Used Plunge Pool for sale (233)

Condition: used, Grinding wheel dimensions (OD x ID x width): Ø406 x Ø229 x 254 mm Min./max. diameter to be ground: 125 mm Grinding wheel width: 254 mm Max. plunge grinding length: 254 mm Regulating wheel dimensions (OD x ID x width): Ø280 x Ø165 x 254 mm Grinding wheel motor power: 30 HP Total power: 34 HP Dcjdpfsydy Emjx Adajf Approx. weight: 5,500 kg Dimensions: 2,600 mm length x 1,200 mm width x 1,200 mm height

Condition: used, Year of construction: 2002, grinding diameter 450 mm grinding length 1500 mm centre height 225 mm Control FAGOR EQUIPEMENT - T1: grinding wheel diameter 500 mm - T2: grinding wheel diameter 400 mm - T6: HF Fischer spindle MFV or MFZ 1224/1242/1260 - T7: HF Fischer spindle MFV or MFZ 1224/1242/1260 - Marposs tool measurement - active longitudinal positioning - Elaso GAP-control on T1 and T2 contactless integrated in the control surface - Elaso GAP internal grinding with fluid sensor for T6 and T7 - semi-automatic balancing by Elaso integrated in the control surface for T1/T2 - tailstock hydraulic with fine adjustment +/- 150 microns - dresser on workpiece spindle side table mounted - dresser on tailstock side table mounted - dresser on upper table - new service- and userfriendly housing SPECIAL EQUPEMENT: Workhead with direct drive - strongly recommended for non-circular grinding - workpiece weight flying max. 75kg - workpiece weight between centres 150kg - water-cooled B-axis with direct drive - center height 225 mm - extremely torsionally stiff - highly accurate positioning - resolution ° - water-cooled Hydrostatic ball screw - x-axis - wear-free, as there is no contact during operation - no loss of precision, even during long-term use at full load and maximum speed Dcodpfx Adeuxfu Nsajf - no friction at low speeds - no friction force backlash when the direction of rotation changes - translates even the smallest rotational movements - no stick-slip effect even at low speeds - no fluctuations in frictional torque due to ball circulation - higher axial stiffness compared to ball screws - significant improvement in damping, resulting in better workpiece surface finish and tool life - no oscillations due to ball circulation - also suitable for high speeds and accelerations - cost-effective alternative to the linear motor with greater precision and significantly lower heat generation - significantly less power dissipation and, as a result, no problems with swarf on permanent magnets New hydraulic unit - optimized temperature control (chiller) - Energy-saving Only one pump controlled by VFD - Pressure monitoring - monitoring of the hydrostatic oil for water content. (Damage to the bellows is recognised and detected prematurely) -fine adjustment +/- 150 microns Paper belt filter 375l – alternative 480l Grinding mist extraction system – emulsion MECHANICAL OVERHAUL -complete machine according to Kellenberger protocoll -new painting ELECTRICAL OVERHAUL - new modern Fagor CNC with BEMA HMI - new electric cabinet - new digital drive technology - replacement of all electrical cables, switches etc. - new absolute external scales in x- and z-axis - new absolute encoder (B-axis) Grinding software BEMA-Standard: - workpiece zeroing - grinding wheel zeroing - dressing diamond measuring - corrections - external and internal surface grinding - external and internal angle grinding (turning of the b-axis, dressing with straight wheel) - external and internal radius grinding (radius dressed on wheel) - semi-automatic traverse grinding - workpiece zeroing - 2 dressing diamonds - 1 dressing blade - dressing roll - 3 flat dresser - corrections - Z-position measurement - GAP control Optional grinding cycles at no extra charge: Profile plunge grinding: - external and internal profile plunge grinding with profile wheel Pr...

Condition: used, Year of construction: 2002, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm dimensions of the machine ca. 3,6/3,5 m Photos of identical machine with centre height 225mm Base: Kellenberger Kel-Varia UR175-1000 Kelco 120 Grinding head UR with T1-T2-T3 Basic equipment: -T1 500mm grinding disc diameter -T2 400mm grinding wheel diameter -Infinitely variable, high-resolution axis -Marposs measuring device for tool measurement -Active longitudinal positioning -GAP on T1 and T2 from ELASO contactless integrated in the control interface Semi-automatic balancing from ELASO integrated into the control interface -Tailstock with manual retraction -MK5 workpiece headstock with short taper DIN 55026 Belt-driven internal grinding device Options at an extra charge: - New high-precision workhead with torque drive - Internal grinding device for high-frequency spindles diameter 120mm -HF internal grinding spindle Fischer MFM-1224/42/31 D-21 -HF spindle with HSK holder 24,000 rpm with integrated GAP sensor. (delivery time) -CNC-controlled C-axis non-circular grinding -hydrostatic threaded spindle in x -new hydrostatic unit with only 1 pump and pressure accumulator thus better energy efficiency. -monitoring of the water content in the hydrostatic system -Suction system Further options available on request Mechanical overhaul: -Complete machine overhauled according to Kellenberger measurement protocol -New service-friendly cab -repainting Electrical overhaul: -New modern CNC CIRCULAR GRINDING MACHINE control with BEMA rough grinding surface -New control cabinet -New drive technology -Replacement of all electrical cables Berus pressure switches etc. -New absolute glass scales in x and z -New absolute rotary encoder (for B-axis) Control system: The grinding software consists of a basic licence and various options that are possible depending depending on the equipment of the machine. Basic software - External and internal pendulum grinding - External and internal plunge-cut grinding - External and internal pendulum grinding - External and internal plunge-cut grinding - External and internal taper pendulum grinding - External and internal radius grinding, radius dressed on disc - Semi-automatic pendulum grinding - Workpiece zeroing - Grinding wheel zeroing - Measuring the dressing diamonds - 2 moulding diamonds - 1 shaped diamond or dressing roll (dressing roll required) - Moulding roller (dressing roller required) - 3 Flat dresser - Corrections - Z-position measurement (probe required) - GAP probing (grinding device required) OPTIONS at an extra charge: Software profile plunge-cut grinding: - External and internal profile plunge-cut grinding with profile disc Profile grinding software: - External and internal profile grinding with straight disc Dcedpfx Adjuxfucsajf Software thread grinding: - Single and multi-start external and internal thread grinding with thread on the disc disc Dressing. Dressing of single and multi-groove discs. Flank angle freely selectable. Trapezoidal thread grinding software: - Additional dressing of trapezoidal threads possible External and internal non-circular plunge-cut grinding: - External and internal non-circular plunge-cut grinding Non-circular grinding software: A prerequisite for non-circular grinding is that the workpiece axis is equipped with a high-resolution rotary encoder so th...

Condition: used, Year of construction: 2020, functionality: fully functional, operating hours: 2,500 h, THIBAUT TC 625 – 5‑Axis CNC Bridge Saw (Used Machine) Description For sale is a THIBAUT TC 625 5-axis CNC bridge saw in very well-maintained condition. The machine is ideal for processing natural stone, quartz composite, ceramics, and similar materials, and is especially suited for kitchen countertop and interior fitting production. Technical Data Manufacturer: THIBAUT SAS (France) Model: TC 625 Machine Type: 5-axis CNC bridge saw Year of Commissioning: approx. 2020 Machine No.: 04.19 Voltage: 400 V / 50 Hz Spindle Power: approx. 13.2 kW Spindle Speed: 0 – 6,000 rpm Blade Diameter: 300 – 650 mm X-Axis Travel: approx. 3,970 mm Y-Axis Travel: approx. 2,300 mm Z-Axis Travel: approx. 500 mm Max. Material Thickness: approx. 200 mm Condition Machine powered – demonstration possible by arrangement Spindle hours: approx. 2,500 h Excellent technical and optical condition Regularly serviced Ready for immediate use Features 5-axis CNC control Tilting worktable 3,600 × 2,000 mm Table adjustment from 0° to 85° Additional unloading table 3,600 × 400 mm Digital camera for slab imaging Tool and material probing system Vacuum lifter up to 500 kg ACS plunge cutting system Tool water cooling Dsdpfxeyuvhfe Adascf Software T'CUT basic software Vacuum lifter manipulation module Vein matching module Contouring and trimming module CAD/CAM software eT'CAM Application Areas Kitchen countertops Bathrooms and washbasins Staircases Processing of natural stone and quartz composite Ceramics and similar materials Sales Information Price: on request Location: Germany Availability: by arrangement Inspection / Test Run: Machine is powered – test possible

Condition: new, Year of construction: 2026, Ultrasonic washing machine- ultrasonic cleaning device with attached oil separator and insulated hinged cover Floor ultrasound, frequency: 25 kHz Power (eff./peak): 750 / 1,500 watts Heating adjustable up to 80 ° C; Power: 4,000 watts Basket dimensions: LxWxH 570x320x250h mm Pool dimensions: LxWxH 650x400x350h mm Dimensions of the device: approx. 1200x550x750h mm max.loading weight of the basket: 30 kg Dodpfedz T Nyex Adajcf 1 piece of stainless steel shopping cart is included Device is on rollers

Condition: used, Year of construction: 2020, Suitable for fully automatic grinding or new toothing and chamfering of HSS and segment circular saw blades as well as solid carbide circular saw blades, jig saw blades / thin-cut saws with chip breaker (diameter from 200-500 mm, tooth pitch from 8-30 mm), in plunge grinding using CBN or diamond grinding wheels. Accessories: Machine with total enclosure and integrated machine room lamp, Loading system including 2 loading mandrels Ø 32 mm, Oil conversion including aerosol extinguishing generator and oil conversion kit, Control cabinet cooling unit, Automatic central lubrication, Marx VTG 0.32 electrostatic mist extractor, HSS/HM fine filter system including external filter unit, with integrated 300-liter coolant tank and cooling unit, Software for all standard curved and pointed teeth, Signal light to indicate operating status, Automatic switching of peripheral speed between CBN and DIA grinding wheels, F-1477 saw blade holder for saws, Various spacers for 32, 40, and 50 mm mandrels, Oil collecting pan. Dcodpfx Asyvgc Nsdasf Saw diameter max: (40) 130 - 850 mm Saw diameter (unmanned): (75) 130-520 mm Tooth pitch: 1 - 40 mm Tooth height: max. 17 mm Number of teeth: 2 - 998 Saw blade thickness: up to 8 mm Loading capacity: 40 saw blades Grinding wheel diameter: (CBN or DIA - 14F1) Ø 200 mm Grinding wheel bore: 32 mm Coolant pressure: 6 bar Coolant tank: approx. 300 L Drive power grinding motor: 3 kW Connected load approx.: 6.5 kW (400 V / 50 Hz) 8.9 kVA Weight approx: 2000 kg Dimensions W x D x H approx.: 2400 x 1700 x 2200 mm colour: Grey

Condition: ready for operation (used), Year of construction: 2008, total height: 2,275 mm, total width: 4,040 mm, overall weight: 13,400 kg, product length (max.): 7,033 mm, number of axes: 2, Centerless grinding machine manufactured in 2008. This DANOBAT 327 MDA features a maximum wheel width for plunge grinding of 500 mm and a peripheral wheel speed of 50 m/s. It has a grinding wheel motor power of 55 kW and a regulating wheel speed that is infinitely variable from 10 to 225 min⁻¹. If you are looking to get high-quality grinding capabilities, consider the DANOBAT 327 MDA machine we have for sale. Contact us for further details. • Gross mass: 14,500 kg (including packaging) • Opening between wheels: 3 to 200 mm (with new wheels) • Maximum wheel width for plunge grinding: 500 mm • Wheel axis height from floor: 1150 mm • Grinding wheel dimensions (OD x width x ID): 650 x 500 x 304.8 mm • Minimum grinding wheel OD: 510 mm • Peripheral wheel speed: constant 50 m/s • Regulating wheel dimensions (OD x width x ID): 350 x 500 x 203.2 mm • Minimum regulating wheel OD: 275 mm • Regulating wheel speed: stepless 10 to 225 rpm Dodpjyvfvhsfx Adascf • Regulating wheel head inclination (part feed): -5° to +5° • Regulating wheel carriage swivel (taper correction): -2° to +5° • Maximum wheel profile depth: 12 mm • Maximum profile inclination (via tracer template): 30° • Dresser feed rate (grinding wheel): 100 to 300 mm/min • Regulating wheel dressing speed: 225 rpm • Dresser height adjustment: mm • Grinding wheel motor power: 55 kW • Regulating wheel motor torque: 8 Nm • Dresser motors (each): 0.55 kW • Grinding head lubrication pump motor: 0.37 kW • Grinding head lubrication system: 100 l capacity, 6 l/min flow, 2 MPa (20 bar) safety valve, oil FD-5 (ISO 3498) • General lubrication system: 6 l capacity, oil G-68 (ISO 3498)

Condition: excellent (used), functionality: fully functional, Handheld circular saw with plunge-cut function 2250 watts Dodpfx Adjyvfpnoascf Cutting depth 85 mm Swivel range 0-60° Weight approx. 6.7 kg As-new condition Shipping available at additional cost!

Condition: excellent (used), Year of construction: 1980, Karstens K11 1000 This Karstens K11 comes from a university environment and was only used very sparingly. All cables and hoses in the wet area have been replaced. It has extremely low operating hours. As we specialize in Karstens cylindrical grinding machines, we can offer you full service (electrical and mechanical) for the machine after purchase. Dodpfx Ajh Rit Esdajcf Technical Data: Centre distance: 1000 mm Centre height: 180 mm Workpiece weight: 70 kg (between centers, cantilevered), 250 kg (between centers) Grinding wheel diameter: 400 mm Workpiece spindle: Morse Taper 4, infinitely variable speed 30–450 rpm, swiveling range 0–90° Tailstock: Morse Taper 4, quill stroke 45 mm Tailstock rest beside Z-axis table Quill force: 200–600 N Table swivel: 12.5 degrees Travel of infeed spindle: 80 mm Rapid traverse: 50 mm Coarse adjustment air cushion: 280 mm External grinding spindle motor: 4 kW Internal grinding spindle motor: 2.2 kW Workpiece spindle motor: 0.55 kW Machine weight: net 3,500 kg Infeed drive by DC motor Air cushion-supported rapid adjustment of the grinding spindle headstock for fast and safe positioning at the grinding station. Separate drives for spindles for external and internal grinding. Fully automatic operation cycle, feed movement controlled via rotary switch: Rapid advance, rapid retraction, grinding mode, feed stop, mym-feed adjustment. Automatic longitudinal grinding cycle Central coolant supply for all grinding stations Workpiece headstock with infinitely adjustable drive for rotating and lockable spindle. Infeed control for longitudinal grinding and plunge grinding, settings for retraction, feed amounts, feeds, spark-out times, idle strokes. Digital readout for X-axis by Heidenhain Paper band filter unit can be offered on request. Comparable to Weiss/ EMAG/ GP-cylindrical grinders/ Studer/ Kellenberger/ Schaudt/ Tschudin/ Tacchella/ Dannobat

Condition: as good as new (ex-display), Year of construction: 2026, Centre height: 181 mm Centre distance: 1000 mm Maximum grindable workpiece diameter: 360 mm Max load cantilevered: 1000 N (100 kg) Max load between centres: 3000 N (300 kg) Z-axis: Table swivel angle: 10° Table drive, hydraulic: 0–4 m/min X-axis: Cross slide travel: 80 mm Rapid traverse (hydraulic): 50 mm Djdpfxetqf Rzo Adaocf Coarse adjustment – air cushion: 280 mm Infeed drive by DC motor Rapid infeed speed: 48 mm/min/Ø Infeed cycle: Plunge grinding / Longitudinal grinding 4 preselectable speeds: mm/min/Ø: 0.01–48 4 preselectable infeed increments: mm: 0.001–0.1 Automatic shut-off during stop-grinding: 0–99 s or 0–99 strokes Stepwise infeed: mm/Ø: 0.001 Grinding headstock universal, swivelling: 0–180° Grinding wheel (OD): D x width x bore: 500 x 100 x 127 mm or 203.2 mm Grinding wheel (face, option) D: 250 x 32 x 76.2 mm Grinding wheel (ID, option) D: 2–250 mm Drive power, external/face: 5.5 (7.5) kW Drive power, internal: 2.2 kW Peripheral speed, external: 35 (50) m/s Grinding wheel wear (OD): mm/Ø: 160 Guard width: 100 mm Grinding spindle diameter: 60 mm Internal spindle mounting: 80 (100) mm Workpiece headstock: Infinitely variable drive: MK 4, 1/min: 30–270 / 50–450 Workpiece spindle lockable Spindle mounting: MK 4/24 mm Spindle nose for flange attachment: MK 4, cylindrical Ø63H6 x 6 mm Headstock swivels on rotating part: 0–90° Tailstock: Quill mounting / Quill diameter: MK 4, 750 mm Quill stroke: 45 mm Quill force, N: 100–800 / 250–1400 adjustable Quill operation: manual (foot switch) Quill fine adjustment: ±40 μm Connections: Total machine connected load: 6.5–10 kW Grinding headstock: 5.5 (7.5) kW Workpiece headstock: 0.55 (1.1) kW Coolant filtration: 0.75–2.2 kW Lubrication pump – guideways: 0.1 kW Hydraulic pump: 1.5 kW Hydraulic tank: 80 l Pneumatics: 6 bar Comparable to: Weiss / EMAG / GP cylindrical grinders / Studer / Kellenberger / Schaudt / Tschudin / Tacchella / Dannobat

Condition: refurbished (used), Year of construction: 2026, Karstens K11 1000 Full Equipment The cylindrical grinding machine has been completely overhauled by PS-Karstens. The machine has been tested and is in very good condition. Since we specialize in Karstens cylindrical grinding machines, we can offer you comprehensive service (both electrical and mechanical) for the machine after purchase. Dcedpfxoh Riwde Adajf Technical Data: Centre distance: 1000 mm Centre height: 180 mm Workpiece weight: 100 kg (unsupported), 250 kg (between centers) Grinding wheel diameter: 400 mm Workpiece spindle: MT 4, steplessly adjustable speed 30–450 rpm, swiveling range 0 - 90° Tailstock: MT4, quill stroke 45 mm, fine adjustment for the quill Quill force: 200-600 N, hydraulically operated via foot pedal Table swivel angle: 10 degrees Infeed spindle travel: 80 mm Rapid traverse travel: 50 mm Coarse adjustment with air cushion: 280 mm External grinding spindle motor: 4 kW Internal grinding spindle motor: 2.2 kW Workpiece spindle motor: 0.55 kW Machine weight: net 3,800 kg Infeed drive by DC motor Air cushion assisted rapid adjustment of the grinding spindle headstock for fast and safe positioning of the grinding position. Separate drive for spindles for external and internal grinding. Fully automatic operation cycle, infeed motion via star dial switch: Rapid approach, rapid return, grinding mode, infeed stop, micron infeed. Automatic longitudinal grinding cycle Central coolant supply to all grinding positions Workpiece headstock with steplessly adjustable drive for live and lockable spindle operations. Infeed control for longitudinal and plunge grinding, input for retraction, infeed amounts, feeds, spark-out times, empty strokes Digital readouts for grinding spindle B-axis, workpiece spindle, X and Z axes from HEIDENHAIN Paper band filter unit approx. 250 L Similar to Weiss / EMAG / GP cylindrical grinders / Studer / Kellenberger / Schaudt / Tschudin / Tacchella / Dannobat / Bahmüller / Fortuna

Condition: refurbished (used), Year of construction: 2026, Karstens K11 650 The cylindrical grinding machine has been completely overhauled by PS-Karstens. The machine has been tested and is in very good condition. As specialists in Karstens cylindrical grinding machines, we can provide you with complete service (electrical and mechanical) for the machine after purchase. Technical Data: Centre distance: 650 mm Centre height: 180 mm Workpiece weight: 100 kg (between centers), 250 kg (supported) Grinding wheel diameter: 400 mm Workpiece spindle: Morse taper 4, infinitely variable speed 30–450 rpm, swiveling range 0–90° Tailstock: MT4, quill stroke 45 mm, micrometer adjustment Quill force: 200–600 N, hydraulically operated via foot pedal Table swiveling: 10 degrees Feed spindle adjustment range: 80 mm Rapid traverse: 50 mm Rough adjustment with air cushion: 280 mm External grinding spindle motor: 4 kW Internal grinding spindle motor: 2.2 kW Workpiece spindle motor: 0.55 kW Machine weight: net 3,800 kg Feed drive by DC motor Air-cushion-assisted rapid adjustment of the grinding spindle stock for fast and precise positioning of the grinding position. Separate drives for external and internal grinding spindles. Fully automatic operating sequence, feed movement controlled via cam switch: Rapid approach, rapid return, grinding mode, feed stop, micron feed. Automatic longitudinal grinding cycle Central coolant supply for all grinding positions Workpiece spindle head with infinitely variable drive for live and locked spindle operation. Dcsdpfxoh Rixxs Adaof Feed control for both plunge and traverse grinding, input for retraction, feed amount, feed rates, dwell times, and idle strokes Paper band filter system approx. 250 L Comparable to Weiss/EMAG/GP cylindrical grinding machines/Studer/Kellenberger/Schaudt/Tschudin/Tacchella/Dannobat /Bahmüller/Fortuna

Condition: as good as new (ex-display), Year of construction: 2026, Center height: 181 mm Center distance: 650 mm Maximum grindable workpiece diameter: 360 mm Max. load (overhung): 1000 N / 100 kg Max. load (between centers): 3000 N / 300 kg Z-axis Table swivel angle: 10° Dcjdpfetqf Sqsx Adaof Table drive hydraulic: 0–4 m/min X-axis Cross slide travel: 80 mm Rapid traverse (hydraulic): 50 mm Coarse positioning—air cushion: 280 mm Infeed drive via DC motor Rapid feed rate: 48 mm/min/Ø Infeed process: Plunge / Longitudinal grinding 4 pre-selectable feed rates: mm/min/Ø 0.01–48 4 pre-selectable infeed increments: mm/ 0.001–0.1 Spark-out during end stop grinding: s 0–99 / 0–99 strokes Jog infeed: mm/Ø 0.001 Grinding spindle headstock—universal, swiveling: degrees 0–180 Grinding wheel (external): D x width x bore mm 500x100x127 or 203.2 Grinding wheel (face, option): D mm 250x32x76.2 Grinding wheel (internal, option): D mm (2–250) Drive power (external, face): kW 5.5 (7.5) Drive power (internal): kW 2.2 Peripheral speed (external): m/s 35 (50) Grinding wheel wear (external): mm/Ø 160 Wheel guard width: mm 100 Grinding spindle diameter: mm 60 Internal spindle mount: mm 80 (100) Workpiece headstock: Infinitely variable drive, MK 4: 1/min 30–270/ 50–450 Workpiece spindle lockable Spindle mount: mm MK 4/24 Spindle nose for flange mounting: MK 4 mm cylindrical Ø63H6 x 6 Workpiece headstock swivels on the rotary part: degrees 0–90 Tailstock: Quill mount / quill diameter: mm MK 4/750 Quill stroke mm: 45 Quill force N: 100–800 / 250–1400, adjustable Quill actuation: manual (foot switch) Quill fine adjustment: ±40μm Connections: Total power requirement of the machine: kW 6.5–10 Grinding spindle headstock: kW 5.5 (7.5) Workpiece headstock: kW 0.55 (1.1) Coolant cleaning: kW 0.75–2.2 Guideway lubrication pump: kW 0.1 Hydraulic pump: kW 1.5 Hydraulic tank: liters 80 Pneumatics: bar 6 Similar to Weiss/ EMAG/ GP cylindrical grinding machines/ Studer/ Kellenberger/ Schaudt/ Tschudin/ Tacchella/ Dannobat/ Bahmüller/ Fortuna

Condition: as good as new (ex-display), Year of construction: 2026, Karstens K11 650 Premium Retrofit Cylindrical Grinding Machine Manufacturer: Karstens Technical specifications: Centre distance: 750 mm Centre height: 180 mm / (250 mm optional) Workpiece weight: 100 kg (between centres) – 250 kg (supported between centres) Grinding wheel diameter: 400 mm or 500 mm (external grinding wheel) Workpiece spindle: MT 4, stepless speed adjustment 30–450 rpm, swivel range 0–90° Tailstock: MT 4, quill stroke 45 mm, quill offset adjustment Quill force: 200–600 N manual, (up to 2500 N adjustable as option) Table swivel adjustment: 12.5 degrees Cross slide travel: 80 mm Rapid traverse distance: 50 mm Coarse adjustment with air cushion: 280 mm External grinding spindle motor: 4 kW / (5.5 kW optional) Stepless speed setting of the grinding wheel via potentiometer Internal grinding spindle motor: 2.2 kW Workpiece spindle motor: 1.1 kW Hydraulic motor: 1.5 kW Lubrication motor: 0.1 kW Hydraulic tank: 80 litres Machine weight: Net 3,500 kg Feed drive via DC motor Air-cushioned rapid adjustment of the grinding spindle head for fast and precise positioning. Separate drive for external and internal grinding spindles. Fully automatic operation, feed movement controlled via handwheel switch: rapid feed, rapid return, grinding operation, feed stop, mym-feed. Automatic longitudinal grinding cycle Central coolant supply for all grinding zones Workpiece headstock with steplessly adjustable drive, with live and lockable spindle. Digital feed control with Siemens panel and Siemens PLC for plunge and traverse grinding, input for retraction, infeed values, feed rates, spark-out times, idle strokes, compatible with traditional Karstens infeed control, with colour Siemens touch panel. Scale in X and Z axis by HEIDENHAIN. Comparable with Weiss / EMAG / GP cylindrical grinders / Studer / Kellenberger / Schaudt / Tschudin / Tacchella / Dannobat / Bahmüller / Fortuna. Dedpjiv Audjfx Adaecf

Condition: as good as new (ex-display), Year of construction: 2026, Karstens K11 1000 Premium Retrofit Cylindrical Grinding Machine Manufacturer: Karstens Technical Data: Centre distance: 1100 mm Centre height: 180 mm / (250 mm optional) Workpiece weight: 100 kg between centres, 300 kg with support Grinding wheel diameter: 400 mm or 500 mm (external grinding wheel) Workpiece spindle: MT 4, infinitely variable speed from 30-450 rpm, swivel range 0 - 90° Tailstock: MT4, quill stroke 45 mm Quill force: 200-600 N manual, (up to 2500 N adjustable = optional) Table swivel: 10 degrees Infeed spindle travel: 80 mm Rapid traverse: 50 mm Coarse adjustment with air cushion: 280 mm External grinding spindle motor: 4 kW / (5.5 kW = option) Infinitely variable speed adjustment of grinding wheel via potentiometer Internal grinding spindle motor: 2.2 kW Workpiece spindle motor: 1.1 kW Hydraulic motor: 1.5 kW Lubrication motor: 0.1 kW Hydraulic tank: 80 litres Net machine weight: 3800 kg Infeed drive via DC motor Air cushion-supported rapid adjustable grinding spindle stock for fast and safe positioning to grinding location. Dodpsh Rimmsfx Adaocf Separate drive for spindles for external and internal grinding. Fully automatic operating sequence, infeed movement via rotary dial switch: Rapid approach, rapid return, grinding operation, infeed stop, mym-infeed. Automatic longitudinal grinding cycle Central coolant supply for all grinding zones Workpiece headstock with infinitely variable drive for both live and lockable spindle operation. New digital infeed control with Siemens panel and Siemens PLC for longitudinal grinding and plunge grinding, inputs for retraction, infeed amounts, feed rates, spark-out times, dwell strokes; compatible with the old Karstens infeed control; with colour Siemens touch panel. Similar to Weiss/ EMAG/ GP cylindrical grinders/ Studer/ Kellenberger/ Schaudt/ Tschudin/ Tacchella/ Dannobat/ Bahmüller / Fortuna

Condition: as good as new (ex-display), Year of construction: 2026, Karstens K11 1000 Premium Retrofit Cylindrical Grinding Machine Manufacturer: Karstens Technical specifications: Centre distance: 1100 mm Centre height: 180 mm (250 mm optional) Workpiece weight: 100 kg between centres (unsupported), 300 kg between centres Grinding wheel diameter: 400 mm or 500 mm (external grinding wheel) Workpiece spindle: MT 4, infinitely variable speed control 30–450 rpm, swivelling range 0–90° Tailstock: MT4, quill stroke 45 mm Quill force: 200–600 N manually, (up to 2500 N adjustable, option) Table swivel: 10° Cross slide travel: 80 mm Rapid traverse: 50 mm Coarse adjustment (air cushion): 280 mm External grinding spindle motor: 4 kW (5.5 kW optional) Infinitely variable grinding wheel speed adjustment via potentiometer Internal grinding spindle motor: 2.2 kW Dcsdpfxeiv Au Ej Adajf Workpiece spindle motor: 1.1 kW Hydraulic motor: 1.5 kW Lubrication motor: 0.1 kW Hydraulic tank: 80 litres Net machine weight: 3,800 kg Infeed drive via DC motor Air cushion-supported rapid adjustment of the grinding spindle head for fast and safe positioning to the grinding position. Separate drive for the spindles for external and internal grinding. Fully automatic operation, infeed movements controlled via rotary selector switch: rapid advance, rapid return, grinding mode, infeed stop, micrometre infeed. Automatic longitudinal grinding cycle Central coolant supply to all grinding points Workpiece headstock with infinitely variable drive for rotating and lockable spindle. New digital infeed control with Siemens panel and Siemens PLC for traverse and plunge grinding; input for retraction, infeed amounts, feed rates, spark-out times, idle strokes; compatible with the original Karstens infeed control; with coloured Siemens touchscreen; HEIDENHAIN scales in X and Z axes. Comparable to Weiss/EMAG/GP cylindrical grinding machines/Studer/Kellenberger/Schaudt/Tschudin/Tacchella/Dannobat /Bahmüller/Fortuna

Year of construction: 2006, condition: like new (used), functionality: fully functional, Zum Verkauf stehen 3 pH-Controller für Dosieranlagen des Herstellers Dosatronic. – geeignet für pH-Regelung und chemische Dosiersysteme – industrielle Ausführung – unbenutzt (Lagerware / New Old Stock) Die Geräte stammen aus einem industriellen Lagerbestand und wurden nie installiert. Geeignet für: – Wasseraufbereitung – Schwimmbadtechnik – Chemische Industrie – Lebensmittelproduktion Dcedpoyw Riqsfx Adajf Zustand: Unbenutzt, jedoch länger gelagert. Funktionsprüfung nicht durchgeführt. Verkauf einzeln oder als Komplettpaket möglich. Preis: 390 € / Stück oder 1.050 € für alle 3 Standort: Slowakei (EU) Versand europaweit möglich For sale: 3 pH controllers for dosing systems (Dosatronic) – suitable for pH control and chemical dosing – industrial version – unused (new old stock) The units come from industrial stock and were never installed. Suitable for: – water treatment – swimming pool systems – chemical processing – food industry Condition: Unused, long-term storage. Functionality not tested. Available individually or as a lot. Price: 390 € per unit or 1,050 € for all 3 Location: Slovakia (EU) Worldwide shipping possible

Condition: excellent (used), Trumpf Type: TruPrint 3000 G02 The machine is in very good condition and has been professionally tested for functionality by a TRUMPF technician at our facility. We provide a 6-week warranty on the machine. Year of manufacture: 11/2017 Beam-on hours: 17,731 Laser Metal Fusion Machine (Metal 3D Printer) Flexible solution for industrial additive manufacturing. The TruPrint 3000 is a universal mid-format machine (LMF / PBF / LPBF) with industrial-grade part and powder management. From now on, you benefit from even greater flexibility, quality, and productivity for your additive serial production: Productivity is nearly doubled, independent of part geometry, and part costs are significantly reduced. Automatic monitoring and calibration of the multi-laser system during the build job ensures optimal quality for printed multi-laser parts. The latest advancements in shielding gas guidance further improve part quality and reproducibility. This is documented in parallel with the build job via Melt Pool Monitoring, allowing compliance with requirements such as those in the medical sector. Highly flexible, the TruPrint 3000 can be adapted to your specific requirements. With a build volume of 300 mm diameter and 400 mm height, it can be used across a wide variety of industries. Depending on the size and complexity of the parts, your workflow preferences, and production volumes, you can flexibly choose between internal or external unpacking—all under inert gas. External unpacking further minimizes the 3D printer’s downtime via simultaneous main-time operations. Technical specifications: TruPrint 3000 Build volume (cylinder): 300 mm diameter x 400 mm height Processable materials: Weldable metals in powder form, such as stainless steels, tool steels, aluminum, nickel-base, cobalt-chrome, copper, titanium or precious metal alloys. Current materials and parameter availability on request. Preheating (standard): up to 200°C Maximum laser power at the workpiece (TRUMPF fiber laser): 500 W Laser spot diameter: 100 - 500 μm Layer thickness (adjustable): 20 - 150 μm Scan speed (powder bed): 3 m/s Build rate: 5 - 60 cm³/h Connections and consumption: Electrical connection (voltage): 400/460 V Electrical connection (current): 32 A Electrical connection (frequency): 50/60 Hz Dedpfx Adevvl I Tjascf Shielding gas: Nitrogen, Argon Design: Dimensions (incl. filter) (W x H x D): 3385 mm x 1435 mm x 2225 mm Weight (incl. powder): 4300 kg The system has been dismantled by the manufacturer, with disassembly records and function logs available. All axes are professionally secured. The system has been used with materials 1.44.04 and most recently with AlSi10Mg. Condition: Used Scope of delivery: (See picture) (Changes and errors in the technical data and listed specifications reserved!) We will be happy to answer additional questions by phone.

Condition: good (used), Year of construction: 2017, functionality: fully functional, machine/vehicle number: 4480, total length: 14,500 mm, total width: 7,800 mm, total height: 3,500 mm, overall weight: 20,000 kg, Reichenbacher Machining Center VISION III-TT-L – 5-Axis, 3-Axis, MBG8, 5x SNA Equipment: 5-Axis Unit with Cardanically Mounted Spindle: Max. speed: 24,000 rpm Nominal speed: 10,000 rpm Power in S1*: 15 kW Max. power in S6: 20 kW Torque in S1*: 14.5 Nm Torque in S6: 19 Nm Nominal voltage: 380 V Nominal current: 37 A Nominal frequency: 380 Hz Speed freely programmable from 0 – 24,000 rpm, in 1 rpm increments Clockwise/counterclockwise rotation selectable via program Driven by frequency inverter Maintenance-free Water-cooled Hybrid bearings Automatic spindle stop in case of emergency stop Orientated stop for thread cutting Tool holder: HSK-F63 hollow shaft taper according to DIN 69893-6 Max. tool length usable from spindle nose: 240 mm Max. tool weight: 6 kg 3-Axis Unit with Vertically Mounted Spindle: Max. speed: 24,000 rpm Nominal speed: 10,000 rpm Power in S1*: 15 kW Max. power in S6: 20 kW Torque in S1*: 14.5 Nm Torque in S6: 19 Nm Nominal voltage: 380 V Nominal current: 37 A Nominal frequency: 380 Hz Speed freely programmable from 0 – 24,000 rpm, in 1 rpm increments Clockwise/counterclockwise rotation selectable via program Driven by frequency inverter Maintenance-free Dcsdjywzq Sjpfx Adajf Water-cooled Hybrid bearings Automatic spindle stop in case of emergency stop Orientated stop for thread cutting Tool holder: HSK-F63 hollow shaft taper according to DIN 69893-6 Max. tool length usable from spindle nose: 240 mm Max. tool weight: 6 kg 8-Spindle Drilling Unit (1 unit): L-Shape, Grotefeld Drill spindles: individually selectable Rotation direction: clockwise/counterclockwise Pitch: 32 mm Power: 2.5 kW Speed: 5,000 rpm fixed Z-axis stroke: +75 mm Holder: D = 10 mm H7 Plunge stroke: 80 mm Grooving Unit (5 units): GROTEFELD Angle Saw Unit F100-S The working/milling stroke is pneumatic. Drive: three-phase motor with multi-ribbed belt LEFT version Drive rotation direction: clockwise/counterclockwise Speed reduction: 1:2.86 – belt drive Power: 2.20 kW – 220-240/380-415 V – 50 Hz Speed: n1 = 2,800 rpm, n2 = 8,011 rpm at 50 Hz Spindle power: 2.2 kW Feed: 150 mm Tool holder: Ø30 x 1.5 mm – 5.0 mm Tool holder rotation: opposite to drive rotation direction Feed force: 2565 N Underfloor Drilling Unit in Machine Bed (1 unit): GROTEFELD Angle Milling Head G06-1.1-P The working/drilling stroke is pneumatic. Drive motor: 1.1 kW 220-240/380-415 V 50-100 Hz Drive rotation direction: clockwise Speed reduction: 1:1.55 gear drive Drive speed: 2,800 – 5,600 rpm Tool spindle speed: 4,340 – 8,680 rpm Tool holder: 1x HI-Q/ERM25 DIN6499-C (8°) For ER25 collet DIN 6499-B Ø0.5–16 mm max. Tool holder rotation direction: clockwise Flange clamping piece: FK45 Feed slide: with pneumatic cylinder and double steel guideways Feed: 80 mm

Condition: used, functionality: fully functional, Year of construction: 2024, operating hours: 404 h, load capacity: 3,500 kg, lifting height: 4,700 mm, free lift: 1,175 mm, fuel type: diesel, mast type: triplex, construction height: 2,450 mm, fork length: 1,200 mm, empty load weight: 5,860 kg, total length: 3,113 mm, drive type: Diesel, construction width: 1,620 mm, Diesel forklift Load center: 500 ISO class: ISO class 3 = 2,500 - 4,999 kg Mast type: Triplex Technical condition: New Front tires Type: Pneumatic Front tires size: 14-17.5-16tl nhs black Rear tires Type: Air Rear tires size: 10-16.5-10tl nhs black Djdpfovdvw Iox Adaecf Battery Volt: 12V Battery Ah: 95Ah Battery manufacturer: Heli Sideshift, heating, load protection grille, full cab, Heli seat H2KE6-80072+armrest+pool belt sideshifter EG 30 SN: 0248 BJ: 05/2023

Year of construction: 2012, operating hours: 3,496 h, condition: excellent (used), functionality: fully functional, Quadra L1 in excellent condition with extremely low operating hours for sale. Dodpfx Aoywpcvjdaecf Available with enclosure upon request! On-site demonstration with profile possible. Quadra L1 pass-through machining center with premium configuration: - 6 spindles, 360° rotatable to machine profiles at any angle - 7.5 meter bar loading magazine - 600mm saw and notching unit - Profile positioning system - MG Pilot handheld controller - 2 steel front conveyors for scrap removal - Slice software - CamPlus / Job software Installation, commissioning, and training can also be provided by us! CNC 12-axis machining center, designed for milling, drilling, and cutting operations on aluminum and light alloys. The QUADRA L1 consists of an automatic tool magazine and a pusher feed system for profiles up to 7500 mm, complete with profile clamping gripper. As the collet moves, the feeder returns to its starting position, allowing the loader to prepare the next profile simultaneously. The central section houses the milling and cutting modules. The CNC 4-axis milling module is equipped with 4 to 6 electrospindles, enabling complete contour machining of the workpiece in any orientation. The CNC 3-axis cutting module features a Ø 600 mm blade with a plunging movement. The QUADRA L1 also includes an automatic outfeed system from the cutting unit to the unloading magazine. The system is equipped with a magazine with cross belts for unloading finished workpieces up to 4000 mm (7500 mm optional). The machining unit can be fitted with an optionally available enclosure, providing sound insulation for the central operational area, which not only protects the operator but also reduces noise emissions. Machine demonstration available!

Condition: used, Year of construction: 2021, Used machine Year of manufacture: 2021 Cutting length: 5300 mm Cutting height: 2200 mm Vertical panel saw for cutting sheet-type wood materials such as chipboard, MDF panels, veneer panels, multiplex, etc. Base machine Completely welded frame with extremely high rigidity Precise guidance of the saw beam / saw unit for accurate cutting. Automatic feed for vertical and horizontal cuts. Cutting depth: max. 60 mm Saw beam Sturdy saw beam guided on precision rails. Pneumatic latching of the saw beam in the upper and lower positions. Electric monitoring during vertical cuts Saw unit Smooth and ergonomic operation for plunging and retracting the saw unit. Plunge lever can be folded down from the upper position for precise entry. Generously dimensioned levers for easy swiveling. Housing cover opens the complete saw unit for easy tool changes, including ProLock quick-release chuck. View opening: riving knife can be retracted Automatic functions Automatic plunge, cut-through, retract, and stop or Automatic plunge, cut-through, retract, and return Shortened return travel (selector switch) The shortened return travel of the saw beam prevents unnecessary travel paths of the saw unit (short workpiece positioned on the right) Speed control: infinitely variable from 6 - 24 m/min Cutting depth: max. 60 mm Control panel Efficient operation of the machine. Ergonomically mounted at eye level. Lower workpiece support Stable, wear-free stainless steel support. Support up to the cutting line: narrow workpieces cannot tip or fall through. Extraction Effective extraction with two ports: saw unit Ø 120 mm, frame end Ø 100 mm (for TRK version) Lifting roller transport system: Manually raiseable and lowerable rollers for easy and gentle panel transport. Dcedpfoyuld Aex Adaef Measuring tape For dimension display in horizontal cutting with three manual measurement displays: Absolute measurement from the lower workpiece support Absolute measurement from the middle workpiece support Series cuts from the top edge of the panel Powerpackage The package consists of the following options: 1. TRK extraction system 2. SuperCut scorer 3. Vertical digital display 4. Stepless speed regulation Saw unit 7.0 kW, 1100–5500 rpm, 400 V, 50 Hz Incl. HW circular saw blade Ø 250 x 30 x 3.2 mm, Z 48, hollow-flat tooth TRK system according to CE guidelines SH 2200 (less than 2 mg fine dust/m³ of air) – mandatory for all CE-required countries (extraction system provided by customer) Pneumatic shifting grid Continuous shifting grid over the entire machine length for stable workpiece support. Automatically, pneumatically retracts during horizontal cuts. Prevents the shifting grid from being cut during horizontal cuts. Digital measurement display for horizontal cutting on the control panel Incl. electric fine adjustment Display of: Absolute measurement from the lower workpiece support OFF-Set measurement from the middle workpiece support Series cuts from the top edge of the panel Saw blade compensation (saw blade thickness can be individually programmed) If the unit is operated via the brake at the ba... (text cut off)

Condition: used, Technical details: x-travel: 800 mm y-travel: 800 mm z-travel: 800 mm Dedpfx Ajwix E Redascf turning speeds: 35-10.000 1/min spindle: 37 / 30 kW max. torque on the spindle: 525 / 206 Nm Tool bore: BT 50 rapid traverse: 60 m/min tool change unit: 160 Pos. size of pallet: 500 X 500 mm control: MAZATROL 640M Nexus c-axis: 0,001° x 360.000 workpiece weight: 1.000 kg workpiece height max.: 1.000 mm interference area: 900 mm 2 pcs. horizontal machining centers (HCN 6000 + HCN 6000-II, 2008), interlinked with pallet pool (16 pallets) MAZAK FMS, 2 pallet changer, chipconveyor, coolant device with internal coolant supply, accessories for both machines: 18 pallets, approx. 300pcs. toolholders, miscellaneous devices for workpiece-clamping... *

Condition: used, Technical details: x-travel: 800 mm y-travel: 800 mm z-travel: 800 mm turning speeds: 35-10.000 1/min spindle: 37 / 30 kW max. torque on the spindle: 525 / 206 Nm Tool bore: BT 50 rapid traverse: 60 m/min tool change unit: 160 Pos. size of pallet: 500 X 500 mm control: MAZATROL 640M Nexus c-axis: 0,001° x 360.000 workpiece weight: 1.000 kg workpiece height max.: 1.000 mm interference area: 900 mm 2 pcs. horizontal machining centers (HCN 6000-II + HCN 6000, 2005), interlinked with pallet pool (16 pallets) MAZAK FMS, Dcedowix Hhopfx Adajf 2 pallet changer, chipconveyor, coolant device with internal coolant supply, *

Condition: used, Year of construction: 2020, Overview This RINK automatic screw cap remover (unscrewer) was manufactured in 2020 and is designed for the automatic removal of screw caps from returnable glass bottles before the containers enter the bottle washing process. The machine was installed in a high-capacity returnable glass bottling line with a capacity of approximately 2,000 crates per hour. Systems of this type are typically positioned upstream of the bottle washer to ensure that bottles enter the cleaning process without closures. The machine is configured for 0.75 L GDB bottles in 12-bottle crates and includes format equipment for different crate variants. The system operates with cross-flow crate transport and a crate infeed direction from left to right. The installation includes a cap discharge system and blower unit for removing closures from the bottles. The machine was built with modern electrical components and is supplied with technical documentation. Technical Data Manufacturer: RINK Machine type: Automatic screw cap remover (unscrewer) Model: KM 790 / 4K-3K QL Year of manufacture: 2020 Capacity: approx. 2,000 crates per hour Application: Automatic removal of screw caps from returnable bottles before bottle washing Bottle format: 0.75 L GDB bottle (height approx. 295 mm) Crate formats: 12-bottle Pool N2 crate (400 × 266 × 333 mm) 12-bottle individual crate (395 × 295 × 355 mm) Crate transport: Cross-flow crate transport Infeed direction: left → right Transport height: approx. 700 mm (max. 750 mm adjustable) Dimensions: Length: 2,700 mm Width: 1,400 mm Height: 2,950 mm Weight: approx. 3,000 kg Electrical equipment: Danfoss frequency converter Standard electrical configuration Additional equipment: Cap transport system Blower unit Technical documentation available Condition: Used Availability: On request Dsdpfx Adeytphceaecf