz Electrical connection Total connected load 10 kVA Horizontal milling table Length 690 mm Width 225 mm Vertical spindle to table distance min. 90 mm Vertical spindle to table distance max. 410 mm T-slot size 14 mm Number of T-slots 3 T-slot pitch 63 mm Maximum load 150 kg Accuracy Repeatability ± 0.015 mm Positioning accuracy ± 0.015 mm Pneumatic connection Operating pressure 6 bar Travel X-axis automatic 330 mm Y-axis automatic 220 mm Ihjdpfew Ea Swox Ah Not Z-axis automatic 320 mm Spindle to column distance min. 280 mm Spindle to column distance max. 280 mm Vertical spindle Spindle taper BT 30 Speed range 10,000 rpm Drive motor power S1 continuous operation 3.7 kW Drive motor power S6-30% duty cycle 5.5 kW Drive motor torque S1 continuous operation 24 Nm Drive motor torque S6-30% duty cycle 36 Nm Feed speed X-axis 15,000 mm/min Y-axis 15,000 mm/min Z-axis 15,000 mm/min Feed motor torque X-axis S1 continuous operation 3.5 Nm Y-axis S1 continuous operation 6 Nm Z-axis S1 continuous operation 6 Nm Tool changer Type: carousel Number of tool stations: 8 Max. tool diameter: 100 mm Max. tool length: 200 mm Max. tool weight: 6 kg Tool-to-tool change time: 7 s

Condition: new, power: 110 kW (149.56 HP), fuel type: diesel, axle configuration: 1 axle, fuel: diesel, brakes: other, color: white, driver cabin: other, gearing type: other, suspension: other, Equipment: ABS, air conditioning, airbag, central locking, cruise control, electronic stability program (ESP), fog lights, immobilizer system, onboard computer, traction control, CARGO AREA PROTECTION PACKAGE 2 (includes: Wooden floor (12 mm)), CLEAR VIEW PACKAGE (includes: Light and rain sensor), SAFETY/ASSISTANCE SYSTEMS (includes: ABS with electronic brakeforce distribution (EBD)), COMFORT (includes: Hands-free Keycard: Automatic unlocking of doors and/or tailgate upon approach, push-button start), CONNECTIVITY (includes: Easy Link 8-inch with smartphone integration), OUR FINANCING EXAMPLE: Finance this vehicle for 329.00 EUR per month., Price: 39,567, Down payment: 5,494, Net loan amount: 34,072, Effective annual interest rate: 4%, Nominal interest rate p.a.: 0%, Processing fee: 0, Term: 48 months, Gross loan amount: 35,246, 47x monthly installments: 329, Final installment: 19,783, Bank: RCI Banque S.A. German branch, Accessory highlights, ALL-SEASON TIRES, CARGO AREA PROTECTION PACKAGE 2 (includes: Wooden floor (12 mm), LED interior lighting (transverse bar), full side paneling), LEATHER-LOOK STEERING WHEEL, 12V SOCKET IN CARGO AREA, CLEAR VIEW PACKAGE (includes: Light and rain sensor, fog lamps), REAR DOORS 250° WITHOUT WINDOWS, SAFETY/ASSISTANCE SYSTEMS (includes: ABS with electronic brakeforce distribution (EBD), active emergency braking assist, brake assist with automatic hazard warning activation in emergency braking, eCall emergency system, electronic stability program (ESP) with load recognition, traction control and hill start assist, driver drowsiness alert, lane departure warning), COMFORT (includes: Hands-free Keycard: Automatic unlocking of doors and/or tailgate upon approach, push-button start, electric front windows with impulse function, cruise control with speed limiter, traffic sign recognition, rearview camera), CONNECTIVITY (includes: Easy Link 8-inch with smartphone integration, online multimedia system with 8-inch touchscreen, smartphone integration)... Changes, prior sale and errors excepted. Ihsdpfoyaf R Hox Ah Njt

Condition: used, mileage: 100,000 km, first registration: 06/2011, overall weight: 26,000 kg, Year of construction: 2011, Equipment: crane, Hiab superstructure XR 21 Z Push - articulated year 2011 with tank and in-cab controls Ihodpfeyafq Tex Ah Nst !!!!! SUPERSTRUCTURE ONLY - NO TRUCK !!!!! Transport - delivery possible - DE/Hamburg/Antwerp ..... Tel:

Condition: used, maximum load weight: 27,920 kg, overall weight: 36,000 kg, axle configuration: 3 axles, first registration: 01/2024, next inspection (TÜV): 02/2026, Saddle height 1,150 mm, Hydraulic: 110 l/mn, 225 bar, connections on front wall: 1''male screw pressure, 1''female screw return, BPW On Road Eco Air axles, lift 1..axle, EBS 2S/2M KNORR, JOST saddle supports steel, closed side collision protection painted RAL 9005 black, 2 LED work lights behind 3.axle and in front of support legs, 1x LED worklight in the interior n steel rims with black wheel hubs, 6kg fire extinguisher, 3-meter ladder, radio remote control for floor, shovel and broom holder, 2 toolboxes in overhang, 15-meter air hose with hydraulic drum and gun, 4400mm self-supporting chassis, aluminum body 3/2mm, catwalk front side with 2 ladders, door in front wall left with ladder, floor type 10mm, aluminum mobile wall with tarpaulin 3800gr. and rail cleaner, rear doors each with two integrated locking bars 18mm, reinforced sealing doors, rear upper cross member can be unlocked by pin on the right-hand side, pneumatic door release, black 650gr. roof roller tarpaulin with side reinforcement 200gr on 600mm, 12 pairs of lashing eyes, rear side wall wear plates 3x1.5m, black lashing straps integrated in side wall with stainless steel ratchets, side protection tarpaulin RAL7038 left Iodpfsq Dh Ngjx Ah Njht

Condition: used, Year of construction: 2009, functionality: fully functional, COMPLETE PET BOTTLING LINE KHS Product: Still Water Speed: 32,000 BPH Year: 2009 Cap: Corvaglia 29/26 Preform Hopper Preform Elevator Preform Orientator PET Blower KHS Model: Blowmax 16S Series IV Compressor Chiller Filling Monoblock: Filler Ihjdpox Tpygofx Ah Net 50 mechanical valves Type of filling: gravity Capper including elevator and orientator Type of cap: pre-threaded plastic Cap size: Corvaglia 29/26 Distribution system: pick & place Labeller PE 1 roll-fed station Mechanical cam plates Bottle inspector Shrink Wrapper Version: film launch Bundle 6x4 Palletizer Alvey 881 Type: push system Pallet Storage Pallet Wrapper Lantech Model: S1500 Type of wrapping: Rotating arm Pre-stretch Code: NP 695

Condition: like new (used), Year of construction: 1991, functionality: fully functional, overall weight: 35,000 kg, pressing force: 250 t, type of input current: three-phase, power: 30 kW (40.79 HP), punching force: 250 t, input voltage: 200 V, Equipment: safety light barrier, AIDA NC2-250(1) 250t eccentric press in excellent condition /ctA2/ Isdpfx Asu Dxb Toh Njht Manufacturer: AIDA Type: NC2-250(1) Push force: 160t Year of manufacture: approx. 1991 Stroke length: 170mm Distance above table: (adjustable) 280-400mm Table size: 2700x760mm Bear size: 2100x700mm Electrical power: 3x200V(!!), 30kW - Japanese standard Net weight: 35000kg Size: 2760x2800x3980mm Automatic greasing system. Automatic cutting oil dosing - RAZIOL EST-02 Optionally with disc winder and straightener.

Condition: new, Year of construction: 2026, machine/vehicle number: 2026, STEEL CUTTING MACHINE with ONLINE-PC-STEUERUNG350 fully automatic steel cutting machine for reinforcing steel cutting in a single - or double cut according to requirement. Optimized cutting with residual lengths. The system consists of an automatic Vorlegemagazin with 12 seats, a hacksaw and a belt conveyor to the removal of cut-to-length steel profiles. Rest lengths to promote after length in a rest length basket, transport or waste basket. The steel profiles are processed in the process, while the profile bar is precisely positioned by a transport gripper with linear motor and rotary encoders. The saw cut is made from the top, Microdosier-cooling-lubrication system ensures optimum cooling of the blade. Ihjdpfxecmqkmj Ah Not The profile is, profile cross section regardless, pneumatically. Free-standing system with PC control or in combination with an automatic cutting machine, plastic-BAZ or SBZ. In a combination of stroke with the automatic cutting machine, BAZ or SBZ is synchronized. Profile lists for the store in the template magazine displays the employee on the TFT screen. The finished steel profiles are taken from the belt conveyor, acknowledged and filed in car, or manually pushed to the Stahlein-schubstation in the PVC profiles. New facility 10 weeks delivery time

Condition: new, Year of construction: 2022, functionality: fully functional, machine/vehicle number: S20185, The DMK 20 C2 table cutter is NEW, UNUSED STOCK. Due to its compact, robust, and precise construction, it is the ideal table cutter for small to medium-sized meat processing companies, high-end gastronomy, as well as large kitchens and catering services. The well-thought-out design gives the user virtually unlimited application possibilities in all areas. The machine is equipped with two independently operated, powerful motors, allowing for versatile control. The optionally available robust, mobile base frame ensures the mobility you need. The net weight of 260 kg speaks for itself—an absolute professional-grade machine! A bargain for the expert! You will receive an invoice with VAT shown separately. Our used equipment service for you: • 6-month warranty on all electrical parts • High-quality branded appliances at fair prices • Professional overhaul/inspection & expert cleaning • Tested & fully functional—or your money back • Shipping or self-collection—flexible options • Competent advice—before and after purchase • Provision of operating manuals, wiring diagrams & spare parts • Inspection according to DGUV V3 Professional engineering in the tightest space: The DMK 20 C2 table cutter impresses with its extremely smooth and low-vibration operation, even at high speeds. The complex manufacturing of the individual components is carefully and precisely matched. The thick-walled, high-grade stainless steel cutting bowl offers extremely accurate concentricity, allowing the cutter knives to be set very close to the bowl radius. Applications: Machine specifications: • All stainless steel construction • Solid cast stainless steel bowl (bowl capacity: 20L) • High-precision, maintenance-free cutting unit • Stainless steel knife head with 6 knives • Tight cutting clearance in the bowl radius • High stability • Extremely low-vibration operation • Vibration-damping machine feet • Cutter lid made of Plexiglas • Analog, easily readable thermometer • 6 stainless steel knives, 7 stainless steel filler rings, two bowls Drive & control: • Separate knife shaft drive with electromagnetic brake Ihedpfx Ahow N Ipko Njt • Brake release function via push button for cleaning with lid open • Separate bowl drive with directly flanged, maintenance-free gearbox • Two speeds, independently switchable • User-friendly, large push buttons with hygienic protective covers Safety features: • Spill guard according to UVV • Interlock guard according to UVV • Noise protection lid • Electromagnetic brake • EMERGENCY STOP function • Machine meets HACCP • Machine meets UVV • BG certified Technical data: • Bowl volume: 20L • Useful capacity for fine sausage meat (approx. kg): 16kg • Number of knives: 6 • Speed (rpm): 1500/3000 • Knife shaft power (kW): 3.3/4.5 • Mains voltage (V): 400 • Control voltage (V): 24 • Fuse protection (A): 16 (slow-blow) • Dimensions (W x D x H): 83cm x 80cm x 63cm • Weight: 260 kg Options: • Mobile base frame • Serial number: S20185 • Year of manufacture: 2022 • Type: DMK 20 C2 Condition: New

Condition: reconditioned (used), FEINTOOL HFA 400 is a Fine blanking machine designed for precision, high accuracy and reliability. Capacities: total capacity 4000 kN; vee-ring indenter pressure 1800 kN; back pressure 800 kN; pushing ram 300 kN; stripping 590 kN; tool faces sup. 800x800 mm, inf. 1000x810 mm; cutting speeds 5–50 mm/s, close traverse max 120 mm/s, return 135 mm/s, up to 150/230 c/min. Specs: 3x380 V 50 Hz, main motor 75 kW, total power 82 kW, weight ≈21700 kg, dimensions 5000x3300x3360 mm. Accessories: roll-feed, belt feeding, decoiler. Achieves tight tolerances for demanding industrial applications. Ijdpfx Ahex S N Hwe Nsht

Condition: good (used), Year of construction: 2015, Type: Torri Quantity: Frame 7800 x 1100 mm 340 pcs Cross beams/traverses 3600 x 120/50 mm approx. 1200 pcs. Load capacity: 600 kg/m2 Surface: chipboard 38 mm High top edge of floor covering: 8100 mm A total of approx. 3,000 m² is still available. Drawings can be found under the pictures. Ijdpfx Aoihvp Deh Njht We sell the storage platform and the pallet racking system separately, you can also buy the storage platform without the chipboard decking. If you require shelving or accessories in other configurations or designs, please contact us. We offer a comprehensive range of new and used shelving and accessories and will be happy to assist you with your planning. Further accessories such as Frame, corner and collision protection, push-through protection, chipboard, gratings, rear wall gratings, depth bars available. Shipping: Please enquire about freight costs, stating your zip code and location, as well as the required quantity of items. Further services: Planning, shelf assembly/disassembly, purchase/sale Subject to changes and errors in technical data, information and prices as well as prior sale!

Condition: good (used), For pallet racks with 800 mm frame depth Size: 530x800 mm Load capacity: 140 kg / panel If you need shelves or accessories in other compositions or designs, please contact us. We offer a comprehensive range of new and used shelving units and accessories and accessories and are happy to assist you with your planning. Isdpfx Ahogz H R Ie Neht Further accessories like for example: Frame, corner and collision protection, push-through protection, chipboard, grids, rear wall grids, depth bars available. Shipping: Please enquire about freight costs, stating your postcode and location, as well as the desired item quantity. Further service offers: Planning, shelf assembly/disassembly, purchase/sale. Changes and errors in the technical data, information and prices and subject to prior sale!

Condition: used, Frame: 6000x1000 mm Beams: 4300x120 mm If you require shelving or accessories in different configurations or versions, please contact us. We offer a comprehensive range of new and used racking as well as accessories, and are happy to assist you with your planning. Further accessories such as frame protectors, corner and collision guards, push-through protections, chipboard shelves, wire mesh shelves, mesh rear panels, and depth bars are available. Shipping: Please inquire about shipping costs by providing your postcode, location, and the desired quantity of items. Ihedpjpu Amhjfx Ah Not Additional services: Planning, racking assembly/disassembly, purchasing/sales Technical data, specifications, and prices are subject to change and errors excepted. Prior sale reserved!

Condition: good (used), Crossbars: 1250*40*40 mm If you need shelves or accessories in other compositions or designs, please contact us. We offer a comprehensive range of new and used shelving and accessories and will be happy to assist you in your planning. Further accessories such as: Frame, corner and collision protection, push-through protection, chipboard, grating, rear wall grating, depth bars available. Ihodpfx Ahsh Izuhe Not Shipping: Please ask for the freight costs by stating your postal code and location, as well as the desired article quantity. Further service offers: Planning, shelf assembly/disassembly, purchase/sale. Changes and errors in the technical data, information and prices and subject to prior sale!