5-axis CNC inclined bed turning and milling center
The machine is almost new! - Test run only!
Main spindle hours: 1047 h
Main spindle C axis: 228 h
Advance items active: 968 h
Milling spindle active: 460 h
(New price in 2009 - Euro 1,700,000.00)
Siemens 840D CNC Control.
Swing diameter over the bed 1300 mm.
Swing diameter over the saddle 1250 mm.
Turning length 6000 mm.
Spindle bore 225 mm.
Chuck diameter 630 mm.
Spindle drive motor rating 78/87 KW.
Spindle speeds 10 - 1244 rpm in 2 gear ste...
pressure: 16 t
distance between columns: mm
stroke: 250 mm
throat: 270 mm
dayligth: ca. 400 mm
table surface area: 800 x 500 mm
boring diameter: Ø 50 mm
ram surface area: 220 x 360 mm
mortise hole in ram: Ø 40 mm
Bjrrtktxdl
table height over floor: 970 mm
voltage: 380 / 50 Hz V
control voltage: 220 V / 50 Hz
total power requirement: 3,0 kW
weight of the machine ca.: 2,3 t
dimension machine xH: 1,8 x 1,5 x 2,72 m
Press frame in robust welded construction.
Adjustment of the operating mode via swit...
Bench drill, bench drill, column drill, pillar drill, tapping machine
-Spindle mount: B13
-Clamping table: 360 x 280 mm
-Projection: 200 mm
-Speeds: 355-2000 rpm
-Column diameter: 80 mm
-Spindle stroke: 100 mm
-Motor power: 0.45/0.6 kW
-Motor speeds: 1360/2700 rpm
-on the machine base
-Number: 1x drilling machines available
-Price: per piece
-Dimensions: 550/600/H1950 mm
Myb7z
-Weight: 360 kg
turning diameter 570 mm
turning length 1000 mm
swing diameter over bed slide 360 mm
spindle bore 63 mm
speeds 11,2-2240 U/min
Hm27djkl8
feed 0,05 - 3,5 mm
total power requirement 11 kW
turning diameter max. 400 mm
turning length 600 mm
control 180i TB MG Fanuc
greates pass round over bed 500 mm
Swing dia. over traverse guideway 300 mm
centre distance 615 mm
Main spindle:
turning speed range - main spindle 20 - 6.000 min/-1
power capacity - main spindel 16 kW
max. Torque 155 Nm
spindle diameter in front bearing 100 mm
spindle bore 68,5 mm
max. bar capacity 52 mm
usable bar diameter 52 mm
spindle nose 140H5
max. chucking diameter 200 mm
C-Axis 0,001 °
Qd0emm8z
Subspindel:
...
No. 2109
f. double-sided room doors
Make Stehle
Dimensions 150 mm, 38-46 mm, 21-32 mm
HSS
30 mm bore
Storage location 97447 Gerolzhofen, free on truck, unpacked
Handover in the current condition as viewed,
without overhaul,
without guarantee and warranty
Vvbr80pp
table length 2100 mm
table width 1800 mm
table load 15 t
travel on the bed 1500 mm
total power requirement 12 kW
weight of the machine ca. 8 t
dimensions of the machine ca. 3,5 x 2,1 x 1 m
Bjt8gz87i
Rotary table with 9 T- slots in length direction. Each slot has a width of 28 mm.
faceplate diameter: 400 mm
width: 85 mm
boring diameter: 90 mm
total power requirement: - kW
weight of the machine ca.: 0,053 t
dimensions: 400x125 mm
Face Slidewith 2x 4 pcs clamping chucks (internal/outer) clamping travel 45mm
Bjmql3em
clamping area: internal dia. 120-400mm and outer diameter 120-330mm
flangeintake dia. size 160mm
equipment:
chuck key
Flange bearing
Mzos2
-Bore: Ø 20 mm
-Mounting hole: Ø 12 mm
-Bore distance: 64 mm
-Dimensions: 130/130/H50 mm
-Number: 16x available
-Price: per piece
-Weight each: 1.7 kg
All :available data
Model: Jig boring machine
Bbjkegqg
Manufacturer: Lindner
Type: LB15
Travel: 1000x600x250(150)mm
Table: 1200x700 (1000x600 t-slot)
MK20-30-40
With :Acu-Rite Digital
With multiple tooling and peripherals
Machine-dimensions: 2900x2150x2900mm
turning diameter over bed 2400 mm
turning diameter over slide rest 2200 mm
turning length 10000 mm
Control Sinumerik 840D
centre height 1500 mm
spindle bore 160 mm
max. workpiece weight 60 t
max. torque 110000 Nm
main drive 100 kW
total power requirement 145 kW
Machine is in a first class condition.
Faceplate dia. 1970 mm, dia. clamping area upto 1800 mm
Turning speed range in 3 steps: 1 - 300 rpm
Constant capacity in turning speed range: 11 - 300 rpm
Ebfpzwb
Equipment / Accessories:
- fac...
No. 2101
Dyiq39d
Make Stehle
used, good condition
Dimensions 150 mm x 80 mm
HSS
40 mm bore
Storage location 97447 Gerolzhofen, free on truck, unpacked
Handover in the current condition as viewed,
without overhaul,
without guarantee and warranty
grinding diameter:500 mm
grinding length:2000 mm
centre height:251 mm
max. workpiece weight between centers:500 kg
workpiece spindle head::5 MK
Bc29nj9q
tailstock quill taper MT:4 MK
Grinding wheel diameter / width / bore:400/100/127 mm
Grinding wheel motor:4 KW
Further technical data, and standard and optional equipment, as defined in Appendix.
Payment: 100% before loading of the machine
Warranty: no
turning diameter:650 mm
turning length:3000 mm
turning diameter over bed slide:350
bed width:550 mm
spindle diameter in front bearing:120 mm
spindle bore:71 mm
spindle motor:15 kW
spindle turning speed range:2 - 1800 U/min
rapid traverse:10/5 m/min
weight of the machine ca.:5,5 t
total power requirement:23 kW
dimensions of the machine ca.:4,1 x 1,9 x 2,1 m
Teach In controll R&D Euroturn
- 8-fold revolvong head SAUTER with VDI 40 taper
- C-axis 1° indexing driven tool 3000 rpm
- moveable splash...
Clamping plate with T-slots and cross table, plate field, welding table, welding table, plate boring machine, T-slot plate
-T-slot plate comes from a Kunzmann milling machine type: UFV 600
-Travel: 445 mm
-Width: 240 mm
-Length: 805 mm
Yu3e8zlb
-Height: 140 mm
-Plate thickness: mm
-Table height: mm
-Plate: is solid
-Groove width: 12 mm
-Dimensions: 1180/300/H140 mm
-Weight: 115 kg
x-travel:550 mm
y-travel:400 mm
z-travel:425 mm
control:Siemens 840
tool turret:20 Pos.
tool taper:SK 40
bore capacity in St 60 - full boring:20 mm
thread cutting up to max.:M 20
Bymzoogban
total power requirement:27 kVA
table surface area:640 x 400 mm
weight of the machine ca.:7,8 t
machine dimensions LxWxH:3,0 x 2,0 x 2,5 m
CNC verticak machining center with 2 pallet for serial parts,
chipconveyor,
oilmist suction,
prepared for 4th axis (2x),
internal coolant supply 25bar, 150l,
manuals,
bore depth 250 mm
number of spindles 1
core drilling diameter max. 1 - 30 mm
total power requirement 20 kW
weight of the machine ca. 2,5 t
dimensions of the machine ca. 3,2 x 2,8 x 2,0 m
Hg0v0rrr
Many accessories.
turning diameter 475 mm
turning length 1000 mm
control SIEMENS SINUMERIK 810 T
Bfmfew9kiz
turning dia. over face-slide 260 mm
centre height 235 mm
spindle bore 63 mm
turning speed range 10 - 2250 U/min
feeds 0,001 - 50 mm/U
rapid traverse X-axis 5 m/min
rapid traverse Z-axis 8 m/min
bed width 335 mm
tailstock quill diameter 80 mm
tailstock quill stroke 150 mm
workpiece weight max. 750 kg
face slide travel 300 mm
tailstock taper MT 5
weight of the machine ca. 3,0 t
dimensions of machine L x W x...
Turning and milling center
Byrkrleadi
Manufacturer Citizen Miyano
type BNJ-51 SY6
Control Fanuc Series Oi-TF
Year of manufacture 03/2018
9.923 switch-on hours
3.839 spindle hours
Main and counter spindle
8 controlled axes
2 turrets
2 x 24 stations of which 2 x 12 for driven tools
Speed of the driven tools 60 - 6.000rpm
turning diameter 165mm
turning length 246mm
spindle bore 51 mm
spindle speed max. 5.000U/min
Y axis -/+ 40mm
loading magazine FMB SL80S/1200A
Chip conveyor
Parts conveyor
Driven t...
Precision high speed punching press.
Bruderer BSTA 25.
Nominal capacity: 250 kN (25 ton).
Min./Max. number of strokes: 100/1500.
Max width of strip: 202 mm.
Variable stroke: 13 to 38 mm.
BBV 202/120 roll feed mounted on left-hand side.
Feed length variable up to 120 mm max.
Oil pump. Oil cooler.
Execution: 4 supports.
Front and rear safety guards.
Fitted with spring feet dampers.
Slide adjustment 51 mm.
Byri9i8o8a
Slide bore diameter 52 mm.
Table surface: Length 530 mm; Width 530 mm.
Passage...
Clamping bush, hydraulic clamping bush
-Type: ETP-EXPRESS R-25
-Flange: O 58 mm
Eundikh9
-Flange width: 14 mm
-Shaft: Ø 30 mm
-Shaft length: 35 mm
-Bore: 25 mm
-Dimensions: Ø 58/H49 mm
-Number: 4x available
-Price: per piece
-Weight: 0.27 kg/piece
- drilling spindles: 2
- min. drilling-Ø: 4 mm
B9a033glm
- max. drilling-Ø: 30 mm
- max. drilling depth: 250 mm
max. wheel diameter 630 mm
gear width 180 mm
max. module 8
min. module 1
table bore diameter 160 mm
no. of strokes 47 - 300 Hub/min
dia. of shaper cutter 125 mm
dayligth 100 - 330 mm
workpiece diameter 0 - 750 mm
stroke length max. 200 mm
total power requirement 12 kW
weight of the machine ca. 5,8 t
dimensions of the machine ca. 2,5 x 2,1 x 3,1 m
The design of the LORENZ S8 represents a further development of model S7/500,
which was successful over many years.
A considerable increase in dri...
Swing over bed - 360 mm
Swing over cross slide - 225 mm
Cross slide travel - 185 mm
Distance between centres - 1000 mm
Maximum cutting length - 900 mm
Spindle bore - 52 mm
Spindle nose - D 1-6 camlock
Spindle taper - MT4 in bush
Spindle motor - 5.75 kW (7.5 HP)
Spindle speeds - 50-4,000 rpm (2 ranges)
Tailstock travel - 150 mm
Tailstock taper - MT 4
Tailstock diameter - 60 mm
Bed width - 300 mm
Footprint L x D x H 2,300 x 1,370 x 1,810 mm
09smkibv
Weight 1,930 kg
YOM - 2021
Table type boring machine WH 10 CNC
Producer: TOS VARNSDORF
overhauled: 2021
Control Heidenhain ... TNC 620
Byreqhkcpa
Spindle diameter ... 100mm
Axis X ... 1250mm
Y axis ... 1120mm
Spindle speed ... 16-2500 / min.
Axis W ... 630mm
Axis Z ... 1000mm
ISO 50
Clamping table area ... 1120x1000mm
Machine weight ... 13000kg
Working feed of the X axis ... 2-4000mm / min
Main motor power ... 15kW
L x W x H ... 6130x3600x2750mm
The machine is in good condition and can be tested under power.
- Digital display, 3-axis
- Accessories available
- tool cabinet
centre height 200 mm
centre width 800 mm
turning diameter over slide/bed 240/425 mm
Length of cranking from the faceplate
with 4 jaws 180 mm
spindle bore 51 mm
inner cone 60 metric
Camlock D6" mounting
Speed 45-2240 rpm
Lead screw pitch 6 mm
Tailstock quill mount MK 4
Tailstock quill diameter 70 mm
Po3cx
quills: Stroke 200 mm
feeds:
Longitudinal 0.05-2.8 mm/rev
plane 0,05-2,8 mm/rev
Rapid feeds: Longitudinal
Thread pitches:
Metric ...
Catalog No. : 5506
Type: W 200 HA
Producer: ŠKODA
Made in: 1984
Plvk7
Characteristic:
Speed: 0.8-630 1/min
X-Axis travels: 15000 mm
Y-Axis travels: 3150 mm
Z-Axis travels: 1600 mm
Taper: M120
Spindle diameter: 200 mm
Maximum boring depth: 2000 mm
Power input: 77 kW
Equipment:
Rotary table (2x2m)
Floor plate (6400x5100mm)
Max. Turning diameter over bed: 1,500 mm
Max. Turning diameter in the gap: 2,000 mm
Length of the gap: 450 mm
Byrcxaikja
Max. Turning diameter over support: 1,150 mm
Max. Turning length: 9,000 mm
Spindle bore: 80 mm
Diameter of the face plate: 1,000 mm
Equipped with:
2 fixed steady rests (max.passage 450 mm), cone ruler, quadruple steel holder, etc.
The machine was general overhauled in 2014 and has not been used since. It is in very good condition!
.
Lathe with infinitely variable longitudinal feed .
.
Byrajhfn32
Center height 120 mm
Centre width 370 mm
.
24 speeds from 71 - 2240 rpm
Longitudinal feed infinitely variable from 6 - 450 mm/min
.
with :
Collet device
Boring vice
.
Machine is connected
.
.....
Manufacturer: Fermat
Type : WFT 13
SK50
Spindle dia: 130 mm
Max spindle speed: 3000 rpm
X = 4000 mm
Y = 2500 mm
Z = 1500 mm
Svgqmo
W = 730 mm
Clamping size: 1800x2200 mm
T Grooves
-Cooling throught center of tool
-Chip conveyor
- Probe Heidenhain TS-640
Machine size: 9000x6940x5350 mm
System: HEIDENHAIN iTNC640
Control Unit
Brand FANUC
Model Series 18i-MB
Main Drive
Spindle speed range 1200
Spindle motor power 29.41 kW
Movement
X-Axis Movement 8000 MM
Y-Axis Movement 4200 MM
Z-Axis Movement 1500 MM
Table
Outer length 2200 MM
Outer width 2200 MM
Tools
Btzcky9ic2
Type of tool holder BT50
Media
Main electronic connection 220 V 60 Hz
Chip conveyor Yes
This IKEGAI ANC 130FM Floor Boring Machine tool was rebuilt and retrofit in 2017 in Japan by IKEGAI HQ employees. It is equipped with a FANUC Series 18...
turning diameter over bed:400 mm
turning diameter over slide rest:250 mm
turning length:1000 mm
max swing over gap:520 mm
Height of centres:200 mm
crossed path:230 mm
bed width:218 mm
main spindle bore:52 mm
spindle size:MK 6
speeds::55-2000 U/min
turning angle of tool post:90 grad
tail stock:50 mm
taper in tailstock:MK 4
threading metric:0,4-7 mm
threading WHITWORTH:4-60 TPI
total power requirement:2,2 kW
dimensions of the machine ca.:1940 x 820 x 1545 mm
Gvej0o
weight of the machine ca.:75...
Catalog No. : 5481
Type: W 250 HA
Producer: ŠKODA
Made in: 1985
Characteristic:
Control system: MEFI
Power of the spindle drive: 77 kW
Minimum rotary speed of the spindle: 0.8 1/min
Maximum rotary speed of the spindle: 630 1/min
Travel length X-axis (mechanical feed): 8000 mm
Travel length Y-axis (mechanical feed): 6000 mm
Travel length Z-axis (mechanical feed): 1600 mm
I3glalj
Maximum feed rate in X-axis: 4000 mm/min
Maximum feed rate in Y-axis: 4000 mm/min
Maximum feed rate in Z-axis...
Max. Turning diameter over bed: 500 mm
Max. Max. turning diameter in the bed recess: 600 mm
Max. length of bed recess: 400 mm
Max. turning length: 3,000 mm
Speed range: 20- 2000 rpm
Bore of the main spindle: 63 mm
Equipped with:
FORKHARDT F500 three-jaw chuck
Quick-change steel holder system MULTIFIX TYPE C
Euwebbm7
Fixed steady rest
Coolant device
etc.
This machine is a precision lathe in a very good condition. With hardened, concealed guideways.
.
Heavy L+Z Lathe
.
centre distance 1500 mm
centre height 225 mm
Swing over bed 450 mm
Swing over cross slide 240 mm
spindle bore 52 mm
speed steps 7,1 - 1400 rpm
longitudinal feeds 0,056 - 1,6 mm/rev
face feeds 0,028 - 0,8 mm/rev
Spindle mounting DIN 55027 KK size 8
Tailstock mount MK 4
drive power 11 kW
width x depth approx. 3,6 x 1,35 m
Fq7g7rj
weight approx. 4,8 to
Equipment :
3-jaw chuck 250 mm , with inner and outer clamping jaws.
2 pieces bed stop
Multifix quick change holding head siz...
faceplate diameter: 500 mm
width: 100 mm
boring diameter: 90 mm
Mtuc3k
total power requirement: - kW
weight of the machine ca.: 0,07 t
face slide with 4 clamping chucks (clamping travel 60mm)
clamping area internal: 145-500mm and external 140-420mm
flange intake size= dia. 200mm with clamping bolts
equipment:
socket wrench
Control Unit
Brand Siemens
Model Sinumerik 840 D
Main Drive
Number of axis 4
Movement
X-Axis Movement 4000 mm
Y-Axis Movement 3000 mm
Z-Axis Movement 1500 mm
W-Axis Movement 750 mm
Table
Bwwpedls2s
Outer length 2000 mm
Outer width 2500 mm
Table load 20000 kg
This UNION KC 150 Boring machine was built in 2009. It is equipped with a Siemens Sinumerik 840 D control unit. It has a spindle diameter 150 mm. It includes tool magazine 40 pos and a spindle taper SK50. This 4 axis machine is in very g...
Clamping plate with T-slots and cross table, plate field, welding table, welding table, plate boring machine, T-slot plate
-T-grooved plate comes: from a Fluri milling machine type 14SE
-Width: 720 mm
-Length: 1200 mm
-Height: 235 mm
-Plate thickness: mm
Bagdjs3m0p
-Plate: solid
-Groove width: mm
-Dimensions: 770/1200/H235 mm
-Weight: 906 kg
Catalog No. : 5550
Type: W 200 HB NC
Producer: ŠKODA
Made in: 1986
Characteristic:
Control system: Siemens Sinumerik 840 D
Maximum lenght of the workpiece: 16000 mm
Max. workpiece width: 5445 mm
Max. workpiece weight: 140000 kg
Power of the spindle drive: 150 kW
Speed: 0.8-630 1/min
X-Axis travels: 8000 mm
Y-Axis travels: 2000 mm
Z-Axis travels: 4990 mm
Maximum feed rate in X-axis: 6000 mm/min
Maximum feed rate in Y-axis: 3000 mm/min
Maximum feed rate in Z-axis: 6000 mm/min
Taper: I...
Control: HEIDENHAIN MANUALplus 4110V2
Swing over bed: 800 mm
Swing over cross slide: 530mm
Slide travel plane: 395mm
Distance between centres: 2000mm
Spindle speed range: 1-1800 rpm
Spindle bore: 106mm
Spindle head DIN 55027 size 11
Main spindle drive: 40% ED kW 37 (digital AC motor)
Automatic eight-station tool turret
Gear stages Number 2
Brand new three-jaw chuck 630 mm diameter
The machine is in a workshop overhauled condition. The spindle of the Z-axis has been renewed!
Byrcuknxux
bore capacity in steel (diameter) 63 mm
boring head horiz. adjustable 1600 mm
throat 2000 mm
tool taper MK 5
feed range 0,04 - 3,2 mm/min
distance spindle center to column 450 - 2050 mm
distance spindle /table 400 - 1600 mm
stroke speed 1 m/min
pivoting angle 260 Grad
spindle turning speed range 20 - 1600 U/min
number of spindle speeds 16
feed range 0,04 - 3,2 mm/U
quill stroke 400 mm
horiz. adjustment of drilling head 1600 mm
Bmx0kvoe
total power requirement 5,5 kW
weight of the machine ca. 6...
faceplate diameter: 350 mm
width: 80 mm
boring diameter: 50 mm
Eed2sql
weight of the machine ca.: 32,0 kg
dimensions: 350x125 mm
face slide with 4 internal/outer clamping chucks (clamping travel 80mm)
clamping area internal: dia 110-350mm and external dia. 40 -300mm
flange intake dia. 130mm
Lathe chuck, power chuck RÖHM type KFD-HF 315/3
Ident. No.: 411193
Diameter 315 mm
Fz0ujex
Lathe chuck mounting short taper DIN 55027 size 8 with 4 mounting holes M16
Actuating force max 7000 daN
Speed max. 4500 rpm
Jaw mounting 90° pointed toothing 1/16".
Groove width of jaw mounting 21 mm
Total jaw width serration with groove 49,5 mm
Connection thread draw tube M90 x 2 mm
Central bore Ø 85 mm
- Lathe chuck mounting screwed to the chuck, short taper DIN 55027 size 8 (taper diameter approx. 139 ...
Multi-spindle head, multi-spindle drill head, drilling gear
-Multispindle head
-max.: 2x drill
-Max. Drill: Ø 13 mm
-Collets: Ø mm
-Variable drill spacing: from 31 mm to 145 mm
Csozxi8w
-Weight: 10 kg
Catalog No. : 5479
Type: PC W 200 HA
Producer: ŠKODA
Made in: 1987
Characteristic:
Power of the spindle drive: 77 kW
Minimum rotary speed of the spindle: 0.8 1/min
Maximum rotary speed of the spindle: 630 1/min
Travel length X-axis (mechanical feed): 5000 mm
Travel length Y-axis (mechanical feed): 4000 mm
Travel length Z-axis (mechanical feed): 1600 mm
Maximum feed rate in X-axis: 4000 mm/min
Maximum feed rate in Y-axis: 4000 mm/min
Bxsqllyd0f
Maximum feed rate in Z-axis: 4000 mm/min
T...
Control: SIEMENS 840D sl
turning diameter: 1300 mm
Distance between centres: 10.000 mm
center height: 750 mm
turning diameter over support: 820 mm
Y-axis: 210 mm
C-axis- incremental
I3gog3r
Speed range: 5-1200 min-1
Max. permissible torque: 8000 Nm
Spindle bore diameter: 120 mm
Turret with 12 fixed and 4 driven tool places
Max. Tool weight zbetween centers with a steady rest: 16t
Equipment:
- Operate software Operate
- 2 pieces of steady rests from RÖHM controllable
- 1 piece steady rest in C-sh...
turning diameter 370 mm
turning length max. 450 mm
control Sinumerik 840D sl Siemens
swing diameter 370 mm
Swing dia. over traverse guideway 370 mm
spindle distance 870 mm
Main spindle:
Max. rpm 6.000 min/-1
power capacity - main spindel 11 / 7,5 kW
max. Torque 220 / 150 Nm
spindle bearing diameter 110 mm
spindle bore 73 mm
max. usable bar diameter 51 mm
spindle nose A2-6 DIN 55026
C-Axis 360 °
Subspindel:
Max. rpm 6.000 min/-1
power capacity - Sub spindle 7,5 / 5,5 kW
Hecc3oxyk
max. Torqu...
faceplate diameter: 785 mm
revolution per minute: 4,5 - 180 (Planscheibe) U/min
Speed of boring spindles: 4,5 - 900 U/min.
tool taper: SK50
Gcvrfr7
weight of the machine ca.: 3,7 t
space requirements of the machine approx.: 3,6x1,3x1,6 m
spare part for a table type Boring and Milling Machine WMW BFT 130
with with headstock incomplete (as it can be seen on the picture!!)
- diameter facing of a flange:0-1400mm
- diameter for drilling: max. 800mm
- diameter at face turning: 0-1400mm
- spindle diame...
Gerolzhofen, Germany
(dealership location)