Used Powder for sale (1,072)

Condition: used, Year of construction: 2010, functionality: fully functional, Wagner Powder painting equipment for sale! Powder coating device, year 2010 consisting of: Booth: Prima Cube 16000 Powder supply: Powder Center Powder recovery: Cyclon Filter 16000 Movement generator: KHG 350 Production process configurations INCLUDING: I. Presumes Maximum size of parts: LxWxH=2600x400x1850 mm II. Equipment Technological Conveyor automatic speed V=1.2 mtrs/min. Speed regulation between 0.5-2.5 mtrs/min 1. Pretreatment Stand MNA-3-LPG, total size 16,7 mtrs Enter size L=2,5 mtrs a. Washing, degreasing and phosphating; L=3,6 mtrs -number of spray frames – 10 -number of nozzles in frame – 18 -number of nozzles in total – 180 -delivery of the pump – 162 m3/h -power of the pump – 15 kW -vessel 4 m3 for active liquid -inner heat exchanger with LPG burner – 160 kW -temperature 500C -mechanical oil separator - solution filter -the dosing system, membrane pump with regulator -washing time – 3 min b. Dripping zone L= 3,1 mtrs -time of dripping – 2 min 30 sec c. First rinsing; L= 1,2 mtrs -number of spray frames – 4 -number of nozzles in frame – 18 -number of nozzles in total – 64 -delivery of pump – 38 m3/h -power of the pump – 3 kW -vessel 1,5 m3 for water -first rinsing time – 1 min c. Dripping zone L= 3,1 mtrs -time of dripping – 2 min 30 sec d. Fine rinsing; L= 1,28 mtrs -number of spray frames – 3 -number of nozzles in frame – 18 -number of nozzles in total – 54 -delivery of pump – 33 m3/h -vessel 1,5 m3 for water -power of the pump – 3 kW Laedpfx Afsww Adtsfjk -one extra spray frame -number of nozzles in frame – 18 -fine rinsing time – 1 min e. Dripping zone L= 2 mtrs -time of dripping – 1 min 40 sec Three openings to connect to exhaust system with three ventilators Operating space made of stainless steel. Pipes made of PVC or S/S. 1 unit 2. Automatic Dryer after water AST-1-KLPG: - operating space dimensions LxWxH=7000x3000x2800 - air curtains each side to avoid heat losses - one indirect heat exchanger heated with liquid petrol gas to produce 200 kW of rated power - three blowers 6000 m3/h of air delivery - two openings to connect to exhaust system - temperature sensor and temperature regulator - overheating sensor - circulation sensor - operating space made of zinc plated steel - thermal insulation 200 mm thick - drying time 10 min 1 unit 3. Automatic Curing Oven APT-2-KLPG for curing powder paints - operating space dimensions LxWxH=10200x3600x2800 - air curtains on one side to avoid heat losses - two indirect heat exchangers heated with liquid petrol gas to produce 300 kW of rated power, of each - eight circulation blowers, capacity of each 6 000 m3/h - two openings to connect to exhaust system - temperature sensor and temperature regulator - overheating sensor - circulation sensor - operating space made of zinc plated steel - thermal insulation 200 mm thick - curing time 25 min 1 unit 4. An overhead rail conveying system ATR-ADAX, for the paint shop including the following: • straight track with hangers L=400 mm 146 mtrs • drive station 2 pc • tension station 1 pc • chain lubrication station 1 pc • drawing of the track supporting structure 1 set

Condition: used, Manufacturer: Mineralwerke Type: PZ 250 M4 Voltage: 380 V Output: 55 kW Weight: 1950 kg Ledpfx Afsh D Hmvefeak

Condition: new, Year of construction: 2025, VG1E-VN MANUAL FAST COLOR CHANGE TYPE POWDER COATING SYSTEM The powder coating system is designed for powder coating applications with frequent color changes during the day. The equipment is on a wheeled stand for ease of operation. Powder coating is sucked directly from the powder box, which allows rapid color changes. The powder box is placed on the vibrating table, suction pipe fluidizes the powder coating in the box, ensuring effective mixing, and the powder coating is homogeneously sent to the gun through an injector placed on the suction pipe. TECHNICAL SPECIFICATIONS Input voltage : 220V 50Hz Air need : 350 lt/min Input pressure : 6 bar Vibration motor : 220V 25W Gross weight : 55 Kg VG4 CONTROLLER AND MANUAL POWDER COATING GUN The VM manual powder coating gun is completely dismountable. The ergonomic gun handle design ensures ergonomic handling and does not tire the operator during coating application. The high voltage cascade has a long service life, its tightness prevents contact with dust and minimizes the risks in this area. The well-designed head assembly and nozzle ensure excellent polarization and homogeneous coating on surfaces during application. The electronic touch panel on the back of the gun provides ease of use during operation. The control unit is digital and allows precise adjustment of settings via the touch panel. TECHNICAL SPECIFICATIONS Gun Type : Corona System Polarization : Negative Cascade input voltage: 0-10,5V DC Output voltage : 100 kV Output current : 0 -150 μA Powder output (3,5 bar) 500 g/min Protection class : IP 54 Voltage cable length : 5 m Powder hose length : 5 m Gun weight (gross) : 450 g Operating temperature :-20-50 ° C Nozzle :Flat jet or Ø16-20-24mm deflectör Lasdpfjvv N Tyjx Affek

Condition: used, Folding former, folding machine, form folding machine, profiling machine, profiling system, slat production, blind production, dryer, infrared dryer, powder coating -Infrared dryer: used for powder coating slats/blinds production -Manufacturer: Himmel, type HA 5-2-9/500 -Geared motor: WEG 0.37 kW -Dimensions: 880/1050/H2200 mm Lodsgal A Iepfx Affsak -Weight: 308 kg

Condition: good (used), G Webb Automation MiniFill screw feed doser feeding onto weigh platform. Perfect for packing powders, granules, coffee etc into bags. Lasdpfjm Sg Hcex Affok

Year of construction: 2023, condition: new, functionality: fully functional, Xtrutech XTS 35 for powder coatings (180-350 kg/hr) 1. PURPOSE AND MAIN FUNCTIONS OF THE LINE The extrusion line for powder coating production is part of a whole production process and is used for the production of polymer powder coatings. The extrusion line includes the following technological processes: formation of a homogeneous melt of heated powder coating by mixing, shaping of the melt, subsequent cooling of the product and its crushing into fine fractions. 2. LINE COMPONENTS - Twin-screw extruder type XTS 3. DESCRIPTION OF THE EXTRUDER COMPONENTS 3.1. Twin-screw extruder type XTS 35 The extruder for powder coating production consists of: - 24D hydraulically opening barrels at the top and bottom, providing quick access for cleaning, maintenance and emergency repair of barrel liners and screw element shafts. - Rectangular loading port for dosing of materials which are difficult to dose. - Robust high flow water cooled units with 5 electrically heated (aluminium bronze heating plates of 2 kW each) control zones that provide excellent temperature control. Maximum operating temperature is 350°C. - The barrel on the discharge side is equipped with a cooled discharge adapter and a knife. - Screws with screw elements. Screw speed 0 - 900 rpm. Water cooled AC motor power of 26kW. The stepless (PIV) gearbox is rated at 139Nm and protected by an automatic torque limiter. - Latch lock / quick-release coupling of shaft connection and toothed shaft. Mains supply voltage: 400±6%, 3 phases, 50 Hz (o+earth). Control: 24V. Ljdpswz Ntiefx Affjak Water-supply: 70 l/min at 15°C and a coolant pressure of 4bar. Approximate dimensions: L=2250mm W=1000mm H=1600mm Approximate weight: 1600kg. High-volume geometry D/d =1.8 AC motor power 26 kW Screw speed 900 rpm Average output 180 - 220 kg/h, max. 350 kg/h

Condition: new, Year of construction: 2024, Basic info: • Intuitive 7" touchscreen display on the rotating applicator head, with convenient position lock • Up to 20 user programs • 3 automatic programs: flat, hard-to-reach surfaces, repainting • Handle and foot for easy transport in the paint shop • Gun rest handle prevents the gun from falling off the applicator • Powder cable holder prevents damage and optimizes powder flow to the gun • Accessories drawer - nozzles and spare parts • Attractive, modern design • Quick color change with collection directly from the box • Automatic cleaning function - gun blow-off Lsdpfx Afeflpi Nefoak • Remote control of paint amount and program changes from the handle level • A complete set of hoses included; 6m - antistatic hose • Stand with vibrator and suction unit with fluidization Additional info: • Powder consumption up to 200g/min • Air consumption up to 200L/min 6 Bar • Air quality / water vapor - less than 1.3g/nm 3 • Air quality / oil - less than 0.1mg/nm3 • ATEX compliance 2mJ

Condition: new, Year of construction: 2025, MANUAL POWDER COATING PLANTS AND SYSTEMS Our design department will give you the best customized powder coating line solution which meets your product capacity demands. Made in Türkiye CE Mark Ljdpfx Aevv Nuqeffjak We offer the best technical solutions and competitive prices * Office in France and Germany, Contact us for more information and quotations

Condition: used, Lacquer roller machine, roller application machine, powder coating plant Lasdpfx Afsgal Anofok -Powder coating system: used for slats/blinds production -Pneumatic components: Manufacturer Festo -Geared motor: WEG 0.25 kW -Dimensions: 3400/850/H1935 mm -Weight: 746 kg

Condition: used, Gainsborough bagger and All-Fill powder depositor. Lajdjvvpphjpfx Affok

Condition: new, Year of construction: 2025, functionality: fully functional, machine/vehicle number: KAP1, air demand: 16,000 m³/h, power: 36 kW (48.95 HP), suction capacity: 16,000 m³/h, Equipment: cabin, Dielectric automatic powder booth KAP1 Price: PLN 492,693.30 + VAT Electrical and energy data • Voltage: 400 V (3P + N + PE) • Power connection: 36.34 kW • Pneumatic connection: 1" • Air pressure: min. 6 bar • Air quality: oil < 0.1 mg/m³, water vapor < 1.3 g/m³ • Air consumption: 1710 Nl/min (operation) • Compressor: SC-30 • Air tank: 1800 L Painting parameters • Painting speed: 1933 mm/min • Part dimensions: 800 x 1800 mm • Hanger height: 500 mm • Coating thickness: 100 µM • Gun array: vertical Technical data and configuration • Design: dielectric plastic • Passage dimensions: 1000 x 2400 mm Laedpfxev Rpx Ss Affjk • Air flow: 12348–16000 m³/h • Powder center: ProfiCenter CP02 • Manipulators: 2 pcs. • Guns: 8 automatic, 2 manual (ProfiSpray) • Part detection: yes (height, width) • Systems: cyclone separator, ProfiControl, beam pulling • ATEX: zone 22, II 3D Platforms and cabin body • Platforms: entry, exit, stainless steel floor, anti-slip stairs • Housing: dielectric plastic, LED lighting, slots for manipulators Air knives and suction channel • Automatic floor cleaning • Suction channel with pneumatic flap Gun blow-off and control • Automatic blow-off guns • 10" touch panel, 50 programs, manipulator control, dust extractor, drive speed X-axis and part pulling system • Automatic gun setting • Part pulling: speed 570–2830 mm/min, 2 pullers The machine also includes: • ProfiSpray A applicator • PSS-1 controller • PM-1 guns • ProfiCenter CP-02 powder center • CK-D1400L cyclone dust extractor • MA1-180 manipulator and MX1-10 X-axis • OZ-12H dust extractor • ProfiControl 10" control • BP-H2000 W900 part measuring system

Condition: new, Year of construction: 2025, POWDER COATING SYSTEM FOR CAR WHEELS AND RIMS Lsdpfxjvv Rfdj Affsak Oven contains 4 pieces of 22’ wheel rims in 1 batch COMPONENTS OF THE PLANT: * 1.5x1x1.3m POLYMERIZATION OVEN, 18KW ELECTRICAL * VFK-2 ONE-SIDED POWDER COATING CABINET * OVERHEAD CONVEYOR AND LOAD TROLLEYS * MANUAL POWDER COATING EQUIPMENT Delivery: 6-8 weeks EXW Istanbul factory Assembly and training included We offer the best technical solutions and competitive prices * Office in France and Germany, Contact us for more information and quotations

Year of construction: 2020, condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) Lodpfx Afefx Nfmofoak For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. History 20 latest of burn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning.

Year of construction: 2020, condition: new, High hauling power Soundproofed construction Electronic control 4 "touch panel Constant measurement of flow and filter clogging Final filters Inverter controlled fan • Electrical data 22kW 380-400V 50-60Hz • Theoretical capacity 12000 m3 / h • 1/4 "pneumatic connection • Number of filters 8 pcs. • 160 m2 filtration area • Automatic filter cleaning • Air consumption max. 12L 6-8 bar / shot • 50L waste container capacity Description • Dust collector equipped with an efficient radial impeller • Two working modes - Full power and ECO • The basis weight of the material used in the filter is as much as 260g / m2 • High suction power with low energy consumption • Waste container for easy removal of paint deposits • Inspection door for filter replacement • Each filter has its own solenoid valve Power Inverter Constant air flow measurement Vacuum sensor Ljdpfxsfz Dqxe Affoak Capacity (m3h) Filter area (m2) Paint container

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. Lasdpfx Aofz Dubsffsk The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, ROMER cabins are equipped with 4 "color touch screen.The cab operation is intuitive, takes place in 3 modes, automatic (time), automatic (based on a clogged filter sensor), or manual.The cabins are fitted with a sensor that queues filters for cleaning when they plug. The system also informs when the filters have already worn out. The electronic system of automatic filter cleaning has a range of adjustment of cleaning frequency and time of firing. Each filter is cleaned separately, and the filters can also be cleaned manually using the buttons. We know from experience that it is difficult for the operator to enforce filter cleaning. Thanks to this system, the operator will not have to think about it anymore. Aluminum fans are very quiet, work at 74-79dB - It's not much. it is difficult to talk even with a standard cabin construction.The cabin, by pulling the sling beams inside the cab, improves the work efficiency, thus relieving the painter, who does not have to move them by hand anymore. ROMER cabins are equipped with 4 "color touch screen.The cab operation is intuitive, takes place in 3 modes, automatic (time), automatic (based on a clogged filter sensor), or manual. Filter clogging sensor The cabins are fitted with a sensor that queues filters for cleaning when they plug. The system also informs when the filters have already worn out Automatic filter cleaning The electronic system of automatic filter cleaning has a range of adjustment of cleaning frequency and time of firing. Each filter is cleaned separately, and the filters can also be cleaned manually using the buttons. We know from experience that it is difficult for the operator to enforce filter cleaning. Thanks to this system, the operator will not have to think about it anymore.Low volume Aluminum fans are very quiet, work at 74-79dB - It's not much. it is difficult to talk even with a standard cabin construction. Broach through the cabin The cabin, by pulling the sling beams inside the cab, improves the work efficiency, thus relieving the painter, who does not have to move them by hand anymore.Automatic filter cleansing Laodsfy T Tbopfx Affek ROMER's cabins are equipped with an electronic automatic filter cleaning system. Booth has an adjusted range of cleaning interval, time of the impulse. Each filter can be cleaned individually by using control buttons. We know from experience that it's hard to expect from an operator to clean every single filter entirely. Thanks to this system operator won't have to worry about it anymore. Booth drive-through chain Thanks to installed drive-through chain there is no need for an operator to drag every element into the booth himself.Elements drive through the booth all on their own which improves the efficiency and allows operator to focus just on the painting part.Regulated air suction In our booths we install an anti-static plate that covers filters. It protects filters from a first wave of a powder. In a well designed booth it also improves the velocity of air moving across the painted element that reaches filters. It improves suction and makes painting easier. Location of a plate can be regulated ROMER's powder booths are fitted with professionally made tanks, which are responsible for the collection of air needed to clean the filter. Compressed air is released from the tank in a fraction of a second while passing through the ROMER JET ™ system expands in the filter at high velocity and escapes through the micro holes in the filter cleaning it, and the

Year of construction: 2020, condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) Laedpjfz Apqefx Affek For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. History 20 latest of burn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning.

Year of construction: 2020, condition: new, Touch control ROMER cabins are equipped with 4 "color touch displays. Operation of the cabin is intuitive, takes place in 3 modes, automatic (time), automatic (based on a clogged filter sensor), or manual Filter clogging sensor Ledpfx Aofz A Ilsffjak A sensor is installed in the cabins, which queues the filters for cleaning when they become clogged. The system also informs you when the filters have worn out Automatic filter cleaning The electronic system for automatic filter cleaning has a range of cleaning frequency and shot time adjustment. Each of the filters is cleaned separately, the filters can also be cleaned manually using the buttons. We know from experience that it is difficult for the operator to enforce filter cleaning. Thanks to this system, the operator will not have to think about it anymore. Low volume Aluminum fans are very quiet, they work at the level of 74-79dB - It's not much. with the standard cabin structure, it's even hard to talk. Broaching machine through the cabin By dragging the suspension beams within the cabin, the cabin improves work efficiency, thus relieving the painter who no longer has to move them by hand. Explosion-proof design The booths are designed to prevent the formation of an explosive mixture during the painting process. Each of the components has been carefully selected to minimize this risk.

Year of construction: 2020, condition: new, High hauling power Soundproofed construction Electronic control 4 "touch panel Constant measurement of flow and filter clogging Final filters Inverter controlled fan • Electrical data 22kW 380-400V 50-60Hz • Theoretical capacity 12000 m3 / h • 1/4 "pneumatic connection • Number of filters 8 pcs. • 160 m2 filtration area • Automatic filter cleaning • Air consumption max. 12L 6-8 bar / shot • 50L waste container capacity Description • Dust collector equipped with an efficient radial impeller • Two working modes - Full power and ECO • The basis weight of the material used in the filter is as much as 260g / m2 • High suction power with low energy consumption • Waste container for easy removal of paint deposits • Inspection door for filter replacement • Each filter has its own solenoid valve Power Inverter Constant air flow measurement Vacuum sensor Lasdpjfz I Rmsfx Affok Capacity (m3h) Filter area (m2) Paint container

Year of construction: 2020, condition: new, High hauling power Soundproofed construction Electronic control 4 "touch panel Lajdpfx Afefz I R Rjfsk Constant measurement of flow and filter clogging Final filters Inverter controlled fan • Electrical data 22kW 380-400V 50-60Hz • Theoretical capacity 12000 m3 / h • 1/4 "pneumatic connection • Number of filters 8 pcs. • 160 m2 filtration area • Automatic filter cleaning • Air consumption max. 12L 6-8 bar / shot • 50L waste container capacity Description • Dust collector equipped with an efficient radial impeller • Two working modes - Full power and ECO • The basis weight of the material used in the filter is as much as 260g / m2 • High suction power with low energy consumption • Waste container for easy removal of paint deposits • Inspection door for filter replacement • Each filter has its own solenoid valve Power Inverter Constant air flow measurement Vacuum sensor Capacity (m3h) Filter area (m2) Paint container

Year of construction: 2020, condition: new, High hauling power Soundproofed construction Electronic control 4 "touch panel Constant measurement of flow and filter clogging Final filters Lodsfz I Sgepfx Affjak Inverter controlled fan • Electrical data 22kW 380-400V 50-60Hz • Theoretical capacity 12000 m3 / h • 1/4 "pneumatic connection • Number of filters 8 pcs. • 160 m2 filtration area • Automatic filter cleaning • Air consumption max. 12L 6-8 bar / shot • 50L waste container capacity Description • Dust collector equipped with an efficient radial impeller • Two working modes - Full power and ECO • The basis weight of the material used in the filter is as much as 260g / m2 • High suction power with low energy consumption • Waste container for easy removal of paint deposits • Inspection door for filter replacement • Each filter has its own solenoid valve Power Inverter Constant air flow measurement Vacuum sensor Capacity (m3h) Filter area (m2) Paint container

Year of construction: 2020, condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Lasdpefz U Nbofx Affjk Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. History 20 latest of burn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning.

Year of construction: 2020, condition: new, Automation Use of one photocell Using one photocell in the space of workpiece allows you to measure the length of the workpiece and, consequently, gives you the opportunity to turn on the guns when the item is in range, and to switch off the gun immediately after the workpiece is finished. The photocell is included in the standard equipme Array of guns Vertical 8pcs. pistols Control - profiControl 10 " Cyclone - CK-D1250 Dust collector - OZ-8H Center - RP-01 + SV-200 MA1-23 x 2 pcs manipulator Os X MX-100 x2 pcs. Horizontal goal - Horizontal goal W400 x2 items Vertical gate - H2000 vertical gate The maximum painting speed is 1,65714285714286m / min 0 piece pulling machines Pow. requires 10188m3 / h to fly Ledpsflq Spofx Affjak Required min. cabin passage W900mm H2100mm Pipe diameter 500mm - 16.9m / s minimum 16m / s Air consumption 1210 L / min + Sug. SC-20 compressor Min.current connection 28.14 kW Identification of details using special tags. A plate with identification holes is placed over the suspension. Based on this, the PLC controller in conjunction with the photocell recognizes the painted detail, turns on and off the guns in a timely manner - thus braking the energy and powder coating. Vertical detection of the detail of the workpiece. The use of light gates with detectors horizontally allows the PLC to analyze the vertical shape of the workpiece. The PLC counts the time at which the detail should appear in the gun space - allowing guns to be selectively switched on or off. Application of light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of the dimensions of the workpiece, which makes it possible also to manipulate the manipulators. Benefits of using gates and photocells The benefits of using photocells or light gates are primarily energy and powder savings. Eliminate painting of a zone in which there is no detail. With the use of light gates, precise control of the guns. Our lines can be optionally equipped with photocells, or light gates Using one photocell in the workpiece space allows you to measure the length of the workpiece and, consequently, gives you the ability to turn on guns when the item appears in their range, and turn off the gun immediately after the workpiece is finished. Identification of details using special tags. A plate with identification holes is placed over the suspension. Based on this, the PLC controller in conjunction with the photocell recognizes the painted detail, turns on and off the guns in a timely manner - thus saving the energy and powder. The use of light gates with detectors horizontally allows the PLC to analyze the vertical shape of the workpiece. The PLC counts the time in which the detail will appear in the gun space - allowing guns to be selectively switched on or off. Using of light gates with multiple sensors horizontally and vertically This solution allows precise measurement of the dimensions of the workpiece, which makes it possible also to adjusting the manipulators. The benefits of using photocells or light gates are primarily powder and energy savings Eliminate painting of a zone in which there is no detail With the use of light gates, precise control of the guns.

Year of construction: 2020, condition: new, Touch control Ledpfefzktzox Affsak ROMER cabins are equipped with 4 "color touch displays. Operation of the cabin is intuitive, takes place in 3 modes, automatic (time), automatic (based on a clogged filter sensor), or manual Filter clogging sensor A sensor is installed in the cabins, which queues the filters for cleaning when they become clogged. The system also informs you when the filters have worn out Automatic filter cleaning The electronic system for automatic filter cleaning has a range of cleaning frequency and shot time adjustment. Each of the filters is cleaned separately, the filters can also be cleaned manually using the buttons. We know from experience that it is difficult for the operator to enforce filter cleaning. Thanks to this system, the operator will not have to think about it anymore. Low volume Aluminum fans are very quiet, they work at the level of 74-79dB - It's not much. with the standard cabin structure, it's even hard to talk. Broaching machine through the cabin By dragging the suspension beams within the cabin, the cabin improves work efficiency, thus relieving the painter who no longer has to move them by hand. Explosion-proof design The booths are designed to prevent the formation of an explosive mixture during the painting process. Each of the components has been carefully selected to minimize this risk.

Year of construction: 2020, condition: new, ROMER cabins are equipped with 4 "color touch screen.The cab operation is intuitive, takes place in 3 modes, automatic (time), automatic (based on a clogged filter sensor), or manual.The cabins are fitted with a sensor that queues filters for cleaning when they plug. The system also informs when the filters have already worn out. The electronic system of automatic filter cleaning has a range of adjustment of cleaning frequency and time of firing. Each filter is cleaned separately, and the filters can also be cleaned manually using the buttons. We know from experience that it is difficult for the operator to enforce filter cleaning. Thanks to this system, the operator will not have to think about it anymore. Aluminum fans are very quiet, work at 74-79dB - It's not much. it is difficult to talk even with a standard cabin construction.The cabin, by pulling the sling beams inside the cab, improves the work efficiency, thus relieving the painter, who does not have to move them by hand anymore. ROMER cabins are equipped with 4 "color touch screen.The cab operation is intuitive, takes place in 3 modes, automatic (time), automatic (based on a clogged filter sensor), or manual. Filter clogging sensor The cabins are fitted with a sensor that queues filters for cleaning when they plug. The system also informs when the filters have already worn out Automatic filter cleaning The electronic system of automatic filter cleaning has a range of adjustment of cleaning frequency and time of firing. Each filter is cleaned separately, and the filters can also be cleaned manually using the buttons. We know from experience that it is difficult for the operator to enforce filter cleaning. Thanks to this system, the operator will not have to think about it anymore.Low volume Aluminum fans are very quiet, work at 74-79dB - It's not much. it is difficult to talk even with a standard cabin construction. Broach through the cabin The cabin, by pulling the sling beams inside the cab, improves the work efficiency, thus relieving the painter, who does not have to move them by hand anymore.Automatic filter cleansing ROMER's cabins are equipped with an electronic automatic filter cleaning system. Booth has an adjusted range of cleaning interval, time of the impulse. Each filter can be cleaned individually by using control buttons. We know from experience that it's hard to expect from an operator to clean every single filter entirely. Thanks to this system operator won't have to worry about it anymore. Laodpfx Afefz Atbefek Booth drive-through chain Thanks to installed drive-through chain there is no need for an operator to drag every element into the booth himself.Elements drive through the booth all on their own which improves the efficiency and allows operator to focus just on the painting part.Regulated air suction In our booths we install an anti-static plate that covers filters. It protects filters from a first wave of a powder. In a well designed booth it also improves the velocity of air moving across the painted element that reaches filters. It improves suction and makes painting easier. Location of a plate can be regulated ROMER's powder booths are fitted with professionally made tanks, which are responsible for the collection of air needed to clean the filter. Compressed air is released from the tank in a fraction of a second while passing through the ROMER JET ™ system expands in the filter at high velocity and escapes through the micro holes in the filter cleaning it, and the