Used Plaster Worm for sale (365)

Condition: new, Electric dehumidifier/construction dryer for commercial use. For drying rooms, dehumidifying cellars, etc. and for drying e.g. concrete, masonry, plaster, screed. Refrigeration unit with rotary piston compressor and capacitor motor 230 V, 50 Hz, 900 W, with electronic defrosting, for continuous operation. Very quiet operation. Dehumidification capacity max. 50 l/24 h, air volume max. 265 m3/h. Electronic control unit with illuminated large control panel and memory function. Electronic hygrostat. Air filter. Internal 7.7 l condensate container. In sturdy plastic housing with castors. In cardboard box. Bedpfx Acstty Rajysdi Dehumidification capacity: ≤ 50 l/24 h Air volume: ≤ 265 m³/h

Condition: used, Year of construction: 1995, Overview This grinder, type: Seydelmann AD 114 was built in 1995 in Germany. The machine is in good conditon and ready to use. Technical Details 114 mm hole plate diameter 2 speed working worm 2 speed feeding worm Installed power: 9 kW Voltage: 400 V, 50 Hz Scope of delivery grinder | Seydelmann | AD 114 | 1995 Bdjdpfexcb Huox Acyei

Condition: used, Rotary Table WMW Type D 315 k Serial No.: 16508 Table diameter: 315 mm Table height: approx. 135 mm Transmission ratio: 90:1 - Hand crank with indexing plate and scissors - Scale ring for reading at the crank Bdedpfx Acoxcbpieysi - Readable degree scale on the rotary table - Swing-out worm for direct indexing - Clamping via clamping screw - 14 mm T-slots in the table plate - Universal joint drive - Built-in indexing plate: 17-25-30-39-47-57 - Rotary table drive suitable for WMW HECKERT console milling machine Type FU 315 E, possibly also for FU 400 E - Dividing head (indexing plate = 20) suitable for WMW HECKERT console milling machine Type FU 315 E, possibly also for FU 400 E Weight: 145 kg Good condition

Condition: used, Year of construction: 1997, Technical details: max. module: 7 weight of the machine ca.: 5 t worm grinding diameter: 280-350 mm width of grinding worm: 84-104 mm Bdsdpfoxb Arpox Acyoi min. number of teeth: 6 max. number of teeth: 600 max. top circle diameter: 360 mm max. workpiece weight: 60 kg without filter *

Year of construction: 2024, condition: new, functionality: fully functional, controller manufacturer: Siemens, conveyor belt length: 2,200 mm, Equipment: CE marking, Drying Mate Belt Conveyor Dryer No. 10093 – New, Unused, In Stock (Vilnius, Lithuania) Belt dryer designed for mealworm larvae and other porous, non-fluent products suitable for conveyor drying. Purchased in 2024 for €83,000, never installed (solved the need via outsourced services) – still in original packaging, unused, CE-marked, and ready to ship. Includes complete operation manuals and technical documentation. Key specs: Max. drying temperature: 200 °C Evaporation capacity: 4 kg/h Conveyor belt: 2.2 m length × 300 mm width (woven glass fiber, Teflon coated) Adjustable drying time: 15–100 min Electrical heating: 4.6 kW (expandable) Siemens PLC with HMI touchscreen Full stainless steel AISI 304, hygienic design, EC 1935/2004 compliant Dimensions: 1.6 × 0.6 × 2.4 m Power: 400 V, 50 Hz Bdedpfxjxfrxge Acyoi Condition: New, unused, in original packaging. Availability: Ready to ship immediately.

Condition: used, Used Filler KHS and Angelus PRO 120L Seamer for cans up to 40000 cph Introduction to the Filler KHS and Angelus 120L Seamer: Bdjdpfx Acovgvvcoyoi In the dynamic landscape of beverage packaging, the demand for efficient and reliable canning solutions is paramount. Consequently, enter the Rebuilt KHS Can Filler paired with the Angelus 120L Seamer, a formidable duo tailored for high-speed operations. Originally manufactured in 1990 (filler) and 1993 (seamer), this system underwent a comprehensive rebuild in 2019, ensuring peak performance and longevity. Exceptional Capabilities Designed to cater to the stringent requirements of the industry, this powerhouse combination of the Filler KHS and Angelus 120L Seamer boasts exceptional capabilities. With 94 filling valves and 12 seaming heads, it delivers unparalleled efficiency, accommodating cans up to 40000 pieces per hour. Notably, ideal for 202/204 x 602 (0.35L) formats, it excels in handling cold-fill CSD beverages with precision and consistency. Comprehensive Rebuild of the Filler KHS and Angelus 120L Seamer The rebuild process of the Filler KHS and Angelus 120L Seamer left no stone unturned, rejuvenating every aspect of the system for optimal functionality. The stainless-steel painted cast iron frame provides robust support, complemented by a new slew ring for enhanced stability. Furthermore, the complete replacement of can handling parts ensures seamless operation, while a height adjustment system with a drive guarantees precise alignment. Enhanced Components Critical components such as fill tubes, trip levers, and tulip actuators were replaced in the Filler KHS and Angelus 120L Seamer. Additionally, the installation of a closing cam and wear strip package ensures smooth sealing of cans. Moreover, the system’s reliability is further fortified with new infeed belt drive and worm drive gearboxes, facilitating uninterrupted production cycles. Technological Advancements for Filler KHS and Angelus PRO 120L Seamer Embracing technological advancements, the rebuild incorporates modern features including CIP cup assemblies and a new center column, enhancing sanitation and ease of maintenance. Furthermore, a Filler control panel equipped with Allen Bradley controls empowers operators with an intuitive interface and seamless operation. Moreover, the system is configured for air-veyor infeed, optimizing material handling efficiency. Operational Precision It’s imperative to highlight a crucial operational detail: the filler operates counterclockwise, while the seamer functions clockwise. This synchronized yet opposing rotation ensures seamless integration and optimized performance throughout the canning process. Consequently, this directional specificity underscores the meticulous engineering behind the system, contributing to its reputation for precision and reliability in the industry. Efficient Workflow With this synchronized rotation, the filler and seamer work in harmony, facilitating efficient can handling and sealing.

Condition: new, Continuous drilling capacity: 25 mm Normal drilling capacity: 30 mm Thread cutting capacity: M 12 Spindle: MK 3 Drilling depth: 135 mm Infinitely variable spindle speeds: 150 - 3000 rpm Table size: 460 x 360 mm Weight: 225 kg Power supply: 400 volts, 50 Hz Equipment: Bdjdpfod R Acbsx Acysi - Thread cutting device - Digital display for speed as standard - Coolant device - LED machine light - Continuously variable speed adjustment - 24 V electrics - Base plate with T-slots - Drilling table adjustable via rack and worm gear and can be swiveled around the column - Emergency stop button - Full motor protection - Star grip - CE compliant

Condition: good (used), Gearboxes, spur gears, angle gears, worm gears, bevel gears -Manufacturer: Poggi, gearboxes, bevel gears -Translation: 1:2 -Shafts: Ø 24 x 50 mm Bdjdpfx Acexbdktsysi -Number: 1x gearbox available -Price: per piece -Dimensions: 252/245/H85 mm -Weight: 4.7 kg

Condition: ready for operation (used), Year of construction: 2006, functionality: fully functional, power: 11.03 kW (15.00 HP), overall weight: 1,500 kg, input voltage: 380 V, ejection height: 1,000 mm, opening width: 600 mm, rotor length: 1,000 mm, rotary shear 2 shafts - 2 motors 15kw and 12kw - inversion in case of jam - shredding chamber 1100 x 900 - thickness of new knives 30 - 4 tons - large loading hopper - possibility of loading very versatile and very powerful, can pre-grind organic matter for methanizers, copper cables, lumps, plaster, BA13, D3E, plastics, wood, bumpers, bottles, metals, hollow bodies, etc. use to grind up sick calves at the renderer. Bsdsh Diwuspfx Acyjdi

Condition: used, Year of construction: 2007, control Siemens Sinumerik 840 D weight 57.000 kg voltage 400 V Gleason PFAUTER CNC gear hobbing machine P 2400/2800 for gear cutting of cylindrical and worm gears as well as all other regularly occurring rollable profiles and shapes on the cylindrical workpiece circumference. Large gear hobbing machines from Gleason offer maximum productivity for roughing and finishing cylindrical gears for many industries: wind turbines, industrial gearboxes, mining and shipbuilding, gear machining and many more. The power range of the drive takes future tool developments into account. Of course, the gear hobbing head drive is also backlash-free. These machines are particularly well suited for use with state-of-the-art, cutting materials, regardless of whether dry or wet machining is preferred. The machine can be used for dry or wet machining and is also equipped with the appropriate chip conveyor for both machining methods. The machine is equipped with an internal profile milling head as a motorised Bdedpfowzyp Iox Acysi milling head. --> Working range and technical data Nominal workpiece diameter: 2.400 mm --> Largest millable diameter approx.: 2.800 mm --> Smallest/largest distance between cutter and workpiece axis: 100/1.200 mm --> Largest axial slide travel (special design): 1.300 mm --> Largest clampable cutter (internal milling head): --> Diameter max: 440 mm --> Max. cutter width: 90 mm --> Swivel range of the internal profile milling head/vertical axis: +/- 15° --> Milling mandrel taper: HSK-B160 --> Maximum milling cutter travel: 300 mm --> Table diameter: 2.500 mm --> Part wheel diameter: 2.200 mm --> Table bore --> Diameter: 800 mm --> Depth: 875 mm --> Maximum table load approx.: 40.000 kg --> Max. feed and rapid traverse speeds: --> axial (Z-axis): 4.000 mm/min --> radial (X-axis): 3.000 mm/min --> tangential (Y-axis): 3.000 mm/min --> Milling cutter cooling lubrication device/electric centrifugal pump: approx. 150 l/min --> Increased drop height of magnetic chip conveyor: 1,600 mm --> Increased main stand: 1,300 mm axial slide travel --> Internal profile milling head as motor milling head instead of standard motor milling head --> Max. millable profile depth in steel with approx. 600 N/mm² strength: approx. 65 mm --> Infinitely variable milling speed: 50 - 150 min?¹ --> Max. milling cutter diameter: 440 mm --> Min. milling cutter base circle diameter: 310 mm --> Max. milling cutter width: 90 mm --> Min. internal diameter at 0° bevel angle: 800 mm+) --> Max. workpiece height at 0° bevel angle: 600 mm --> Max. workpiece ring thickness (including clamping device): 500 mm

Condition: new, Year of construction: 2025, functionality: fully functional, nominal power: 5 kW (6.80 HP), 5 kW 7.5 HP Cutting height 200 mm Tiltable up to 60° to the left, up to 30° to the right using a hand crank from the front Cutting height when tilted at 45°: 140 mm Cutting width 420 mm; cutting width when swiveled at 45°: 290 mm Swivable up to 60° to the left, up to 45° to the right Incl. saw blade for wood 6,000 mm heavy-duty crosscut roller conveyor, mounted on the left, stop-slider adjustable from the machine with handwheel, pneumatically lockable, length digitally readable, digital display in 230V version 4,000 mm heavy-duty infeed roller conveyor, mounted on the right Bodpfjdxw U Isx Acyedi Machine tiltable on both sides from the front using hand crank and worm gear Various options available on request, e.g. greater cutting height, material clamping, laser cutting guide

Condition: used, Year of construction: 1997, sheet width 3020 mm plate thickness 4.0 mm Bdjdpfsxacgkjx Acyji Opening width / upper beam 350 mm Adjustment folding beam 100 mm adjustment of lower beam 80.0 mm bending angle max. 130 ° work height max. 900 mm Control SIEMENS OP 7 voltage 400 V total power requirement 9.5 kW weight 5400 kg range L-W-H 4300 x 2400 x 1780 mm Furnishing: - SIEMENS - PLC control model OP 7 * Bending process as a controlled, fully automatic, or semi-automatic workflow can be selected * Bending angle adjustment electronically preselectable 0-135 ° - electr. / controlled backgauge X = 1000 mm * with large sheet metal support surface - heavy welded construction - all drives both. via worm gear - Motorized adjustment of the bending beam - large adjustment range of the cheeks - hydraulic upper tool clamping - Insert / bending tools - Operation manual * Special accessories included: - separate split goat foot splint H 170 mm * Machine video: - ?v=C3rwhUDtOKw

Condition: like new (used), functionality: fully functional, machine/vehicle number: FDL-150-100E/NC, total length: 1,200 mm, pressing force: 150 t, table width: 800 mm, working height: 600 mm, clearance between the columns: 1,250 mm, Equipment: documentation/manual, safety light barrier, DOUBLE-COLUMN HYDRAULIC PRESS WITH TWO SIDE CYLINDERS FOR PRE-PRESSING AND PRESSING OF ROTORS AND STATORS, AND A CENTRAL CYLINDER FOR ROTOR SHAFT EXTRACTION, AS WELL AS FOR SHAFT EXTRACTION IN CASE OF REPAIR It features an extendable table for stacking and handling rtors and stators. It meets and satisfies all essential safety and health requirements according to CE regulations. STRUCTURE AND TABLES • Consists of a rigid fixed bench welded structure made exclusively from S355JR steel. • Stabilized and machined at the end of the welding process to ensure perfect parallelism and precision. • Calculated and designed using finite element software. • Mechanically movable grooved table measuring 1200 x 800 mm with a stroke of 1,200 mm, equipped with a worm gear reducer and a 0.5 HP electric motor with brake. • Central drill on the table with a diameter of 250 mm and a maximum depth of 550 mm. • Useful lifting capacity of the table for moving 4 tons. • Movement speed of 30 mm/sec. • Front interior width of 1250 mm (space between columns). • Working height of 600 mm. MAIN CYLINDERS: 150 TN • Two 75-ton hydraulic cylinders (150 tons total), with a stroke of 1200 mm connected by a plate with a central hole of 250 mm in diameter. • Maximum useful height of the cylinder plate: 1,440 mm. • Minimum useful height of the cylinder plate: 200 mm. ABSTRACTION CYLINDER • One 100-ton central cylinder with a stroke of 1200 mm. • Designed to accommodate an abstraction clamp, end of the rod threaded to M 35.150 x 40 mm length. Bjdewpg Awopfx Acyodi • Maximum useful height of the abstraction cylinder: 1600 mm from the root of the rod thread. • Minimum useful height of the abstraction cylinder: 400 mm from the root of the rod thread. HYDRAULIC GROUP • Two-speed hydraulic group with 5.5 HP power “Siemens Motor”, with automatic disconnection of high speed and independent speeds. Maximum pressure: 250 bar. • Pressure regulation system using proportional valves. • Air-oil cooler. • Temperature sensor. • Hydraulic group located on the right side. ELECTRICAL INSTALLATION AND SAFETY • Equipped with a SIEMENS mod. SIMATIC S7 1200 safety PLC and a 12” HMI touchscreen mod. MTP with 99 memory slots allowing adjustment of pre-pressing power, pressing, calendering, and stroke of the pressing and extraction cylinders, as well as the holding times during processes. • Electrical and hydraulic maneuvers are redundant and self-controlled. They include an additional safety block and self-control devices for operation and safety. Includes verification and certification of correct operation and safety distance for photoelectric cells. • The electrical panel includes a selector for choosing the type of work in manual, semi-automatic, or automatic position and a selector for high-speed or low-speed operation. • Operation is performed via a two-hand low-voltage electrical pushbutton. • All installed electrical materials are Siemens, including relays, contactors, main motor, etc. • Ready for Industry 4.0. • To ensure safety, it includes category IV photoelectric barriers located in the front work area, two fixed side guards, and a practicable rear guard with a magnetic disconnection detector.

Condition: good (used), Gearboxes, spur gears, angle gears, worm gears, bevel gears -Manufacturer: Marzorati, gearbox type A 150 with magnetic filter -Shafts: Ø 32 x 45 mm Bdodpfexaz Rzox Acyoi -Dimensions: 310/275/H200 mm -Weight: 19.6 kg

Condition: good (used), Year of construction: 2006, functionality: unexamined, machine/vehicle number: 06 03 1000, Country of manufacture: CH Voltage: 400V Dimensions: 1200 x 1650 x 2050 mm Net machine weight: 1900 kg TECHNICAL SPECIFICATIONS Machine: Disc rotation speed: 0–110 rpm Maximum drive power for discs: 2 kW Maximum upper disc load: 20 daN Disc diameter: Ø 450 mm Internal drive rotation speed: 0–115 rpm Maximum internal drive power: 0.5 kW Disc drive motors (continuous motor): Type: DC motor Armature voltage Ua: 260 V Field voltage Ue: 340 V Rotation speed: 3110 rpm Power: 2 kW External ventilation: 220V, 50/60 Hz Bsdow T Tpdjpfx Acyedi Internal drive motor: Motor type: smooth operating mid-position control motor Armature voltage Ua: 260 V Field voltage Ue: 340 V Rotation speed: 3110 rpm Power: 0.5 kW Separate ventilation: 220V, 50/60 Hz Vertical drive motor: Type: stepper motor Steps per second: 50 Torque: 1100 Nm Crown gear adjustment: Type: AC brake motor 2 positions Voltage: 380V / 50 Hz Rotation speed: 700–1400 rpm Power: 0.25/0.37 kW DC brake: 24V Braking torque: 16 Nm Power converters: Input voltage: 380V / 50 Hz Induced voltage: 270 V Field voltage: 340 V Worm gear reduction ratio (internal drive): Ratio: i = 1 : 30 Worm gear reduction ratio (lower system): Ratio: i = 1 : 15.5 Worm gear reduction ratio (upper system): Ratio: i = 1 : 15.5 Operating pressure: Air circuit: 6–7 bar Lapping fluid pump: Connection voltage: 380V 50Hz Rotation speed: 2600 rpm Flow rate: 57 L/min Protection: IP 44 Control and measurement device: Measurement range: 6 (±3 to ±11000 mm) See details in Millitron user manual Inductive probe: Measurement range: ±2 mm Setpoint adjustment device: Display: 4 digits Unless stated otherwise, all technical data are provided without guarantee and subject to change or error.

Condition: used, Year of construction: 1980, inner taper of milling spindel ja collet diameter ja turning speed range 800 U/min Worm milling head for beetle 140 + 135 Bdsdpfx Aow N S D Ejcyei No. 4003 Type.140

Condition: used, Year of construction: 1998, saw blade diameter 350 mm cutting diameter 110 mm capacity 90 degrees: flat 180 x 85 mm capacity 45 degrees: round 105 mm capacity 45 degrees: flat 130 x 85 mm capacity 60 degrees: round 105 mm capacity 60 degrees: flat 90 x 85 mm turning speeds 9-18-36-74 U/min vice max. 180 mm Control IMET CNC total power requirement 1.5 / 2.2 kW weight 710 kg range L-W-H 2000 x 1100 x 2000 mm Current new price approx. 25.000 euros Special price on request Circular saws are used to cut thin-walled tubes and profiles. Clean, precise Bjdpfx Acsxabzyeyedi cut edges are achieved with the circular saw. Fast sawing and easy miter adjustment are the advantages of the circular saw. Basically, you should also pay attention to the correct cooling of the materials. Cooling lubrication is essential for metallic materials. Cooling lubrication is not required for non-metallic materials such as plastic, brass or cast iron. Choosing the right tooth pitch is decisive for the optimal use of metal circular saw blades. For the material cross-section to be machined in connection with the material quality. Furnishing: - CNC fully automatic / vertically guided metal circular saw - swiveling CNC control, front left * Entry of parameters such as quantities and material lengths - Precision prism guide of the gear head, laterally adjustable - Hydro-pneumatic control of the saw unit - with automatic material feed & quantity specification * electro-pneumatic material feed unit - Smooth-running, powerful worm drive * with large transmission ratio - with miter adjustment via large turntable - continuous saw blade lowering - pneumatic material clamping - Stable base with built-in automatic cooling and large chip drawer - Micro spray device for stainless steel cuts (untested) - Safety device for feed device (hood) - Saw blade guard - User manual (PDF) * Machine link : ?machineno=1008-9164086

Condition: used, functionality: fully functional, pressing force: 150 t, pressure: 250 bar, Double-column hydraulic press equipped with two side cylinders connected by a platen for the pre-pressing and pressing of rotors and stators, and a central cylinder for the extraction of the mandrel and fitting of the rotor shaft, as well as shaft removal during repair operations. Features a retractable table for stacking and handling rotors and stators. MAIN CYLINDERS 150 t - 2 hydraulic cylinders of 75 t each, with a stroke of 750 mm, joined by a slotted platen with a central bore of 250 mm diameter. - Maximum usable height between cylinder platens: 1,300 mm. - Minimum usable height between cylinder platens: 550 mm. EXTRACTION CYLINDER - 1 central cylinder of 80 t, with a 1,200 mm stroke. - Prepared to fit an extraction clamp; rod end threaded M 35 x 1.50 pitch, 40 mm length. Bdedpfjxc Ekdex Acyei - Maximum usable height of extraction cylinder: 1,300 mm to the root of the rod thread. - Minimum usable height of extraction cylinder: 100 mm to the root of the rod thread. TABLE AND STRUCTURE - Mechanically movable slotted table, 1,200 x 800 mm, with a 600 mm stroke, fitted with a worm gear reducer and 0.5 HP electric motor with brake. - Central bore on the table: 250 mm diameter; max. depth 550 mm. - Effective lifting capacity of the table for movement: 4 t. - Table traverse speed: 2,600 mm/min. - Internal front width: 1,250 mm. - Working height: 600 mm. HYDRAULIC POWER UNIT - Two-speed hydraulic unit, 5.5 HP, with automatic disengagement of rapid speed and independent speeds. Maximum pressure: 250 bar. - Digital control for maximum force during pre-pressing, pressing, and fitting; digital tonnage display. Pressure adjustment system via proportional valves. - Selector for approach and measuring speeds.

Condition: good (used), Gearboxes, spur gears, angle gears, worm gears, bevel gears -Manufacturer: Poggi, gearboxes, bevel gears -Shafts: Ø 24 x 50 mm -Number: 3x gearbox available -Price: per piece -Dimensions: 250/250/H86 mm Bdodpfx Asxazpqscyoi -Weight: 4.9 kg/piece

Condition: used, Year of construction: 1989, max. wheel diameter 400 mm gear width 275 mm max. module 6 Overall size 300x330x245 cm weight of the machine ca. 5,5 t Specification: Max wheel diameter: 400 mm Min module: 1 Max module: 6 Bdsdpfx Aju A I Elscyoi Table diameter: 370 mm Max wheel diameter: -With counterstay: 340 mm -Without counterstay: 400 mm Max axial offset: 275 mm Max tangential adjustment: 100 mm Tooth helical angle: 45 degrees Max cutter diameter: 145 mm Max hobbing length: 170 mm Hob turning speeds capacity: 63-180 U/min Feeds infinitely variable axial: 0,2-10 mm/U Feeds infinitely variable tangential: 0,1-5 mm/U Radial for spur gears: 0,1-4 mm/U Radial for worm gears: 0,025-1 mm/U Rapid traverse axial: 500 mm/min Rapid traverse tangential: 250 mm/min Radial for spur gears: 400 mm/U Radial for worm gears: 100 mm/U Motor power: 7.4 kW

Condition: ready for operation (used), Year of construction: 1996, filling capacity 400 Liter Usable Volume 300 Liter filling amount max. 850 kg workpiece sizes max. 850 x 200 mm Individual weight of workpiece max. 30 kg turning speeds 4.0 - 15.0 U/min Inner drum width 925 mm drive motor 380 V weight of the machine ca. 1950 kg. range L-W-H 3100 x 1600 x 2000 mm good / well-maintained condition (!!) - in checked conditions - machinevideo - ?v=xxnCddCmXe4 Description: - LIMA cleaning machines * for long concrete formwork parts, formwork clamps Bdsdpexaa Ulefx Acysi * for flame-cutting parts, plasma-cutting parts, laser-cutting parts * for punching and sawing parts - environmentally friendly, cost-saving, low-noise - drive with 5-fold V-belt via worm gear - maintenance-free spherical roller bearings - entire machine is highly soundproofed - dust extraction installed as standard - drum running time adjustable - speeds variably adjustable - the drum can be moved into any position using jog mode - space-saving thanks to compact design - extraction system built into the machine - single-lever drum quick release - machine bearings on vibration dampers - spacious unloading area, suitable for Euro standard containers - free access for forklifts or pallet trucks Working method: - the parts to be processed are moved by their own friction . deburred, descaled and derusted. - the closed design reduces the noise generated during deburring . to just 68 - 72 dB(A). - a direct-acting dust extraction system automatically removes . the dust generated during processing. - the machine can also process oily punched and sawn parts. - during this processing, additional sawdust is added to the drum. - a time delay switch switches the dust extraction system on individually. - the parts are thus deoiled and dried first. - only after this process does the dust extraction system switch on . automatically to suck the sawdust out of the drum. - by specifying the drum speed, optimal processing is guaranteed. - the LIMA-400 L deburring machine can be set up anywhere, . provided there is a solid surface/foundation. - after the work is complete, the drum remains in the position. . so that the drum flap can be opened quickly. - one work cycle takes about 20 minutes.

Condition: good (used), Gearbox, spur gear, angle gear, worm gear -Manufacturer: Ruhrgetriebe, gearbox type SN 3 B -Translation: i= 12 : 1 -max. torque: 13.5 Nm -Shafts: Ø 12 x 30 mm -Number: 3x gearbox available Bdedpfxjxaziqj Acyoi -Price: per piece -Dimensions: 130/114/H75 mm -Weight: 0.9 kg

Condition: new, saw blade diameter 520 x Ø 50 mm cutting diameter 200 mm cutting length 420 mm Cutting height at 45° 140 mm dimensions of saw-blade 520x3,6/3,0x50 mm turning speeds 2800 U/min Dust suction hood 100 mm total power requirement 3,0 kW Bedpfx Acjxaaxdeyjdi weight of the machine ca. 310 kg. range L-W-H 1400 x 900 x 1650 mm - Crosscut and miter saws for crosscuts - Miter adjustment on both sides (60°/45°), with fixed stops - Shift cut on both sides (60°/45°), with fixed stops - Stable cast iron construction - Precise ball bearing guidance of the tool slide hardened and welded steel shafts - manual saw feed - Saw blade infinitely adjustable in height - socket for opt. suction Furnishing : - 3.0 kW motor for ALU cuttings - Saw blade can be tilted via handwheel and worm gear (shift cut) - Saw blade diameter 520 mm - Saw blade mounting hole 50 mm - Saw blade speed 2,800 rpm - 400 Volt / 3 kW (S6/40%) motor with brake and automatic. Star-delta motor circuit - Machine weight approx. 250 kg Cutting data : - Cutting length at 90° = 420 mm - Cutting height at 90° = 200 mm - Cutting length at 45° = 295 mm - Cutting height at 45° = 140 mm Special accessories included: - HM saw blade 520x3.6/3.0x50 mm - Hydraulic feed brake, continuously adjustable - Pneumatic material clamping from above best. from : 2 vertical clamping cylinders adjustable with lever valve - pneumaschine saw blade spray device - Machine can be tilted from the front on both sides using a hand crank - Machine stand

Condition: excellent (used), Geared motor, electric motor, electric geared motor, worm geared motor, bevel geared motor, bevel geared motor -Condition: unused -Manufacturer: SEW-Eurodrive, bevel gearmotor with brake -Type: K77 DRE132MC4BE11/TF -Translation: i= 7.24 -Speed: 203 rpm -Power: 7.5 kW -Protection class: IP55 -Shaft: Ø 50 x 100 mm on both sides -Brake: 55 Nm -Number: 1x motor available -Price: per piece -Dimensions: 860/410/H290 mm -Weight: 132 kg/piece Bdjdot Ult Aspfx Acysi

Condition: new, total power requirement 230 Volt Bdjdpjxaatnefx Acyji table diameter 300 mm table load 100 Horizontal kg swivelling range 0 - 90 Grad turning speeds 0,2 - 2,0 U/min turning speeds 1,2 - 12,0 U/min bore 20,0 mm weight of the machine ca. 50 kg dimensions of the machine ca. 480 x 325 x 470 mm Furnishing: - Precise drive unit with face plate, on a stable floor stand. - clockwise / counterclockwise - 2 speed series, stepless - Swivel range from 0 ° - 90 °. Manual tilt - DC gear motor with worm gear, infinitely variable. - diameter of 300 mm. Chrome-plated surface to protect against weld spatter. - The device's control panel is easy to understand and use. - Start / stop via a location-independent foot switch. - The speed and direction of rotation are set on the machine. - HF protected. Scope of delivery: - control (integrated) - foot switch